Search Documents

By F. C. Frischknecht

Most early development and application of electromagnetic prospecting methods took place in Scandinavia, where geological conditions favor their use. In other parts of the world these methods have aroused cycles of interest, but in Scandinavia they have been used continuously and successfully since the 1920's. Electromagnetic methods may be classified into two general groups. One group includes methods in which the source of the electromagnetic field remains stationary while the receivers are moved about to explore the area. The other includes procedures in which the energizing and receiving systems are moved together. Other classifications could be based on the size of the energizing source, the particular components of the electromagnetic field which are measured, or the mode of transporting the equipment. The difference between fixed-source and moving-source methods, however, is of such great fundamental importance that it will be emphasized in this discussion. FIXED-SOURCE METHODS Essentially, a fixed-source method consists of the measurement of electromagnetic fields about the source. The mutual coupling between the source and the earth is constant, but the mutual coupling between the receiver and the earth (unless the earth is homogeneous) and also between the source and the receiver changes at each station. The results are usually normalized by relating the field data to the calculated free space or primary field. Turam and Radio Reference Signal Methods: The turam or two-frame* (see Fig. 1A) is probably * Turam means two-coil. the most common fixed-source method. The energizing source is an insulated cable grounded at both ends or formed into a large rectangular loop. Measurements are taken along a traverse at 5 to 50-meter intervals using two small receiving coils, the lagging coil being placed at the position previously occupied by the leading coil. The complex ratio (i.e., inphase and out-of-phase ratios) of the voltages induced in the two coils is measured. Operating frequency range is about 100 to 800 cps. In a typical turam survey a straight, grounded cable several kilometers long is laid out parallel to the probable strike of the ore deposits or conducting strata being sought. An area extending 1 or 2 km on each side of the cable, and within 1 or 2 km of the ends of the cable, is surveyed. Measurements are made at stations 5 to 25 m apart along traverses perpendicular to the cable. Measurements may be made along lines parallel to the cable to serve as base lines for the traverses or for other special purposes. Commonly the receiving coils are oriented with their planes horizontal so that only the vertical component of the field is measured. If additional information is required, one of the hori- zontal components may also be measured by orienting the coils with their planes vertical. In a modified turam technique developed recently for both ground and airborne measurements (Fig. 1B) the amplitude of the complex voltage induced in a single receiving coil is measured and its phase compared with that of a reference signal transmitted from the energizing system by a radio frequency carrier. Thus the un-normalized field is obtained directly, whereas with the turam method it is obtained by calculation from the ratios. The turam method and its modifications have a greater working depth than the other electromagnetic procedures used in ore prospecting. Under favorable conditions conductors have been located at depths of 200 to 300 m. A modified turam method with one of the electrodes grounded in the upper end of a plunging orebody was used to follow the extension of this body to a depth of 200 m beneath a layer of conducting schists. Straight grounded cables are usually preferred to insulated loops because they are easier to lay out and because they often make the method more sensitive. The greater sensitivity of a grounded cable is a result of ground return currents which may flow in the orebodies in addition to the eddy currents caused by induction from the current in the cable. Anomalies in the vertical field due to eddy currents are characterized by a correspondence between high values for the inphase component and positive out-of-phase components and/or low values for the inphase component and negative out-of-phase components. Also the inphase component may approach zero, but it does not become negative. In very long continuous conductors that are parallel to a grounded cable the effect of ground return currents may far exceed the effect of eddy currents. These ground return currents cause a lack of correspondence between the inphase and out-of-phase components and may cause negative inphase or anti-phase components. It becomes difficult to carry out the measurements and often difficult to interpret the results. Such results immediately suggest the presence of graphitic strata, however, since ore deposits are rarely extensive enough to accumulate sufficient ground return current to cause these results. A cable laid out perpendicular to the strike or an insulated loop is sometimes used in areas where graphitic schists and slates are present. Anomalies are then completely or almost entirely due to eddy currents and are easier to interpret. The measured voltage ratios are normalized by either subtracting or dividing by normal field ratios calculated from free space considerations. The normalized ratios are then plotted as individual profiles. When significant anomalies occur in the ratio measurements, the actual normalized fields are calculated by beginning with a measured or an assumed value for the field at a point near the cable and successively multiplying this value by the normalized ratios. There is a similarity between this process and a numerical integration of the ratio curve. Conversely, in many respects the ratio curve is similar to the first derivative of the field curve.

Jan 1, 1960

By W. E. Bonini, E. A. Hickok

IN the course of an investigation directed toward expanding ground-water facilities in Essex and Morris counties, New Jersey, the Board of Water Commissioners of the city of East Orange authorized a seismic-refraction survey' for the purpose of de-lineating bedrock topography below unconsolidated overburden. Results of the survey were highly satisfactory and led to the preparation of a comparatively detailed bedrock contour map. Knowledge of the bedrock depth and configuration was an important aid in selection of sites for test drilling. The portion of the East Orange Water Reserve under consideration is in the flood plain of the Pas-saic River about 10 miles west of Newark, N. J. The flood plain is about 175 ft above mean sea level and is bordered by low hills rising to elevations of approximately 250 ft. The bedrock underlying the Water Reserve consists of sandstone and shale of the Triassic Brunswick formation and is covered everywhere by deposits of unconsolidated glacial outwash sand and gravel, lacustrine clay, and recent river silt as much as 150 ft thick. Yield of wells in the sandstone and shale averages 100 to 200 gpm. Since production wells constructed in the sand and gravel aquifer in the buried river valley shown on the contour map (Fig. 1) yield 300 to 1400 gpm, it was proposed to locate additional production wells in this buried valley, where the yields per well would be maximum. In 1939 and 1946 the East Orange Water Dept. had electrical-resistivity surveys made to determine depths to bedrock. From the resistivity data the exploration company prepared a bedrock contour map. A well field expansion program begun in 1955 utilized this information to locate sites for test wells along a predicted northward extension of the buried valley in which existing production wells are located. After several test wells (wells 201-205) had been drilled, it became apparent that the resistivity information was unreliable." For example, test well 201 recorded bedrock at a depth of 72 ft, whereas the resistivity depth determination was 130 ft. As a consequence, the test drilling program was temporarily suspended and a seismic survey was under- taken to determine the topography and extent of the buried valley known from well records to underlie the existing well field. In the first phase of this study, several seismic shot point locations were placed at sites where well logs had been obtained previously. This procedure is necessary in a new area to determine whether the seismic method is applicable and what degree of accuracy is to be expected. At the East Orange Water Reserve, depths obtained from the shot points near test wells 202, 203, and 204 were within 8 to 11 pct of the depths logged (Table I). With this assurance that accurate results could be obtained, additional seismic spreads were located on the Water Reserve. Using a portable refraction seismograph, in the fall of 1955 a crew of four men shot a total of 29 reversed seismic spreads in a period equivalent to six field days. Charges as heavy as 3 1b of 40 pct dynamite were necessary at a few places to overcome ground vibrations caused by traffic on nearby highways. At most other sites, a 1-1b charge was sufficient. Travel-time plots were made for all spreads, and depths and true velocities were calculated according to formulas for multiple sloping layers by Ewing, Woollard, and Vine.' The plot of spread 7 (Fig. 2) is typical of the short spreads in which bedrock was shallow—about 50 ft in this case. Where there were not enough arrivals through the bedrock to define the high velocity bedrock line, the spreads were lengthened. This was done by placing shots on line several hundred feet away from each end of the line of geophones. It was then possible to construct complete reverse plots for both short and extended shot points (see spread 27, Fig. 3). Four individual depths were calculated from each extended spread. Three and in some cases four seismic layers were observed. The surficial layer had a velocity range of 900 to 1200 fps, the lowest velocity recorded. This seismic layer is above the water table and is interpreted as recent river silt. The bedrock had the highest velocities, which ranged from 10,600 to 16,400 fps. Intermediate velocities ranged from 4500 to 6800 fps. In every case the intermediate layer was within

