Search Documents

By Eugene L. Foster, Gilbert L. Butler

The successful demonstration of a precast segmented concrete liner in the Lexington Market Section of the Baltimore Regional Rapid Transit System (BRRTS) is an important step forward in our continuing efforts to control tunneling costs in the USA. In addition to its contribution to specific savings in future tunnels, this demonstration project has taught other lessons about the U.S. tunneling industry and about the process of "mainlining" new and improved technology into that industry. This paper will present an overview of the Lexington Market Demonstration Project from its beginnings to the present time. In addition, it will discuss other implications which have an important bearing on the extent to which tunnels will be used in future transportation systems in the USA. THE HISTORY Precast segmented concrete tunnel liners are not new. An unbolted version was reportedly used in New York City in the 1930's. The modern bolted configuration has been in use in foreign countries for more than 15 years. Indeed, consideration of the use of precast bolted segments below the water table in the USA dates back to the BART system in San Francisco in the 1960's. At that time, they were evaluated and it was concluded that the state of the art would not allow segments to be precast to the required tolerances. A secondary grinding operation would be required if water-tightness was to be assured, making them economically non-competitive with steel. Based

Jan 1, 1981

By Herbert M. Mandel

INTRODUCTION Designers of major public works projects in the past have displayed varying degrees of environmental consciousness, and tunnel designers in particular have always had to deal with certain environmental considerations - ventilation, lighting, aesthetics - as matters of primary design. Today, however, with a widening sector of the public becoming environmentally aware, tunnels are treated as elements of whole transportation systems, and are subject to increasing environmental scrutiny. The Route H-3 tunnels in Hawaii are examples of the time, care, and detail involved in a major rock tunnel project. Project Description The Route. Interstate Route H-3 is a proposed 10-mile highway crossing the Koolau Mountain Range on the island of Oahu, Hawaii, providing a direct connection between the Pearl Harbor area and the windward part of the island in the vicinity of Kaneohe. It is designed as a dual highway with provision to accommodate mass transit. As shown on Figure 1, the project includes two sets of twin bore tunnels (through the Main Koolau Range and through Red Hill), three highway sections of which two are through largely undeveloped mountain valleys (South Halawa and Moanalua), a viaduct, and three interchanges. From the Halawa Interchange to the Kaneohe Interchange, the proposed highway consists of two 3-lane roadways separated by a median where the highway is at grade. One lane of each roadway will not be constructed initially but will be landscaped and reserved for mass

Jan 1, 1974

By Pieter Barendsen

INTRODUCTION One of the main problems in tunneling without the use of explosives lies in the development of tools which, at an economically acceptable level, are capable of continuous breakage of the rock, resulting in a fragmentation suitable for a smooth, uninterrupted transportation of the muck away from the tunnel face. Tools employed on tunneling machines have, so far, always been of the mechanical kind which break up the rock by a crushing and shearing action. Other methods of rock breaking are possible but, even if some of them have reached the laboratory testing stage, nearly all of them are still too "exotic" to be of any practical use in the immediate future. One must admit, however, that some highly interesting results are beginning to be reported from the USA on the use of high pressure water jets for the destruction of rock through erosion, a field pioneered in Europe(USSR and Great Britain). Mechanical breakage of the rock is effected by inducing stresses exceeding its compressive/shear strength, by loading it with a wedge of cone shaped tool, until cracks are formed and chips loosened. In order to allow the tools to act upon the rock face continuously, they are commonly shaped as rotating bodies, "roller bits" or "disc cutters", spinning freely and mounted on a revolving boring head of tunnel diameter. The thrust of the tools against the face is generally exerted in a direction which is parallel to the tunnel axis.

