Search Documents

By Eugene F. Casey, John G. Ruggiero

INTRODUCTION Construction of tunnels in urban areas, especially reclaimed areas, pose many problems. The Red Hook Intercepting Sewer Tunnel, Contract 1A is a portion of the Red Hook Water Pollution Control Project located along the Brooklyn waterfront in New York City. This contract required the construction of a 2620 meter long (8600 L.F.), 3 meter (10-foot) diameter soft ground tunnel, eight Tunnel Manholes, nine Regulator structures, four Diversion and Tidegate structures and 765 meters (2500 L.F.) of branch intercepting sewers of diameters between .30 meters (12 inches) and 1.8 meters (72 inches). The construction contract bid price was $62 million with a duration of three years. The tunnel route crosses over five sets of operational twin cast iron subway tubes with clearances ranging from 4.3 meters (14 feet) to as small as 0.35 meters (14 inches). The route of the tunnel traverses historically interesting areas which have been reclaimed over the last 200 years. This paper is a case history describing the contractor's methods utilized to successfully advance the work through the above problem areas. LOCATION The Red Hook Intercepting Sewer Tunnel is located in the Borough of Brooklyn of New York City. The route is

Jan 1, 1981

By C. John Dunnicliff, Birger Schmidt

INTRODUCTION To be effective and useful, monitoring of tunnel construction must be carefully planned throughout all steps. A vital and frequently overlooked step is a clear definition of the specific purposes of the instrumentation. Most tunnel construction monitoring has in the past been of benefit to research, the advancement of tunneling practice, wittingly or not. The development of monitoring instrumentation for the benefit of the project from which the data are recovered has very significant potential for risk and cost reduction of soft ground tunneling. A systematic approach to tunnel construction monitoring, from conception to full implementation, includes at least the following nine tasks or steps: Definition of benefits and purposes; design and project specification to draw full benefits; selection of monitoring parameters; selection of instruments and writing of specifications for procurement and installation; procurement and installation; reading and maintenance; data storage and retrieval; interpretation; implementation. Some of these steps are fairly easy and resolved through the use of established theories and technologies. The difficult ones are those that require the bending of minds, those that involve changes in the ways engineers design soft ground tunnels, the way owners pay for tunnels, and the construction is managed, inspected and controlled. Performance monitoring can be of benefit to the owner, design

Jan 1, 1974

By Jon Y. Kaneshiro, Stephen J. Navin, Jerry Ostberg

In 1968, the U.S. Bureau of Reclamation awarded S.S. Mullen Construction of Seattle, the Intake Tunnel (488 m by 4 m diameter tunnel) and Pumping Plant No. 1. In1998, the Southern Nevada Water Authority awarded Lake Mead Constructors (Kiewit of Omaha) a parallel New Intake Tunnel (518 m long by 4.6 m diameter tunnel) and Pumping Plant. Both projects provide water to a thirsty Las Vegas. This paper presents a detailed comparison of the two intake tunnels in terms of grout takes and pressures, geologic mapping and rock quality, grout penetration beyond the excavation line, degree of fracture grouting, and groundwater inflow boundary considerations. The paper provides a comparison of grouting techniques and material developments then and now.

Jan 1, 2001

By R. Switalski, M. Schafer, R. Pintabona, M. Kritzer, B. Lukajic, S. Janosko

Methane gas caused an eight-month shutdown of mining operations at the Mill Creek, Phase 3, Tunnel. The gas-related shutdown occurred as the tunnel was advanced to an approximate distance of 2,700 feet, which constitutes approximately18% of the total tunnel length. The construction of an emergency ventilation shaft, a comprehensive program of de-gassing wells and an expanded gas monitoring system were used to mitigate the gas condition. When complete, this tunnel will be utilized to convey and store combined storm and sanitary sewage collected from a portion of Cleveland, Ohio and ten suburbs. This paper will provide an overview of gas related remedial measures and explain how these measures were integrated into the project to ensure safe tunneling conditions.

Jan 1, 2007

By Wern-ping (Nick) Chen

In concrete lined tunnels, formwork removal timing may be controversial. Contractors seek to strip the form as soon as possible, and designers seek to keep the formwork in place as long as practical to protect the fresh concrete. Formwork removal timing is normally specified as a function to its insitu concrete strength. This approach may work for smaller diameter tunnels, but fallacy occurs when applying this approach to larger diameter tunnels, since a larger diameter would experience more displacement than a smaller diameter tunnel from its own weight. Excessive deformation may fail a tunnel to meet its roundness criterion and overstress the lining causing cracking or falling from the crown. This paper presents a contractual mechanism to mitigate this issue.

