Search Documents

By M. T. Simnad, G. Derge, Ling Yang

A method is described for using radioactive tracer for the direct determination of ionic mobility in a molten electrolyte. The ionic mobility of Fe" in silica-saturated iron silicate is found to be 0.0009 (*0.0002) cm2 sec ' volt L at 1250°C. eLECTROCHEMICAL studies', ' of molten iron eE oxide and iron silicates have shown some ionic conductivity at all compositions. The current efficiency in electrolysis increases with the concentration of silica to a maximum of 90 pct at about 34 pet SiO,. In the silica-saturated melts the transport number of ferrous ions is near unity, indicating that

Jan 1, 1957

By W. J. Kroll

W. J. Kroll (Belgium)—Those who are acquainted with the metallurgy of our forefathers may have occasionally a good time when glancing at recent publications in which aged discoveries are unconsciously reported as novelties. We know very well, that oxygen blowing of iron has been described by old Bessemer. The author of the present article is, however, not aware of the fact that the process he describes, the fused salts scrubbing, was already used in the middle of the last century by St. Claire Deville in his attempts at making higher-purity aluminum from raw AlCl3 by sodium reduction. The same fact escaped the three investigators to whom the author refers. The technical grade AlC13 produced by St. Claire Deville from impure oxide, chlorine, and carbon (Oersted process) was contaminated with Sic4 and FeC13, which he removed on an industrial scale by various methods.' He sublimed, for instance, his chloride in contact with iron nails, or aluminum chips, or in hydrogen, which reduced the FeC13 to the less volatile FeCl2. He used also alkali-alkaline earth chlorides as a solvent for A1C13 and FeC13 in presence of iron as a reducing agent, and sublimed his purified AlC13 from solvent salts. The successors of Deville used also zinc or lead as a reducing agent. These methods were later used currently for the purification of BeCl2 and for collecting this compound in a salt bath, suitable for fusion electrolysis. More recently, the same Deville process has been described as applied to the purification of ZrCL4, as part of a method of extraction of ZrCL4 from silico zirconium, which later was reacted with FeC12 in a separate part of the equipment. According to the patent referred to3 the ZrCL4 is dissolved as a gas in a carrier salt such as alkali-alkaline earth chloride, from which it can be reclaimed in a purified form by distillation. A bath of NaCl/KCl is recommended in the specifications. The FeC12-FeC13 go in the salt solution in which raw ZrCl4 is introduced by bubbling, while Sic4 and Tic4 pass through the bath and escape in the atmosphere. purification by this salt-solvent method is thus well described. It may be worth while insisting on some minor details about which the author did not bother too much. One of these concerns the material of construction for the container. If iron is used, and if no other reducing agent is added, then it is the iron of the pot that acts as a reagent in the breakdown of FeC13 to FeCl2, and corrosion can be expected. This shows the importance of using extraneous large surface-reducing agents, of which there is a choice. Zir-

Jan 1, 1963

A. A. CENTER*—This paper reminds me of the beginning of the work of the Electrolytic Zinc Company of Australasia. Early work for this Company, as some of you may know, was done at the Bully Hill Plant in California. After working there for some time Herbert Gepp, now Sir Herbert, came to the Anaconda Co. plants in Montana where I met him. He spent some months there, in fact almost a year if I remember rightly. That was when we were breaking in the new electrolytic zinc plant at Great Falls, Montana. From there he went back to Australia and started in on the plant there. I believe they had an original plant of about 20 tons per day of cathode zinc. We heard from them for some time, until they were able to go along on their own, and they have done very well ever since as you have heard. Their practice, (the flow sheet, the leaching practice), has been quite different as reported in the paper and apparently they are still following that practice to some extent. While the earliest work on selective flotation was done down in Australia, the big companies there, strange to say, were far behind the American companies in taking it up; and it is only in comparatively recent years they have gone to the alkaline circuit and dropped out thereby more of their iron and lead. The zinc plant now is up to a capacity of 100,000 tons a year and I believe that may be notched up to about 105,000. T. H. WELDON*—I would like to ask

Jan 1, 1950

By F. F. Poland

The purpose of this paper is to describe the recent applications and improvements made in the process and equipment for the recovery of metallic zinc from secondary metals by means of high temperature electric resistor furnace distillation. The process and high temperature furnace, as developed by Revere Copper and Brass Incorporated, Research and Development Department, was described in a previous paper. † Since the publication of that paper the process and equipment have been licensed to others. Consequently its field of application has been expanded, particularly for the treatment of scrap brass, galvanizers dross and scrap zinc. Other applications are being considered, particularly the melting of metallic titanium and special alloys requiring a controlled atmosphere. Consideration is also being given to modification in design that would allow the melting of copper cathodes for the production of oxygen-free and electrolytic tough pitch copper shapes without the necessity of blowing and poling. In the design of a furnace for melting copper cathodes it is intended that the fundamental principle of charging the solid material into a large pool of molten metal through a double door charging vestibule as shown in Fig 3 of the previous paper, † would be adhered to and, in addition, either dehydrated and desulphurized producer gas or commercial nitrogen, that is, approximately 96 pct nitrogen, 2 pct hydrogen 2 pct CO, also dehydrated, would be used to provide a protective atmosphere for the resistors and to flush out more soluble gases from the molten copper. The operation of a small unit producing approximately 1000 lb of copper per hr has shown that the commercial nitrogen will allow the production of tough pitch electrolytic copper when the metal is transferred from the meltdown unit contemplated to a special type induction unit where the oxygen absorption and temperature can be controlled. Standard practice in treating low grade scrap brass has been to oxidize the zinc by blowing air through the molten metal. This operation results in the recovery of approximately two-thirds or less of the zinc content of the brass in the form of an impure zinc oxide having only a fraction of the value of the zinc in metallic form. The balance of the zinc is lost to slag, fume and drosses. Fig 1 shows the revised flow sheet of the process for the treatment of scrap brass. For this application and as shown on the flow sheet a low frequency induction furnace has been substituted for the Wilkins-Poland type as a melting unit. This type of furnace has been found the most suitable for the purpose as will be shown by the following discussion. Serap Brass The melting of refinery scrap brass preparatory to distillation presents a melting problem quite different from the usual melting of brass mill scrap for recasting because refinery scrap is a heterogeneous mixture of alloys each having different melting and boiling points, and coated with a variety of corrosion products and foreign materials. In addition, brass and copper plated pieces of sheet iron, stainless steel, ceramic materials, and others are present that do not melt except at temperatures above the boiling point of the liquid bath. In the previous paper it is noted that difficulty was encountered in the melting of refinery grade scrap brass without excessive loss of zinc by volatilization and that 5 to 10 pct razorite flux was used to alleviate this condition. While this flux was successful in preventing the excessive loss of zinc by volatilization it interposed a low heat conductivity layer between the source of heat and liquid charge and resulted in lowering the melting rate of the furnace. This same problem presents itself in all types of furnaces in which the metal is heated by radiation and conduction from above the charge. It has been found in melting this type material that the melting rate per hour or per square foot of hearth area

