Search Documents

By J. Philip Bromberg

The 1977 Clean Air Act Amendments will have a large effect on the coal-fired segment of the electric utility industry. Since electric power generation constitutes by far the largest single use for coal, this legislation has the potential to greatly affect future patterns of coal utilization in the U.S.A. The inability to depend exclusively upon low sulfur coal as an exclusive mode of compliance with New Source Performance Standards may greatly lessen projected demands for low sulfur coal by eastern utility boilers. The requirements of the legislation is discussed with particular reference to the needs of the electric generating industry, along with the technologies available for complying with the Act.

Jan 1, 1978

By Fred J. Fleischauer

Industry requires higher speed sheet stacking. High speed sheet stacking requires equipment and techniques to solve several inherent difficult problems, such as the tendency for sheets to sail, and the need for a means to absorb the kinetic energy of the sheet without damaging the sheet. Accurate alignment of the sheets on the stack is another problem difficult to solve. The paper first analyzes the process of sheet handling into its basic elemental steps. It then describes equipment and techniques presently used for moderate sheet handling speeds, with emphasis on how each step in the stacking process is accomplished by the present equipment. The limitations to speed-up of present equipment is discussed. New high speed equipment, either recently introduced to the market, or in the process of development, is described. Magnetic, air float and vacuum conveyor stackers are compared.

Jan 1, 1973

By Charles M. Pelanne

Without insulation we could not survive on this planet. This may sound like a self-serving statement but it is a fact. The blanket of air which surrounds us is a very effective insulating blanket, allowing some shortwave solar radiation to warm us during the day while retaining the longer infrared radiation at night. Our life on earth is very much dependent on materials performing an insulating function without being thought of as insulation, clothing, fur, window glass, the ice of an igloo etc. The mechanisms of heat transfer involved in these materials are analogous to those involved in engineered insulations - Engineered insulations are designed for maximum effectiveness for given conditions within the applicable retraints. Engineered insulations are very effective! As an illustration let us consider this graph (Figure 1). It represents: 1. The radiative heat transfer between two 1 foot2 (0.0932) radiantly black surfaces, one at 100F (38C) and the other at the temperature indicated on the bottom scale. This does not include the convective and conductive heat flow of the air, both of which are significant but small in comparison. 2. The heat transfer resulting from the placement of 1 inch (25.4 mm) of insulation [10 pcf (160 kg/m3) ceramic fiber] between these two plates.

Jan 1, 1976

By S. Todd Mickleborough

The geostatistical technique of conditional simulation is applied to measure the uncertainty in factor of safety predictions for soil slopes where there is incomplete knowledge of the spatial distribution of soil properties. A case study considers a natural clay slope in Canada. The sequential indicator simulation technique is used as a means for generating a series of spatial maps of soil properties for this site. These maps approximate random draws from the conditional probability density function that characterizes existing uncertainty in the spatial distribution. Factor of safety determinations are then made for each simulated map using the simplified-Janbu approach, where the computations are performed with a new computer program that can operate on irregular spatial profiles of soil properties specified on a discrete grid. A unique capability of this approach is the ability to generate the distribution of factor of safety conditional to the type, position, and value of existing site characterization measurements. This capability should reduce uncertainty in FS predictions.

Jan 1, 1993

By Paloma Lazaro, Moe Momayez

Interactions between human beings and their work environment require the body to regulate its temperature by balancing heat production and loss. Comfortable environmental conditions are crucial for keeping workers safe and healthy and to maintain a suitable level of productivity. However, achieving a proper core body temperature may become challenging under different conditions, especially in high heat-generating workplaces such as hot underground mines. Because hot underground mines have the potential to expose workers to heat stress, compliance with standardized and regulated indices and criteria is distinctly required. The objective of this paper is to provide an overview of the current research on heat stress and strain in hot underground mines, collected from published and specialized literature. General definitions, statistics of heat-related accidents in mining, overview of the indices, standards, and recommendations for heat stress are provided herein.

