Search Documents

By O. W. Ellis

Introduction During the month of September, 1928 enough money had. been promised by private individuals and corporations to comply with the Research ?Foundation Act 1928 (Chapter 57, 18 George V) of the Province of Ontario. The Ontario Research Foundation (referred to below as O.R.F.) may be said to 1iave come into being at that time. Under the terms of this Act, the Treasurer of the Province was empowered to match dollar for dollar of the sums subscribed by private .corporations and individuals up to a limit of $1,000,000. However, the response to the appeal for this by the Premier of the Province, the Honourable Mr. G. Howard Ferg uson, was so exceptional that the Act was amended in 1929 so as to empower the Treasurer to increase the maximum contribution on the part of the Province to $2,500,000. In March, 1933, the Chairman of the Foundation, Sir Joseph Flaville, Bart., was able to report that, in the interval between the Premier's appeal and December 1st, 1932, private enterprise had paid ?into the treasury of the Foundation $1,670,050, and that the Provincial Treasurer had assumed responsibility for a like sum. The endownment Fund of the Foundation was, therefore. $3,340,100. This sum was ?invested a lm~ s t entirely in Government securities, in securities guar. anteed by the Government, and in 1mmicipal securities. Sir Joseph Flavelle remarked at that time that "The payment of $1,670,050 to the Endowment of the Foundation by private persons and corporations is a somewhat remarkable performance when it is remembered that for three of the five years the business of the country has been suffering from a severe depression". Since that time it has been the consistent policy of O.R.F. to live within the income derived (1) from the investment of its Endowment Fund and (2) from fees collected for services rendered.

Jan 1, 1950

By C. M. Diaz, P. J. Mackey

Since its inception, in 1987, the Copper-Cobre series of conferences has established itself as the prime world forum for discussing advances in copper process metallurgy, in particular copper sulfide smelting, copper recovery by leaching and electrowinning and copper electrorefining. All copper producing countries have actively participated in the pyrometallurgy symposia held in the framework of these conferences. In 1999 and 2003, the close to 100 pyrometallurgy papers that were presented had to be accommodated in two volumes. In the present paper, the authors firstly provide a brief historical sketch of the Copper-Cobre conferences and then focus on providing a retrospective look at the dramatic changes that have taken place in copper smelting in the last few decades, primarily as discussed in the Copper-Cobre and precursor conferences pyrometallurgy proceedings. Topics include: the development of autogenous, increasingly more intensive, environmentally sound and energy efficient smelting processes; significant improvements in Peirce-Smith converting practice and at the same time the commercialization of alternative continuous converting routes; the consequent expansion and modernization of smelters; the increasing compliance with strict government environmental regulations in most copper producing regions of the world; the realignment of the copper smelting industry throughout the world; and trends in copper smelting R&D. A look at the future closes these reflections on the contribution of the Copper-Cobre conferences to the advancement of copper smelting technology.

Jan 1, 2007

By Martin P. Raffield

Placer Domes? Campbell Mine, situated in northwestern Ontario, is undergoing an assessment of the efficiency of the operation which is necessitated by the low gold price and a reducing ore reserve grade. A decision has recently been taken to move away from a functional based departmental structure (underground, engineering, geology, etc.) towards a team-based system where crews, engineers, geologists and supervisors are responsible for the planning and operation of a particular area of the mine. The objective is to improve communication and understanding of the goals and achievements and to ensure a forum is available for the generation of ideas. It is intended to increase the accountability and decision-making ability of the teams in an effort to achieve the mines? safety and production targets. This paper presents a critical review of the progress of this organisational change process and its successes and failures at the time of writing.

