Search Documents

By E. G. Gaylord

THE material improvements which have been made in the practice of exploiting oil and gas reservoirs in the United States during recent years may be attributed largely to: (1) The necessity for drilling deeper wells at costs not much greater than was formerly expended on shallower wells. (2) The necessity for producing oil at a lower cost per barrel. (3) A growing recognition of the importance of the nature of production practice upon ultimate yield of oil and gas. The first two of these factors result, to a large extent, from the fact that a greater proportion of new development has been deeper development, and these wells have been drilled in the face of progressively lower per well allowables. In California, for instance, maximum allowables have declined from 400 barrels per day in March, 1938, to 156 barrels per day in September, 1940, and during this same period some 125 wells were drilled to the deeper 10,000-foot producing horizons discovered during this time. The third item listed above results from our increasing knowledge of the basic factors which influence the amount of recovery we may expect from reservoirs. In addition to the longer-range planning now being undertaken by the more prudent operators, State proration and conservation laws have focused attention upon the importance of methods conducive to obtaining progressively greater quantities of the hydrocarbons in place. In a paper of this length it will be possible to discuss only a few of the recent advances. An effort has been made to select the more important of these and to indicate, where possible, the factors which have made these advances possible.

Jan 1, 1941

By P. Bacher, L. Dubourg, M. Jahazi, G. Dezaise

Effect of friction stir welding parameters and natural ageing on weld properties are reported. Using a Taguchi design of experiment, attempt is made to systematically examine the influences of the welding speed, tool rotation speed, forge force, tilt angle and pitch ratio on the weld size and ultimate tensile strength of FSWed joints. One millimetre thick plates of AA7075-T6 were welded in lap joint configuration. Samples were characterized by optical microscopy, hardness and tensile measurements. Trends suggested by the results and directions for further investigation are discussed.

Jan 1, 2006

By CIM Mineral Resource, Mineral Reserve Committee

Industrial minerals are generally considered to include non-metallic minerals, mineral products, or materials that provide raw material inputs for the construction, chemical, and manufacturing industries. They are often relatively low-value and bulky materials that are generally used close to where they are produced; however, some raw materials may be transported hundreds of kilometres to manufacturers and customers (ENDM, 2021). They do not include the metallic minerals, mineral fuels, or gemstones, and are used in industries based on their physical and/or chemical properties (Wikipedia, 2021). In contrast to most metallic minerals, a general distinguishing characteristic of the industrial minerals sector is their general low degree of market elasticity in relation to the market prices and product specifications. The estimation of either a Mineral Resource or a Mineral Reserve (MRMR) for an industrial minerals deposit can be affected to a significant degree by a number of factors that are not typically applicable to metallic mineral deposits. These factors can include such considerations as the particular physical and chemical characteristics of the final product, product quality issues, market size and market access. In some cases, such information may be confidential and proprietary. One of the key challenges of the industrial minerals sector is to define a commonly accepted listing of which types of minerals, materials, or mineral deposits can be considered as industrial minerals (Mining Standards Task Force, 1999). Although definitions for what constitutes an industrial mineral can vary in detail, general descriptions can be found in American Geosciences Institute (2021), Fastmarkets IM (2021), Snowden (2019), SME (2021) and Wikipedia (2021). A brief listing of some of the materials and minerals that are generally considered to be industrial minerals is provided in Table 1. For the purposes of this document, all references to industrial minerals include not only the minerals, materials, and mineral deposits themselves, but also the various commercial products that are derived from these sources.

Nov 19, 2023

By V. G. Papangelakis, S. Peters

Pressure oxidation of refractory gold ores can be conducted on ores with high carbonate content using just water or water with alkaline reagents to promote fast kinetics, and suppress the formation of elemental sulphur and CO2. In this work, a fundamental study was conducted to explore the silica-pyrite interaction in the presence of calcium and sodium carbonate. It was found that an alkaline environment increases the pyrite decomposition kinetics on one hand, but on the other dissolves silica, which encapsulates the dissolving pyrite thus hindering ultimately its complete decomposition.