Jan 1, 1959

By Ramachandra Rao

THE occurrence of copper ores at Garimenapenta, 14 59 min 30 sec N Lat., 79 33 min 10 sec E Long., in Nellore district, Madras State, India, has been examined and investigated on numerous occasions during the past two centuries.' No tangible orebody was ever located as a result of all the ex- tensive trenching and shafting done in the area by various agencies. However, during 1933 Messrs. Piepmeyer & Co., a German firm engaged by one of the leaseholders of the area, carried out an electrical survey using inductive methods.' On the basis of certain strong indications found in their survey, they recommended that the prospect be proved by drilling or shafting. But for want of financial backing no further work was carried out. When the Madras government more recently proposed investigation, Dr. Krishnan, then Supt. Geologist of the Madras Circle, urged that before further costly ventures were carried out a test geo-

Jan 1, 1954

By D. H. Yardley

GEOCHEMICAL investigation of trace elements in surface materials was begun near Ely, Minn., in 1953 along the basal contact of Duluth gabbro with Giants Range granite (Fig. 1). This article presents data on the distribution of copper and nickel in till and in stream sediments in the area and proposes an explanation for the types of distribution found. The Duluth gabbro, one of the world's largest basic intrusives, intrudes rocks which range in age from Keewatin to middle Keweenawan. Within the test area the gabbro is in contact with granite except for short sections where it is in contact with remnants of iron formation. Sulfide mineralization occurs within the gabbro, near and parallel to the basal contact for a distance of several miles. Schwartz and Davidson' have described the geologic setting of the mineralization. The sulfides, believed to be syngenetic, include chalcopyrite, cubanite, pentlandite, pyrrhotite, and minor amounts of bornite. They occur disseminated in the silicates and as small interstitial masses. The ratio of copper to nickel is about 3.8:1, based on 66 chemical analyses of rock samples from various outcrops (Ref. 1, p. 702, and Ref. 2). Test Procedures: With specified exceptions, all nickel and copper tests were made by the chromo-graph method,:' which measures the intensity of a colored spot formed by a reaction between the metal being determined and special reagent paper. The intensity is then compared to the intensity of spots prepared from samples of known metal content. Details of the test procedure are outlined in another article (Ref. 4, pp. 77,78). All soil samples tested in this investigation to date have been weighed on an analytical balance. However, a volumetric scoop designed to provide about 0.1 g of soil adds to the speed and ease of testing and has been found to give satisfactory results (Ref. 5, p. 531, and Ref. 19). The size of the samples used for the tests was 0.1 g. Whenever such small samples are used there is some question as to whether they are representative of the several grams in the field sample. Many repeat tests of the samples used in this investigation demonstrated that results can be reproduced within the limits of accuracy of the method without formal mixing beyond that inherent in screening the soil fractions. Furthermore, the 0.1 g is probably as representative of the field sample as the field sample is of its area of influence. Hawkes and Lakin (Ref. 6, p. 291), who considered the general problem, compared ground and quartered bulk samples of 500 g with 5-g grab samples. They concluded that "there is no significant loss in accuracy of data by substituting grab samples for bulk samples." The term soil implies somewhat different things to the geologist, engineer, and soil scientist.' For convenience the term as used in this article refers to unconsolidated material (the mantle) overlying bed rock. Sampling Procedure: Samples were taken at 100-ft intervals along north-south traverse lines across the gabbro-granite contact. The soil (till) samples were taken at an average depth of 1 ft, which was below the high-humus surface layer and into clean till. Samples taken at 1-ft intervals down to ledge showed as high a metal content at 1 ft below the air-surface as at greater depths and in two instances were slightly higher. The till at 1-ft depth did not appear to differ from material at greater depths. Total depth to bedrock has been tested at only a few points and where measured varied from 1 to 10 ft. Aerial Distribution Contours and Profiles: Plotting of copper, nickel, and cobalt content in contour form (Fig. 2) shows that anomalous amounts of these metal ions occur in till over and closely adjacent to mineralized areas of the gabbro. Contouring nickel content alone, or the copper content, outlines the same target area. Contours of the copper content provide a more distinct anomaly than nickel because of the higher copper concentration. The traverses are rather widely spread for interpolation; however, drilling has confirmed the target area essentially as shown.