Oct 1, 2001

By L. Bos

The availability and reliability of large grinding mills and their Gearless Mill Drives (GMDs) are of paramount importance for the grinding process. Although GMDs have been in service for decades, and are known for their operational efficiency (reliability and robustness with reduced operating cost per ton), compared to conventional drives, in the last decade due to certain reasons some failures led to serious unscheduled shutdowns and significant insurance events. The majority of these notable "insured" failures have happened on GMDs installed on relatively large mills, as the financial impact of a failure is proportional to the through-put of the mill. Despite the occurrences of these events, as mining operations are driven by lower ore grades and the ability to continue reducing operating costs per ton, the trend for having larger mills is still very present and there is no reason why this trend should not continue. It is obvious that if not handled correctly, the possibility of large value GMD loss events, coupled with the continuing increase in mill size or required availability and reliability targets, could potentially lead to major conflicts as it becomes difficult for the insurance companies to judge the risk and hence may result in hesitation to insure these grinding circuits. This paper will not only describe the conflicting situation from both an insurer's perspective and from an equipment supplier's perspective, but also how these conflicting challenges can be successfully mastered. It has to be noted that not only the mining companies themselves, but also their insurance companies and the involved equipment suppliers have a common interest: to reach the highest availability and reliability in order to avoid or at least minimize unscheduled shut down times, and most importantly prevent unplanned events that result in extended production stoppages or reductions in through-put of GMD driven mills. From the very beginning onwards, the complete service concept together with emergency plans must be integrated on every level in the design of the grinding circuit. This approach must be implemented continuously and without compromises by all involved parties during all following stages, such as basic design, detail design, manufacturing, quality inspection and testing, packing, transportation, storage, installation, commissioning, operation and maintenance. The concept of formal risk analysis related to mill operations, maintenance and spare parts strategies must be an integral part of mining companies? decisions related to the selection for installation and continued use of large mills powered by GMDs. The service concept in place for operating mills shall also have a clear focus on very early detection of any abnormalities, so that the risk can be mitigated and unscheduled shutdown times avoided. However, if a major failure occurs, then procedures and tools shall already be available in order to ensure that production impact is minimized.

Jan 1, 2012

By J. M. Newell, G. R. Peatfield

"The Red-Chris porphyry Cu-Au deposit is located between Ealue and Kluea lakes, southeast of the village of Iskut on the Stewart Cassiar highway in northwestern British Columbia. It was explored by Texasgulf Inc., in a joint venture with Great Plains Development Company of Canada, Ltd. and Silver Standard Mines Ltd., during the period 1973 to 1980. Exploration resumed in 1994, following acquisition of the interests originally held by Texasgulf and Great Plains Development by American Bullion Minerals Ltd.Prospectors were first drawn to the area by prominent limonitic stain zones exposed in creek gullies in the western part of the property. These zones are developed on the alteration halo at the western periphery of the deposit. The potential ore zones do not crop out and were first exposed in a bulldozer trench excavated in 1971. Subsequent exploration was by percussion and diamond drilling, guided to some extent by induced polarization surveys. In 1976, estimated resources contained within two crudely designed open pits were 41 million tonnes with an average grade of 0.56% Cu and 0.34 g/t Au, with a cutoff grade of0.25% Cu. New resource estimates based on a major drilling program completed by American Bullion in 1994 were released as this paper goes to press. These estimates were calculated using various copper cutoff grades; at the 0.4% Cu cutoff, the ""in-situ geological reserve"" is given as 100 million tonnes grading 0.58% Cu and 0.46 g! t Au (American Bullion Minerals Ltd., 1995).The deposit consists mainly of pyrite, chalcopyrite and increasing bornite at depth, in zones of quartz-vein stockwork hosted by an elongate body of altered monzonite porphyry of latest Triassic or earliest Jurassic age. The stock intruded volcanic and sedimentary rocks of probable Stuhini Group affinity and is in faulted contact with sedimentary rocks of the Jurassic Bowser Lake Group. Gypsum stockworks are developed in the higher levels of the subvolcanic porphyry system. Late-stage quartz-carbonate veins carry small amounts of galena and sphalerite. Complex faulting within the deposit makes drill-hole correlations difficult. Alteration assemblages include an early potassic phase, almost completely destroyed by later phyllic alteration, and surrounded by a propylitic assemblage dominated by ankeritic carbonates in altered sedimentary rocks.The deposit has characteristics of bath the alkalic and calc-alkalic classes of porphyry copper deposits. The development of quartzvein stockwork suggests a calc-alkalic affinity, but the hostrocks contain little or no free quartz, molybdenum is present in trace amounts only and gold values are significant. Copper grades vary between wide extremes with unusually high grades in some sections of the deposit. The weight of evidence available in the 1970s led us to place the Red-Chris deposit firmly in the alkalic family. The quartz-sericite alteration assemblage was attributed to breakdown of potassium feldspar in a near-surface alteration environment in which seawater may have had a significant role. These interpretalions are retained here, but preliminary conclusions from the most recent work suggest that they may require some modification."