Jan 1, 2011

By N. Chow, W. McCombe, G. Remple, J. Nikkari, L. Nightingale-Mercer

Orano Canada Inc. (Orano) operates the McClean Lake mill in northern Saskatchewan, processing high concentration uranium ore, delivered in slurry form, from the Cameco operated Cigar Lake mine. This slurry is ultimately processed into the purified uranium oxide product known as calcined yellowcake. During the calcining process, sulphate (SO42-) entrained in the yellowcake undergoes thermal decomposition into sulphur dioxide (SO2). SO2 is a colourless gas that poses health and safety risks. Since 2016, an anhydrous ammonia dosing system was successfully added to the existing Venturi particulate scrubber system to provide efficient removal of SO2 from the calciner off-gas. Within the pH controlled scrubber solution, SO2 exists in a pH dependent equilibrium with sulphite/bisulphite (SO32-/ HSO3-). The presence of a significant fraction of reduced sulphite and bisulphite in mill solutions presents a hazard in downstream circuits. Should these solutions drop in pH, either through natural oxidation or inadvertent mixing with low pH solutions, the solution equilibrium will shift from SO32-/HSO3- in favour of SO2, resulting in the evolution of SO2 gas from any liquid surfaces. In 2018, Hatch Ltd. (Hatch) and Orano implemented a design change in the calciner scrubber system. Blowdown from this system is now treated in an oxidation pre-step utilizing hydrogen peroxide (H2O2) and anhydrous ammonia (NH3) for pH control, in order to convert the residual sulphite/bisulphite present in solution to stable ammonium sulphate product. This paper will detail some of the challenges and actions undertaken to minimize SO2 risk, culminating in the recent introduction of a novel system designed to oxidize sulphite/bisulphite and prevent mobilization from the calciner scrubber solution into other mill areas where there is the potential for acidification and SO2 release.

Jan 1, 2020

By Gordon T. McKenna

"Syncrude Canada Ltd. is developing new concepts in lease-closure landscape design for its Oil Sands Leases 17 and 22 in northeastern Alberta. Closure planning is becoming an integral part of the planning cycles and of the lease operation. By incorporating closure planning into the day-to-day operation, the company will achieve acceptable lease closure in an economical manner. Ultimately, Syncrude will achieve lower operating costs through innovation in mine planning and a reduction in residual liabilities.New concepts being evaluated for lease-closure landscape design include: designing for closure, use of landforms and natural analogs, self-armouring bouldery ground, robustness in design, landform grading, terrain analysis of reclaimed land, geotechnical hazard assessments, choices in closure design timeframes, passive maintenance, determining post-closure monitoring goals, engineering tailings, engineering other substrates, use of test plots and field demonstrations, geomorphologic monitoring of reclaimed lands, defining closure goals, and visiting other mines. These concepts are being formalized under the new discipline of Landscape Engineering."

Jan 1, 1996

? A BARGE WILL BE INSTALLED IN THE BOTTOM OF A COMPLETED PIT. ? THE PROVEN BAUER CUTTER TECHNOLOGY WILL BE INSTALLED ON THE BARGE AND A DEWATERING PLANT WILL BE INSTALLED NEAR THE BASE OF THE PIT RAMP. ? THE WATER LEVEL IN THE PIT WILL BE RAISED BY 20- 40 METRES AND REMAIN CONSTANT OVER DURATION OF MINING. ? THE CUTTER WILL BE LOWERED TO MINE 10 METRE DEEP BENCHES ON A CHECKERBOARD PATTERN TO AN ULTIMATE DEPTH OF 200 METRES. ? THE 5? MINUS CUTTINGS WILL BE PUMPED TO THE DEWATERING PLANT, DEWATERED, AND TRUCKED TO SURFACE.

