Search Documents

By Thornton L. Neathery

Vertical magnetic surveys have been made over about 3, 150 miles of the crystalline area of east-central Alabama. A contour map (100-gamma interval) showing regional magnetic anomalies has been prepared (scale 1:250,000) from data points located at quarter-mile intervals on all public roads. Small one- and two-station anomalies were eliminated, leaving only areally extensive anomaly features associated with regional geology. The regional gradient was "filtered" from the basic data and the resulting magnetic configuration compared to the regional geology. Regional lines of vertical magnetic intensity trend northeast and follow the structural framework of the area. Correlations can be made between a large number of geologic and magnetic features. The strongest regional anomalies are associated with the Goat Rock, Bartletts Ferry, Towaliga, and Brevard fault structures. The Inner Piedmont area is characterized by a broad regional high. The magnetic values of the northern Alabama Piedmont grades gently northwestward, disrupted occasionally by elongate highs and lows associated with amphibolites or granites. Scattered throughout the Piedmont are anomalous areas of high magnetic intensity; some are related to magnetic-bearing rocks, and some Indicate possible mineralization. Most of the anomalies have not been evaluated,

Jan 1, 1972

By K. Drescher

Excavations in deep level hard rock mines show rheological or time-dependent deformation responses to mining-induced stresses. These are generally not as dramatic as those seen in soft rock environments, such as potash and salt mines, but these deformations can nevertheless become substantial in time. It is usual to see total excavation closure at a much earlier stage than predicted by numerical models, and real-time measurements underground have confirmed that closure takes place on a more-or-less continuous basis, with highest closure rates observed after a blast and then slowly diminishing with passing time. This paper describes laboratory tests to determine the time-dependent response of hard rocks to loading, the results of the tests, and then quantifies these effects to explain the time-dependent phenomena observed underground. The primary intention of this work is to help explain the various time-dependent deformation processes around typical deep level hard rock tabular excavations. Three mechanisms were investigated in two typical hard rock types present in the deep level gold mines in South Africa, namely Ventersdorp Lava and Elsburg Quartzite. Uniaxial compression creep studies were done as the first part of the study followed by shear creep studies on discontinuities where crushed lava and crushed quartzite as well as a natural gouge were used as infilling. The last part of the study consisted of triaxial post-failure relaxation tests. The compression creep tests and the triaxial post-failure relaxation tests showed that the amount of energy dissipated by the lava is significantly less than for quartzite. For mines operating at depths greater than 2000 m the implication is that the lava must show a greater rockburst-proneness than the quartzite. Since the lava shows a lower post-failure stress relaxation, it can store sufficient energy for multiple rockbursts, which is seen in the clustering of multiple seismic events in the deep level mines. This study provides the first data available for energy change calculations in fractured rock masses, and provides the first general indications for rockburst intensities ahead of active mining faces.

Jan 1, 2003

The key aspects of process metallurgy that distinguish platinum group metal (PGM) concentrate smelting from that of other base metal sulphide concentrates are presented. These differences include considerably higher input chrome and magnesia contents that directly raise the slag liquidus temperature and have the potential to increase accumulations of refractory spinels. Most importantly, the higher processing temperature required for PGM smelting, and the resulting very high matte superheat lead to considerably more onerous smelting conditions than those typical of other smelting operations. This has presented challenges to furnace design and integrity, especially when coupled with the progressive intensification of smelting, involving doubling, and then redoubling, of furnace power input over the past 20 years. These power increases have been enabled by increasingly more advanced furnace cooling and structural technologies. Key technologies include strong constant-force spring-loaded bindings acting in three dimensions to minimize infiltration of superheated matte into brick joints, and robust well-cooled tapholes for reliably tapping the superheated matte. The result has been substantially improved productivity, and reduced smelting capital cost outlay per unit of production. A significant challenge that was not anticipated, presented itself in the form of insidious corrosion of the furnace lining, and especially high-intensity copper cooling elements. Investigation of corrosion in related industries eventually identified 'chloride-accelerated sulphidation', and this term has been retained as it generically describes the most pertinent aspects of the accelerated low-temperature wear of copper coolers observed in PGM smelting. In addition to discussing the corrosion mechanism, this paper describes a number of solutions that were developed jointly by Anglo American Platinum and Hatch to address the copper corrosion problem. First, new monitoring technologies allowed furnaces to be operated more safely for a longer period of time. Second, a system for replacing corroded coolers from outside the furnace during a fast 'hot' shutdown minimized the impact on furnace operating factor and hearth life. Finally, a corrosion-resistant graphite-protected cooler design significantly improved furnace campaign life, and heralds a more lasting solution to cooler corrosion in PGM furnaces.