Jan 1, 2008

By David Jurich, Joseph N. McDivitt

INTRODUCTION South Coast Water District (SCWD) operates the Beach Interceptor Sewer Tunnel(BIST) in South Laguna, Orange County, California between Monarch Beach and Aliso Beach (Figure 1). The 10,200-foot long BIST houses a 24-inch gravity Techite sewer pipeline critical to the SCWD Sanitary Sewer Collection System. The original tunnel and sewer pipeline were constructed in 1954 and the sewer line was replaced in 1974.Periodic inspections by sewer pipeline maintenance crews documented deterioration of specific intervals of the tunnel. Rotting timber supports and rock falls in the tunnel as a result of the deterioration were endangering the sewer pipeline and a 731-foot section of tunnel located at Thousand Steps Beach was determined to be in immediate need of repairs. SCWD and consultants Hatch Mott MacDonald (HMM) and Tetra Tec prepared a Work Plan for emergency tunnel stabilization and pipe protection measures that was implemented in January 2007. Normal access to the beach and the section of tunnel requiring repairs was limited to public stairs referred to as Thousand Steps and, therefore, all materials and equipment needed for the work were transported to the beach by ocean-going landing craft. Additionally, the emergency repairs had to be completed without taking the pipeline out of service. Numerous environmental, logistical and operational requirements had to be overcome to complete the challenging emergency repairs. GEOLOGICAL SETTING The Laguna Beach area is located in the Peninsular Ranges of Southern California. The project area is located on the southwest flank of Niguel Hill along marine wave-cut cliffs and slopes. The tunnel was excavated in the San Onofre Formation, a marine deposit, characterized by abrupt lateral and vertical changes in lithologies that vary from boulder to cobble and gravel size breccias to medium coarse sandstones with gravel, sandy claystone and siltstone. The interval of the tunnel that required repairs is located within the San Onofre breccia, a moderately-to-well cemented, poorly bedded to massive unit with angular to subangular boulder and cobble sized clasts of schist. The sandy silt matrix of the breccia is composed of quartz, feldspar and schist grains (Figure 2). GENERAL TUNNEL DESCRIPTION The approximately 6-feet high by 6-feet wide 10,200-foot-long BIST was hand mined in 1954 at the base of the coastal cliffs. Primary access is through twenty-one access adits from public and private beaches. The tunnel is located in an easement that extends beneath private property with residential structures situated 50 to 80 feet above and horizontally in close proximity to the tunnel alignment. Most of the tunnel is horse-shoe shaped and unsupported, but approximately 3,000 feet is supported by timber

Jan 1, 2007

By H. S. Rathor

NTPC (National Thermal Power Corporation), a multi-unit organization, is generating 26% of India’s total power. This power is produced from its 14 coal based stations and 7 gas based stations. NTPC is entering into the business of power-distribution, power-trading, setting up of coal mines and diversification in non-conventional energy sector as well. For achieving the goal of the country “Power for All” NTPC has taken a giant stride by entering into Hydro Power generation which is also the cheapest and the cleanest renewable source of energy. In its pursuit for excellence, 800 MW Koldam Hydro Power Project is NTPC’s first venture in hydro sector. In Koldam, hydropower potential will be harnessed by constructing a 163m high earth and rock fill dam in a narrow gorge at upstream end of Bhakra reservoir. The river diversion is envisaged through two parallel, 14m finished diameter ‘horseshoe’ tunnels of length 901m and 934m at village Kian on the right bank, where the river forms a 180° loop. The diversion tunnels are designed to accommodate a flood of 6500m3/sec, taking into account the maximum probable discharge of 200 years return period. The tunnels pass through dolomite and limestone rock formations. The excavation of tunnels was done with drill and blast method. The excavation was attempted from both inlet and outlet faces. During geological investigation a rock fault was located at the outlet area. The location of the fault was such that it was passing through the edge of the Tunnel-1portal and around 30m away from the face of the Tunnel-2 portal. The quality of the rock at Inlet was also poor. To save the portals from slips, excavation of the tunnels was planned to start after the completion of the open excavation and its support system both at inlet and outlet. The tunnel excavation at inlet was envisaged by approaching the tunnels’ portal by constructing a road through 540EL bench and meeting the inlet portals on the upstream end, which would have been ready by mid2003, only after completion of the open excavation and its support system. To save time and cost, it was felt necessary to modify the planning by starting the tunnel excavation simultaneously along with open works both at inlet and outlet. The excavation at the inlet face of the tunnels started in December 2002 after rerouting the approach road to inlet portals through haulage road on the downstream and similarly Tunnel-1 at the outlet was started in the low cover area before completion of open area works. Thus the tunnel—heading excavation was started nearly 06 months early with the change of methodology.