Jan 1, 1995

By C. E. White

History The Con-Rycon mine is situated in the Yellowknife mining district, North West Territories, 608 air miles north of Edmonton, Alberta. The earliest reported discovery of gold in the area was made in 1898 but no extensive exploration occurred until 1928. The birth of Yellowknife as a mining community took place in 1934 with the staking of the Rich group and subsequent shipping of 16 tons of high grade ore. The Giant group was also among the claims staked in 1934, and later staking showed a tendency to close the gap between these two properties. In the fall of 1935, the A.Y.E. claims, situated south of the Giant group, were staked to cover a discovery of the Geological Survey of Canada and, after general release of the Survey's information, the adjoining ground was staked. These claims included the Con, Negus, Meg, and Kam groups. In 1936 four lapsed claims were re-staked as the P and G group and later acquired by Rycon Mines, Limited, controlled by the Consolidated Mining and Smelting Company of Canada, Limited. The Con and various adjacent groups owned by Cominco are now operated with the Rycon under one management. Surface trenching on the Con property started in 1936 and, during the fall and winter of 1936-37, a 60- foot 5 ft. by 9 ft. inclined prospect shaft was sunk. The encouragement provided by the shaft and diamond drilling in 1937 led to the decision to establish a mining plant, and in August, 1938, the 100-ton cyanide mill produced its first brick- the first gold brick poured in the history of the North West Territories. In November, 1938, the mill was enlarged to a 175-ton capacity and operated at this rate until 1941, when refractory ore was encountered. This situation was met by the installation of flotation and roasting units and, at the same time, the milling capacity was increased to 300 tons daily. Labour shortages and Government restrictions forced a reduction of output and in 1943 milling was suspended while mine development continued on a reduced scale throughout the war years. The present full-scale of operations was resumed in 1946 and the total production to the end of 1948 amounted to 288,853 oz. gold and 72,347 oz. silver.

Jan 1, 1949

By G. Bridgstock, S. S. Forbes, E. M. Elkin

"OPERATIONS at Canadian Cop-per Refiners Limited, since the refinery was established in 1931, have been described in previous papers ( 1,2). Since then the refinery has treated the entire copper output of Noranda Mines Limited and Hudson Bay Mining & Smelting Company Limited. With the commencement of production in 1956 at Gaspe Copper Mines Limited, this copper has also been refined. From the start of operations to the end of 1958, the following had been refined: copper, silver, gold, selenium and tellurium.Construction of new buildings and additions to other buildings have been needed to handle increased receipts. The refining capacity has been increased from 112,000 tons of copper per year to a total of 236,000 tons per year.The refinery is located at Mont-real East, Quebec, close to railway and highway facilities. Incoming materials and shipments, with some small exceptions, are handled by rail. Some finished products are sl1ipped by industrial flatcar to the adjoining plants of Canada Wire & Cable Company Limited and Noranda Copper & Brass Limited."