Jan 1, 1997

By G. L. Dollinger, J. P. Kindsvater, J. A. Gibson

DESIGN AND DEVELOPMENT OF A MOBILE MINING MACHINE INTRODUCTION Until recently, developing tunnels in hard rock has been accomplished either by the drill and blast method or by using large tunnel boring machines. Combining the flexibility of drill and blast with the safety, efficiency and productivity of a TBM has been the objective of mining machinery producers for many years. In 1979 The Robbins Company began developing a new type of tunnel boring machine called the Mobile Miner to meet these objectives. The development and testing of the Mobile Miner is the subject of this paper. CURRENT MINE DEVELOPMENT METHODS Both the drill and blast method and the use of a TBM have notable advantages and disadvantages. The drill and blast method, for example, allows much more flexibility, requires less setup time and has a lower initial cost than a TBM; however it requires the use of high explosives and blasting has a disrupting effect on the rock surrounding the development. A TBM, on the other hand, is safer to operate, more efficient, more productive and produces smooth tunnel walls without disturbing the surrounding rock. In longer straight drifts it will easily out distance the drill and blast method. The TBM, however, is limited to boring a circular cross section tunnel which must then be modified if a flat floor is required. It also has a higher initial cost and an extended setup period.

Jan 1, 1985

By Sohta Takatsu, Hachiroh Mizubata, Shigeki Kudoh, Kazuya Takekuni, Yoshinori Yamada

A special type of shotcrete is used to improve the performance of open-type TBM in difficult situations. The Hakamagoshi and Johana tunnels are expressway evacuation tunnels of 3.2 km and 5.1 km in length, respectively (total 9.1 km) that were excavated by one open-type TBM. The geological conditions at the sites were estimated to be good before excavation. However, 95% of the rock turned out to be two ranking orders worse than the estimated classes. Therefore, we used a special shotcrete for bad rock conditions, and succeeded in excavating the tunnel at an average rate of 270 m/month.

Jan 1, 2001

By Robert M. Semple, Harvey W. Parker

INTRODUCTION Two promising innovative tunnel support systems are being developed by the Civil Engineering Department of the University of Illinois. One of these is a lining which can be placed by a slipform located immediately behind and contiguous with a tunneling machine. Recent advancements in construction materials appear to provide the breakthrough required to make such a system feasible and practical. The lining material which permits this construction scheme is wire fiber reinforced concrete made with high, very early strength regulated-set cement. Parts I and II of this paper relate to this slipformed liner. Part I discusses the material and equipment required to install the liner. The "Extruded Liner System" (ELS) has been devised to place the lining. This ELS concept is briefly described and a tentative development program is outlined. In Part II, the physical properties and practical construction aspects of the liner material are discussed and a program for structural testing of 10-ft diameter prototype tunnel supports is presented. Part III contains descriptions of improvements to conventional steel-rib tunnel supports. It is shown that square tubular box sections are structurally superior to wide flange sections for complex loading conditions often encountered in rock tunnels. Analytical studies and tests on connections have been performed to evaluate their structural behavior. These are presented along with a program for comparative large-scale tests on horseshoe-shaped frames with a 10-foot span. This research is being conducted by the Department of Civil

Jan 1, 1997

By N. Ward

The Gualcamayo Mine is located in the Andes Mountains north of San Juan, Argentina (Figure 1). A property of Yamana Gold Inc, it declared commercial production in July 2009 and has a total mineral reserve and resource base of approximately 88,000 kg of gold. Crushing operations for the open-pit mine are located in a 13,500 m3 underground cavern with a ceiling height of 22 m. More than 3,600 m of tunnels are used to access the cavern and convey the ore. The Project as described in this paper relates to the design and construction of the Main Cavern, Conveyor System Exit Tunnel, the Mechanical System Access Tunnels, and two 4.20 m diameter shafts (Ore Pass #1 and Ore Pass #2) as shown in Figure 2. [ ] Preliminary engineering for the Project was performed by Hatch Chile. Rizzo Associates Argentina, S.A., a division of Paul C. Rizzo Associates, Inc (Rizzo) was contracted to provide geomechanical and geotechnical support for the construction of the access tunnel system and geomechanical design and construction supervision for the cavern and shafts.

Jan 1, 2011

By S. Klein, M. McLeod, S. Gambino, K. Johnson, E. O’Hara

The Mokelumne Aqueducts Resiliency Project (MARP) involves construction of a 16.5-mile tunnel across the Sacramento-San Joaquin Delta (Delta) to replace the existing surface aqueduct pipelines with more resilient conveyance. The tunnel will be bored in Pleistocene-age alluvium at elevations between 100 to 10 feet below mean sea level. At this depth ground conditions are signicantly stiffer and denser than surcial soils and will mitigate potential seismic harards related to liquefaction ground shaking and cooding that could arise from potentially damaged levees. The heterogeneous soil deposits at tunnel depth consist of interbedded layers of stiff to very stiff clay and silt, and dense to very dense clean sand and silty sand.