Jan 1, 1950

By F. F. Poland

S. ROLLE*—As one who has been privileged to read Mr. Poland's paper before its publication, I wish to express high praise for it and the record which it gives of the work done by the Research and Development Department of Revere Copper and Brass Inc. in developing a satisfactory furnace for the recovery of metallic zinc from secondary metals by distillation. I have also had the opportunity of studying the operation of the furnace when running on scrap brass at the Detroit plant of Revere, and I can therefore say from knowledge gained first-hand that the unit is efficient and economical when used in conjunction with distillation. However, when I read what Mr. Poland has to say in reference to the possibility of using the furnace for melting copper cathodes for the production of oxygen-free and tough-pitch copper shapes, I am constrained to be somewhat skeptical. No doubt the furnace can readily be modified so as to make it possible to melt cathodes, but that is only a part of what is required to produce refinery shapes. Because of its construction the atmosphere in the furnace is highly reducing and even without protective gases such as nitrogen the copper cathodes which are

Jan 1, 1950

By Douglas J. Harvey

The surface tension of lead-tellurium alloys (in the range 0 to 6.70 at. pct Te) ad lead-arsenic alloys (in the range 0 to 10.53 at. pct As) has been examined by the maximum bubble pressure method. The surface tension of high purity lead can be expressed over a range of temperatures (M.P. to 750°C) by the relationship = 512 — 0.133t. Arsenic and lellurium were both found to be surface active in lead. The surface excess concentration at 700°C was .found to be constant at 0.74 x 10-10 moles per sq cm for tellurium. The surface excess of arsenic at 700°C varied between 0.26 x 10-10 moles per sq cm at 0.16 at. pct to 1.5 x 10-10 moles per sq cm at 8.3 at. pet. The surface tension of lead has been investigated sporadically over the last 90 years. The first recorded study was made by Quincke1 who used a rather crude application of the drop-weight method. Hogness2 obtained the first reliable value for the surface tension of lead by measuring the pressure necessary to force the liquid metal from the end of a small capillary of known radius. Hogness gives the empirical formula: ?(surface tension)= 444 - 0.077 (l-327) which describes the relationship between surface tension and temperature ("C); This work was followed by that of Bircumshaw3 who applied the two-capillar maximum bubble pressure method of Sugden.4 The values published by Bircumshaw are in good agreement with those found by Hogness. Matuyama5 examined the surface tension of lead by the drop weight method. However, the values found are somewhat higher than those previously reported. More recent investigations by Greenaway6 and by Melford and oar' have resulted in data which are not in close agreement, but which are well within the expected range at most temperature levels. The study of the surface tension of lead alloys began with Drath and sauerwald8 who examined the lead-bismuth system. They found that the surface tension values of the alloys in this system deviated only slightly from the ideal mixture rule. Matuyarna5 examined the lead-antimony system. Bircumshaw the lead-tin, and the lead-indium system was studied by Hoar and Me1ford.10 The results of these investi- gations are summarized in Fig. 1. It may be seen that the data vary only slightly from the ideal mixture rule. As none of the metals studied and reported in the literature has a very interesting effect on the surface tension of lead,*the next logical step might be to examine the effect of metals of low solubility or nonmetals having some liquid solubility. Baes, and Kellogg11 have pointed out that the elements most likely to be surface active in liquid metals are ones of limited solubility in the liquid state and possessing weak intermolecular bonding forces in the solid state. Therefore, Group V, VI and VII nonmetals are most likely to be surface active. It was decided to examine the effect of a borderline metal, arsenic, and a nonmetal tellurium. Arsenic forms a eutectic with lead having a melting point of 290°C and a composition of 6.9 at. pct As.13 Pure arsenic sublimes when heated above 610°C. Even though alloying with lead lowers the vapor pressure, fumes containing arsenic are evolved at a very noticeable rate when lead-arsenic alloys are heated above 650°C. Tellurium raises the liquidus temperature of lead sharply to 904°C,14 the melting point of PbTe (lead-telluride). The solid solubility of tellurium in lead was determined by Greenwood and worner15 to be 0.0007 at. pct at room temperature. EXPERIMENTAL METHOD Surface Tension Measurement—The two capillary maximum bubble pressure method for measuring surface tension developed by Sugden,4 and used later