Jan 1, 1960

By E. A. G. Colls

PART I.-GASES IN INDUSTRY INTRODUCTION THE part played by gases in industry can be considered from at least four distinct viewpoints, viz: (1) As air to support combustion and life and do various kinds of work (2) As fuel, or as essential to certain chemical processes (3) As sources of danger from explosion or fire ( 4) As hazards to man's health The present paper deals with gases only insofar as they are sources of danger, or are hazards to health. It may be noted, however, that, in point of tonnage, air is one of the most important materials handled in any industrial plant. In the operations of the Consolidated Mining and Smelting Company, for example, 138,000 tons of air are handled daily, the only material exceeding this figure being water. The United States Bureau of Mines has listed no fewer than seventy-four gases and vapours that, under certain conditions, may be considered as ex-plosive or dangerous (poisonous). The commonest and most important of these are as follows : Carbon monoxide Methane Acetylene Hydrogen Oxygen Hydrogen sulphide Benzol vapour Ammonia Petroleum vapour Carbon disulphide Hydrochloric acid gas Cyanogen Carbon oxysulphide Chlorine ` Fluorine (and fluorides) Acetone vapour Acetic acid vapour Water gas Natural gas Gasoline vapour Coal gas Producer gas Ether vapour Nitrogen oxides

Jan 1, 1940

By A. G. Roach

Introduction This paper deals with the operations and plant of the Craigmont Corundum Project, formerly of Wartime Metals Corporation but now under the Mines Section of the Resources Development Branch of the Department of Reconstruction and Supply. Corundum is recovered by the re-treatment of an old tailing deposit at Craigmont, Ontario. Crude concentrates so produced are shipped to the plant of the American Abrasives Company, Inc., at Westfield, Mass., for final processing and distribution to the abrasive industry. The plant was recently described in a paper entitled Craigmont Corundum which was presented by the writer before the Chicago meeting of the A.I .M.E. in February, 1946. General The Project is located on? lots 4 and 5, concession XVIII, township of Raglan, Renfrew county, Ontario, near the village of Combermere, which is on Highway 62. The property is about 135 miles from Ottawa. The general area enjoys a pleasant climate with moderate summer temperatures, though the winters are rather severe, the mercury frequently falling to - 35 deg. F. The excellent boating, fishing, and hunting have made the district a favourite resort for tourists. Lumbering is the main industry. Some farming is carried on, but the soil is poor and much of the land is hilly and rocky. There are no other operating mines in the immediate vicinity, though several 'industrial minerals', including mica, feldspar, nepheline, beryl, socialite, and others have been produced in the area. The district is drained by the York and Madawaska rivers and is generously dotted with large and small lakes. The general elevation is about 1,000 feet above sea level, though numerous hills rising several hundred feet give a rolling appearance to the landscape.

Jan 1, 1946

By C. S. Parsons

Introduction Up to the present, the operation of small mills for the treatment of gold ores has not been favoured in Canada to the extent that it has in other countries. For instance, a list of the operating properties in Southern Rhodesia, published in The Rhodesian Mining Journal of November, 1934, shows for the month of September, 1934, that there were over 500 small mills treating less than 50 tons per day, and the majority of these between 5 and 25 tons. They are operated by individuals, syndicates, and small mining companies. It is presumed that the operations are profitable, although from the published figures of the tonnages treated and the yields, it is difficult for one familiar with Canadian operations to understand how this can be possible, in the majority of cases. Most of these small mills employ stamps with plate amalgamation and with, occasionally, tables to produce a concentrate. Enquiries have been received from many parts of the world respecting milling practice suitable for small gold mines and the type of plant used in Canada. The tenor of these enquiries leaves the impression that the majority of the writers assume that the practice would be similar at all small properties. This, of course, is not the case. Conditions vary widely, and what would be a suitable mill for a typical Nova Scotia ore would not necessarily be wholly adaptable to many ores in Ontario, Quebec, or British Columbia. This paper has been written with the intention of inviting discussion, and it is hoped that, by such discussion, the subject will be more fully dealt with than has been possible in the time at the disposal of the writer. Only more or less standard principles and practices have been dealt with, and, purposely, no reference has been made to plants using mills of the Hadsel, the Nutt, or the Gibson type. As there is available but little reliable information on the costs of installation and operation of small mills, it is also hoped that those contributing to the discussion of milling practices for small mines will be in a position to give these data for the benefit of those contemplating the erection of small plants in Canada. Although it is difficult to generalize, it can be said that there are three types of gold mills commonly used at small mines: (1) Amalgamation and Gravity Concentration; (2) Amalgamation and Flotation; and (3) Cyanidation.

