Search Documents

By Shahid Islam, Lucian Bogdan

There is a rapid expansion of world’s infrastructure and simultaneously existing infrastructure is aging. The maintenance of infrastructures has been of particular concern to the engineering community. Monitoring and evaluating the structures have become more significant than ever. Ground anchor is an important part of the structure where it is installed. Unfortunately there are limited testing methods available to assess the force in the pre-stressing steel. High cost, complicated equipment and limitation of space often prevent these methods from being implemented. DYNA Force sensors have been developed to measure the force in the pre-stressing steel during construction and at any time during the lifetime of the structure. These sensors make use of the magneto-elastic properties of ferrous materials. A readout unit is designed to magnetically energize the steel through the sensor and measure the response of the steel to the process. The readout unit then converts the response into a direct force reading. They can be used for bare, epoxy- coated, galvanized and greased-sheathed steel in the bonded, un-bonded, grouted or un-grouted length of the tendon. It measures the force of the steel element at the location where it is installed and can be recorded manually, automatically, or remotely. The sensor is robust, requires no maintenance and it is expected to have a similar service life to that of the surrounding structure. Sensors have received attention in terms of accuracy, performance, ease in installation, durability, and cost effectiveness. Sensor readings provide a second measurement, in conjunction with the jack pressure gauge, of the post tensioning force during initial testing procedure for ground anchors. This paper describes its application in tie-back and tie-down anchors and force monitoring of retaining walls, bridge abutment and dams where the data were collected manually, automated and remotely. INTRODUCTION Our infrastructure is expanding and the existing infrastructure is aging. Some structures are expensive to maintain and some occasionally fail. There is a large demand for implementing health monitoring of structures. Many tie-backs, retaining walls, dams and other geotechnical structures are post-tensioned and many of them need repair using a post-tensioned system. On many occasions during construction and service life of the structure, it is useful to know the force in the post-tensioning and anchor system. Many piles and drilled shafts are designed using reinforcing steel and the compressive forces in reinforcement are unknown. Although there are many methods to measure the tendon force, most of them are cumbersome, expensive, and the accuracy varies depending on the method used.

Jan 1, 2018

By A. R. T. Denues

The Explosives Division of the Bureau of Mines, United States Department of the Interior, is investigating cushioned blasting at the Explosives Testing Station, Bruceton, Pa. The general interests of this investigation are practical and relate particularly to safety. The immediate concern is an application of cushioned blasting in coal mining In cushioned blasting, various means are employed to reduce the intensity of the application of energy in an explosive action in a borehole. The primary object is to increase the efficiency of the use of explosives.

Jan 1, 1940

By A. R. T. Denues

The Explosives Division of the Bureau of Mines, United States Department of the Interior, is investigating cushioned blasting at the Explosives Testing Station, Bruceton, Pa. The general interests of this investigation are practical and relate particularly to safety. The immediate concern is an application of cushioned blasting in coal mining. In cushioned blasting, various means are employed to reduce the intensity of the application of energy in an explosive action in a borehole. The primary object is to increase the efficiency of the use of explosives.

Jan 1, 1940

By Jeremy Morris

The city of Indianapolis has more than 25,000 homes currently on septic systems. Many of these systems do not function well because of their age and surrounding soil conditions. As Indianapolis has worked to eliminate septic systems and install sanitary sewers in large unsewered areas on the north-west side, capacity of the existing Belmont North Interceptor (BNI) became a concern. The BNI system currently services an area of approximately 80 km2 (31 sq miles) located within the northwest quadrant of the city (Fig. 1). Monitoring of the existing interceptor indicated portions of the sys-tem flowing half- to two-thirds full during dry weather conditions and surcharging during some wet weather conditions. Further analysis of the BNI based on growth projections coupled with increased sewershed yield resulting from the city?s septic tank elimination program (STEP) indicated dry-weather flows could potentially triple over the next 20 years. Based on these modeling results and current wet weather capacity issues, the city determined further STEP projects could not be performed within the BNI service area until