Jan 1, 1962

By C. A. Winkler, V. Hospadaruk

PREVIOUS papers from this laboratory have discussed the effect of chloride ion on the cathode polarization during electrodeposition of copper from copper sulphate-sulphuric acid electrolytes, in the presence and absence of gelatin. The steady state polarization'" was found to decrease sharply and pass through a minimum with increasing chloride ion concentration in the presence of gelatin. The minimum shifted to higher chloride ion concentrations and to higher polarization values with increase in current density or gelatin concentration, while an increase of temperature shifted the minimum toward lower halide concentrations and lower polarizations. Since these observations were made in acid-copper sulphate electrolytes that contained no other addend than gelatin, there was obviously the possibility that they were not applicable to deposition of copper from commercial electrolytes that contain a variety of other substances in relatively small amounts. In particular, it was of interest to determine whether the presence of arsenic, antimony, or bismuth in the electrolyte would materially alter the behavior. Experiments have now been made under a variety of conditions with systems containing these cations, and the results are summarized in the present paper. Experimental Polarization measurements were made at 24.5oC in a Haring cell in the manner described previously.' Electrolytes were made with doubly-distilled water, and contained 125 g per liter of copper sulphate and 100 g per liter sulphuric acid, both of reagent grade Eimer and Amend gelatin from a single stock was used throughout. Chloride ion was introduced as reagent grade sodium chloride, and arsenic, antimony, and bismuth by dissolving the chemically pure metal in hot concentrated sulphuric acid and adding appropriate amounts of the solutions to the electrolyte. Each cathode, of 1/16-in. thick rolled copper, was first etched in 40 pct nitric acid and washed thoroughly with distilled water. The surface was then brought to a standard condition4~9 by electrodeposition from an acid-copper sulphate electrolyte containing no gelatin, at a current density of 3 amp per sq dm for 30 min, followed by deposition at a current density of 2 amp per sq dm for l hr. As in previous studies, the cathode polarization eventually attained a steady-state value (15 to 75 min) such that further change in polarization did not exceed 0.2 mv per min. The polarization values recorded are those for the steady states. "Excess weights" were determined with arsenic and antimony present in the electrolyte, as the difference between the weights of the deposits obtained in the presence of these cations and those obtained in their absence, with the two cells connected in series. When gelatin was present along with the arsenic or antimony, it was also added to the electrolyte in the cell in series. Results and Discussion The results of the study are summarized in Figs. 1 to 6. From Fig. 1, top, it is evident that the presence of arsenic or antimony alone results in an increase of polarization, while bismuth alone causes a decrease. The presence of gelatin (25 mg per liter) rather drastically modifies all three cation effects, as indicated in the lower panels of the same figure. The addition of chloride ion, when no gelatin is present, causes comparable decreases in polarization in the presence of antimony and bismuth, but a relatively larger decrease when the electrolyte contains arsenic. It is interesting to note that the decrease in polarization brought about by addition of chloride when both arsenic and antimony are present parallels the behavior with arsenic alone, while the polarization in the electrolyte containing the cation mixture, without chloride added, corresponds to that for an electrolyte containing only the antimony cation. Similarly, the polarization at zero concentration of chloride in electrolyte containing arsenic and bismuth is that corresponding to an electrolyte containing arsenic alone. From Figs. 3a, 4a and 4b, it is clear that, in the presence of gelatin at a level of 25 mg per liter, the effect of chloride in the presence of arsenic and antimony, or a mixture of the two, becomes quite analogous to that observed in the absence of added cations. When both bismuth and gelatin are present (Fig. 5), the decrease in polarization with increased chloride concentration is virtually absent. This is perhaps a reflection of the large decrease in polarization brought about by the bismuth itself in the presence of gelatin. The shifts of the minimum in the polarization-chloride concentration curves brought about by changes of temperature (Fig. 3b), gelatin concentration (Figs. 3c and 4c) and current density (Fig. 3d) when the metal cations were present are all similar to the corresponding shifts observed in their absence." The approximately linear "excess weightv-anti-mony concentration relation recorded in Fig. 6 would seem to indicate that antimony is codeposited with copper to a considerable extent. On the other hand, only very limited amounts of arsenic appear to be adsorbed or codeposited.

Jan 1, 1954

By C. F. Baes, H. H. Kellogg

The effect of dissolved sulphur on the surface tension of liquid copper has been measured by a sessile-drop method at 1120°C. Sulphur is highly "surface active" in liquid copper; the surface tension lowering is about 650 dynes per cm for a sulphur content of 0.6 pct. The degree of adsorption of sulphur on the liquid copper surface has been calculated, and various models of the surface layer have been tested against the results. THE science and technology of surface chemistry and physics at room temperature are relatively advanced, and the engineer possesses a background of information that allows him to predict and control many phenomena—such as frothing, emulsifica-tion, wetting of solids by liquids, flow through capillaries, adsorption, mineral flotation, penetration of porous bodies by liquids—which are related to the behavior at interfaces. Surface phenomena in high temperature systems are probably of equal importance to the metallurgist and ceramist, but at present are incompletely understood. Frothing of liquid slags, penetration of refractories by liquid metals and slags, infiltration of powder metallurgy "skeletons" by liquid metals, bonding of metals to ceramic oxides in the manufacture of "cermets," wetting of one metal by another for purposes of soldering and welding, are but a few of the many phenomena of metallurgy that are controlled by surface behavior. Concerning the most elementary of surface properties—the gas-liquid surface tension—the existing data on liquid metals are inadequate. For the surface tension of "pure" metals the results of different investigators differ by 10 or 20 pct. The role of surface-active agents in liquid metals is relatively unknown, and it is not unlikely that the discrepancy in the values for the surface tension of pure metals is due to the presence of traces of surface-tension-lowering impurities in the samples. Based on analogy to room-temperature systems, the highly surface-active impurities in liquid metals should be elements or compounds of limited solubility in the liquid metal and possessing considerably weaker in-termolecular bonding forces than the metal itself. The nonmetals of the V, VI, and VII groups of the periodic table might be expected to act in this way. The experimental work in this paper represents a study of the surface tension of pure liquid copper in hydrogen at 1120°C, and the effect of dissolved sulphur (which is a strongly surface-active agent in liquid copper) on the surface tension of copper. The Gibbs equation has been applied to the results and an attempt made to correlate the surface tension behavior with two models of the interfacial layer. The sessile-drop method for surface-tension measurement at high temperatures which was used in this investigation has been described by several investigators.1,2 It involves the measurements of the dimensions of a stationary liquid drop on a horizontal surface. From these dimensions and the liquid density, the surface tension of the liquid may be calculated either by means of various approximate formulas, or more accurately by means of the Bash-forth and Adams tables.- or liquid drops which exhibit a contact angle greater than 90°, by far the simplest dimensions to measure are those indicated in Fig. 1, i.e., the diameter of the maximum horizontal cross section (2X) and the maximum height (Z) above this plane. In order to calculate the contact angle and the volume of the drop, the diameter at the base of the drop (2a) and the total height (h) also must be measured. Upon investigation of the literature, the authors failed to discover a concise statement of the accuracy of the method when used in conjunction with the Bashforth and Adams tables, hence a careful examination of the tables was made and the curve shown in Fig. 2 was constructed. The "error factor," plotted as the ordinate, is the factor by which the