Jan 1, 1935

By J. P. Caulfield

THE Hudson Bay Mining and Smelting Company's underground mine at Flin Flon, Manitoba, has in the past been serviced by two working shafts-the North Main shaft, and the No. 3 shaft. The North Main shaft is used to hoist the total production from under-ground, and handles the greater part of the mine supplies and crews. The shaft is five-compartment design, rectangular in cross-section, and is equipped entirely with steel shaft sets from the surface to the finished depth of 2,210 feet. Hoisting equipment in the surface plant will not permit the North Main shaft to be extended below its present finished depth. The No. 3 shaft, located approximately 2,300 feet from the North Main shaft, is used primarily as a ventilation shaft, and for hoisting lower-level development waste to the 390 level, where this material is used as mine fill. The No. 3 shaft is of standard rectangular design, timbered with 8-in. by 8-in. creosoted fir sets, hung on 6-foot centres. From the surface to the 1,430 level, the No. 3 shaft consists of three 5 ft. by 5 ft. compartments, and below this level to the completed depth of 2,300 feet, the shaft is increased to four compartments. To service the mine and to expedite development below the 2,210 level, a one and one-half compartment winze was sunk from the 2,210 level to a depth of 766 feet, or approxima tel y the 3,000 level.

Jan 1, 1941

By S. Kwon, J. W. Wilson

"In salt and potash mines, the time-dependent deformation mechanism should be clearly understood based on in situ measurements to predict the performance of a mining design. In this study, in situ deformation measurements from the Waste Isolation Pilot Plant (WIPP) and other salt and potash mines were used to determine the transition time from the primary to the secondary creep stage and to investigate the influence of adjacent excavations such as a nearby tunnel excavation, panel excavation and/or pillar extraction on rock deformation. IntroductionThe deformational behaviour of underground excavations in salt and potash mines is complex due to the time-dependency of the rocks. When the material properties are determined from laboratory tests, they should be carefully applied to in situ conditions, because in situ conditions are completely different from laboratory conditions. For instance, in situ deformation measurements show that the deformation rate decreases with time similar to those observed in the laboratory during the early stages. However, the rapid decrease of deformation rate does not come from the microscopic strain hardening effect observed in laboratory tests, but mainly from stress relief around the opening after its excavation (Baar, 1977). It is, therefore, recommended to undertake in situ measurements and use them to understand the deformation mechanism.Even though in situ measurements are widely accepted as important information for understanding the deformation mechanism of salt and potash (Barr, 1971; Kovari and Amstad, 1993), not many publications have focused on the fundamentals of data measurement, the application of the measured data, and the development of data analysis techniques. Recently, several new techniques for better understanding the deformation mechanism of rock salt have been developed that are based on in situ measurements. Kwon and Miller (1995) developed a new technique for describing the actual deformational behaviour of an underground excavation in rock salt. The migration of “zero strain boundary,” which represents a no movement boundary around an underground excavation, could be calculated by the technique developed by Kwon and Miller (1996). Kwon and Wilson (1997, 1998) applied neural network techniques to in situ deformation measurements to predict the deformational behaviour of the underground excavations at the Waste Isolation Pilot Plant (WIPP) located in the United States.In this study, in situ deformation measurementsfrom the WIPP site and other salt and potash mines in the United States were extensively analyzed to understand the deformation mechanism of the underground excavations in the rock mass."

