Search Documents

By W. E. Newell

The basic principles and assumptions involved in D. L. White's solution5 for ultrasonic wave amplification in piezoelectric semiconductors are summarized. If the gain per unit length is maximized at each frequency without regard to the drift-field power density, the gain increases linearly with frequency. Therefore it would seem that very high gain is possible for frequencies in the hundreds of megacycles. However, with present materials the resulting drift-field power density is so large that cooling would be a major problem. For this reason it is more realistic to judge the capabilities of an ultrasonic amplifier in terms of the gain that is possible with a specified power density. In this case the gain at high frequencies does not increase but decreases more rapidly than l/f. The calculation of the gain us frequency at a fixed power level involves the repeated solution of a cubic equation and is therefore tedious. For the purpose of comparing different materials, sufficient accuracy can be obtained from an approximate solution which may easily be plotted as three straight lines on logarithmic graph paper. This method is used to compare the Performances of CdS, CdSe, ZnO, and GaAs. At a power density of 10 watts per cu cm, the first three give maximum gains of 60 to 80 db per cm in the vicinity of 60 megacycles. At the same power density, GaAs has a maximum gain of about 7 db per cm near 150 megacycles. Although an increase in mobility usually increases the gain for a specified power density, it is shown that there is an optimum mobility above which the gain decreases. An approximate expression for the optimum mobility is established. It is well-known that the interaction between charged particles and an electromagnetic wave can be used to amplify the electromagnetic wave. In the conventional traveling-wave tube, electrons in a vacuum are caused to move at a velocity slightly greater than the wave velocity, thereby coupling energy into the wave.' In principle, the same effect would be evident in a solid except that repeated collisions prevent the electrons from attaining a velocity greater than that of an electromagnetic wave. However, the drift velocity of electrons can be made to exceed the velocity of an acoustic wave in a solid. In 1956, weinreich2 noted that the deformation potential provided one means of coupling energy from drifting electrons into an acoustic wave, but the effect was too small to be of any practical importance. It was not until 1961 that White and Hutson demonstrated that the piezoelectric effect provided a strong enough coupling to give appreciable amplification of an ultrasonic wave and awakened wide interest in electron-phonon interactions. Qualitatively the effect may be described as follows. An acoustic wave propagating through a piezoelectric material is accompanied by an electric-field wave. If the vibrations are properly oriented with respect to the crystal axes of a piezoelectric semiconductor, the local electric fields are axially directed and cause bunching of the charged carriers. If the drift velocity of these carriers is less than the velocity of sound, they tend to be dragged along by the acoustic wave. This electroacoustic effect results in a net potential appearing across the material and in attenuation of the acoustic wave. On the other hand, if the drift velocity exceeds the velocity of sound, energy is coupled from the carriers to the acoustic wave and amplification results. Related effects which are being investigated include ultrasonic amplification in semimetals6-' and semi-conductor, and current saturation in piezoelectric semiconductors.'4-17 There are various problems which hinder the immediate application of ultrasonic amplification in a practical device. First, there are the traditional problems encountered in the design of acoustic delay lines: attenuation in the electromechanical transducers, reflected waves (which can lead to self-oscillation in an amplifying device), mechanical tolerances necessary to maintain phase coherence, and so forth. Second, there is the problem of selecting the best material from among the various piezoelectric semiconductors as they become available in single-crystal form with a wide choice of characteristics. This paper deals with the second problem and shows that the most realistic way of comparing materials is in terms of the gain which can be obtained without exceeding a