Jan 1, 1959

By Robert Uhley, Tsvi Meidav, L. Scharon

Before National Lead built an industrial plant on its Fredricktown property, some 100 miles south of St. Louis, a 750x500-ft area on the proposed site was investigated by electrical resistivity, seismic refraction, and churn drilling. Data were accumulated to prepare an isopach map of the overburden and to determine soundness of the dolomite bedrock and the depth to bedrock at fixed points. The site was on a gently sloping hillside. Elevations above sea level ranged from 760 ft in the northwest corner to 820 ft along the eastern edge, giving a total relief of 60 ft. There were no major drainage features, but in the northern part of the plant site there was an indicated depression area which later was interpreted as reflecting subsurface conditions in the bedrock. No rock was exposed in the entire plant site area; the surface was characterized by soil and overburden. GEOLOGY Prevailing geology in the area of investigation was relatively simple—Bonneterre dolomite overlain by residuum. The red overburden was that derived from the weathered Bonneterre. Some chert was present, interpreted in the general area as a weathering of both the Bonneterre dolomite and younger sedimentary rocks such as the Potosi dolomite. During the period of actual measurements the residuum varied from moist near surface on the western edge of the proposed site to dry near surface on the eastern edge, and for this reason overburden resistivities ranged from low on the west to high on the east. Seismic velocities were low, since the material was not well packed. The bedrock encountered was dolomite, specifically the Bonneterre of Upper Cambrian age which, according to McQueen,' consists of an upper dark gray member and a lower light gray member. These have been further divided into four zones, in ascending sequence a dark gray, sandy argillaceous dolomite; a dark brown or black, fine-grained dolomite: a light gray, finely crystalline, compact dolomite; and, at the top, a dark brown, finely crystalline, compact dolomite. In the area of investigation the upper two zones were encountered in the drilling tests as constituting the bedrock. The dolomite varies widely in porosity, which is low in the dense, fine-grained layers. In this area, therefore, both electrical resistivities and seismic velocities were high. Fracture zones in the Bonneterre are nearly Geology, and may extend to some depth, causing considerable deep weathering. It was realized that over deep fracturing the apparent resistivities

Jan 1, 1960

By A. Becker, J. A. Slankis

Equipment has been developed to utilize natural 8 Hz electromagnetic fields to measure rock resistivities. Telluric and magnetotelluric surveys have detected resistivity variations associated with geological contacts and metallic sulfide deposits. The fundamenfa1 premises of these methods are illustrated by the results of surveys across a Pleistocene-Precambrian contact in the Ottawa Valley and a near-surface sulfide deposit in Northern Quebec. Such interfaces are characterized not only by variations in apparent resistivity, but also, unexpectedly by the spatial anisotropy of the electric fields and the presence of a strong vertical magnetic field component in their vicinity. Standard geophysical electrical and electromagnetic methods (Heiland, 1940) for the determination of the electrical properties of the ground and the search of good electrical conductors necessitate the use of a transmitter and receiver which are coupled galvanically or inductively through the ground. The electrical properties of the ground are deduced from either the transfer function, or the impulse response, of the transmitter — ground — receiver system. Where deep penetration is desired these methods require powerful transmitters whose weight and size increase the cost and reduce the speed of operation. It is possible however, to resort to another class of electrical prospecting methods which employ ambient, natural electromagnetic fields in place of a transmitter.'-' In the audio and subaudio frequency ranges, these fields are generated by thunderstorm activity. At some distance from the seat of the disturbance, the e.m. fields propagate as plane waves with a horizontal magnetic field component. The incident wave, of course, induces currents in the ground. Where the ground is homogeneous the relation between the horizontal magnetic and horizontal electric fields vectors is particularly simple:' /E/ = \[SpT/H/ (1) where: /E/ = magnitude of horizontal electric field in millivolts/kilometer (RMS) /H/ = magnitude of the orthogonal inducing magnetic field in milligammas (RMS) p = rock resistivity in ohm-meters i = frequency of measurement in c/s In practice, the ground is seldom an homogeneous half space, lateral conductivity variations exist, (in the case of base metal prospecting these are the features actually sought) and the two field vectors are no longer simply related. The ratio of E to H is still useful, however, for the determination of an "apparent" ground resistivity. From a theoretical view point, the general problem of a two dimensional fault or dyke anomaly can be separated into two distinct cases. In the first case, where the e.m. energy propagates in a direction normal to the strike, the horizontal magnetic field remains constant and is oriented along the strike of the formation.3 As shown by d'Erceville and Kunetz," all the information about the anomaly is contained in measurements of the electric field component. In fact, away from the interface, the electric fields are proportional to the square roots of the resistivities:

Jan 1, 1970

By T. Koulomzine

The theory of the Askania mag-netometer, as well as a complete discussion of all factors influencing magnetometer readings, is very ably described by J. Wallace Joyce.1 We will assume that the reader is thoroughly familiar with this theory and we will use whenever possible the same notations for the physical values involved in the theory. On the other hand, we believe that the principal formulas of the magnetometer can be deduced much more easily by the use of differential calculus than by the methods employed by Joyce. Consequently, we are presenting herewith a resumé of the theory of the vertical magnetometer in order to determine the correct formula of the temperature coefficient which we propose to compensate. Short Theory of the Vertical Magnetometers We shall accept the following notations: m = total mass of the magnet system, in grams. g = acceleration of gravity, in dynes. a = projection on the axis of the magnet system of the distance between the axis of support and the center of gravity of the magnet system, in centimeters. h = projection on the perpendicular to the axis of the magnet system of the distance between the axis of support and the center of gravity of the magnet system, in centimeters. M = 2pL = M, magnetic moment of the magnet system. Z = vertical component of the earth's magnetic field. ? = deflection angle of the magnet system. = focal length of objective lens in the optical system S = scale reading. In a vertical magnetometer the axis of the magnet system is kept horizontal within 2". Therefore, referring to Fig 1, we see that the magnetic torque of the magnet system influenced by Z must be counterbalanced by the gravity torque. MZ cos ? = mga cos ? + mgh sin ? or dividing by cos ? MZ = mga + mgh tan ? If we now move to another magnetic station and the temperature conditions change, the values of all the variables will change also: M, a, and h under the influence of temperature. 2, both with time and space. ? and S, as a result of all the above changes. Taking increments in Eq 2 we obtain: (Mo + ?M)(Z + ?Z) = mgao + mg?a + mg(h + ?h) tan (? +??) but tan (? +??), because ? is small, can be replaced by tan ? + tan ??; in fact tan (?+ ??) = sin ?.cos ?? + cos ?.sin ??/ cos ?.cos ?? — sin ?sin ?? but sin ? sin ???0 tan (8 + ??) ? tan ? + tan ??. Fur-thermore, neglecting all terms of the equation containing two differentials becomes: or a differential and a tan ??, Eq 3