Jan 1, 2002

By J. G. A. Stevenson

"IntroductionDURING the past quarter of a century diamond drilling, in all its phases, has increased in Canada to a very impressive total of more than 10,000,000 feet annually. Since the art of diamond drilling became recognized, some seventy-five years ago, there has been considerable improvement in both equipment and technique. The steam-powered drill rig and the hand-set diamond bit are things of the past.The purpose of this paper is to review some drilling trends •and practices over the past few years. In the preparation of the paper, the author wishes to acknowledge kind assistance of Mr. J. D. Cumming, Dr. C. H. Hitchcock, Mr. Robert H. Quintal, and many others, including staff members of the Longyear organization.Figures provided by the Dominion Bureau of Statistics for the year 1954 show that Canadian production of metallic and non-metallic minerals and structural materials had a value of $1,454.2 million, excluding radioactive products for which figures are not available. Approximately 61 per cent of this valuation comprised production of nickel, copper, gold, coal, asbestos, zinc, lead, and iron. It is certain that diamond drilling played a major role in the discovery and development of the orebodies from which these minerals were obtained.After the surface examination of an ore deposit, diamond drilling will automatically follow, in order to determine structure, grade, and tonnage.Footage drilled by mining companies and contractors on mineral exploration and blast-hole work since 1945, as reported by the Do-minion Bureau of Statistics, is shown in Figure 1."

Jan 1, 1955

By Ernest Davis

WATER power, until developed, produces nothing, but when harnessed it continues to produce, it might be said, indefinitely. Hence the importance of developing all feasible water powers. British Columbia, like the western states of America, is subject to variable meteorological conditions which cause most streams to be erratic in their flow. The wet season, usually commencing in October and continuing to March or April, together with the melting of the snows during the early summer, produces a heavy run-off which diminishes considerably during the later s1.1,mmer months, with the result that storage is essential on practically every stream in order to regulate the flow to obtain a discharge which will meet the requirements of the load of the markets the power is to serve. Storage sites of sufficient capacity to equate the flows are not always present and it follows that, where such a deficiency exists, the difference must usually be met by burning fuel in steam plants. Fortunately, there are within the Province deposits of high-grade coal, suitable for the operation of such auxiliary steam plants. One of the strongest reasons for the development of water powers is the conservation of fuel. All use of coal or oil depletes resources that can never be renewed. Every water power developed means a saving in fuel and, even if at first it does not possess an over-powering financial advantage, it must become of ever increasing value as fuel resources become depleted. However, sight must not be lost of the inter-relation which should exist between the two methods of generating electrical energy, as each makes an admirable supplement to the? other with respect to suitability for carrying different types of load. In general, it can be said that the fixed charges of a water power development are usually high in relation to the operation costs, while those of fuel power plants are usually the reverse, so it is sometimes possible to combine the two methods of generation for the more efficient production of energy.

Jan 1, 1942

By G. Auld

"A simple method is presented whereby the additional quantity and static pressure necessary to compensate for ventilation duct leakage may be estimated using the circular reference functions of modern spreadsheets. Favourable comparisons have been made to the National Coal Board (United Kingdom) design charts and to a case study analysis. IntroductionIn mining, most ducted systems are applied to the development of access tunnels, and most of these systems leak to some extent. When the ventilation duct fails to deliver the required quantity of air to the work place, there is a significant contribution to the development costs, either directly or indirectly.Directly — More air and more pressure are required to compensate for the leakage, more capital development (ventilation shafts, parallel drives) are required because ventilation systems cannot push the fresh air far enough, and longer re-entry times to ensure toxic blast fumes to be diluted.Indirectly — There is a reduction in productivity because of the inclement atmospheric conditions, and/or closure of development ends because of unacceptable atmospheric conditions at the working place. This has been exacerbated over the last few decades because of the increased use of diesel equipment of ever increasing power, and the more stringent Occupational Health and Safety requirements demanding more air flow per kilowatt of diesel power.The leakage from a duct must, therefore, be reliably estimated in order to assess the effectiveness and construction of the system; assess the effectiveness of the maintenance or repair of the duct; appreciate the cost of the leakage, and therefore apply effective maintenance and installation procedures; and engineer safer, healthier and more cost-effective ventilation systems."

Jan 1, 2002

By G. W. Adams

Foreword While the literature on radium is voluminous, there is no single publication available from Canadian sources which attempts to cover at all fully the world radium industry. The comparatively recent developments in the Wilberforce area, and the consequent arousal of public interest in radium, seemed to call for the publication of such a paper which would be intelligible to the layman. To satisfy this apparent need, the writers submit this paper which contains material derived from various sources, and for which the writers make no claim of originality. Direct references are made throughout the paper to sources of information.