May 1, 2003

By J. H. Canterford

The nickel industry in Australia has followed the general pattern apparent in many other regions - lots of ups and downs, successes and failures, but always plenty of challenges. Some of these can be attributed to local geographical and infrastructure factors, others to a healthy mix of corporate good luck and management countered by decisions that, in retrospect, were less than optimum. The roles of several entrepreneurs have certainly added plenty of spice! In terms of processing technologies, there was an initial heavy reliance on the use of "off the shelf' commercially proven processes such as ammonia leaching of concentrates and mattes, and flash smelting. Over the past decade there has been an increasing dominance of plant modifications and process technologies that have been developed "in house" in order to enhance project economics and exploit lower grade and more complex resources. This presentation provides an overview of the past 40 years of the major developments in the Australian nickel industry and concludes with some guesses as to where we will be in another decade or so.

Jan 1, 2005

The effect of long term exposure of full size bolts to corrosive environments is presented. A special test rig was used to test four bolts under different loading conditions. Four, X-grade identical profile bolts, each of 21.7 mm core diameters (23.7 mm full diameter) were subjected to prolonged corrosion testing using acid sulphate water. The pH value of the circulated water varied between 3.4 and 4.3. The corrosion exposure test period lasted three and half years. Two bolts were axially loaded to 10 and 20 tonnes force respectively, the third bolt was subjected to a 360 Nm torsion load and the fourth bolt was left unstressed to act as a reference bolt. After the test period ended, the bolts were stripped of their corroded coatings and weighted for weight loss. The diameter of each bolt was subsequently measured, and the loaded bolt samples were first tested non-destructively for tensile cracks and then tested for tensile failure. No cracks were found on post corrosion bolts tested non-destructively. The failure strength reduction on all four post-corroded bolts was significant, varying between 21% and 39%. The onset of corrosion was not confined to the targeted mid-section length of the bolt, however, the severest corrosion occurred at the anchored ends of the bolts.

Aug 1, 2013

By C. Graham

Thin Spray-On Liners (TSLs) have been researched and in development for over two decades and yet their fully functional and widely justifiable application in mining has yet to be achieved. While the explanation for this is partly technical, it is also clear that proving and communicating the operational and economic case for why a mine should change from mesh or shotcrete liners to a TSL is not a trivial matter. Evidence must be presented and communicated effectively, that is both obvious and compelling for a mine operator. The paper describes recent work carried out and directed towards this end, with funding from CAMIRO?s Deep Mining Research Consortium and additional support from 3M Canada and ABB Canada. The essential progress that has been, or is in the process of being made, will be described in providing the necessary proof of acceptable or superior TSL performance in the following areas: polymer formulation, health and safety, geotechnical specification, robotic liner application, business case economics and yielding ground support effectiveness. Future plans are also presented to demonstrate the performance of a new 3M composite TSL/yielding bolt support system in underground trials where the substrate rock is intended to fail through a number of mining-induced mechanisms.

Aug 1, 2013

By H. Blaha, H. Wagner

"Room and pillar workings in salt mines are preferred sites for underground waste disposal. A critical issue in selecting waste disposal sites is long-term behaviour of such workings. The long-term behaviour of salt pillars is controlled by the pillar geometry, i.e. the height, width and length of pillars and the level of pillar stress. The latter has a strong influence on creep characteristics of salt pillars whereas the width to height ratio of salt pillars determines the strength of pillars and the deformation characteristics of salt pillars.Three different regimes of pillar creep behaviour of salt pillars can be distinguished, namely a stress level below which the rate of creep approaches a value of zero, a stress range where the rate of creep is constant and finally a stress level above which the rate of creep accelerates. Long-term stability of room and pillar workings can be assured only when the pillar stress level falls within the first stress regime. Strength and creep tests on model salt pillars have shown that at stress levels below 40% of pillar strength the rate of creep approaches a value of zero, between stress levels of 40% and 65% the rate of creep is constant but increases with stress level. Above pillar stress levels of 65% the rate of creep accelerates.Long-term measurements of pillar deformation and surface subsidence above relatively shallow room and pillar workings in salt mines have confirmed these observations. Long-term strength of salt was found that be between 60% and 65% of short term strength. The evaluation of salt pillar behaviour on the basis of critical pillar stress levels was found to be superior to the traditional factor of safety concept because it allows relating pillar deformation measurements to actual pillar conditions. The approach described in the paper was used successfully to evaluate the stability of room and pillar workings in a salt mine and to design strategies to stabilise critical pillar workings."