Jan 1, 2012

By Sri Sawmliana, P. Pal Roy

Blasting Gallery (BG) method was introduced in India for higher production and low cost of excavation to substitute conventional hand section and stowing methods for thick coal seam. The Singareni Collieries Company Ltd. (SCCL) adopted this method in the year 1989 and since then successfully operating at GDK-10, GDK-8 & VK-7 Incline mines in Andra Pradesh, a southern state of India. It is also successful at Chora 10 Pit Colliery of Eastern Coalfields Ltd. (ECL) in West Bengal whereas at East Katras Colliery of Bharat Coking Coal Ltd. (BCCL) in Jharkhand State, the method has been partially successful due to some geological constraints of the area.

Jan 1, 2003

By J. N. Van der Merwe

"A major shortcoming of the statistical back-analysis of coal pillar strength is that it relies on the asmined pillar dimensions, not taking into account time-related pillar scaling with subsequent reduction in pillar width. The paper describes an investigation where the rate of pillar scaling was applied to the pillars in the databases of failed and unfailed pillars. The reduced pillar sizes were then used in the same method of statistical back-analysis that had been used in the past.This resulted in an equation for pillar strength which predicts significantly greater pillar strength than the previous statistical analyses, which is similar to the strength which had been found earlier by direct testing of large specimens underground. It is concluded that the lower strengths found by previous statistical analyses are due to the incorrect pillar width being used and that by adjusting the pillar sizes to compensate for scaling, more credible results that correspond to direct testing are obtained.As the newly derived strength equation is time-dependent, it follows that the safety factors and probabilities of failure are likewise time-dependant. An equation to determine the probability of failure is also developed. This results in the safety factor being close to unity at a probability of failure of 50%, which is aligned to statistical expectation. IntroductionSince the Coalbrook mine disaster, caused by massive pillar collapse, there have been several attempts at analysing and defining the strength of coal pillars. It was realized in the very beginning that performing classical strength tests on coal specimens in a laboratory and then transferring those results to real coal pillars could not be successful. The scatter of results is one problem and, more seriously, there is a size effect (at least for small specimens) that made the transformation of strength results to much larger coal pillars underground all but impossible.Two main schools of thought then emerged. Some researchers preferred to perform direct strength tests on large specimens underground, while others relied on statistical back-analysis of failed and unfailed pillar cases, attempting to determine the differences in size and shape that would allow a satisfactory prediction of failure. The latter school of thought resulted in the method that was widely accepted by the South African coal mining industry, described in the landmark publication by Salamon and Munro (1967)."

Jul 1, 2019

By Siderley Fernandes Albuquerque

Devido à descoberta de petróleo em um gigantesco reservatório situado na região litorânea entre os estados de Santa Catarina e Espírito Santo, a malha dutoviária brasileira irá aumentar consideravelmente nos próximos anos, assim como a necessidade de novos sistemas dutoviários capazes de transportar óleo e gás a pressões cada vez mais elevadas. A soldagem de tubulações no Brasil ainda é realizada de forma manual com processo ao Arco Elétrico e Eletrodo Revestido, fortemente dependente da habilidade do soldador; com a utilização de soldagem robotizada, tem-se maior controle dos parâmetros de soldagem, com possibilidade de obtenção de juntas de boa qualidade, além do ganho considerável em produtividade. O objetivo deste trabalho é analisar a tenacidade ao impacto charpy na ZTA de juntas soldadas do aço API 5L X80 utilizadas para transporte de petróleo quando submetidas a processo FCAW-G robotizado com o arame AWS E111T1-K3MJ-H4 para passes de enchimento e acabamento, com Ar + 25%CO2 como gás de proteção, e processo GTAW com o arame ER80S-Ni1 para passe de raiz, utilizado Ar + 25%CO2 como gás de proteção. Os resultados obtidos são comparados com o processo SMAW manual, utilizando como consumíveis os eletrodos AWS ER 7018 e E9010-G; as soldagens foram realizadas na posição plana e vertical ascendente; com os resultados obtidos de energia absorvida em ensaio de impacto charpy, com entalhe localizado na ZTA, foram correlacionados estes valores com a microestrutura presente na ponta do entalhe dos corpos de prova.