Jan 1, 1931

By Toshiharu Teranishi

When we apply the Au nanoparticle superlattices to the future nanooptical and nanoelectronic devices, the control of not only the particle size but also the interparticle spacing and symmetry of superlattice are the essential problems to be overcome. First, we developed a novel synthetic procedure to precisely control the particle size of alkanethiol-protected Au nanoparticles in the range from 1.5 to 9.7 nm by the heat-treatment of the small Au nanoparticles in the solid state. Absorption and nonlinear optical properties of alkanethiol-protected Au nanoparticle superlattices were then elucidated. On the other hand, the hexagonal close-packed (hcp) 2D superlattices of small Au nanoparticles with the interparticle spacings from 1.9 to 3.6 nm were successfully prepared by using newly-synthesized ligand for single electron tunneling devices. Finally, various symmetric superlattices, such as chain (2-fold), quasi-honeycomb (3-fold), square (4-fold), etc., of Au nanoparticles could be produced by making use of interligand interactions or some templates.

Oct 1, 2003

By Lian-Jin Tao

With fast development of China modernization, road construction obtains great achievement. However, in the construction process of highway, especially the high-grade highway in mountainous area, there are many unavoidable high cut slopes. Specifications for Design of Highway Subgrades, China, prescribe that the design scheme of slope with height more than 30m should be compared with bridge scheme and tunnel scheme economically. In spite of the existing guidelines, it is still quite common to see many high slopes due to engineering geological conditions, highway line shape, cost and issues related to traditional design ideas. Actually the traditional way with ?high backfill, the high cut? for mountainous highways seriously damages the original ecological environment and groundwater system, especially to those area with weak ecology, where the damage is unrecoverable. It is quite common practice to use artificial vegetation for cut slope virescence, however it still has problems such as low ratio of survivor, high maintenance cost and lack of species diversity. Now people are more and more aware of the importance of ecological environment, it becomes urgent to decrease the damage to ecological environment after ensuring the stability of high slopes. With the aim to reduce ecological damage, we proposed a new design approach which is ecological environment friendly by decreasing cut slope height with steep excavation scheme. This approach requires that (1) the geological condition is good, and the rockmass can be sTable itself; (2) excavation should not badly damage the rock, which means blasting must be controled by using buffer blasting, smooth blasting and pre-splitting blasting; (3) if local geological condition is not very good, excavation should have intervals for one bench, the advised space is 20m; (4) to ensure the slope stability in construction process, the cut slope should be reinforced more strongly than usual and in time. Finally, the deformation of the slope and the working condition of the reinforcement structure should be monitored to ensure the slope stability. The new design is used to a roadside cut slope of provincial trunk highway S223 in Guangdong Province. Based on intensive geological investigation and borehole tests, it is found that the slope rock mass is intact and sound, and the rock strength is quite high. Results from numerical modeling by UDEC reveal that compared with the traditional design scheme with 90.23m high slope, the steep scheme with only 23.46m high is characterized by its relatively large deformation and stress concentration, however the influenced area only appears at the upper slope and tends to sTable. With cable reinforcement, the stability of slope excavated steeply can be guaranteed. Deformation of the slope and the cable force are monitored in details in the period of construction, which show that the deformation of the slope decreases gradually and the final deformation is very small, and the cable tensions change small after the cables were tensioned. It is optimistically estimated that the steep slope should be sTable during operation. Comparison analysis between the steep scheme and the common scheme affirms that the steep excavation is better than the traditional scheme in terms of ecological environmental effect, slope height, the excavated amount, the excavated quantity of slope surface, engineering cost. It is concluded that if geological condition permits, the steep cut scheme should be used with better benefits.