Jan 1, 2015

By S. K. Shaha, W. Kasprzak, D. L. Chen, J. Friedman, F. Czerwinski

The role of solutionizing conditions within the T6 heat treatment of the cast Al-Si-Cu-Mg alloy with micro-additions of Zr-Ti-V was assessed in terms of their influence on microstructure and mechanical properties. As a solution treatment, a single step process at 485 and 510oC and a two-step process at 510 and 525oC for varying time intervals from 0.5 to 9 h, were examined. In all cases, solution treatment was followed by isothermal aging at 150oC for 100 h. The microstructural analysis showed that the solution treatment changed the eutectic silicon morphology from needle-like, present after casting, to spherical shape in the T6 state and that the extent of changes was strongly influenced by temperature and time. The Cu- and Mg-rich phases completely dissolved during solution treatment while the Fe-containing phase, Al8Si6Mg3Fe, remained partially in the microstructure. The Ti, V and Zr containing phases, Al13Si2Ti3Zr and Al3Si26FeTiV10, present in as-cast state, were partially dissolved during solution treatment, reducing their size by 10 - 48%. The studied alloy reached the maximum ultimate tensile strength of 335 MPa and yield stress of 303 MPa for two-step solutionizing with a total time of 4.5 h. It is concluded that the two-step solution treatment resulted in higher tensile properties than the single-step process.

Jan 1, 2015

By F. H. Samuel, J. E. Gruzleski, S. Valtierra, H. W. Doty, F. J. Tavitas-Medrano

319-type cast Al-Si-Cu-Mg alloys are commercially important due to their popular use in automotive applications. Artificial aging heat treatments are commonly performed in these alloys to achieve precipitation hardening and, therefore, improve their mechanical properties. The present work was carried out to investigate the effect of conventional (at a constant temperature, as specified by the standard T6 heat treatment regime), and non-conventional multi-temperature and interrupted aging cycles on the hardness, tensile and impact properties of two 319-type alloys (with and without Sr+ Mg additions). The results show that certain multi-temperature aging cycles have a more favourable effect in improving some mechanical properties than conventional cycles.

Jan 1, 2006

By George Wilkinson

"AbstractThe consistent relationship between the availability of electrical energy and our economic wellbeing is well known. As we develop the energy we need to nurture industrial civilization in decades ahead, we will at the same time reduce our reliance on dwindling supplies of oil and gas. Coal and uranium will be developed as our major fuel sources to meet medium-term. energy needs, followed by fusion and solar energy for the long term.IntroductionTHIS PAPER treats the matter of energy in a way that is quite different from that of the crisis-type atmosphere which surrounds so much of it currently in the news media. On the one hand, we lift the whole subject of energy out from its present-day involvement with short-term issues and take an important longer-term look at the solutions which lie before us. On the other hand, we recognize that short-term issues are important and, as we are reading and hearing, many of the right short-term solutions continue to elude our politicians, our policy makers, and even some of those with knowledge and authority in the energy field.A year ago, if you asked people how they would go about conserving energy, they would probably have said turn out the lights. They would probably say the same thing today, but they might also include other things such as driving the automobile more slowly or putting more insulation in the attic. However, their first impulse is still to use less electricity."