Jun 23, 2024

By Hernan Fernandez, Khalid Saif F S Al- Khayareen, Volkan Salepciler, Jacek B. Stypulkowski

Wakrah and Wukair Drainage Tunnel, WWDT is 13 km long with a 4.5 m ID sewer water tunnel about 50 to 60 m below ground surface. Integral to the project are several adits with provisions for future connections as well as four work shafts, four intermediate access shafts, ancillary hydraulic structures, and an Odor Control Facility. The shaft depths range from 50 to 60 m. The project is constructed in aggressive ground with aggressive ground water. The construction activities require years of pumping and disposal of the ground water during tunneling operations as well as construction of permanent structures in shafts. Grouting of the corrosive rock mass in corrosive groundwater for the WWDT has been described in detail.

Jun 23, 2024

By Peter Dietrich, Joseph DeMello, Norbert Fuegenschuh, Kerwin Hirro, Jeff Brandt, Mike Cole

This paper presents a successful case history of the ground improvement efforts and excavation of twenty-three cross passages between twin bore tunnels driven by EPB tunneling machines in Los Angeles, California on Section 1 of the Westside Subway Extension. Unique and complicated ground conditions local to the tunnel alignment include San Pedro sands, siltstone/claystone Fernando Formation, and zones of “asphalt impacted soils.” To provide water cut-off and soil stabilization, jet grouting was performed prior to TBM excavation at the location of many of the cross passages. However, upon investigating the cross passages prior to excavation, the subsurface conditions required additional measures and SEM tools to ensure successful completion of the project.

Jun 13, 2023

By Dermot M. Ross-Brown

The objectives of this generic study were to use numerical modeling techniques to determine under what conditions seismic waves generated by an earthquake might cause instability to an underground opening, or cause fracturing and joint movement that would lead to an increase in the permeability of the rock mass. In general, the study showed that moderate earthquakes (up to 0.41 g) did not cause instability of the tunnel or major fracturing of the rock mass. An artificial rock-burst tremor with high accelerations, however, was found to be amplified around the tunnel, and fracturing occurred as a result of the seismic loading in salt and granite. In shale, even moderate seismic loading resulted in tunnel collapse.

Jan 1, 1981

By Irwan Halim, Bhoshaga Mitrran Ravi Chandran, Kevin Huynh

Tunnel segmental lining design constitutes a significant iterative process where modeling and numerical analysis are factors in deciding the number of segments, their dimensions, gasket placements, as well as the locations of dowels and bolts. Consequently, these modifications lead to revisions in the final drawing details. However, the current tunnel engineering practices lack systematic solutions that effectively bridge the gap between the iterative design process and efficient visualization of completed drawings due to the time- consuming nature of redrawing. This paper presents a pioneering application of AI-driven solutions including using Autodesk's API, for the Northside Interceptor Tunnel (NSIT) Project. It showcases the automation of drawing design and the real-time visualization of modifications, thereby streamlining the drawing process.

Jun 23, 2024

By Ronald E. Heuer

A 1995 RETC paper of similar title presented a method for estimating rock tunnel water inflow based on semi-empirical correlations with borehole water pressure tests. Since that time the author has found the method to be very useful, and it has been used by others in the industry. This current paper is an update which is intended to: A. More clearly explain assumptions and limitations of the method. B. Describe some case history examples. C. Respond to questions which have been raised; and extend the method to other considerations including distribution of inflow along the tunnel, panning requirements, interpretation of tunnel probe hole water inflow, and estimation of potential effectiveness of pre-excavation grouting to reduce water inflow.

Jan 1, 2005

By Donald P. Richards, Patrick Ramond, Martin Herrenknecht

Phase 1 of the second line of the Cairo Metro includes approximately 5.83km, of double track tunnels excavated in water bearing sand of the Nile flood plain. Closed face bentonite slurry shield tunnel boring machines 9.43m in diameter were used. State-of-the-art technology was used in TBM operations and guidance, with surface settlements averaging less than 14mm, and alignment deviations averaging less than 25mm. Production rates up to 580m/month were achieved, with average production of 4.8m/shift, 13.4m/day and78m/week. The completed tunnels, lined with precast concrete segments, are completely watertight under 20m of water pressure.