May 1, 2009

By R. G. K. Morrison

By arrangement between the Ontario Mining Association and Messrs. John Taylor & Sons, Mining Engineers, 6 Queen Street Place, London, E.C.4, the writer was engaged for a period of not more than three months to report on the rockburst situation in Ontario mines. This was later amplified, by mutual agreement, to include, at the expense of detail, visits to the larger camps where rockbursts had not occurred, to get a general picture of conditions and to discuss the subject with operators in their respective areas. Scope of Activities Visits were paid to the following properties for the purpose of enquiry and discussion; the underground workings of those mines marked with an asterisk were visited on one or more occasions: KIRKLAND LAKE * Macassa Mines, Limited * Kirkland Lake Gold Mining Co., Ltd. * Teck-Hughes Gold Mines, Limited * Lake Shore Mines, Limited * Wright-Hargreaves Mines, Limited Sylvanite Gold Mines, Limited Toburn Gold Mines, Limited EAST KIRKLAND & LARDER LAKE Upper Canada Mines, Limited Chesterville Larder Lake Gold Mtng Co., Ltd. Kerr-Addison Gold Mines, Limited Omega Gold Mines, Limited PORCUPINE * Hollinger Consolidated Gold Mines, Ltd. * Mcintyre Porcupine Mines, Limited * Dome Mines, Limited * Buffalo Ankerite Gold Mines, Limited Paymaster Consolidated Mines, Limited Preston East Dome Mines, Limited Pamour Porcupine Mines, Limited Broulan Porcupine Mines, Limited Hallnor Mines, Limited Naybob Gold Mines, Limited Delnite Mines, Limited Moneta Porcupine Mines, Limited DeSantis Porcupine Mines, Limited Coniaurum Mines, Limited SUDURY lnternational Nickel Co. of Can., Ltd. * Falconbridge Nickel Mines, Limited LITTLE LONG LAC AREA * Little Long Lac Gold Mines, Limited MacLeod-Cockshutt Gold Mines, Ltd. Hard Rock Gold Mines, Limited Bankfield Consolidated Mines, Limited Magnet Consolidated Mines (1936), Ltd. à PICKLE LAKE AREA * Central Patricia Gold Mines, Limited * Pickle Crow Gold Mines, Limited UCHI LAKE * Uchi Gold Mines, Limited McKENZIE ISLAND AREA Gold Eagle Gold Mines, Limited * McKenzie Red Lake Gold Mines, Ltd. * Cochenour Willans Gold Mines, Limited RED LAKE * Howey Gold Mines, Limited Hasaga Gold Mines, Limited Madson Red Lake Gold Mines, Limited

Jan 1, 1942

By C. L. Reichardt

"Pressure exerted on gold producers by regulators, project financiers, and civil society in the wake of the Baia Mare tailings spill in Romania during 2000 prompted most responsible gold companies to sign up to the International Cyanide Management Code for the Manufacture, Transport, and Use of Cyanide in the Production of Gold (the Code). The Code stipulates a ‘cradle to grave’ approach more comprehensive than that applied to any other mining reagent and poses particular challenges for operators who use cyanide-bearing tailings for backfill. This paper examine some of the challenges for Code compliance facing deep underground gold mines that employ backfill technology, most particularly the requirement to demonstrate that the potential migration of cyanide (and its degradation products) from emplaced backfill will not have an unacceptable impact on worker health and safety or on the receiving environment, either during mine life or after closure.Although the Code only contains a single reference to backfill, more careful consideration confirms that most sections of the Code that deal with tailings management are potentially applicable to mines where tailings material is used for backfill. Certain principles of the Code also pertain to aspects of operations, worker safety, emergency response, training, and dialogue with stakeholders relating to backfilling practice.For gold mines of the Far West Rand, the most significant cyanide-related risks associated with backfill operations relate to worker exposure to cyanide-bearing seepage and HCN gas. There is potential for seepage of cyanide-bearing water from backfill to compromise the beneficial use of surface and groundwater, and thus impact on downstream users and ecosystems. However, the extreme depth of mining and the specific geological and hydrological controls on the Far West Rand suggest that the potential environmental risks associated with backfill are likely to be considerably less significant than the cyanide-related risks to the workforce."

Jan 1, 2007