Jan 1, 1977

By D. Harrington

Ventilation of underground workings consists in establishment of such control of air currents that the underground workers may work in safety, with maximum comfort and efficiency, and without impairment of health; and requires that the mine openings may be made subject to such control of air flow as to remove from these workings at ordinary times harmful gases and dusts, and that, at time of emergency, such as fire or explosion, there may be maintained as much or as little air flow as may be desired covering portions of the mine or the mine in its entirety. Control of air flow is the keystone of any ventilating structure, and this very essential feature is obtainable only by the installation of mechanically-operated fans, together with other;. ventilating devices such as doors, over-casts, regulators, etc. Every mine, large or small, coal or metal, should from the outset be equipped with a fan. While much has been written about natural ventilation and many claims made that in specific mines there is sufficient natural air flow, there are few if any mines, coal or metal, where natural ventilation supplies anything like adequately safe or healthful conditions for underground workers even at ordinary times; and at a time of mine fire or explosion, mines depending upon natural ventilation are practically helpless, and certainly are decidedly dangerous to those unfortunates forced to be in them. While ventilation has practically always been deemed an integral part of coal mining, metal mines have rarely paid much, if any, attention to air circulation until forced to do so by occurrence of some untoward condition or accident. Yet metal mines actually have as great need of efficient circulation of air as have coal mines. The coal mine must remove the dangerous explosive gas, methane, also fumes from explosives and, in occasional places, other gases such as carbon dioxide or nitrogen.

Jan 1, 1933

By A. R. House, G. W. Shepherd

Newmont USA Limited owns and operates the Phoenix Mine near Battle Mountain, Nevada, USA. The existing milling facility has operated since 2006 (House, 2010). Following the startup of the milling operation, and coupled with the upswing in the copper market, Newmont realized that Phoenix had no process option to treat transition and oxide copper ores. This meant that potentially revenue generating ore would be mined as waste. With no system in place to treat the transition and oxide copper, work began to determine the most feasible approach. After evaluating multiple options, the flow sheet was set for a runof- mine (ROM) heap leach pad and solvent extraction/ electrowinning plant (L-SX/EW). This paper will discuss the eight years of successes and challenges with developing the copper L-SX/EW plant and achieving commercial production of copper cathode.

Jan 1, 2014

By J. D. T. Steyl

Anglo American Corporation and the University of British Columbia have developed a medium-temperature oxygen pressure leaching process for the extraction of copper from chalcopyrite concentrates in an acid-sulphate system (AAC/UBC process). Leaching is performed at 150°C and surfactants are added to disperse molten elemental sulphur from the unreacted sulphide surface to prevent liquid sulphur occlusion. Copper extractions of over 95% and elemental sulphur yields of around 60% were observed over a 2-hour average residence time in a continuous pilot autoclave. Sporadic blockages occurring under continuous conditions were found to be caused by the accumulation of molten elemental sulphur mixed with unreacted sulphide mineral. A batch programme of experimentation was undertaken to establish the reason for this phenomenon. Batch experiments were conducted at low pulp densities on concentrate samples with narrow size distributions and at similar solution compositions to those experienced in the pilot autoclave. The overall rate of chalcopyrite oxidation was shown, under approximately constant solution composition, to be a strong function of the total available mineral surface area. Initial copper extraction rates followed the shrinking particle kinetic model under intrinsic surface control. Deviation from shrinking particle kinetics was however observed after a certain oxidation time. Secondary electron images identified small (typically less than 20 µm) sulphur conglomerates at the point of deviation, which 'collected' unreacted chalcopyrite mineral particles and lowered the total mineral surface area available for oxidation. These sulphur clusters are thought to be the precursor for blockages experienced in the continuous pilot autoclave. These results emphasised the importance of fine grinding (P80 5-20 µm) and suggest that shorter residence times may minimise the formation of sulphur conglomerates in a continuous autoclave operating at medium temperature.

Jan 1, 2004

By X. M. Zhou, T. Wu, He X. N.