Jan 1, 1954

By Walter R. Hibbard, Harold Margolin

The effect of ten ternary additions on the aging of a Cu-Ag alloy was measured by X ray, microstructure and hardness. A supersaturated copper-rich transition structure was found. The effect of the ternary element was related to differences between transition and precipitate lattice parameters and analogies with solution and strain hardening. IN addition to the prerequisite of diminishing solid solubility with falling temperature, the theory of coherency hardening1 proposes that the principal source of hardening during precipitation is strain caused by coherency between the matrix and precipitate. For a given system greater coherency hardening would result from lengthening the period of coherent growth and/or increasing the number of nuclei, other things remaining equal. However, the hardness change during aging is a function of a number of phenomena in addition to coherency hardening, such as dispersion hardening, loss of coherency, solute depletion, matrix recovery or recrystal-lization, coalescence, and their relative time sequences. The present investigation was undertaken to study the effect of ternary additions on the age-hardening of Cu-Ag alloy. For this purpose a series of alloys were made containing as ternary constituents Mg, Al, Si, P, Mn, Ni, Zn, As, In, and Sb. These elements were added to a master 5 wt pct Ag in Cu alloy in such amounts as to obtain alloys listed in Table II containing the following approximate atomic percentages: 96 pct Cu, 3 pct Ag, 1 pct ternary addition. A 97 atomic pct Cu, 3 atomic pct Ag alloy was used as a comparison standard. There have been numerous investigations of age-hardening in Cu-Ag alloys2-lo but few of ternary Cu-Ag alloys. Pfister and Weist" found that 1 wt pct Ni reduced the solubility of Ag in Cu above 600 °C and that the rate of precipitation was slower than in polycrystalline Cu-Ag alloys of similar silver content. More recently Hodge, Jaffee, Dunleavy, and Ogden12 investigated the effect of ternary additions of Mg, Li, P, Cd, Zn, Zr and Be on strength properties of Cu-Ag alloys. Mg, Cd, and P were found to increase strength in the aged and cold-worked condition. Experimental Procedure Charges weighing 7.5 lb were melted in a closed carbon crucible under a reducing atmosphere* of nitrogen and hydrogen. A Durville-type casting procedure with a hot-top arrangement was used to obtain a sound casting, 2x2x43/4 in. Prior to rolling and annealing of the ingots, a trial solution anneal of rolled sections of the hot-top portions indicated that at 780°C melting was avoided except for the Cu-Ag-Sb alloy. This alloy could not be produced as a single phase within the limits of temperature control. i 3" to 5oC, since melting occurred at 64O °C, and below this temperature precipitation was

Jan 1, 1952

By B. B. Kunkle

The history of this refinery has been one of expansion. It now has the capacity to produce 240,000 tons of cathodes annually. A general flowsheet and descriptions of the plant layout, operations involved, and equipment used at one of the world's largest and most modern electrolytic copper refineries are presented. THE El Paso copper refinery of Phelps Dodge Refining Corp. was originally constructed by the Nichols Copper Co., in association with Phelps Dodge Corp. and the Calumet & Arizona Mining Co., in order to refine anode copper produced at the smelters of the two latter companies. Initial production was obtained from the plant in January 1930 and its annual refining capacity was 100,000 tons of anodes. In order to keep pace with Phelps Dodge Corp.'s increasing copper production in the Southwest, it became necessary in 1937 to increase the El Paso plant's refining capacity to 160,000 tons of cathodes annually. This was accomplished by adding two sections to the electrolytic tank house, increasing the number of anodes placed in each commercial electrolytic tank from 33 to 37, and making changes in the dc circuits which made it possible to put three generators on each of the two circuits instead of two, thus increasing the amperage on each circuit from 10,000 to 14,800 amp. The capacity of the two furnaces from which refined shapes were cast was increased by raising the sidedoor bays on the furnaces 6 in. An increase of 70 pct in the productive capacity of Phelps Dodge Corp.s Morenci Branch in 1942 again made it necessary to expand refining capacity. In order to accomplish this, Defense Plant Corp. set up a project to increase the capacity of the El Paso plant to 240,000 tons of cathodes annually. This project consisted of enlarging the tank house approximately 50 pct, the construction of another wire- bar furnace, and corresponding increases in other departments where necessary. The engineering work on this expansion was begun in March 1942. Actual construction was under way by August 1942, and the work was completed by March 1944. These additional facilities were purchased from Defense Plant Corp. by Phelps Dodge Refining Corp. in August 1949. The plant is in El Paso about eight miies east of the center of the city and near Highway 80 and the main lines of the Southern Pacific and Texas & New Orleans railroads. The plant site covers approximately 494 acres of company-owned land that is ideally adapted for its use, being well-drained sandy soil and having enough slope so that a minimum amount of excavation was required when the plant was constructed. There is still ample room on the plant site for any future plant expansion. The plant is constructed on four different ground levels and so arranged that the unrefined copper is unloaded on the highest level at the north side of the plant and the refined copper is shipped out from the lowest level on the south side of the plant. The receiving or unloading platform, weighing and sampling rooms, main floor of the tank house, acid and condensate storage tanks, and the slimes and copper sulphate plants are on the first or highest level. The tank house basement, yard scales, charging and furnace bays, balloon flue and stack, brick-storage building, substation and power house, boiler feedwater treating plant and pump house, water storage tanks, and change houses are on the second level. This second level also contains ample yard area for setting-up furnace charges, and for storage of custom scrap, cathodes, scrap anodes, blister, coke, and poles. The casting wheels, inspection conveyors, cathode shears, wire-bar scalping machine, slag

Jan 1, 1952

By T. J. Woodside

Prior to 1927 the lead blast furnace charge at El Paso consisted principally of direct-smelting carbonate ores, very low in zinc, and the resulting slag seldom carried more than 4.0 pct. With the exhaustion of the mines in Northern Mexico which supplied these ores, they were supplanted with a much smaller tonnage of sulphide concentrates containing appreciable amounts of zinc, and the zinc content of the slag rose to 10.0 pct. The Anaconda Company's slag fuming plant at East Helena, Montana, had then been in successful operation for several years, and it was immediately recognized that, while at that time the production of high zinc slag was small, if the grade held, a plant for the recovery of zinc from the accumulated slag might some day be practical. The grade not only held but became increasingly higher so that by 1946 suffcient slag had been accumulated to warrant the construction of a fuming plant regardless of future slag production from the blast furnaces, and with the removal of Government restrictions on construction at the end of the war the project was undertaken. The general design of the plant follows that at Bunker Hill, with waste heat boiler, unit coal pulverizers and even more extensive instrumentation and automatic control. The area around the lead blast furnaces is rather congested, being cut off from the nearest feasible site for the fuming plant by the copper plant, so that the most practical route for hot slag transfer is through the converter aisle. For this reason and also to make use of the existing converter cranes to serve the fuming furnace, an unused reverberatory at the north end of the converter building was dismantled and the fuming furnace and boiler located in its place. A flue at right angles to the furnace and boiler runs northward to the U-tube coolers and baghouse (Fig 1). From the bag-house a steel flue runs eastward to an existing and long unused 300 ft con- Crete stack. The coal handling system and de-leading plant lie north of the furnace and east of the cooling tubes and baghouse. The furnace is conventional, 8 X 21 X 33 ft high inside and completely water jacketed (Fig 2). There are 21