Oct 6, 2020

By M. Raffaldi, J. Johnson, M. Stepan, D. Benton

"The Office of Mine Safety and Health Research (OMSHR), Spokane Mining Research Division (SMRD), is continuing its High-Energy High-Displacement (HEHD) testing of field-scale shotcrete panels. A test program was developed to determine the relationship between applied force, displacement, and energy for both unreinforced and reinforced shotcrete panels. Reinforcement options consisted of synthetic macro-fibers, sprayed polyurea liners, chain-link fence, welded-wire mesh, and combinations of these products. During testing, photogrammetry was used to measure the geometric changes of the panels, including volume changes and panel cracking. These measurements were correlated with the load and displacement data, allowing visual observation to be related to the applied force and displacement. The test results provide a comparison of the mechanical performance of the various panel types and can be used by the practicing engineer to evaluate installed support based on visual observation of cracking and deformation. Visual assessment of the loading cycle and strength capacity of shotcrete in underground excavations will improve mine safety by providing a means to quantify the stability of installed shotcrete support. INTRODUCTION The National Institute for Occupational Safety and Health (NIOSH), Office of Mine Safety and Health Research (OMSHR), Spokane Mining Research Division (SMRD) is continuing research on the behavior of shotcrete when used as the surface support component in mining ground support systems. Ground control safety often depends on supporting, or at least containing, the ground between the rockbolts. Shotcrete and mesh, in various combinations and with other components, are often used to accomplish this (Figure 1). Maintaining support pressure during ground deformation is key to the performance of these systems, and to ensuring miner safety. However, the toughness of a ground support system–the ability to maintain strength over large deformations–is difficult to quantify. Researchers at SMRD have responded to this deficiency by designing a full-scale test device, described previously by Martin et al. [2015a], and beginning a testing program to assess the behavior of shotcrete surface support reinforced with a variety of products including: fibers, chain-link mesh, welded-wire mesh, spray-on polyurea liners, and combinations of these products. This paper presents the findings of these tests."

Jan 1, 2016

By Miguel Reyes, Chenming Zhou, MATTHEW GIRMAN

Electromagnetic energy emitted from electronic devices has been known to interfere with other electronic systems, hindering their ability to function properly. Mines have many electronic devices critical to the health and safety of mine workers that could be negatively affected by electromagnetic interference (EMI). To ensure that devices are electromagnetically compatible, tests must first be conducted to measure emissions and check for immunity. There are many standards available across multiple industries that prescribe emission limits and test methods for electronic devices. Due to the unique environment of an underground mine, it may not be enough to simply adopt a standard from another industry to mining. A literature review has been conducted, and an overview of EMI standards in other industries will be provided in this paper. Also, an example of how a standard can be applied to mining equipment is presented. Finally, recommendations on standards which could potentially be applied to mining will also be included. This work will inform the mining industry of EMI standards in other industries so that mine workers and technology manufacturers have guidance of the steps that can be taken to investigate and reduce the impact of electromagnetic interference and potentially work toward electromagnetic compatibility. The findings and research involved in this effort can also be used to explore the need to develop mining-specific EMI recommendations and standards.

Nov 25, 2021

By Yun-tao Xin, Yu Yi, Kang Yan, Gang Li, Xiao-dong Lv

This study investigated the selective removal of arsenic from high-arsenic dust in alkaline systems and the effects of different leaching conditions. The results indicated that the liquid–solid ratio, NaOH concentration, and sulfur dosage had a significant influence on the process. The leaching efficiency of arsenic reached 99.57%, while that of lead was as low as 0.03% under appropriate conditions. In particular, the addition of sulfur can effectively promote the leaching of arsenic and reduce the dissolution of lead in the solutions. An artificial neural network was used to model the leaching process. It consisted of a back-propagation artificial neural network model with a “6–10–2” structure that could effectively simulate and predict the value with more than 99% accuracy. Based on the difference in weights of the different parameters in the neural network model, the relative importance of the parameters related to arsenic and lead leaching efficiency was obtained, which followed the order of NaOH concentration, liquid–solid ratio, sulfur dosage, temperature, time, and stirring speed.