Jan 1, 2011

By M Shaffer, D C. Grant, D J. Goudie, P Sylvester, C Voisey

Scanning electron microscope–Mineral Liberation Analyser SEM-MLA can be used to discriminate between hematite/magnetite in iron ores, but achieving backscattered electron (BSE) segmentation between the two minerals is difficult for particles =75 µm using typical preparation and analysis methods for the MLA based on a tungsten filament SEM (Quanta 400) with 25 kV high voltage. Preparing iron ore sample mounts using a slow-speed polishing method, and conducting the experiment on a field emission gun SEM-MLA (Quanta 650) with the high voltage (HV) setting lowered to 15 kV reduces instrument noise and results in very clean BSE images and segmentation. This method requires new X-ray standards to be acquired for each mineral identity at 15 kV because of major changes in the spectra at lower kV. However, once these X-rays are added to the mineral reference list, effective segmentation can be achieved and a proper analysis obtained.CITATION:Grant, D C, Goudie, D J, Voisey, C, Shaffer, M and Sylvester, P, 2017. Discriminating hematite/magnetite via scanning electron microscope–mineral liberation analyser in the - mesh size fraction of iron ores, in Proceedings Iron Ore 2017, pp 541–548 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By G. W. Jones

In a previous report,6 results were given that showed the amount of natural ventilation in a manhole having a capacity of 74.l cubic feet when the number of ventilation openings in the cover was varied. from no openings to a maximum of 48. The results showed that the ventilation (air changes per day) in the manhole was proportional to the area of the openings in the cover, and also that the number or area of the openings was the factor that chiefly affected the ventilation.

Jan 1, 1937

By B. J. Moore

This publication contains analyses arid related source data for 274 natural gas samples from 20 States. Of the total samples, 269 were collected during calendar year 1985; the reminder were collected earlier, but releases granting permission to publish were not received before 1986, All samples were obtained and analyzed as part of Bureau of Mines investigations of the occurrences of helium in natural gases of countries with free market economies. This survey has been conducted since 1917. The analyses published herein were made by mass spectrometer and chromatograph.

Jan 1, 1987

By Andrew Scogings

The current edition of The Australasian Joint Ore Reserves Committee (JORC) Code was published in 2012 and, after a transition period, the 2012 edition came into mandatory operation on Dec. 1, 2013. There is a significant change between JORC 2004 (Clause 44) and JORC 2012 (Clause 49) for the reporting of industrial mineral resources and reserves, which should be addressed by ASX-listed players in the industrial minerals space.

By Adilson Rodrigues da Costa

Os cilindros usados em laminadores a quente, especialmente os cilindros de trabalho são submetidos a altas taxas de desgaste da superfície durante a laminação. Após a campanha de laminação os cilindros devem ser enviados para uma retifica de cilindros para remover a camada danificada. Para este processo de retifica, são utilizadas rebolos com alta eficiência de corte e alta resistência. O objetivo foi analisar os resíduos metálicos e as partículas abrasivas do rebolo após a retificação dos cilindros e, correlacionar com o desempenho obtido com dois tipos diferentes de rebolos, sendo assim capaz de definir um rebolo com melhor desempenho e menor custo operacional.

Jul 30, 2018

By W. James Marold

The New Croton Aqueduct (NCA) was the first major water supply tunnel for New York City. The 50-km (31-mi) long tunnel has 33 open shafts 6 m (20 ft) to 121 m (397 ft) deep. The tunnel and shafts are lined with brick and mortar, with cast iron lining and pressure covers in six pressurized shafts. Details of the 1895 construction are provided and compared to modern construction techniques. The paper provides rehabilitation techniques for the shafts and pressure covers, including grouting, epoxy lining, temporary bulkhead design and installation and placement of tremie concrete 98 m (320ft) below the water level in a 122 m (400ft)deep shaft using a Remote Operated Vehicle (ROV) to monitor the placement.