Jan 1, 1950

By C. T. Bischoff

This paper describes the results of testing with colorimetric methods, using "dithizone", soil samples taken over various known copper and zinc deposits covered by glacial till. Variation in results is shown for different depths and types of overburden as well as grade and type of deposit. Limiting factors for the practical application of this work are discussed. The method has proved successful for copper and zinc deposits under clay and fine sand with depths up to at least 30 ft but fails in coarse sand and gravel unless depths are very shallow. Swamps require penetration to the underlying subsoil for sample material. DURING the past few years geochemical testing for traces of heavy metals in water, soil, rock, and vegetation has aroused increasing interest. Various techniques for field and laboratory determinations have been described in the literature, as have some of the results of application. However, little information has been published regarding application to glacial terrain. Over 90 pct of the Canadian Shield is overburdened, resulting in high costs for mineral exploration once the outcropping ore deposits have been found. This has been largely responsible for the widespread application of mining geophysics in Canada, permitting concentration of effort on area or zones considered most favorable. However, geophysical interpretation has its limitations, since at least 90 pct of the structures indicated thereby contain no valuable minerals. A more direct approach is therefore highly desirable. If underlying base metal mineralization can be detected by sampling soil or vegetation at moderate cost this should prove of great help in locating new discoveries or extending known ones. A large proportion of Canadian ore deposits contain appreciable copper or zinc, even where these are not the principal economic metals. Consequently the field of application is a broad one. This paper deals with investigations along these lines with particular emphasis on soil sampling. The problems involved from the start were: 1—Which types of glacial soil, if any, would best lend themselves to testing, and conversely which types might be considered relatively hopeless? 2—Through what depths of overburden could significant mineralization be detected? 3—What sampling techniques would prove economically applicable? This included minimum depth of sample and maximum spacing that could be allowed.

Jan 1, 1955

By Edward L. Clark, Garrett A. Muilenburg

THE first record of the discovery of iron ore in Missouri was Marquette's observation in 1673 of brown iron ore, or limonite, in the Mississippi River bluffs just north of the mouth of Apple Creek in southeastern Perry County. There is no record of any attempt to mine or smelt Missouri iron ores until 1815, when the Ashebran furnace was erected at the Stouts Creek shut-in near Arcadia, Iron County. Some limonite was treated in this furnace, the first iron furnace west of Ohio, but most of the ore was hematite from Shepherd Mountain and adjacent deposits. Eight years later, in 1823, the Perry furnace five miles north of Caledonia, Washington County, was constructed to smelt limonite ore. It

Jan 1, 1955

By L. O. Bacon

IN the spring of 1952 Calumet and Hecla Inc. began a geophysical program near Shullsburg, Wis., in the Wisconsin-Illinois lead-zinc district, to assist the geological and drilling exploration programs. Sphalerite, the ore mineral in this area, occurs with a considerable amount of marcasite. In general the higher the percentage of sphalerite in the ore, the higher the percentage of marcasite; however, there may be mineralized zones high in marcasite but low in sphalerite. Orebodies in general are relatively narrow and elongated. Reconnaissance exploration of virgin areas consisted of drilling along lines at 500 to 1000-ft intervals. Whenever a mineralized zone was intersected additional drilling was done to determine whether or not the zone carried zinc percentages of ore grade and, if so, to delineate the body. Calumet and Hecla Inc. was interested particularly in a method that would show the direction and position in which to drill from the original discovery hole. This suggested a method of contacting the orebody, which occurs at depths ranging from 100 to 200 ft, with one electrode. After a number of procedures had been considered it was decided to use equipotential line methods. Instrumentation and Field Procedure: The power source used was a 400-cycle Signal Corps motor-generator having a rated output of 1200 w at 115 v. The detection unit consisted of test probes, a two-stage amplifier, and &apos;head phones for determining the equipotential line by audio null. Field procedure consisted of contacting the sulfide body in the hole by a specially built spring-loaded expanding electrode which would be lowered into the hole, in the closed. position, until it reached the mineralized zone. At that point the mechanism was released so that the arms would make contact with the walls of the hole in the same manner that a well-bore caliper does. This electrode was then connected to the generator, the other terminal of which was connected to the surface electrode. The surface electrode was either a point, a straight line, or a circular line electrode. The point surface electrode was placed at a considerable distance from the hole, that is, 2500 to 5000 ft, depending somewhat upon the depth to the sulfide zone and the distance from the hole containing the subsurface electrode to which exploration was considered. A higher voltage output from the power source would have been desirable, although no difficulty was encountered in determining null points to a distance of 500 ft. Straight line electrodes used were approximately 1000 ft in length at a distance of approximately 1000 ft from the hole containing the subsurface electrode. The circular line electrode used consisted of 4400 ft of bare No. 10 copper wire, which provided a circle of 700-ft radius. All line electrodes were fastened to the ground at 20-ft intervals with copper staples 4 in. long. Equipotential points were determined at 25 to 100-ft intervals. Location of the points was made by plane table and stadia. In open country with a three-man crew, the points were plotted as they were determined. With a two-man crew, pegs were placed at equal potential points and surveyed in after several equipotential lines were determined. Although interpretation of results given in this paper is qualitative, the paper as a whole would not be complete without a discussion of the theoretical distribution of potential due to a circular line electrode. The theoretical distribution would be required if a quantitative interpretation of the measured potential distribution were to be made. The theoretical potential distribution due to a circular line electrode can be obtained by means of Legendre polynomials. Using the method as developed by Weber,&apos; the potential for a circular line electrode in a semi-infinite, homogeneous, isotropic medium can be expressed, using the spherical coordinate system, as: V(r,n) = pi/2pR[S(r/R)nPn(cos?)Pn(cosa)]r<R [1] er V(r,a) =pI/2pr[S(r/R)Pn(cos?) Pn(cosa)]r>R [2] where: 0 is the angle at the origin, taken on the axis of the circular electrode between the axis and the line drawn to the circumference of the circular electrode. a is the angle between the axis and the radius, r.