Jul 29, 2021

By JESSICA W. A. AZURE, Kansake A. Bruno, Samuel Frimpong, AZUPURI G. A. KABA, FORSYTH A. KADINGDI, PROSPER E. A. AYAWAH

Blasting generates undesirable ground vibration with adverse effects on humans, the environment, and structures. Numerous studies have used various techniques including machine learning (ML) to predict the peak particle velocity (PPV) caused by blasting in surface mines. These studies used the validation-set approach to evaluate the performance of their predictive models. In this study, Random Forest (RF), Gaussian Process (GP), and Gradient Boosting Machine (GBM) were applied for the prediction of PPV using data from a large open-pit gold mine in Ghana. An ensemble model based on a stacked generalization approach was then built on these three base models to significantly improve the PPV prediction performance. The model evaluation was done using repeated tenfold cross-validation which resolves the challenges with the validationset approach for small datasets. The dataset used in this study comprised a total of 196 measurements taken from different blasting operations. R-squared ( R2 ), mean absolute error (MAE), and root mean square error (RMSE) were used to evaluate the model performance. The results obtained from these models revealed that all the base models did not significantly outperform each other. However, the stacked generalization approach had a better performance, with RMSE = 0.12, R2 = 0.96, and MAE = 0.07. This approach presented an improvement over the existing methods and will be useful for highly accurate predictions of ground vibration during blast design. The application of this model will be useful for efficient and effective blast design.

Nov 8, 2022

By Dongjie Zhang, Shuxin Liu, Jianduo Wang

Broken rock mass and unreasonable stope structure parameters can cause excessive ore loss and dilution in sublevel caving; this is the main problem faced by caving mining in recent years. This paper proposes a stope structure parameter optimization method suitable for steeply inclined medium-thick broken ore bodies and evaluates the reliability and effectiveness through case studies. To solve the problem of large ore loss and dilution in the high-end wall sublevel caving method of Xilinhot fluorite mine, it is necessary to select proper stope structure parameters. Based on the theory of random media, an end-wall ore drawing experiment was carried out, and the bulk flow parameters needed to optimization of stope structure parameters were determined. In the experiment, it was found the draw-out body of high-end wall ore drawing showed a fine top and a thick bottom; the granular media had good fluidity. The reasonable caving step is determined to be 1.2 m instead of the 1.6 m originally used. Through the optimization experiment of the mining route position along the vein, the study found that the best route position is different with the ore body inclination. When the inclination angle of the ore body was 90°, the reasonable route was located in the center of the ore body. When the inclination angle of the ore body was between 85° and 90°, the route moved from the center of the ore body to the footwall at a rate of 22.5%. When the inclination angle of the ore body was between 80° and 85°, the route moved to the footwall at a rate of 54.8%. When the inclination angle of the ore body is not greater than 80°, the route should be arranged on the boundary of the footwall. Field application results showed the dilution rate reduced by 7.66% and the recovery rate increased by 7.31%. Field test results verify the effectiveness and applicability of the optimized stope structure, which corroborates the effectiveness and applicability of the optimized stope structure.

Mar 10, 2022

By Shailendra Chawla, Ashok Jaiswal, B. K. Shrivastva

The study aims to evaluate the pillar behavior during the depillaring operation by continuous miner (CM) technology. A panel with five headings developed as per the coal mine regulation of Indian coal mines [2] has been selected for the study. The depillaring operation has been carried out using CM technology after widening and heightening the original entries. An extensive field investigation has been carried out throughout the depillaring operation to access the mining conditions. Depillaring operation has been performed smoothly up to the middle of the panel (fourth row out of eight rows of four pillars each). Advanced blinking of the auto warning tell-tale (AWTT ) has also been observed on some of the instruments during the splitting of pillar no. 18. The panel shows extremely difficult mining conditions at this stage. The case has been numerically simulated using three-dimensional numerical techniques. The simulation result has indicated the high stress and yield condition on the working and the barrier pillar (surrounding goaf from both sides) after the extraction of pillar no. 18. The analysis has also indicated the marginal stability of the 2nd barrier pillar (namely “pillar B”). The failure of the barrier pillar could be the responsible for global instability of the panel as observed in the field. Understanding the importance of the barrier pillars, panel design has been modified by incorporating an additional row of barrier pillars. The stability of the modified panel has been evaluated. Both working and barrier pillars have been observed stable in the modified panel. This could be an alternative layout considering safety at the working face.