Jan 1, 2008

By C. McCall, J. T. Knight, J. R. Ridley

Gold mineralisation in the gabbro sills is mainly stratabound to quartz- and Fe-rich, granophyric-textured units and is sited in undeformed, brittle quartz vein sets, which form pipe-like orebodies. Hydrothermal wallrock alteration consists of hornblende-plagioclase-calcite-quartz with minor biotite, garnet and chlorite and with arsenopyrite and pyrrhotite as the dominant sulphides. Geothermobarometric data suggest that gold was deposited at around 520 degrees C at 2.8-3.8 bar. Mineralisation is thought to have occurred during amphibolite-facies metamorphism. Fluid inclusion and isotope data indicate that gold mineralisation was the result of deposition from a low-salinity H2O-CO2-CH4 fluid of either metamorphic or magmatic origin. Although the Three Mile Hill deposit differs from others in the area in its wallrock-alteration assemblages, peak-metamorphic timing of gold deposition and distinct geochemical associations it forms a brittle stratabound ore body which suggests structural and gold-depositional mechanisms in common with those of the other gabbro-hosted gold deposits

Jun 18, 1905

By Stephen C. Tadolini, Dennis R. Dolinar

The risk of injury caused by minor roof falls continues to increase in underground mining. Most ground control injuries result from small rock falls that occur in a supported area, but do not involve the failure of the support system. In the roof, these are the "skin failures" that occur between previously installed primary or secondary bolting systems. To minimize skin failures and the associated accidents, several devices were designed and tested in the laboratory to maximize stiffness, minimize material thickness and weight, and ease material storage and handling on roof bolting machines. The goal of this project was to design and evaluate devices that can be installed with traditional primary or secondary roof supports, and that are easy to handle/install under temporary or previously supported roof.

[ ]

Jan 1, 2009

By Jürgen F. Brune, Liming Yuan, Alex C. Smith

To provide insights and assistances for the optimization of ventilation systems for U. S. under-ground coal mines facing both methane control and spontaneous combustion issues, a computational fluid dynamics (CFD) study is being conducted to investigate the effect of the ventilation scheme on the prevention of spontaneous combustion in longwall gob areas. This report focuses on the flow patterns within the gob under three different ventilation systems; one-entry and two-entry bleederless systems as well as a three-entry bleeder system. The gas flow in the caved gob area is simulated as a laminar flow through porous media while the gas flow in ventilation airways is simulated as a fully developed turbulent flow. The air flow patterns are visualized using flow path lines. Air velocity contours and vector data are also obtained. The possible location of critical velocity zones where the gob is most liable to spontaneous heating is discussed.

By Gordon Revey

The challenge of managing blasting risk, types of risk, public perception, and a system for managing risk were covered in the first part of this article in the May/June 2000 issue of the Journal of Explosives Engineering. This final part of this two-part series provides a method for identifying specific blasting risks and reviews the importance of community relations.

Jan 1, 2001

By F. Habashi

The first documentary evidence for the use of fire to extract a metal was furnished by the wall paintings of the ancient Egyptians showing workers using the blowpipe and bellows to increase the temperature to melt gold in a crucible. Furnaces grew in size and complexity, coke replaced charcoal in the blast furnace, and the Industrial Revolution took place in England that gradually spread worldwide. More metals became known and new techniques were introduced for their extraction. Among these, metallothermic reactions became prominent in the nineteenth century immediately after the discovery of the electric current and its use to liberate the alkali metals from their salts. Once these metals became available, they were used to produce aluminium from alumina that resisted all other methods of attack. Aluminium, now available on a large scale, was used to decompose the most stable compounds and liberate more metals that became the basis of modern civilization.