Jan 1, 1997

By Michael E. Allen

The building of sanitary and storm drainage sewers in urban or environmentally sensitive areas often requires the use of tunnel construction procedures. While hydraulic considerations may require only small diameters, traditional tunneling techniques make small sizes the least economical. Current state-of-the-art techniques using highly mechanized systems of pipe jacking can provide cost effective solutions to the problems of construction of small size tunnels. The characteristics of mechanized pipe jacking allow rapid advances under difficult ground conditions. The basic pipe jacking cycle is used with a variety of excavation systems to permit the contractor to satisfy engineering as well as economic parameters. These characteristics and several of the systems available are outlined.

Jan 1, 1981

By Richard E. Steffens

The underground portion of Duke Power Company's Bad Creek Pumped Storage Project in northwestern South Carolina consists of a powerhouse cavern (132 m. long, 23 m. wide, 50 m. high), 407 meters of shafts and approximately 3615 meters of tunnel, both lined and unlined, with diameters varying from 4.2 meters to 9.0 meters. A case history is presented, including the early pilot tunnel exploratory work and how this affected design, the design of the project, and the excavation, rock support and tunnel lining work. Problems and experiences encountered during the construction are given. The effects of high horizontal insitu stresses in the granitic gneiss are discussed along with solution taken.

Jan 1, 1989

By Ching L. Wu, Joseph Penzien

An analytical procedure is presented for evaluating the stresses in linings of bored tunnels caused by kinematic soil-lining interaction. Three cases of interaction as produced by the following conditions are treated: (1) relaxation of in situ soil stresses near a lining following its installation; (2) overburden pressure at the soil surface; and (3) free-field soil response resulting from an earthquake. Non-dimensional formulas and graphs resulting from parametric studies are presented for practical tunnel design applications. The procedure is applied separately to a steel lining and a concrete lining for a site located at the lower end of Market Street in San Francisco through which a BART (Bay Area Rapid Transit)tunnel passes.

Jan 1, 1997

By Charles H. Arnold, Timothy Fallara, David A. Day, Paul H. Marshall

The Upper Scioto West Interceptor Sewer (USWIS), Parts 1 and 2, consists of approximately 7,128 meters (23,385 ft) of 328 cm (129 in.) diameter tunnel. The project ex-tends from the City of Dublin to Griggs Dam in the City of Columbus. The majority of the tunnel was designed for excavation in rock by TBM. The remaining portions span pre-glaciation formed valleys in-filled with glacially-derived sediments. Tunnel construction in one of the glacial till filled sections includes excavation by drilling and controlled blasting. The other section will be constructed by ground consolidation followed by excavation by TBM. This paper describes the methods employed to mine the glacial till filled valleys.

Jan 1, 1997

By Stephen P. E. Redmond

A 15 km water supply tunnel is being constructed in Buenos Aires, Argentinata expand the capacity of the existing system. Two 4.3 meter diameter Earth Pressure Balance (EPB) tunneling machines operating at times from the same shaft on a congested work site and advancing through sedimentary deposits underlying this wonderful city pose interesting challenges. As of January 1999approximately 50% of the tunnel has been excavated. Combined machine production rates of 1026 m/month have been achieved. Presentations made in prior proceedings can be referenced for details of the overall Project scope and for details of the tendering process. The purpose of this paper is to compliment those presentations by addressing now the execution of the work.

Jan 1, 1999

By Steven Norris, William Moler, Michael Cole, Patrick Doig, Debi Lewis, Craig Pyle, Matthew Crow

The recently completed Lower Northwest Interceptor Program (LNWI) in Sacramento, California comprises, ten pairs of micro tunnels totaling 4,369 m (14,417 ft),three horizontal directionally drilled bores totaling 956 m (3,154 ft), and two large diameter tunnels under the Sacramento River totaling 1,198 m (3,953 ft). This paper briefly summarizes surface and subsurface conditions, and planning and design considerations. It then goes on to describe problems encounterd with each trenchless crossing, as well as lessons learned with respect to shaft construction, ground control at shafts during tunnel break-in and break-out, frac-out and heave, settlement, obstructions, coordination with permitting agencies, and application of geotechnical baseline reports.

Jan 1, 2007