May 8, 2022

By Samir Kumar Pal, Rajasekar Rathanasamy, Gobinath Velu Kaliyannan, Moganapriya Chinnasamy, Sathish Kumar Palaniappan

The research examines the performance of uncoated and coated tungsten carbide-cobalt rock cutting bits. It aims to optimize process variables (cutting speed, depth, coating material) considering multiple output responses (cutting forces, specific energy, wear rate, material removed, angle of reaction forces). The study uses a hybrid optimization technique combining Taguchi design, grey relational analysis, and fuzzy logic. The optimal parameter combination was found to be cutting speed: 200 mm/s, cutting depth: 6 mm, and titanium aluminum silicon nitride coating.

Apr 24, 2022

By Mark Colwell

This paper summarizes the results of a research project whose goal was to provide the Australian coal industry with a longwall installation roadway (faceroad) design methodology that could be utilized by suitably qualified colliery personnel. This goal was achieved in 2012 and the design methodology (and software package) is referred to as Analysis and Design of Faceroad Roof Support (ADFRS). The intended benefits to underground operations, in the provision of this information and resource, are a safer and more productive workplace.

By Larissa Koroznikova, Steve Durkin, Patrick Bouwmeester, Michael Tuck

In currently used mining methods, blasting techniques often causes dilution of valuable ore and results in costly processing requirements. In the context of narrow vein mining of thin and highly concentrated orebodies there is a need of a mining method that can reduce dilution in order to remain economically viable. This research project explored the viability of a new mining technology, thermal fragmentation, in narrow vein mining. Thermal fragmentation technology uses a flame jet to produce extreme heat that spalls the surrounding rock to a strategically located drill hole, as an alternative to traditional blasting. This paper creates a net present value (NPV) model of a mining method using thermal fragmentation, as well as for an existing method used for narrow vein mining; comparisons and evaluations were made regarding the feasibility of the new technology. It was found that while overall costs for thermal fragmentation were relatively high, reductions in wages, haulage and processing costs, as well as increased productivity and ore recovery, meant that the new method would improve the financial performance of any operation. These results identify that there is an opportunity to introduce the thermal fragmentation technology to narrow vein mines within Australia, in order to lower costs and increase profit.

By D. Robert Weir, Verner B. Sefton

The reduction roast-ammonium carbonate leach-hydrogen reduction process for laterites has been under development by Sherritt Gordon for the past 20 years. The process can treat high iron or low iron laterites, with some process modification, and gives extractions of 88-93% Ni or 82-88% Ni, respectively. Five campaigns on a 1 tonne per day Pilot Plant and four campaigns on a 35 t/d Demonstration Plant have been carried out on laterite from three different deposits, and many other laterites have been investigated in the laboratory. The Marinduque Surigao Nickel Refinery in the Philippines was designed on the basis of this work. The process comprises roasting to selectively reduce the nickel and cobalt in the laterite, leaching the calcine in ammonium carbonate to dissolve the metals, recovery of cobalt by precipitation of a mixed metal sulphide, concentration of nickel from the carbonate solution by basic nickel carbonate precipitation and recovery of high purity nickel by hydrogen reduction of nickel from ammonium sulphate solution. Ion exchange has been developed as an alternative to BNC and for recovery of trace nickel from BNC barren liquor. Details of the development of some of the process steps through the laboratory to commercial plant are discussed. The process metallurgy has been confirmed in the commercial plant.