Jan 1, 1950

By T. J. Woodside

A. E. LEE*—One question of the flue leading to the tube coolers. What gas velocity is maintained to prevent settling of the finely divided fume ? T. J. WOODSIDE (author's reply)— 30 fps. Of course some fume settles out, but is immediately carried away by the screw conveyors. H. R. BIANCO —How effective are the soot blowers ? Do you have to use any hand lancing? T. J. WOODSIDE Only one point, which is right at the top of the economizer and which the soot blowers do not reach, we occasionally hand lance. But everywhere else the soot blowers have been very effective and no hand lancing has been done. L. V. DAVIDSON*—Do you have considerable variation in the lead content of the fume collected if the lead is higher, and is there greater tendency for the fume to stick on the boiler tubes ? T. J. WOODSIDE—There is very little variation in the lead content. From 5 to 7 pct is the widest range variation we have had and we have noticed no difference in the behavior of the fume. C. R. KUZELL—Mr. Woodside has been quite generous with data pertaining to metal and fuel economics. I think he stated that the coal consumption of the furnace was 21/10 21/10 for a pound of zinc recovered. I take it that that is the gross coal input to the furnace. I wonder what the net fuel consumption in terms of coal might be after crediting the fuel equivalent of the waste heat steam recovered? T. J. WOODSIDE—The fuel value of the waste heat steam is approximately 42 pct of the heat input to the furnace. A very large part of the heat, of course, goes out in jacket water—44 pct. A. D. TERRELL*—I would like to know how much lead is in the deleaded material. T. J. WOODSIDE—It is a little less than 2 pct now.

Jan 1, 1950

By Peter R. Drummond

THE final casting of refined copper has been re-J- stricted for generations by the following sequence of operations: Filling the reverberatory furnace, melting, skimming, blowing or flapping, and poling. The hoped-for 24 hr cycle, producing 300 tons or more, has been taken up largely with the necessary bat time-consuming tasks of cleaning the bath, sulphur elimination, and in turn removal of excess oxygen to produce tough-pitch copper. Incidental to comparatively slow melting under combustion gases, copper oxides react with the furnace lining, and the slag so-formed must be completely recycled. The three-phase arc furnace has eliminated some of the cycle stages, and telescoped the remainder into a continuous operation. Electrical energy, supplied to graphite electrodes enclosed in high grade refractories, rapidly melts copper cathodes and sustains a stream of metal, containing approximately 0.01 pct oxygen, without contamination from fuel. The arc was struck on the first large electric furnace for melting copper in the United States on April 13, 1949. The earliest use of this type of furnace was at Copper Cliff, Ont., in 1936, and an admirable description of their installation has been published? Copper, melted in the Baltimore furnace, is used to cast billets, and the installation differs somewhat from the Canadian, as will be described. The arc furnace is a heavy-duty, three-phase furnace, holding 50 tons, the general outline of which appears on Fig. 1. The steel shell is 15 ft ID with a bottom radius of 14 ft 2 in. The roof, separate and distinct from the body, consists of a 15-ft water-cooled, cast-steel ring of the same outside diameter as the furnace. The center line of the furnace lies 9 ft 6 in. from that of the trunnions, permitting a 5" backward tilt for skimming, and a 40" maximum nose tilt forward for complete draining. Normally, the furnace overflows by displacement, and the use of the forward tilt arrangement is restricted to covering charging delays. The charging slot, 3 ft 8 in. x 5 in., lies on the north center line, the tap hole on the south, and the 30x30 in. skim door 45" to the west of the slot. The original 20-in. graphite electrodes were replaced with 14 in. in December 1949. Three conventional direct current winch drives, governed by electrical controls, position each electrode which has individual mast supports and counterweights. An independent circulation supplies cooling water for the electrode glands, the roof ring, charge slot, and the skim door frame. Arc Furnace Refractories Hearth: Fused-in monolithic bottoms had been used in copper arc furnaces, installed prior to April 1949. These consisted of thin layers of periclase, successively fused in place over preliminary brick courses. Heat was obtained from the arc, using a T-like arrangement of broken electrodes resting directly on the periclase to be fused. The operation, taking weeks to perform, was very expensive. The chemically-bonded magnesite-brick bottom, installed at Baltimore, was the first of its kind and a radical departure from previous practice. It consists of a 1 to 6-in. layer of castable refractory laid on the steel shell, modifying it to a 12 ft 2 in. bottom radius. Two courses of 9x2 % -in. fireclay straights and keys follow. The third course is made of 9-in. magnesite blocks of special shape to form circles of an inverted arch. It was started by a four piece keystone with skew-backs forming the outer course. The fourth course also started on a central keystone, or button, of four 90" segments, 12 in. diam x 13 Vz in. deep, and continued with 13%-in. blocks. Skewbacks at the shell completed the course to produce a horizontal surface for the side walls with a single course of No. 2 arch fireclay against the steel. Dry chrome-magnesite cement was brushed over each course after laying, and a 1-in. expansion space between the brick and the shell was filled with the same mixture. The total bottom thickness, excluding the castable material, was 5 in. of clay plus 22% in. of chemically-bonded magnesite. Tap Hole: A 5-in. OD and 3-in. ID silicon-carbide tube constitutes the tap hole and is set tangential to the upper course of the furnace bottom. Molten metal fills the tube when the furnace is level and filled to capacity. Side Walls: The lining, against the shell, consists of a 9x4Y2x3 in. soldier course of fireclay, using straights and No. 1 arches to turn the circles. A second soldier course of 9x4'/2x2'/2-in. fireclay was laid in a somewhat similar fashion. Three courses of 13Y2x6x3 in. and 9x6~3 in. of final magnesite, laid flat, completed the lining, using Nos. 1 and 2 keys to turn the circles. Cardboard spacers were placed between every two bricks in horizontal courses, and a thin coat of chrome-magnesite cement filled the joints between the firebrick and magnesite. A sprung-arch spanned the skim door with jambs of suitable magnesite shapes. Charge Slot: The slot is 3 ft 8 in. wide x 5 in. high. A silicon-carbide sill of special shapes has a 30" slope to allow cathodes to slide easily into the bath. The original arch was flat, and composed of Nos. 1 and 2 wedge magnesite with a 6-ft radius. It projected 5 in. over the sill, and, being a flat arch, gave an 18 15/16-in. opening between the inner edge and the metal line. The whole assembly was later raised 9 in., and the flat arch replaced with an arch, the lower edge of which maintained the 5-in, width from the outer to inner edges as shown in Fig. 2. A water-cooled, cast-copper jacket protects the steel shell behind the slot.