Aug 16, 2017

By R. C. Earlougher

Jan 1, 1970

By R. W. Baker

"The development of uppers drilling at Brunswick Mining is reviewed. This paper describes design criteria for drilling patterns and the research required for selection of a suitable drill jumbo. The success of the uppers drilling program based on operating procedures is highlighted. IntroductionBrunswick Mining and Smelting Corporation Ltd., operates a 10 500 tonnes per day lead /zinc/copper I silver underground mine some seventeen miles southwest of Bathurst, New Brunswick .The No. 12 orebody, first discovered in 1952 by a group headed by M.J. Boylen, had extensive development, including two shallow shafts (500 ft), and test work carried out on it by St. Joe Lead between 1953-1957. However due to complex metallurgy and depressed metal prices, the operation was suspended.In 1961, a group comprised of M.J . Boylen, K.C . Irving and Patino acquired the rights of St. Joe Lead to the No. 12 property. A concerted development plan was initiated along with construction of the necessary sur face facilities and by July 1964, the property was in production at 4500 tons per day.In 1967 Noranda Mines Ltd. acquired operating control of Brunswick Mining and Smelting Corporation Ltd."

Jan 1, 1988

By Barbara Mazzini Loureiro

As placas de circuito impresso (PCI) são materiais heterogêneos e sua composição pode variar em função do ano de fabricação, tecnologia empregada, propósito de utilização, legislações vigentes e país de origem, entre outros. Essas características interferem diretamente no valor econômico agregado a estes resíduos, pois dependem da composição dos mesmos, de tal maneira que as empresas recicladoras tomam como base essas informações no momento da aquisição da sucata. Assim, a classificação e caracterização de PCIs é de suma importância para o mercado de reciclagem de resíduos eletroeletrônicos. A fim de alcançar este objetivo foi realizada cominuição em moinho de facas utilizando grelhas com abertura de 9, 6 e 3mm. A etapa de caracterização incluiu ensaios de digestão em água régia, perda ao fogo, análises química quantitativa por ICP-OES e MEV/EDS. Verificou-se que o lote de PCI estudado possui 39,5% de material cerâmico, 34,5% polimérico e 26 % metálico. A porcentagem em massa de cobre na placa é de 14,28%, de ferro 3,73%, de ouro 0,012% e de estanho 1,29%. O lote não é lead free e é multilayer com quatro camadas de cobre.

Aug 8, 2018

By B. J. Moore

This publication contains 14,242 analyses of gas samples from oil and gas wells and natural gas pipelines in 40 States and 24 foreign countries. These gas samples were collected in the period 1917-85 as part of the Bureau of Mines survey for helium occurrences. The gas analyses contained herein were made by several methods over the period covered. Analytical work on samples collected early in the period was done on the Orsat apparatus. The one-cut apparatus and four-cut fractional distillation equipment were added later. A mass spectrometer was acquired in 1949 and used for all gas analyses made after that time. From 1917 to 1978, helium analyses were made on special helium analytical equipment designed and built by the Bureau of Mines Helium Operations Laboratory. In 1978, this apparatus was replaced in the quantitative helium analysis work by a gas chromatograph.

Jan 1, 1987

By J. C. W. M. de Wit

An excavation, within which a tunnel is sunk as a part of the Centraal Station underground station (platform section) of the Noord/Zuidlijn ('North/South Line'), is to be created beneath the Amsterdam Centraal ('Amsterdam Central') station. The section beneath Amsterdam Centraal Station is characterised by the application of a particular technology in the form of, inter alia, the so-called 'sandwich wall'. This is a composite wall consisting of two rows of Tubex piles with a body of jetgrout columns in-between. This wall acts both as an excavation support wall and also provides vertical bearing. The installation of the wall, including both Tubex piles and jetgrout columns, within these specific conditions (limited height, sensitive historical building), within the design requirements set in terms of construction tolerance and water and soil retention, may be regarded as being a pioneering achievement. The environmental constraints are that the trains should continue to run, the inconvenience to passengers should be kept to a minimum and the historic station should not suffer any damage. Because of the complexity of the working conditions, the project is being overseen by a steering group of experts in the specified construction processes. In order to manage the project risks, jet grouting trials were initially carried out, in order to highlight and control execution problems; the practicability of the design is then tested. Work commenced on the sandwich wall in 2003, when the wooden piles were extracted at the locations where the sandwich wall was to be constructed; in 2004, the steel Tubex piles for the southern wall sections were installed. From May 2005, the construction of the sandwich wall got under way; in addition to the described process supervision, an extensive measuring programme was established, so that the process could be adjusted as necessary and the quality of the finished product determined. This applied to both individual columns and for the end product, the sandwich wall. The measurement results were processed for each column, interpreted and the effect on the work still to be conducted was assessed for each future column. Preventative and corrective measures were, if necessary, taken in order to control or counteract the measured defect. In addition to the process-oriented and qualitative measurements, various independent measurement systems at the station building served as a further control in order to prevent damage to the building.