Jan 1, 1957

By Walter J. Johnson

The coals in northern Wyoming and Montana are free-burning and non-caking and range from lignite to bituminous C in rank. Strip and underground mining are employed to supply railroad, utility, industrial, and domestic fuel. The market area includes Iowa, Nebraska, Minnesota, North and South Dakotas, Wyoming, Montana, the Pacific Northwest, and western Canada. THE larger producing coal mines in northern Wyoming are located in the Powder River Basin lying between the Black Hills region of South Dakota, eastern Wyoming, and the Big Horn Mountains in north central Wyoming, see Fig. 1. The mines are located particularly in the area along the route of the Chicago, Burlington & Quincy Railroad from Gillette, Wyo., to a point approximately 15 miles northeast of Sheridan, Wyo. Fig. 2 is a graph of coal production in the state of Wyoming from 1918 to 1951. Across the Big Horn Mountains lies the Big Horn Basin, situated between the Big Horn Mountains and the Rocky Mountains proper. Mining in the Big Horn Basin is almost entirely confined to a small area known as the Gebo Field, near the town of Kirby, which is located on the Chicago, Burlington & Quincy Railroad. This paper will describe present operating areas, making only brief reference to the history of mining and marketing primarily because of the large area to be discussed. The coal beds presently mined in the Powder River Basin are all of Tertiary age and are of Fort Union and Wasatch formations of Paleocene and Eocene ages, see Fig. 3. The Fort Union formation, consisting of 2000 to 3200 ft of alternate sandstone, shale, and coal, is divided from oldest to youngest into the Tullock, Lebo Shale, and Tongue River members. Most of the mineable coal is in the Tongue River member, which is 500 to 800 ft thick. The Carney coal bed, varying from 7 to 20 ft in thickness, is considered the base of the Tongue River member. About 85 ft above the Carney is the Monarch bed, ranging from 18 to 42 ft in thickness. At approximately 210 ft above the Monarch is what is locally known in the Sheridan district as Dietz No. 3 bed, which varies from 12 to 30 ft in thickness. One hundred feet above the Dietz No. 3 is Dietz No. 2 bed, which is 7 to 12 ft thick. At about 100 ft above the Dietz No. 2 is Dietz No. 1 bed, 7 to 15 feet in thickness. Two hundred and fifteen feet above Dietz No. 1 is the Smith bed, approximately 5 ft thick. One hundred twenty-five feet above the Smith is the Roland bed, which is estimated to be approximately 13 ft thick. The Roland bed is considered the base of the Wasatch formation, which in the Powder River Basin is 1000 to 3500 ft thick and is composed largely of shale, sandstone, and coal. The foregoing measures are the only ones above the Tongue River member that have been mined in the Sheridan field. To the east of the Sheridan field, particularly in the area of Gillette, the Roland bed is considerably thicker and is considered the thickest and most extensive coal bed in Wyoming, reaching a maximum thickness of 106 ft. From 125 to 225 ft above the Roland lies the Arvada bed, average thickness 9 ft. Three hundred seventy-five to four hundred feet above the Arvada is the Felix bed, which reaches its maximum thickness of 30 ft near Echeta on the Chicago, Burlington & Quincy Railroad. East of the Powder River the bed averages more than 10 ft in thickness, but it thins in a northwesterly direction. The highest mineable coal in the Powder River field is the Healy bed, about 400 ft above the Felix bed and exposed only in the highest parts of the area where much of it has been burned along the outcrop. Where it has not been burned, the thickness at most of the outcrops is 10 to 15 ft.

Jan 1, 1954

By J. J. Jakosky

The strategic importance of the metallic minerals in our industrial economy, and the declining rates of discovery have focused attention on means of exploration for new mineral deposits. A consideration of exploration techniques leads to an attempt to evaluate the effectiveness of geophysics as a tool for mining exploration. One means of evaluation will be to compare the use of geophysics in petroleum exploration with its possible uses in mining. Geophysics in Petroleum Exploration During the past twenty years, the petroleum industry has established an effective exploration technique. Geology is the basic tool in those areas where reliable predictions can be made from surface conditions. In the other areas, where the geological studies are inadequate, they must be supplemented with geophysics or direct exploration, such as drilling. Since geophysical work is far less costly than any form of direct explbration, it is used almost exclusively as the means for obtaining the desired subsurface information. The geological and geophysical techniques are credited with locating sites which yielded one producer for three dry holes during the year 1947.&apos; For the wells located without geology or geophysics, there is a ratio of one producing well to sixteen dry holes. From these figures it is seen that the geological and geophysical techniques are more than four times as successful as the nontechnical exploration. It will be in order to consider further this ratio of one producer to three dry holes. The geophysical methods in use today† do not pretend to locate oil directly; their function is to locate anomalies or structures favorable for the accumulation of oil. For a producing oil well we must have not only structure, but also other favorable conditions, namely: petroliferous source beds, the required porosity and permeability in the reservoir rocks, an impermeable cap rock over the reser- voir, and the necessary water or gravity drive to force the oil into the bore hole. Since the geophysical work can only detect and sometimes delimit the anomaly, these other necessary conditions can be determined only by direct exploration. The success of modern geophysical work in locating and limiting the structure itself is remarkably high, probably over 95 pct accurate. Geophysical work renders an important service in the delineation of the structurally unfavorable areas and their elimination from the drilling phase of the exploration program. When attempting to locate any material of scarce occurrence in the earth, it is of paramount importance to know where not to dig. This elimination of barren areas is the least appreciated but is of great economic importance. For illustration, the difference between one producer to three dry holes, and one producer to sixteen dry holes, represents a saving of thirteen drilled wells, which would require an expenditure many times the cost of the geophysical work that might have revealed the nonfavorable structural conditions. The percentage of geophysically-located wells necessarily will continue to increase in the statistics of future years, as the search for oil is extended

Jan 1, 1950

By W. Allen

FOR the past six years gravity surveys have been used for underground prospecting in the copper mines at Bisbee, Ariz. The primary purpose of the surveys has been to reduce the diamond drilling and crosscutting necessary for exploration. Since many of the orebodies are small, and geologic control is not always apparent, any information that will direct the drilling and crosscutting is highly desirable. Because of extensive development and exploration work in the copper mines at Bisbee, it has been possible to cover more than 630,000 ft of crosscuts on 30 levels with the gravity surveys. In the process the gravity procedures have been refined to a high degree. Density Contrast: For a gravity survey to be successful, a sufficient density contrast must exist between the geologic feature sought and surrounding host rocks. Most mineralized areas will provide this contrast if fairly massive bodies are present. In the Bisbee area the entire sequence of formations, except for alluvium, appears to have specific gravities ranging from 2.65 to 2.70. These values have been determined by means of a large number of cut samples and diamond drill cores. As a further check, vertical gravity differences have been used where nonmineralized sections are known to occur.&apos; The only known major gravity disturbances result from mineralization that has increased the density and the voids that have decreased density. The voids are caused by mining operations and by underground water movement that has developed several areas of caverns. Equipment: While not absolutely essential, a small rugged gravity meter, such as the Worden meter, is highly desirable. A tall tripod, about the height of a transit tripod, permits instrument set-ups in deep water and in locations where fallen timber and muck piles make it impossible to use a short tripod. An additional advantage of a tall tripod is that it places the meter in the center of the crosscut, reducing the error caused by the crosscut void. Size and weight are important, since the only satisfactory means of operating the meter underground is to carry it by hand. A backpack can be used in rare instances but is usually a hindrance because of the close station spacing. The operator&apos;s ability to move through tight clearances will improve survey coverage, as it is then possible to move through raises and caved areas and to pass mine cars and machinery with a minimum of trouble. Station Control: Gravity stations are normally located every 100 ft along the crosscuts, at each intersection, and in the face of all stub crosscuts. In areas of high gravity relief, or where small anomalies might be expected, stations may be located at 25 or 50-ft intervals. When possible, the stations should be offset to avoid effects of raises or other voids. The gravity stations on a level are tied to one or more base stations, which are usually located at the shaft or near the portal of an adit. The base stations may be part of a gravity control net that extends to each level in the mine as well as to the surface. Such a net extending throughout the potential area of the surveys is highly desirable, as it is then possible to compare all gravity stations on a uniform basis. The stations that are part of the base net should be carefully established by multiple readings and, if necessary, by a least squares adjustment of the loops. In some instances where levels do not have a shaft station, or where access may be blocked by caving, it may be necessary to establish secondary bases at the top and bottom of the raises that are between levels. Under fair conditions 70 to 90 gravity stations can be located and run in 6 hr by a two-man crew. The best field procedures depend on conditions. Reduction of Field Data: Most of the time required to produce a final gravity map is consumed in processing the data. Each meter reading must be corrected for a minimum of five factors that affect the gravity value in addition to the density contrast being sought. These factors are 1) instrumental drift, 2) station elevation, 3) topography, 4) latitude, and 5) regional gravity gradient. Mine openings, such as stopes and raises, will affect the value. However, it is seldom practical to make corrections for these voids. Usually a rotation is made on the field note on the station, and any