Jan 1, 1952

By G. Osuch, G. Derge, G. M. Pound

Using a new dternating-current potentiometer circuit and a specially designed four-terminal cell, the specific conductance of molten Cu2S-FeS mattes was measured as a function of temperature, from the liquidus to 1500°C, over the complete range of composition. The high conductivities, about 1500 ohm-I cm-l for FeS and 100 ohm-l cm-l for Cu,S, indicate that the conduction is electronic rather than ionic. Molten FeS has a negative temperature coefficient of specific conductance, resembling metallic conduction. Molten Cu,S has a positive temperature coefficient, resembling semiconduction. The binary roughly follows an additive rule of mixtures with respect to both magnitude and temperature coefficient of specific conductance. Metallic bonding in the liquid is postulated to explain these phenomena. MUCH has been learned in the past about the nature of liquids and the ionic or molecular species in solution by means of electrical measurements. Thus, dielectric constants','2 have given information about molecular liquids such as water and benzene. Measurements of dielectric constant usually are impossible in electrically conducting liquids, such as aqueous solutions of ionic salts and molten ionic salts. However, measurements of electrical conductance and ionic transference have provided much knowledge about the latter systems.a-" In recent years, the ionic nature of certain molten metallurgical slags has been established by Derge and Martin7 through electrical conductance and electrolysis measurements. Chipman, Inouye, and Tom-linsonq ave studied the electrical conductance of molten FeO and report a high specific conductance of about 200 ohm-' cm-' (compared with 4 ohm" cm-' for an ordinary ionic liquid such as molten NaCl) and a positive temperature coefficient of conductance. They interpret these results in terms of p-type semiconduction by analogy to the situation in solid FeO.Y imnad and Derge" have studied cell efficiency in the electrolysis of molten FeO-SiO, systems and conclude that ordinary ionic conductance increases with SiO, content. Very recently, interest has been revived in the electrical conductance of liquid metals and liquid metallic solutions. Scala and Robertson1' report a close resemblance between the liquid and solid states with respect to thermal, structural, and compositional relationships. Molten sulphides have not received a great deal of attention. Bornemann and von Rauschenplat" measured the specific conductance of molten Cu2S as a function of temperature with a four-terminal cell using direct current. A high specific conductance and a positive temperature coefficient were found in that investigation." Using a two-electrode apparatus, Savelsberg" electrolyzed various molten sulphide mixtures. He concluded that pure molten Cu,S and FeS were electronic conductors but that the mixtures exhibited some ionic conduction. In the present investigation, the specific conductance of the industrially important Cu-Fe sulphide mattes was measured as a function of temperature and composition in order to investigate the mode of electrical conduction and the structure of these molten mattes. An alternating-current circuit was used to eliminate the effect of any possible electrode reactions. Apparatus The Conductance Cell: Due to the high specific conductance of the systems studied (10' to 10" ohm-' cm-'), the classical two-terminal cell and Wheat-stone bridge apparatus could not be used. A four-terminal cell was developed in order to eliminate lead resistance, and an ac potentiometer circuit was designed to give rapid and sufficiently accurate measurements of the cell resistance. A diagram of the conductivity cell is given in Fig. 1. The molten matte is contained in a dense alundum crucible, and spectrographic graphite rods that dip into the molten matte serve as the four conductance terminals. Two of the graphite rods on opposite sides of the cell serve as current-carrying leads, and the other two graphite rods are null-current probes that detect the potential drop across the cell. These graphite rods are contained in silica tubes, and the lower constricted portions of the two silica tubes define the column of liquid whose electrical resistance is being measured. The electrical resistance of the broad ex-

Jan 1, 1956

By L. J. Howell, H. H. Kellogg

AN a previous paper' the phase diagram and vapor pressure of melts in the systems NaC1-ZrCl,, KC1-ZrCl,, and NaC1-KC1 (1:1 molar)-ZrC1, were reported. This note supplements the earlier paper with the results of electrical conductivity measurements on NaC1-ZrC1,and NaC1-KC1 (1:l molar)-ZrC1, melts. The design of the conductivity cell is shown in Fig. 1. Tungsten electrodes, A, were sealed into the Pyrex cell, C. That portion of the electrodes in contact with the melt was covered with a tight-fitting platinum cap. The electrodes were sur-

Jan 1, 1960

By Edna A. Dancy, Gerhard J. Derge

Jan 1, 1963

By K. A. Svanstrom, W. R. Opie

Problems associated with deposition of titanium infused chloride baths using TiCl4 as a feed material are reviewed. A potentially workable cell design using Alumdum diaphragms is discussed. Problems inherent to diaphragm-type cells are emphasized and experiments described which led to the development of a cell without a diaphragm. INVESTIGATORS assigned the problem of developing a commercial electrolytic process for making titanium metal have found that they are faced with the difficulty of overtaking rapidly improving magnesium and -sodium reduction processes. The ultimate goal must be a simple process that can be conducted with low-cost raw materials in equipment that is inexpensive to build and operate. This paper deals with some work of a preliminary nature conducted by personnel of the Research Laboratories, National Lead Co., Titanium Division. Many others have reported on the general subject of depositing titanium from fused salt electrolytes. A partial bibliography is attached. PRIMARY CONCEPTS Anyone attempting to deposit titanium metal from fused chloride electrolytes using TiC14 as a source material is faced with at least the following problems: 1) Getting the titanium into solution in the bath. 2) Controlling oxidation and reduction reactions associated with multiple valency of titanium, which result in low electrical efficiency. a) Prevention of dichloride oxidizing to trichloride and trichloride to tetrachloride at the anode. b) Prevention of trichloride from being reduced only to dichloride at the cathode. 3) Prevention of metal formation away from the cathode thru disproportionation of titanium dichloride to satisfy the equilibrium. 3 TiCl2 == 2 TiCl3 Ti [I] 4) Protection of reduced chlorides in the bath from reaction with oxygen from the bath container or air. 5) Removing from the bath the deposited metal formed without allowing it to become contaminated with oxygen or nitrogen. 6) Selecting cell materials of construction which will not contaminate the metal product or cause cell inefficiencies. EARLY EXPERIMENTS The initial attempts made to electrodeposit titanium from fused chloride baths using TiCl4 as a source material indicated that TiCl4 was essentially insoluble in molten chlorides of alkali and alkaline earth metals. If, however, the TiCl4 was introduced close to a nickel cathode some metal could be formed and appreciable quantities of reduced chlorides would be present. These reduced chlorides reacted with any oxygen present in the atmosphere above the bath and would also diffuse quickly to the anode (graphite) where they would react with chlorine and be evolved as TiCl4. The net electrolytic efficiency of such a cell is essentially nil. The TiCl4 evolves from the anode at almost the same rate that it is introduced in the vicinity of the cathode although a small amount of titanium metal can be formed on the walls of the cathodic pipe. It becomes apparent from the operation of such a cell that: metal can be deposited on the cathode, although of small particle size and a nonadherent nature, and when reduced chlorides are present in the electrolyte, TiCl4 can be absorbed, probably by the following reactions: TiCl4 + TiC12 - 2 TiCl3 [21 2 TiCl3 + 2 faradays - 2 TiC12 + C12 [31 DIAPHRAGM CELLS These facts encouraged the development of cells containing diaphragms to prevent migration of reduced chlorides from the cathode area to the anode. Small-scale cells for process development are described by Alpert, Schultz, and Sullivan.20 A larger brick-lined cell incorporating internal heating by passing ac through the bath is shown in