Jan 1, 2006

By Joel Lööw, Jan Johansson, Lena Abrahamsson

Industry 4.0 offers new possibilities to combine increased productivity with stimulating workplaces in a good work environment. Used correctly, digitalization can create attractive jobs in safe control room environments, which provide space for the employee’s full expertise and creativity. This is true also for the mining industry. But, to succeed, it is important to analyze the development from a worker’s perspective. What will happen to their work? What skills will be needed in the mine of tomorrow? We must also consider the risks, such as privacy issues, increased stress, and work-life boundaries. These questions must be understood if we are to create workplaces that can attract a young and diverse workforce to tomorrow’s mining industry. In this article, we try to illustrate what the new technology can mean for the individual miners. We formulate the notion of Mining 4.0 (Industry 4.0 in the mining industry), where we try to create an image of how the future might look from a miner’s perspective and how mining companies may navigate their way to a future that works for all miners. To illustrate the range of possible outcomes, we formulate two scenarios: one utopian and one dystopic. At the end of our article, we bring forward six recommendations that can be considered a beginning of a road map for the human side of Mining 4.0.

By Joel Lööw, Jan Johansson, Lena Abrahamsson

Industry 4.0 offers new possibilities to combine increased productivity with stimulating workplaces in a good work environment. Used correctly, digitalization can create attractive jobs in safe control room environments, which provide space for the employee’s full expertise and creativity. This is true also for the mining industry. But, to succeed, it is important to analyze the development from a worker’s perspective. What will happen to their work? What skills will be needed in the mine of tomorrow? We must also consider the risks, such as privacy issues, increased stress, and work-life boundaries. These questions must be understood if we are to create workplaces that can attract a young and diverse workforce to tomorrow’s mining industry. In this article, we try to illustrate what the new technology can mean for the individual miners. We formulate the notion of Mining 4.0 (Industry 4.0 in the mining industry), where we try to create an image of how the future might look from a miner’s perspective and how mining companies may navigate their way to a future that works for all miners. To illustrate the range of possible outcomes, we formulate two scenarios: one utopian and one dystopic. At the end of our article, we bring forward six recommendations that can be considered a beginning of a road map for the human side of Mining 4.0.

By David E. Thompson

This paper describes the full-scale field load testing of three deep foundation units using the Osterberg Load Cell. The load tests were completed on three separate projects, two in Massachusetts and one in New York. The Massachusetts projects involved the load testing of two 18-inch O.D. concrete-filled steel pipe piles over water for railroad bridge reconstruction projects in Revere and Saugus/Lynn. The New York project involved the load testing of a 24-inch diameter drilled shaft socketed into sandstone on land for a building foundation in Rochester. The 18-inch O.D. piles were loaded to failure at jack pressures of 142 to 215 tons. The drilled shaft was loaded to failure at jack pressures of approximately 450 tons. The loading testing procedure is described and the results of the three tests are presented. The advantages and disadvantages of the Osterberg load cell for load testing of deep foundations are discussed.

Jan 1, 1989

Leinster Nickel Operations, located in Western Australia, consists of an underground and three open pit mines in relatively adverse ground conditions. This paper reviews our ground control practices in the open pits, covering aspects of ground support, wall control and monitoring. These methods have been effective in allowing mining operations to continue beneath unstable slopes. In particular, the use of Ground probe?s slope stability radar has enabled the Harmony open pit to safely operate for months following indication of failure from traditional methods. This case study highlights the benefits of investing in appropriate slope stability monitoring systems.

Jan 1, 2006

By G. M. Bond

Reduction of the emissions of greenhouse gases, such as CO,, is currently the subject of extensive research. A novel strategy is put forward here, based on a biomimetic approach providing accelerated deposition into carbonate form for long-term sequestration. It offers the advantages of a process that: does not require concentration of CO, from flue gases; could potentially be used in an on-site scrubber to provide a plant-by-plant solution to reducing CO, emissions; is an environmentally benign procss with an environmentally benign product; and is based on readily available, low-cost reagents (except perhaps the catalyst).