Jan 1, 1957

By W. A. Longacre

IN the geophysical exploration program of the Cleveland-Cliffs Iron Co. on the Marquette Range of Northern Michigan, the vertical intensity magnetometer has been used to obtain magnetic anomaly maps of large areas. A network of magnetic base stations has been established and the relative vertical intensity at each station measured carefully with respect to a prime base. In the search for the relatively nonmagnetic soft red hematite ore, the magnetic exploration is indirect, involving the study of dikes, faults, contacts, and other structural features. It was found that the magnetometer, adjusted to a scale value of approximately 40 ? per scale division, was satisfactory for this type of exploration, although many magnetic anomalies were encountered that required the use of auxiliary magnets.

Jan 1, 1952

By D. J. Carney, E. Richard Randolph, E. Van Meter, J. J. Oravec, Stanley H. Ward, Gerald J. Anderson, Rolland L. 203-000-000-005 Blake

DURING the last 30 years the inductive electromagnetic method has been used chiefly in the search for massive sulphide mineralization. This application has met with varying degrees of success and in recent years has resulted in discovery of several large orebodies. Little has been written concerning its use in exploration for soft iron ores, but one of the present authors has reported on experiments with massive magnetic deposits.&apos; To augment the exploration tools available to geologists in delineating iron orebodies, Cleveland-Cliffs Iron Co. and McPhar Geophysics Ltd. undertook in 1953 to apply the inductive electromagnetic method to Cleveland-Cliffs properties in the Lake Superior region. As a result of this project, equipment has been developed that enables simultaneous transmission of two audio frequency waves, and the field technique and interpretative procedure involved have furthered exploration in the district significantly. Thus far, inductive electromagnetic application in the Lake Superior region has been only a development tool, that is, it is used to locate obscured contacts and faults as a part of property expansion and development. However, its application to primary reconnaissance of unexplored areas may be feasible in the future. The method has assisted in placing drillholes efficiently, and the elimination of excess drilling foot-ages and/or actual elimination of unnecessary holes has amply justified the expense of the geophysical survey. Cost of the field work involved is comparable on a per station basis to the cost of a magnetometer or superdip survey. Since observations require no reduction, i.e., are directly interpretable, overall expenditure is low, and the scope and detail of the survey can be adjusted in the field as geological- geophysical correlation becomes evident. To a great extent, this eliminates the second-guessing so commonly arising after office calculations are completed on data obtained with other types of geophysical surveys. This unique feature of field interpretation and its associated intimate feel of the project area, is, perhaps, one of the most valuable aspects of the inductive electromagnetic method as applied to iron ore exploration. Basis of Method Fundamentally, the method involves transmission of an alternating electromagnetic wave, of a chosen audio frequency, which permeates the ground materials in the vicinity of a transmitting, or primary, coil, see Fig. 1. This wave, or field, induces an electric current in any conductor on which it is incident. The flow of an alternating current in a conductor sets up its own, or secondary, radiating electromagnetic field. These two fields form a resultant whose configuration depends on the following characteristics of the subsurface conductors: 1) size, 2) shape, 3) electrical conductivity, 4) magnetic permeability, and 5) frequency of the transmitted wave. To a lesser extent the resultant is also dependent on material adjacent to the conductor, topography, and surface conductivity. For illustrative purposes, the primary, secondary, and resultant fields may be represented by vectors. In operation, the direction of the resultant vector is measured by a small receiving coil tuned to the frequency of the transmitted wave. Generally speaking, the method can be compared to the transmission and reception of the familiar radio broadcast, with special variations permitting measurement of the effect on reception of intervening materials. Field Technique Mechanics of field operation are simple. The mast is set up in a vertical position and is then guyed in place. The transmitting loop then is raised by means of a sheave at the top of the mast and the coil connected to the motor-generator. A special plane table is clamped into position on the mast and the loop is plumbed. The plane table is oriented according to a grid system established over the project area. By means of this plane table it is possible