Jan 1, 1979

By James C. Barker

Alaska?s known mineral endowment includes some of the largest and highest grade deposits of various metals, including gold, copper and zinc. Recently, Alaska has also been active in the worldwide search for sources of rare earth elements (REE) to replace exports now being limitedby China. Driven by limited supply of the rare earths, combined with their increasing use in new ?green? energy, lighting, transportation, and many other technological applications, the rare earth metals neodymium, europium and, in particular, the heavy rare earth elements terbium, dysprosium and yttrium are forecast to soon be in critical short supply (U.S. Department of Energy, 2010). The REE, accompanied by other high field strength metals (such as Nb, Zr, Ti, Th, W), are associated with alkaline complexes of the Hogatza Belt in northwest Alaska; peraluminous tin-granites of the Ruby batholith in central Alaska and the Porcupine plateau in the northeast; and peralkaline intrusive complexes in the southwest Alaska Range west of Anchorage, and on Prince of Wales Island in southeastern Alaska. Limited evidence suggests that the heavy REE are associated with deposits that became more highly evolved by late hydrothermal processes.

Jan 1, 2012

By M. S. Klima

This paper will detail the work that has been done in 1990 and 1991 at the Pittsburgh Energy Technology Center (PETC) on the development of the U.S. Department of Energy's (DOE) patented Micro-Mag Process. This process entails the use of a micronized-magnetite (minus-10 microns) and water mixture for cleaning fine coal (minus-600 microns) in a cyclone, along with the production and recovery of the magnetite. Emphasis will be on the results from micronized-magnetite recovery testing using both conventional wet-drum and high-gradient magnetic separators in which several key operating conditions were varied including feed percent solids, magnetite-to-coal ratio, magnetite grade, and feed rate. Also presented will be selected results from testing done on a 76-mm diameter cyclone at a relative density of 1.50 showing the effects of operating pressure, magnetite grade, and medium-to-coal ratio on separation efficiency. In addition, two methods for producing micronized magnetite, along with the corresponding size distributions, will also be discussed.

Jan 1, 1992

By J. Fuchs

This paper describes the mechanized narrow vein cut-and-fill approach used for the Deep Copper orebody at Falconbridge Limited's Strathcona Mine. Strategies for achieving high productivity while maintaining ground stability at depth and controlling dilution are discussed, including the use of mini-electrohydraulic drilling equipment, containerized truck haulage, consolidated rockfill placement techniques, and a miners' incentive system.

Jan 1, 1992

By W. F. McDermott

The transportation of solids by pipeline is not new. In 1891 a United States patent broadly covering a method of pumping coal with water was granted to W. C. Andrews. His pilot plant was constructed on what is now the site of the New York Public Library in Manhattan. His process was applied to pumping coal mine waste back into the worked out portion of coal mines. On October 26, 1967, the world's first long distance iron ore slurry line was put into service by Savage River Mines. The commissioning of this 5.0 million dollar installation climaxed three years of development, testing, and construction and proved the Company's faith in pioneering this unique transportation method for iron ore. This paper will discuss some of the more pertinent items in connection with that three- year period. Also to be discussed will be the operation of this line during the past eleven months.

Jan 1, 1968

By William H. Mount

Since the late 19405, St. Joe has operated rubber-tired, trackless mining equipment underground in its Southeast Missouri Lead Belt operations. At first, the trackless equipment was operated in conjunction with rail haulage equipment in the room-and-pillar operations, but was to later replace rail haulage completely. The first pieces of equipment to travel on pneumatic rubber tires were short-haul shuttle cars of 12-ton capacity hauling rock from the heading to the mainline railroad. Early-model drill jumbos were the next pieces of production equipment to be carried on rubber, along with mobile slusher ramps. Mobile diesel equipment, in the form of conventional rear-dump trucks, made its appearance underground in the early 1950s, introducing the era of relatively high-speed mobile equipment as compared to the electrically powered shuttle cars. Haulage distances for rubber-tired vehicles were no longer dictated by trolley lines and trailing cables and tires were subjected to increasingly severe applications. St. Joe's first completely trackless mine, the Hayden Creek Mine, was opened in 1952, employing rubber-tired drill jumbos, electric shuttle cars, and for the first time, an articulated diesel truck consisting of the tractor unit of a conventional earthmoving scraper and a rear-dump rock wagon. Those machines rolled on the first true earthmover tires to be used underground by St. Joe. The articulated truck concept proved to be very successful, and constitutes an In- creasing portion of the underground haulage today.

Jan 1, 1975