Jan 1, 1960

By J. B. Clemmer, P. E. Churchward, C. Rampacek

A cyclic method for processing manganese ores using sodium sulphate as the basic reagent is described. Sodium sulphate is electrolyzed in a diaphragm cell to give an anolyte-containing agentisdescribed.Sodiumsulphuric acid and a catholyte-containing iselectrolyzedincaustic soda, a part of which is carbonated in a cyclic manner to form soda ash. The reduced ore is leached with the anolyte to dissolve the manganese and the impurities are precipitated by addition of catholyte. Manganese in the pregnant todissolvethemanganeseandtheimpuritiessolution is precipitated as synthetic rhodochrosite with a carbonated catholyte, and sodium sulphate is regenerated. Calcining the manganese carbonate gives a high grade product and the carbon dioxide is returned to the carbonation step. The results of laboratory tests using cells equipped with synthetic-fiber diaphragms and permselective membranes, which permit transfer of anions or cations during electrolysis, are described. A METHOD which has been considered for pro-cessing manganese ores under emergency conditions to recover a product suitable for smelting to ferromanganese involves reductive roasting of the ore for leaching with dilute sulphuric acid followed by precipitation of the manganese from the purified pregnant solution with sodium carbonate. Although the process is operable and involves no novel or untried steps, it is noncyclic in regard to reagents. Research seemed warranted to determine if a cyclic process could be developed by electrolyzing the sodium sulphate formed during precipitation of the manganese with soda ash to regenerate sulphuric acid and sodium hydroxide. Reduced ore would be leached with acid anolyte to dissolve the manganese. The iron, alumina, and other dissolved impurities would be precipitated with the caustic catholyte, and the manganese in the purified pregnant solution would be precipitated as artificial rhodochrosite with carbonated catholyte to regenerate simultaneously sodium sulphate for electrolysis. Waste boiler gas and CO, from calcining the manganese precipitate would be recycled for carbonation of the caustic catholyte. There is a surprising lack of data in the technical literature on diaphragm electrolysis of sodium sulphate. One of the more comprehensive papers, by Atwell and Fuwa, describes the problem involved in electrolyzing byproduct sodium sulphate from the viscose process with particular regard to the design and operation of asbestos diaphragm cells. Frisk' also investigated electrolysis of sodium sulphate from viscose-spinning baths to recover caustic soda and sulphuric acid. The objective in these investigations was to produce, by electrolysis and evaporation, a concentrated caustic-soda solution and a sulphuric-acid solution low in sodium sulphate. Because of these requirements, the process was not too attractive despite a favorable yield of caustic and acid with a reasonable power consumption. Because strong acid and base are not required for processing manganese ores and nonelectrolyzed sodium sulphate is not objectionable in either reagent, the present problem was somewhat simpler than that of these investigators. The purpose of this report is to summarize briefly the results of laboratory electrolysis of commercial sodium sulphate in diaphragm cells of different types and the application of the acid and caustic for processing manganese ores in a cyclic manner. Electrolysis in Permeable Diaphragm Cells The principal problem in electrolyzing sodium sulphate in a permeable diaphragm cell is to prevent mixing of the acid and base formed in the anode and cathode compartments. It is not enough to separate the anolyte and catholyte by a single diaphragm. A three-compartment cell in which the sodium-sulphate solution is fed to the center compartment and flows through the permeable diaphragms to the anode and cathode compartments is more efficient electrically. Diaphragms should be porous enough to allow flow of solution to outer compartments but tight enough to prevent gross mixing of the anolyte and catholyte. In addition to being resistant to acid and alkali, the diaphragms should offer minimum resistance to the flow of current. It is also important that the electrolyte contain a high concentration of sodium sulphate to furnish an abundance of sodium and sulphate ions and thereby decrease the current carried by hydrogen and hydroxyl ions. A practical limitation of sodium-sulphate concentration is imposed by the decreased solubility of sodium sulphate with decreasing temperature. At 20°C, a concentration of 200 g per liter sodium sulphate can be maintained. Little is gained in conductivity by using a concentration greater than 200 g per liter. The small-scale continuous electrolysis tests were made in a 12x12 in. open-top bakelite cell equipped