Jan 1, 1956

By G. W. Brownell, H. T. F. Lundberg, R. W. Pringle, K. I. Roulston

The rapid improvement of the airborne scintillometer and the perfection of its efficiency for counting low energy gamma radiation has made it possible to work out a technique to map in great detail the radiation pattern at the earth&apos;s surface. On such maps low radiation over certain areas appears to indicate the existence of oil accumulations, forming a pattern similar to that obtained by the geo-chemists. RADIOACTIVE analyses of samples from the surface of oil fields were carried out more than 10 years ago in Alberta by the alpha particle ioniza-tion chamber technique,&apos; but large enough tracts could not be covered in these investigations to make possible any evaluation of the method as a means of oil exploration. Considerable interest has recently been revived, however, as a result of certain striking advances which have been made in the instrumentation available -for the measurement of radioactivity. It is the object of this paper to indicate the nature of these improvements in radiation technology and then to describe the attempts that have been made to interpret the radioactive patterns obtained in the course of airborne recordings with the new instruments. Since the survey can be carried out from the air and records can be accumulated over vast areas in a short time, the result may easily lend itself to statistical treatment. Areas have been surveyed in Alberta, British Columbia, Saskatchewan, Quebec, Texas, New Mexico, Nebraska, Colorado, Utah, and Montana. Producing fields in Alberta and West Texas have been flown over several times in different directions, Fig. 1. The operations were then extended into unknown territory and drill holes were put down on the anomalies which looked promising. The results from these drillings were encouraging and have given hopes for the development of an entirely new method of oil exploration. Any large scale method for the survey of radioactive anomalies must be based on the measurement of gamma rays, as beta and alpha rays have much too short a range to be of any significance. Thus the essential improvement which has made the present stage of this work attainable is the development of new highly sensitive detectors for gamma radiation. In the past the only detectors of any consequence that were available were the ionization chamber and the geiger counter, but both of these suffer from the defect that only a small proportion of the gamma rays passing through the counter are detected, possibly 0.1 to 0.2 pct. The recent development of the scintillation counter2,3 has completely transformed the situation and has had a considerable impact on many branches of nuclear technology. The detection of alpha particles in zinc sulphide screens by visual observation of the individual scintillations which these particles produce dates back to the early spinthariscope of Rutherford and Crookes, but the combined use of an appropriate scintillating phosphor and photomultiplier tube had to await the technical development of the latter many years later. With this development came the modern era of the scintillation counter and a knowledge of phosphors which have a large light output under the bombarding action of gamma radiation. Some of these phosphors are relatively dense and are capable of stopping a large proportion of the incident gamma radiation. As the sensitive region is the whole volume of the crystal, a very high detection efficiency, 50 pct or more, can be obtained for medium energy gamma rays. Scintillation counters for geological purposes were first developed in 19494-6 in an attempt to utilize this remarkable improvement in efficiency, which has the attractive consequence that only a small portion of the normal background of the counter is due to cosmic radiation. In 1949 tests were made in northern Saskatchewan by Lundberg Explorations Ltd. with portable scintillation counters which gave excellent results in the search for uranium and served to indicate unknown uranium deposits in areas previously closely surveyed with geiger counters. Portable scintillometers (registered in Canada) are now commercially available and in regular use,&apos; and the adaptation of the instrument to radioactivity oil well logging has also been very successful.8 Initial attempts to measure radioactivity from aircraft with scintillation counters were made during this period in the same area and yielded most encouraging results. It would be appropriate to consider some specific requirements for airborne investigations. The essential problem to be met in the detection of any radioactive source is the necessity of obtaining a signal greater than the statistical fluctuations of the background counting rate for the instrument. It is possible to show that Nt>2k2 is the condition for detectability of a signal where N = average background counting rate for the detection. t = time constant of the counting rate meter, used to determine the average number of counts arriving in a certain predetermined time interval. N&apos; = average source counting rate at the detector. k = N/N&apos;, and N>>N&apos;. Sample values are given in Table I. Assume that the aircraft carrying the equipment is travelling at 120 mph, in which case it will cover 176 ft in 1 sec. Assume also, as a first approximation, that a point source target is in range when the air-

Jan 1, 1954

By J. B. Macelwane

Historically whenever application of scientific results to a new problem required the special experimental background, the economic outlook and the practical knowledge characteristic of the engineer, a curriculum in that type of engineering based on the professional requirement grew up in the engineering colleges. This is precisely what is happening now in geophysical engineering. THE Mineral Industry Education Division of AIME has long been interested in geophysical education. Organized in 1938, a Committee on Geophysical Education presented a number of reports in succeeding years. The AIME is an engineering society; hence it might be expected that the interest of the Mineral Industry Education Division would have centered about the relation of courses in geophysics to engineering education. However, this was not the case. The burden of the discussion held under the auspices of the Committee on Geophysical Education bore on geophysics in general and particularly on its relation to geology. In the decade that has passed since those meetings much water has flowed under the bridge. Not only have the geophysical sciences developed at an extraordinarily rapid rate but the practical importance and the range of their applications have spread in ever widening circles and have even assumed a very prominent place in research programs of the military, the Army, the Navy and, particularly, the Geophysical Research Directorate of the Air Force at Cambridge, Mass. So enormously have the geophysical sciences as such grown in scope and in degree of specialization that no one man in a lifetime of study can hope to master the theoretical and experimental complexities or even to follow intelligently in the published literature all the varied accomplishments of basic research in these fields. As in the other sciences, most of the results of geophysical research have potential economic value and are being applied to a wider and wider range of human needs. Here we see a parallel with the older sciences and their relation to engineering. Whenever the applications of scientific results required the special experimental background, the economic outlook, and the practical knowledge characteristic of the engineer, a curriculum in that type of engineering grew up in the colleges and universities. In the words of the "Report of the Committee on Adequacy and Standards of Engineering Education" in the January 1952 number of the Journal of Engineering Education: "Engineering education in America was not developed after a preconceived plan. It evolved in parallel with the needs of a growing country, a country engaged in the development of a vast industrialization. From the first it filled a practical need, and its design emanated largely from an evaluation of the professional requirement." The advent of the railroad created a need for scientifically trained engineers and the response was the curriculum in civil engineering. The development of steam power created the demand for a curriculum in mechanical engineering. Neither of these types of engineers was trained to cope with the requirements of electrical power, and so there came to be a curriculum in electrical engineering. The advent of radio communication and of electronics during the first World War and in the years that followed resulted in the establishment of electronics engineering, sometimes within the curriculum in electrical engineering and sometimes independent of it. The complexities of industrial management have created an ever increasing demand for industrial engineers and the consequent building up of a curriculum in industrial engineering. The wide industrial application of chemical processes required a type of engineer whose background was training in chemistry but who was able to design processes and plants on an industrial scale; hence we have the curriculum in chemical engineering. The advent of the airplane created an entirely new set of problems which were solved by the training of aeronautical engineers. Many of these have called for more and more science and mathematics. Such was the history of the older engineer-