Jan 1, 1999

By P. Nicholls

Though the burning of fuels extends far back into antiquity, and though fuel beds are the most common and widely distributed example of chemical actions and engineering practice, there has been little attempt to group fuel beds by types or to define the principles associated with them. This paper does not profess to cover completely the subject of fuel beds. It suggests some of the over-all principles of the two more common types. No new investigational data are included, but the deductions are largely based on a recent publication of the U.S. Bureau of Mines'. Definition of Types There are three primary types of fuel beds: (I) Underfeed, in which the fuel and the air move in the same direction; (2) overfeed, in which the fuel and the air move in opposite directions; (3) crossfeed, in which the fuel and the air move at right angles to each other. The principle that fixes the type is the relation between directions of the flow of fuel and of air. Fig. 1 shows the three types diagrammatically. All other types are compounded of these three in a simple or more or less complex manner. It does not follow that these three type designations are limited to the methods used in representing them in Fig. 1; they may be turned in any direction, and as long as the relative directions of the fuel and air are the same the type is not changed. For example, A as shown .resembles a pot-type stoker, but the air and fuel can move downward as in the so-called smokeless heating boiler furnace. Also, C can be placed horizontal, as in chain-grate stokers. For this reason, the terms used to designate the three types are not all that could be desired; more logical ones could be coined, but those used probably are satisfactory until the discussion of fuel-bed types becomes more common.

Jan 1, 1936

By P. Nicholls

Though the burning of fuels extends far back into antiquity, and though fuel beds are the most common and widely distributed example of chemical actions and engineering practice, there has been little attempt to group fuel beds by types or to define the principles associated with them. This paper does not profess to cover completely the subject of fuel beds. It suggests some of the over-all principles of the two more common types. No new investigational data are included, but the deductions are largely based on a recent publication of the U.S. Bureau of Mines'. Definition of Types There are three primary types of fuel beds: (I) Underfeed, in which the fuel and the air move in the same direction; (2) overfeed, in which the fuel and the air move in opposite directions; (3) crossfeed, in which the fuel and the air move at right angles to each other. The principle that fixes the type is the relation between directions of the flow of fuel and of air. Fig. 1 shows the three types diagrammatically. All other types are compounded of these three in a simple or more or less complex manner. It does not follow that these three type designations are limited to the methods used in representing them in Fig. 1; they may be turned in any direction, and as long as the relative directions of the fuel and air are the same the type is not changed. For example, A as shown .resembles a pot-type stoker, but the air and fuel can move downward as in the so-called smokeless heating boiler furnace. Also, C can be placed horizontal, as in chain-grate stokers. For this reason, the terms used to designate the three types are not all that could be desired; more logical ones could be coined, but those used probably are satisfactory until the discussion of fuel-bed types becomes more common.

Jan 1, 1936

By Catia Casagrande

As principais operações unitárias de um processo de pelotização são: moagem, filtragem, aglomeração e queima. Das etapas citadas, a moagem, como início do processo, é uma etapa crucial para as demais operações. Foi baseado neste fato, que o presente estudo foi realizado, tendo como objetivo principal, avaliar o comportamento das misturas de minério de ferro com diferentes índices de moabilidade e definir os possíveis ajustes dos parâmetros de processo de moagem em função dos diferentes perfis mineralógicos. Foram usadas três misturas de diferentes níveis de índices de moabilidade: baixo, médio e alto, a fim de observar as respostas nas variáveis operacionais de possível atuação na rotina operacional. Para isso, uma matriz de experimento foi realizada, com oito testes para cada mistura de minério de ferro, variando os parâmetros de moagem de mínimo a máximo. As variáveis respostas foram às características físicas das misturas, superfície específica e granulometria, onde foram medidas no sistema automatizado PSI. Através dos resultados dos testes, foram calculados modelos matemáticos de superfície específica e granulometria das misturas em função dos parâmetros operacionais. Os modelos mostraram satisfatórios e aplicáveis, apresentando correlação entre as variáveis dependentes e independentes.

Aug 1, 2018

By D. P. Bryan

An aggregate resource study was done for southern Washoe County, Nevada, which contains the Reno-Sparks metropolitan area and a population of about 300,000. The study included an inventory of existing operations, projection of future demand, identification of potential aggregate resources based on geology, and determination of economic potential of these resources. Economic potential was determined by the integration of GIS layers that included aggregate potential, distance from market, distance from major and minor transportation arteries, and elevation. The investigation resulted in a determination that resources of high quality aggregate sufficient for future consumption are present in southern Washoe county; the limiting factor for future utilization is accessibility.

Jan 1, 1996