Jan 1, 2004

By J. L. Collins

"Une recherche debutee en 1987 tente de cerner divers éléments ayant un impact sur la productivite miniére, de facon à améliorer la planification des operations souterraines. II a été possible de recueillir jusqu'à trente variables dans sept opérations minières differentes du Nord-Ouest québécois. Cette présentation rend compte de quelques résultats préliminaires obtenus à l’une d'entre elle. Entre autres, elle montre comment une association entre une analyse de régression multiple et un logiciel d'optimisation (OPTIMUL) peut servir à une application particulière de la planification d'une opération minière du Québec. Plus spécifiquement, la présentation montre comment une quantité appropriée de ANFO et de TOVEX peut maximiser la quantilé de minerai cassé, minimiser les couts de sautage ou encore minimiser les coûts d'explosifs par tonne de roche cassée, en se basant sur une série de contraintes réalistes provenant de la mine.ABSTRACTA study, underway since 1987, tries to evaluate factors affecting mines' productivity. Information has been collected from seven underground mines in Quebec and this paper shows preliminary results from one. In particular, it shows how a combination of multiple regression analysis, mathematical programming and a set of realistic mine constraints can be used for a particular application of mine planning. More specifically, the paper shows a parallel between maximizing production of tons of broken are, minimizing explosives costs or minimizing the costs of explosives per ton of broken are by an appropriate selection of ANFO and TOVEX quantity of explosives. Finally, the paper shows that minimizing the costs of explosives per ton of broken are is the best alternative to follow providing a special optimization program can be set up."

Jan 1, 1990

By L. E. Mordberg, E. N. Nesterova

Geochemical studies of the bauxite deposits show that the primary composition is gibbsitic. Some trace elements were relatively mobile during bauxite formation with the content of Th, U and Zr increasing and that of Rb, Ni and Co decreasing. Y and Pb were relatively immobile during lateritisation; their contents and ratios were inherited from different types of underlying rocks. The supply of Ni and Co took place at the diagenetic or epigenetic stages; their ultimate source was the crystalline basement in the region. The studies support the view that the bauxite was likely to have originated as a result of in-situ lateritisation and not through sedimentary transport and redeposition

Jun 18, 1905

By L. J. Terrill

Lateral displacement in the immediate roof beam at the Waste Isolation Pilot Plant (WIPP) is a significant factor in assessment of excavation performance for the design of ground control systems. Information on roof beam lateral displacement, expansion, fracture formation, as well as excavation convergence, is gathered using a variety of manually and remotely read instruments. Visual observations are also used when possible. This paper describes the methods used to measure lateral displacement, or offset, at the WIPP. Offset magnitudes are determined by the degree of occlusion in drillholes that intersect the offset plane. The Borehole Lateral Displacement Sensor (BLDS) was developed for installation at WIPP to monitor offset at a high degree of accuracy at a short reading frequency. Offset measurements have historically been obtained by visual estimation of borehole occlusion. Use of the BLDS will enable relationships between time dependent roof beam lateral displacement and expansion to be established in much shorter periods than is possible using visual observations. The instrument will also allow remote monitoring of roof beam displacement in areas where visual estimations are not possible. Continued monitoring of roof beam displacement, convergence, and expansion, is integral to timely and pertinent assessments of WIPP excavation performance.

Jan 1, 1996

Validation and Simulation of Optimised Compressive Crushing Ores and aggregates are used in countless applications all around in the society. The frequent and escalating usage of these natural resources requires efforts aimed at not only making do with what is available, but also undertaking actions to improve the production yield and the processes involved. This strive to improve the performance and efficiency of existing crushers and crushing processes has brought about research concerning optimisation of crushing plants as well as theoretical optimisation of crushing. Previous work shows that different applications and different materials require different compressive crushing in order to accomplish a theoretically optimal size distribution. These optimisation results, obtained by genetic evolutionary algorithms and evaluated with so called fitness functions, convey the theoretically optimal number of compressions and their corresponding compression ratios. Presented in this paper are thus some laboratory crushing tests, which are conducted in order to validate a set of previously optimised crushing sequences. More specifically, interparticle crushing sequences are carried out in a Piston-die testing equipment, where samples are sieved between each compression. The subsequent analysis of these results shows good correlation with model predictions, which combined with a comparative study between presented optimisation results and measured data from a real crusher indicate a significant potential for improvement. However, before redesigning crushers according to what is theoretically optimal, the resulting impact as well as the effects on the outcome of a crushing plant must be examined. Crushing plant simulations using the software PlantDesigner« are consequently performed. Models of existing crushers are altered, resulting in changed particle size distributions from some of the crushers in a crushing plant. Thence, it is concluded that significant gains can be made in terms of capacity, process yield and energy consumption.

Sep 13, 2010