Jan 1, 1956

By T. I. Moore, L. A. Painter

THE electrolytic zinc plant of the American Zinc Co. of Illinois was described by Davidson' in 1944. Since then, improvements as well as expansion of the plant facilities have been made. In order to increase the production of high grade zinc which was needed for war purposes, an expansion program designed to double the slab zinc capacity was started in 1942 and completed in March 1943. This expansion was propagated by a contract between the American Zinc Co. of Ill. and the Defense Plant Corp. The contract included the facilities of the Fairmont City, Ill., property of the American Zinc Co., where a suspension-type roaster with contact acid plant, cadmium distillation furnace, Waelz oxide and densifying plant, and horizontal retort furnaces were installed. The expanded Monsanto, Ill., plant and the additional facilities of' the Fairmont plant were designed to integrate the metallurgical treatment of zinc concentrates for the production of special high grade zinc at Monsanto with the production of acid, cadmium, high grade zinc from furnace skimmings and the Waelz treatment of leach residue at Fairmont. In general, the original flowsheet was not changed, except for the addition of the filtering, drying and reclaiming of leach residue, and the treatment of purification cake for the recovery of copper, cadmium sponge, and zinc. Fig. 1 is a flow diagram of present operations. The original plant facilities, desi-gned for 50 tons daily production of slab zinc, had some units which were more than adequate. Therefore, in expanding the facilities to 100 tons per day, it was not necessary to double all operating components. Table I gives the comparison of the changes made in the unit operating components for the original facilities, 1941, the 1943 expansion, and the 1951 facilities. During the past 11 years a number of improvenients have been made resulting in: 1—an increase in slab production, 2—higher recoveries on the calcine treated, 3—better quality of slab zinc produced, 4—higher current efficiencies, and 5—less man hours Table I. Changes in Operating Facilities Operating Unit 1941 1943 1951 Calcine unloading (pneumatic), 10 tons per hr 12 calcine unloading track hpr. and elev., 60 tons per hr 1 Calcine storage, tons 1,000 2,000 2,000 Leach tanks, 35 vol. tons. No. 3 5 6 slurry mixing 6x6 ft stainless tank, No. 1 Ball mill. 4.5 rt x 16 in. conical. No. 1 CLassifier duplex, No. 1 1 Thickeners. 50 it diam. No. 2 9 2 Filter thickeners, sq ft '-- Moore filters, sq ft 5.760 11,520 Drum filters, 10 ft diam x 16 ft, No. 3 3 Rotary arlers, No. 1 2 1st stage Cu-As purificatlon tank. 90 vol. tons, No. 3 Solution heaters, No. 3 Filter press, 30x30 bronze, No. 4 Zinc dust purification tanks, 45 vol tons. No. 3 5 4 Filter press, 36x36 bronze, No. 3 5 3 Cadmium recovery plant: Process tank. No. 5 2 Cake roaster, 20 ft diam x 4 hearth. No. 1 Filter press, 24x24, No. 4 1 Sponge wash box, 4x6 ft, No. 1 Evaporative cooling unit (vacuum), No. 1 Purified storage tank, vol. tons 400 400 400 Cell acid storage, vol. tons 400 400 400 Electrolytic cells, No. 180 372 372 Cell room ventilation, cu ft per min 35,000 125,000 125,000 Cell cooling water. gal per min 1,500 2,300 2,300 Deep well 16 in. x 95 ft, 1500 gal per min, No. 2 3 3 Melting and casting furnace, 130 ton. No. I Furnace fume scrubber unit, No. 1 Dross drums, No. 2 Dross roaster, 8 ft diam x 8 hearth, No. 1 Electrolysis power conversion, kw 6,250 23,750 23,750 Power transformers, 13,800/440, kva 1,000 1,500 2,000 Steam boilers fire tube, 15 psi, lb per hr 12,000 18,000 18,000 Steam boilers water tube. 125 psi, Ib per hr 30,000 Air compressor, 2 stage. 300 cu ft per min. 100 psi, No. 1 2 Air compressor, 1 stage, 300 cu ft per min, 20 psi, No. 1 Vacuum pumps, 18x7, 720 cu ft per day, No. - - . Vacuum pumps, 24x11, 1.633 cu ft per day, No. 3 3 Building area, sq ft 60,854 113,568 115,000 per ton of metal produced. In the summer of 1944, the "reverse" leaching process was placed in operation and since it has been described,' no further description will be given. Other facilities and changes which have contributed to the process improvements were the scrubbing of fume from the melting and

Jan 1, 1953

By Herbert H. Kellogg

The chemistry of sulfide roasting is analyzed to show those aspects of performance which Thecan be predicted from considerations of thermodynamic equilibrium. It is concluded that equilibrium calculations can serve as a yardstick for prediction of roaster-gas composition and sulfate formation in the calcine for fluid-bed roasting practice. A method of calculation which combines the equilibrium and stoichiometric factors is outlined, and illustrated by an example from the roasting of Cu-Fe sulfides. ON first examination the roasting of sulfides would not seem to be a process to which equilibrium calculations could be applied to yield results of practical value. The burning of sulfides is an ex-tremely spontaneous reaction, excess air is always used to obtain rapid reaction, and in most traditional roaster designs (hearth roasting) the temperature and gas composition vary widely from point to point in the roaster. These are all conditions which promote a non-equilibrium state in the roasting process. However, the introduction of the fluid-bed roaster1 has brought to roasting practice new conditions of operation, so that equilibrium calculations can be used to predict certain limited aspects of practical operation. The fluid bed is characterized by uniformity of temperature, gas composition, and calcine composition from point to point throughout the bed. These relatively uniform properties of the bed make the meaningful calculation of the equilibrium state of certain reactions in roasting possible. It is the purpose of this paper to analyze roasting from an equilibrium viewpoint, to show where the method may be expected to yield valuable information, where it fails, and to outline methods of calculation. Main Roasting Reaction The reaction MS (s) + 3/2 0, = MO (s) + SO, [I] might well be called the main roasting reaction. It adequately accounts for the well known facts that metal sulfide and air are the main reactants, and metal oxide and SO, the main products. Deviations from this simple stoichiometry will be discussed under side reactions. For all metal sulfides, Reaction 1 is strongly exothermic and the equilibrium position is far to the right. Since the reaction is exothermic, the equilibrium shifts in the right-to-left direction as the temperature is raised. However, at all practical roaster temperatures (between 500" and 1200°C), the amount of this shift is small, and the equilibrium position remains far to the right. The main roasting reaction is essentially irreversible, and the application of equilibrium considerations to this reaction will not be! a fruitful field of investigation. A knowledge of the rate of this reaction. although not the proper subject of this paper, is of great importance to the roasting process. Analysis of the factors which influence this rate shows that: 1) The rate will increase rapidly with increased temperature. 2) The rate will be proportional to the partial pressure of oxygen at the surface of the reacting particle. Because of diffusion effects, the partial pressure of oxygen at the particle surface may be considerably less than in the bulk of the roaster gas. For this reason, intimate contact between gas and solid and high relative velocity between gas and solid, such as can be obtained in a fluid bed or flash roaster, will markedly increase the rate of reaction. 3) The rate will be proportional to the surface area of metal sulfide. Therefore, smaller particle size will permit a more rapid rate per unit of weight. To achieve practical rates of roasting the partial pressure of oxygen in the roaster gases must be maintained at a finite level at all times. Even where the gas-solid contact is very good, as in the fluid-bed roaster, the oxygen content of the gas must not be allowed to drop below some limiting value (perhaps 1 pct), or the rate of the main roasting reaction will become too small for practical operation. Side Reactions in the Gas Phase The gas phase during roasting of metallic sulfides contains the elements oxygen, sulfur, nitrogen, by-

Jan 1, 1957