"In order to study the support effect of concrete in the surrounding rock of a metal mine, the concrete and surrounding rock were comparatively studied. Firstly, the general situation of the ultra-kilometer deep shaft in Xincheng, surrounding rock and geological conditions are introduced. Secondly, the experimental scheme of material mechanical properties of surrounding rock and shaft lining concrete based on same standard dimension and shape are examined, and the mechanical tests of rock and concrete based on different shapes and sizes are carried out. The study shows that the compressive strength value and elastic modulus of the rock cube are 1.28 times and 1.78 times that of the cylinder, and the Poisson's ratio is 0.77 times. The dimensional effect law of the concrete cube and cylinder test data is consistent with the rock law. However, the test results of the concrete are less discrete than the rock; the test also shows that the strength and elastic modulus of the concrete lining of the main shaft of the Xincheng are much smaller than the surrounding rock that is also used as the concrete aggregate, which indicates that the support of concrete lining in the surrounding rock shaft behaved weakly. Based on the development of the modern NATM rock support theory, it is suggested that the mechanical test standard of artificial support materials should be unified into the mechanics test standard of natural rock, which will help to improve the accuracy and practicality of scientific calculation of geotechnical engineering.INTRODUCTIONConcrete and rock mass are usually attributed to a class of materials called frictional materials or geotechnical materials, of these two kinds of materials, the first is man-maded and the second is natural. The attentive scholar can find that there are many differences in the test criteria for the mechanical properties of the two kinds of materials among different industries or departments, reflecting the differences in their sources, tradition, and the application thoery of material strength among them.There is a situation wordwide, that there are many testing standards of the same material mechanical parameters such as elastic modulus, compressive strength, etc. The cube with a side length of 150 mm is adopted as a common sample in the architecture department in China, while a cylinder with a diameter of 50 mm and a height of 100 mm is as a standard specimen in geotechnical department.Knowing that mechanical parameter values are strongly affected by the the size, shape of specimen and loading rate etc, that is to say the mechanical parameter values of the same material are completely different when obtained from different test with different standards. However, such a problem has been long neglected in geotechnical engineering."

Jan 1, 2019

By D. F. Sherwin

"THE AREA which is described in this paper (Fig. 1) includes the continental margin of eastern Canada extending from the Gulf of Maine to the north edge of the Grand Banks, which, including the continental shelf, slope and rise, comprises an area of about 600,000 square miles. The paper is intended to give a background of the geological setting of this region in the context of its ultimate potential for oil and gas reserves in close proximity to the Nova Scotia energy market.HISTORY OF EXPLORATIONThe history of geological exploration of this area really began in 1878, when U.S. fishing boats brought back samples of rock recovered in trawls from their expeditions to the long-famous fishing banks off Canada's East Coast. Tertiary and Cretaceous fossils recovered from these samples indicated that the eastern Canadian continental shelf was actually the submerged northern extension of the Atlantic Coastal Plain."

Jan 1, 1972

We describe a new method of characterising the effect of dissolved materials on the rate of coalescence of bubbles in aqueous media. Single bubbles were allowed to rise to meet the surface of an aqueous solution, and the time of persistence between arrival and bursting of bubble was measured as a function of solute concentration. A laser beam was placed just above the surface of the liquid, with a detector in the light path, so that any disturbance at the surface could be seen as a break in the beam. The arrival of a bubble at the surface could be detected from the behaviour of the trace on an oscilloscope, and when the bubble broke, another significant change in the signal could easily be seen. The time between disruptions was reported as the persistence time. The effect of a homologous series of n-alcohols (C1 to C8) on the persistence time was measured, in aqueous solution. It was found that with increasing concentration of a particular solute, the persistence time increased up to a point, and then declined. However the magnitude of the persistence time was found to increase with increasing numbers of carbon atoms in the molecule. Bubbles of 1, 2 and 3 mm diameter were used. Persistence time increased with increasing bubble diameter, the maximum values observed being of order 100 secs. For a given solute, the persistence (drainage) time increased with increasing bubble diameter. The concentration Cmax at which the maximum persistence time was observed, was found to be independent of the bubble size. It decreased uniformly as the carbon number increased, and was well correlated by the function y1/2 (dy /dc) -2 I dc)-2 . There was no apparent correlation with the surface excess at maximum persistence time.

Jan 1, 2006