Jan 1, 2005

By Albert Ruiz

South Coast Water District (District) operates the Beach Interceptor Sewer Tunnel (BIST) in South Laguna, Orange County, California between Mon-arch Beach and Aliso Beach (Figure 1). The 10,424-foot long BIST houses a 24-inch Techite gravity sewer pipeline critical to the District Sanitary Sewer Collection System that conveys 1 MGD of raw sewage to a wastewater treatment plant. The original tunnel was constructed in 1954 and the sewer line replaced in 1974. Periodic inspections by sewer pipeline maintenance crews have documented deterioration of specific intervals of the tunnel within the past few years (Sancon 2003). Rotting timber supports and rock falls in the tunnel as a result of the deterioration were endangering the sewer pipeline. A 50-foot section of the tunnel was determined to be in need of immediate repairs, which were carried out from January to August in 2007. This section was enlarged to a horseshoe shape and lined with shotcrete. The pipe was encased in concrete in the invert of the new enlarged cross section. Hatch Mott Mac-Donald (HMM) designed the emergency repairs, carried out an assessment of the rest of the tunnel alignment, and is currently developing a work plan for rehabilitating the entire tunnel.

Jan 1, 2008

By D. Caiden, C. S. Covil, P. J. Chamley

The paper describes the background to alternative delivery models, drawing on international experience, and introduces Project Alliancing/Contract Partnering, common risks and risk sharing on tunnel projects. A plea for early contractor involvement in design is made before describing some whole life design implications for tunnels. The paper concludes with four short case studies; Channel Tunnel Rail Link in the UK, Hull Waste Water Tunnel in the UK; Island West Sewage Transfer Station in Hong Kong, and the New Southern Railway in Australia.

Jan 1, 2005

By Remo Grandori, Manfred Jaeger, Fabrizio Antonini, Luis Vigl

The EVINOS-MORNOS tunnel project with its 30 km of length is one of the longest hydraulic tunnel in the world realised with TBM method. The adverse geological conditions, the high cover and the short construction schedule were a great challenge for the successful construction of this tunnel. The paper will describe: the criteria adopted for the tunnel design, the selection of the construction methods and equipment, the productions of the 4 TBMs adopted and the comparison of the behaviour of the different type of TBMs in the various rock conditions, including special conditions, the characteristics of the adopted in situ and precast linings, a comparison between the foreseen and actual construction schedules, the contractual implications of realising a tunnel in such a severe and complex conditions.

Jan 1, 1995

By Roberto J. Guardia, Tim Shell, Robert A. Robinson, Steve Rodolf

Our aging infrastructure includes numerous tunnels that provide easy access through topographic and societal obstacles. These tunnels are renewable resources that require periodic maintenance and rehabilitation to extend their useful lifespan to hundreds or even thousands of years. However, as with any structural rehabilitation project, tunnel liner rehabilitation requires an inordinate amount of evaluation and care due often poorly documented original construction and subsequent repair construction methods and materials. This paper documents the investigation, planning, design, and construction efforts of the rehabilitation of a 74-year old, 216-meter (713 foot) long two-lane highway tunnel in moderately fractured to highly sheared basalt on the Oregon coast. The tunnel consists of four sections lined originally with timber and subsequently overlaid with concrete, and three unlined sections.

Jan 1, 2005

By David Smith

Construction of a new transportation link frequently requires crossing under an existing highway or railroad. Although traffic diversions may permit a cut and cover structure to be built, ‘zero impact’ tunnel solutions are becoming increasingly popular. The vertical clearance between the new tunnel structure and the existing highway or tracks may be very low; sometimes less than two meters. This leaves little room for error since any ground loss can rapidly translate into surface settlement. Problems can be avoided by maintaining the stability of the tunnel face and by minimizing ground movement around the tunnel lining. This paper examines construction methods that have been used to construct short tunnels with shallow cover, and highlights factors to be considered for future projects.