Jan 1, 1953

By J. B. Macelwane

Historically whenever application of scientific results to a new problem required the special experimental background, the economic outlook and the practical knowledge characteristic of the engineer, a curriculum in that type of engineering based on the professional requirement grew up in the engineering colleges. This is precisely what is happening now in geophysical engineering. THE Mineral Industry Education Division of AIME has long been interested in geophysical education. Organized in 1938, a Committee on Geophysical Education presented a number of reports in succeeding years. The AIME is an engineering society; hence it might be expected that the interest of the Mineral Industry Education Division would have centered about the relation of courses in geophysics to engineering education. However, this was not the case. The burden of the discussion held under the auspices of the Committee on Geophysical Education bore on geophysics in general and particularly on its relation to geology. In the decade that has passed since those meetings much water has flowed under the bridge. Not only have the geophysical sciences developed at an extraordinarily rapid rate but the practical importance and the range of their applications have spread in ever widening circles and have even assumed a very prominent place in research programs of the military, the Army, the Navy and, particularly, the Geophysical Research Directorate of the Air Force at Cambridge, Mass. So enormously have the geophysical sciences as such grown in scope and in degree of specialization that no one man in a lifetime of study can hope to master the theoretical and experimental complexities or even to follow intelligently in the published literature all the varied accomplishments of basic research in these fields. As in the other sciences, most of the results of geophysical research have potential economic value and are being applied to a wider and wider range of human needs. Here we see a parallel with the older sciences and their relation to engineering. Whenever the applications of scientific results required the special experimental background, the economic outlook, and the practical knowledge characteristic of the engineer, a curriculum in that type of engineering grew up in the colleges and universities. In the words of the "Report of the Committee on Adequacy and Standards of Engineering Education" in the January 1952 number of the Journal of Engineering Education: "Engineering education in America was not developed after a preconceived plan. It evolved in parallel with the needs of a growing country, a country engaged in the development of a vast industrialization. From the first it filled a practical need, and its design emanated largely from an evaluation of the professional requirement." The advent of the railroad created a need for scientifically trained engineers and the response was the curriculum in civil engineering. The development of steam power created the demand for a curriculum in mechanical engineering. Neither of these types of engineers was trained to cope with the requirements of electrical power, and so there came to be a curriculum in electrical engineering. The advent of radio communication and of electronics during the first World War and in the years that followed resulted in the establishment of electronics engineering, sometimes within the curriculum in electrical engineering and sometimes independent of it. The complexities of industrial management have created an ever increasing demand for industrial engineers and the consequent building up of a curriculum in industrial engineering. The wide industrial application of chemical processes required a type of engineer whose background was training in chemistry but who was able to design processes and plants on an industrial scale; hence we have the curriculum in chemical engineering. The advent of the airplane created an entirely new set of problems which were solved by the training of aeronautical engineers. Many of these have called for more and more science and mathematics. Such was the history of the older engineer-

Jan 1, 1953

By Milton Glicken

THE airborne geophysicist is a busy man these days. In his plane he may have the airborne magnetometer, the airborne scintillation counter, and the airborne electromagnetic surveying system. Each of these is an independent tool, but all require additional auxiliary equipment for locating the aircraft in space: recording altimeters and Shoran or aerial cameras. Now there is still another piece of equipment, the airborne magnetic gradiometer, an accessory to the magnetometer. To understand its uses, consider the function of the magnetometer itself. Aside from detecting magnetic ore, the airborne magnetometer finds greatest use in spotting intrusions of igneous material. Where there is enough contrast in magnetic susceptibility of igneous rock and adjacent formations, it outlines the intrusion. Certain minerals also influence the magnetometer directly, but with the exception of magnetite and possibly one or two others, their effect is weak and can be detected only when there is sufficient ore and the magnetometer flight passes very close to it. An igneous intrusion of infinite depth with vertical sides is represented on a magnetometer record by an anomaly, as in Fig. 1. Amplitude of the high depends on susceptibility contrast of the igneous rock. Generally speaking, the edge of the intrusion lies below the point of inflection of the curve, and this point, where the curvature changes from positive to negative on the magnetometer profile, would be near A in Fig. 1, with a counterpart, of course, on the other side. Location of the contact is one of the principal objects of the survey, but finding the precise point is not always easy, as inspection of the curve near A will show. Mineralization is often found at the contact zones, as at B. Magnetic effects, if detected, may be small, as in B&apos;, and when superimposed on the anomaly due to the instrusion they are very difficult to discern and analyze. Furthermore, if these small fluctuations are to be perceived by the magnetometer the vertical scale should be large. This increases the slopes of the anomaly and makes detection of small deviations and inflection points even more difficult. The airborne magnetic gradiometer was designed to help overcome these difficulties. What it presents is the first derivative of the magnetometer record with respect to time, that is to say, the slope at any point. Fig. 2 represents an actual magnetometer record (solid line) with the corresponding gradiometer record (dashed line) superimposed. Both records read from right to left. Vertical lines on the original magnetometer record are automatic steps designed to keep the pen from going off scale. The slope of any curve is greatest at the point of inflection or point where the curvature changes sign, and this point is a maximum (or minimum) on the gradi- ometer. The chief advantage of the gradiometer is that maxima or minima are much easier to see and to locate precisely; hence an accurate location for the point of inflection can easily be found. Note that points C and D are more sharply defined than C and D&apos;. Similarly the small fluctuations of the original record, so important to the interpreter, are far more clearly shown at E, F, and G, than on the original record at E&apos;, F&apos;, and G&apos;. Though not necessarily highs and lows on the gradiometer, they do show up clearly what would take a painstaking analysis to detect on the original magnetometer record. Will the gradiometer have a particular configuration which indicates an orebody? Not necessarily. The total intensity curve, or original magnetometer record, can display an orebody in various ways, depending on dimensions, orientation, latitude, and composition, as well as on direction, flight height, and instrumental sensitivity of the traverse. Where the total intensity can take on so many different shapes the gradiometer must vary too. It is generally recognized that interpretation of total intensity magnetometer records requires an expert analysis; the gradiometer can be of considerable assistance to the expert but it does not replace him. Mechanism of the gradiometer is simple. A Leeds & Northrup recorder in the aircraft records the magnetic gradient simultaneously with the total intensity, which is on another recorder. Fiducial marks are put on both records simultaneously and the speed of the paper through the recorders is kept the same on both. This makes it possible to place one record over the other for direct comparison. In the laboratory the flights are positioned on a map. Maximum and minimum points on the gradiometer, which can then be posted on the map at their proper locations, may be expected to fall along a trend crossing the direction of flight. Trends should indicate the edge of an intrusion, or some other important features, and when superimposed on the total intensity contour map help greatly to locate the points of inflection, or line of zero curvature.

Jan 1, 1956

By D. F. Malott

The Michigan Dept. of State Highways makes extensive use of geophysics for subsurface surveying which would be applicable for uses in other fields. Examples of resistivity surveys are given which include a proposed large-volume excavation with suggestions for land use after excavation, subsurface evaluation for engineering design, and a subsurface survey for land appraisal. An example of a combined refraction seismic and resistivity survey is shown where the resistivity is used for outlining the unconsolidated soils, while the seismic method is used to outline bedrock and to evaluate it for rippability. A refraction seismic survey at the bottom of bridge caissons for evaluation of bedrock uniformity and a rehtive aid in assessing rock strength is reported. These past several years have been a period of unprecendented construction and commercial expansion. Vast private manufacturing complexes and government road, power, and office projects are being built or are in planning stages. Nearly everywhere, municipalities are expanding outward and upward. Many towns are developing into cities and many cities are displaying new skylines, and the building boom shows little sign of slowing down.

Jan 1, 1970