Jan 1, 2005

By Ergin Arioglu, Werner Burger

"SUMMARY The Istanbul Strait Road Crossing Project includes a 3.34 kilometer subsea tunnel excavated by TBM with an excavation diameter of 13.71 m. The tunnel will incorporate two road decks, each employing two traffic lines and shoulder with the daily capacity of 100,000 light vehicles. The tunnel alignment crosses full face rock sections with heavily fractured zones due to tectonic events as well as a long central stretch of difficult mixed face and very variable soft ground conditions. The demanding ground conditions and the large diameter in combination with realized face pressures well above 10 bar required a highly specialized and well adapted TBM. The paper describes the project challenges and the related technical solutions incorporated within the TBM design as well as the real site experience. INTRODUCTION In 2013, a 13.71 m diameter Mixshield was manufactured in Germany for the Istanbul Strait Road Crossing Project. The delivery of the TBM in late 2013 was a major milestone for the Istanbul Strait Road Crossing Project, also known as the Eurasia Tunnel Project. The Eurasia Project (www.avrasyatuneli.com.tr/en) consists of a 14.6 km route including a 5.4 km tunnel segment in its central part crossing the Bosphorus. The 3.34 km subsea section of the tunnel was excavated in closed mode using a Mixshield TBM. The remaining tunnel length is constructed by sprayed concrete lining (SCL) method followed by a cast in place (CIP) lining or by cut and cover (CC) structures for the TBM transition boxes (Figure 1, right). Other project sections on the European and Asian side consist of upgrading and widening surface access roads towards the tunnel. Conceptual ideas of connecting Asia with Europe via a tunnel crossing the Bosphorus have been around for an extended time and only became realistic towards the end of the 20th century based on significant technical developments in mechanized tunneling. Feasibility studies for a new Bosphorus crossing in 2003 and 2005 confirmed and suggested a road tunnel in its present alignment as the preferred solution. Following an international tender process the Ministry of Transport, Maritime Affairs and Communications of Turkey assigned ATAS, a special purpose company formed by Yapi Merkezi (Turkey) and SK E&C (South Korea), to design, build and operate the Eurasia Tunnel Project. The Implementation Contract was signed in February 2011. In 2012, Herrenknecht AG was selected as the supplier for the 13.71 m Mixshield TBM."

Jan 1, 2016

By Karel Rössler, Petr Vítek

"The Ejpovice tunnels in Czech Republic were built by EPBM in soft Clyashale, and in weathered profile with low soil overburden. The segmented liner at the cross-passage openings required support, which would not interfere with the EPBM clearance envelope during the scheduled pull back of the EPBM through both tunnel tubes. For that reason support frames or radial bolting could not be used. Steel rods inserted into the neighboring segments during the ring assembly, and later grouted were tested and realized as an innovative solution. The paper presents practical experience gained with the segmented liner support during cross-passages construction. INTRODUCTION An innovative solution using the grouted dowels was developed and realized for sixteen cross-passage openings of the twin Ejpovice Tunnels, whose construction was part of the railway track Rokycany – Plzen modernization. The following paper described practical experience gained with the innovative support of cross-passage openings, which was realized by short steel dowels grouted within the segments of the EPBM segmented liner. The paper is a continuation of the paper published in WTC 2015, which described the design aspects of the grouted dowels support, while the following paper concentrated on the production, and the performance of the dowel support observed during the breakout for the cross-passages openings. The connection by grouted dowels was patented by Metrostav, a.s. Company THE EJPOVICE TUNNELS CONSTRUCTION The Ejpovice tunnels construction started in 2013. The start of the high speed train operation through the tunnels was planned for 2018. The project was funded by the state government with the support of European Union funds of up to 70%.The tunnels were excavated with one EPBM (Earth Pressure Balanced Machine) with the external diameter of 9.89 m. The segmental liner inner diameter was 8.7 m, and thickness of 0.4 m. First, the South tunnel tube was excavated from the East portal, then the EPBM was pulled back through the South tunnel, and the excavation was started from the same portal for the North tube. After the South tube was freed from the EPBM excavation operations the cross-passage construction started. Due to the short time schedule, in the North tube the cross-passage construction started while the tunnel was still under construction. Therefore, the cross-passage construction was performed concurrently with the segments transportation, and with the EPBM pull-back through the tunnel. There were 8 cross-passages along the tunnels with a maximum distance of about 500 m, Fig.1."

Jan 1, 2016

By Michael Gay

Right in the heart of Boston Harbor lies Deer Island, where a ten-year, 6 billion dollar sewage treatment plant is under construction. The 9.5 mile long, 25.5' diameter Effluent Outfall Tunnel is the center piece of this program. A Robbins double-shielded TBM is currently driving this challenging tunnel some 400 feet below sea level. This paper will discuss the set-up and operation of this Tunnel Boring Machine in driving the longest single heading tunnel ever built in North America.

Jan 1, 1993

By John H. Raymer

Groundwater inflow into hard rock tunnels is strongly affected by recharge and drawdown of the water table. Previous analytical and empirical methods for estimating inflow have generally not accounted for these factors in an accurate or systematic way, resulting is wrong conclusions about inflow and the effects of the tunnel on the surrounding environment. This paper discusses these issues and provides some simple analytical equations to estimate inflow and water table drawdown around the tunnel. Examples from tunnels in the Atlanta area are provided.

Jan 1, 2005

By James W. Martin, Robert R. Faddick

INTRODUCTION Virtually every sector of society in our country feels the impact of tunnels, either through the transportation of water, commodities, or people. The economic implications are staggering. The Committee on Rapid Excavation (1) reported that during the near future, 1968-1975, underground excavation activity will comprise 946 miles of tunnels (subways: 85 miles; underground urban highways: 123 miles; intercity highway tunnels: 210 miles; water supply tunnels: 528 miles) and 5,119 million tons of crude ore; metals: 874 million tons; nonmetals: 899 million tons; and coal: 3,346 million tons. It is estimated that the cumulative demand for underground excavation in the decade 1970-1979 will be 13 billion dollars for construction-oriented demand and 16 billion dollars for mining-oriented demand. The respective figures for the decade 1980-1989 are estimated at 22 billion dollars and 18 billion dollars. Of the many advantages claimed for tunnels (2, 3, 4, 5) the environmental considerations are becoming increasingly important. Transportation tunnels particularly for rapid transit systems, offer reductions in noise pollution and air pollution while improving aesthetics and optimizing land use (fewer problems of right-of-way and disruption of utilities). Considerable interest has been shown recently in sub-surface construction and mining (6, 7, 8). Recognizing the future demands for tunnels has led to considerable study of methods to improve rates of tunnel advance per day, safety, and the overall economics. The search for higher rates of advance has Led away from what has heap termed conventional methods (drilling

Jan 1, 1974

By Thomas Pea, Heiner Kontrus, Jérôme Steinkühler

In tunnel condition assessment, the trend is towards comprehensive 3D measurement combined with high quality image texture to document and quantify damages to the tunnel surface and to create a cohesive data base of the structural conditions throughout its lifespan. The faster such measurements can be made on site, the less it impacts traffic conditions of the highly sophisticated subway systems. The Dibit high-speed 3D scanning system which is based on Photogrammetry and LiDAR technology enables data acquisition in tunnels at a speed of up to 60 mph. Given the high rate of speed the system can operate, tunnel shutdowns can be drastically reduced, and tunnel safety increased. The photorealistic texturing of the 3D-model allows the identification and analysis of smallest material damage (e.g., cracks ≥0.3 mm wide). The publication illustrates technical details and 3D results of the innovative system from measurements that were performed in the subway tunnels of the Bay Area Rapid Transit System in San Francisco, CA (total length 66.23 km).

Jun 13, 2021

By Todd S. Webster, Matthew J. Pierce, Brad D. Krumel

With the Working Shafts and Starter Tunnel under way, it became apparent this 4.7-mile, 19-foot diameter wet weather tunnel was going to live up to its name. The shaft’s pre-excavation grouting was completed, and ground water inflows were slowing project progress. As the tunnel drive was approaching 50% complete a cooperative effort was underway between the owner, engineer, and contractor to raise the base of the Retrieval Shaft by 65 feet to avoid ground water infiltration construction challenges. The tunnel alignment needed to be raised in kind. The project was behind schedule and rethinking the cast-in-place adit work was next on the agenda due to the very wet environment in the tunnel. The race was on to finish the project within the owner’s time constraints while completing multiple redesign aspects of the tunnel alignment and associated adit construction. This paper will evaluate original design criteria and actual in-route design modifications and change management to meet the owner’s just-in-time schedule needs.

Dec 1, 2022

By Leonhard Schmid

INTRODUCTION In the region of Zurich several of the Swiss Interstate Highways meet and have to be linked to form a continuous network. The subalpine glacial topography with hills, ridges and lakes requires the construction of many tunnels (Figure 1). The Milchbuck Tunnel forms part of the inner arterial highway system of the city of Zurich. It passes underneath the ridge separating the Limmat and Glatt valleys. In its final configuration the tunnel will consist of two parallel three-lane tunnels (Figure 2). For the time being only one tunnel is constructed. This tunnel will be operated with two outbound (climbing) lanes and a single inbound (descending) lane (Figure 3). The owner, the Canton of Zurich, awarded the contract for the construction to a joint venture with the following three contractors: Locher & Cie AG (leader), Prader AG, A. Brunner's Erben, all located in Zurich. The actual freezing was performed by subcontractor Philipp Holzmann AG, Mannheim, West Germany. Electrowatt Engineering Services Ltd, Zurich, was design engineer and performed the construction supervision.

Jan 1, 1981