Jan 1, 1964

By P. Schwarzkopf, J. H. Brophy

A modification of the Mendenhall wedge blackbody1 has been used to determine solidus temperatures and to anneal alloys in the tantalum-rhenium binary system. The technique has proven to be simple and accurate with modest power requirements. For temperatures up to 2800° C a piece of 10-mil tantalum sheet was folded double and formed as shown in Fig. 1. The middle of the resulting ribbon filament was a cylindrical-shaped crucible with less than a 1/8-in. opening. After inserting a specimen in the cavity, the filament was clamped between molybdenum electrodes in a high vacuum chamber. A representative filament 2 in. long and % in. deep was heated to 2800°C with a current of 700 amp at 4 v. The specimen temperature was determined by sighting into the cavity with a Leeds and Northrup optical pyrometer. The twisted filament shape was necessary to avoid serious geometric changes during thermal expansion. For temperatures between 2800" and 3000°C a 4-mil tungsten filament was employed. To facilitate fabrication it was warm-folded, and a twisted segment of 10-mil tantalum was used to support one end to absorb thermal expansion. This element assembly required about 700 amp at 10 v to reach 3000°C. Two geometric modifications of the filament were helpful for solidus temperature determinations. A shallow chamber, with depth to opening ratio of 3 to 1, permitted direct observation of the specimen through the optical pyrometer. The fact that the specimen was visible permitted the melting point to be determined when sharp features on the specimen surface became rounded; it also indicated that blackbody conditions did not prevail. By standardizing against the melting point of molybdenum, the observed melting temperature was corrected by the following form of Wien's Law: in which T is the true temperature, To is the observed temperature, and K is a constant characteristic of the filament geometry and determined experimentally for the molybdenum standard. The resulting corrected melting point for each alloy served as a reference temperature for the second more precise filament geometry. With a 6 to 1 depth to opening ratio, the specimen was indistinguishable from the filament interior, indicating good blackbody conditions. Using this technique, a series of specimens was isothermally treated at temperatures above and below the corrected direct reading. Incipient melting was detected by visual or micrographic examination of the specimen after cooling. This procedure was checked with specimens of pure chromium, molybdenum, and tantalum. Table I represents the values obtained, together with the solidus temperatures in the tantalum-rhenium binary system determined by the same technique. The alloy specimens were approximately 1/8 in. in diam. They were pieces of 10-g buttons melted four times in a nonconsumable tungsten electrode arc furnace on a water cooled copper hearth in 2/3 atmos of titanium gettered helium. Several sources of error are possible in such temperature measurements. Within the accuracy of the pyrometer no gradients were detectable near the specimen, and element distortion was virtually eliminated by twisting the tantalum. Compensation was made for the 1/8-in. sight glass by inserting several identical thicknesses and extrapolating to zero thickness. As a result an additional 10°C correction was added to all observations in the temperature range of 2500" to 3000°C. The principal source of error was then in the operation of the

Jan 1, 1961

By L. F. Mondolfo

An investigation of the relationship between properties of the elements and type of binary diagram formed was conducted. It was found that, for each type of equilibrium diagram, the factors for the size, valence, electronegativity, period, melting point, entropies of fusion, and sublimation calculated for each pair of elements cover a range of values. However, these factors show sufficient relationship to the equilibrium diagram so that the correlation of several of them can be used to predict the type of diagram formed, or at least limit the choice to only a few types. ThE goal of the metallurgist concerned with alloy development has always been to find a method that predicts the properties that can be obtained when a certain metal is added to another one. In most cases a qualitative predictiton of properties can be made if the equilibrium diagram is known. However, this means that for new metals the alloy development has to start with the experimental determination of the equilibrium diagrams. Because this determination is at least as complicated and time-consuming as the determination of the properties themselves, most alloy development has taken place by trial and error, and the study of the equilibrium diagrams has followed rather than preceded the creation of new alloys. Alloy structures and properties depend on the interaction between electrons and a complete knowledge of these interactions would permit prediction of structure and properties of alloys. Unfortunately direct measurement of these interactions is extremely difficult and somewhat doubtful and only properties that depend on them can be measured easily and with certainty. Study of the relationship between properties of the elements and equilibrium diagrams is not new. Besides the well known Hume-Rothery rule of the necessity of an atomic diameter fit within 15 pct for extensive miscibility in the solid, and the wide knowledge of the effect of such factors as size, electronegativity, electron-atom ratio on solid state features,"' work relating to liquid state and liquid-solid reactions can be found in the literature. Of particular interest is the work by Axon,3 who investigated the effect of size and melting point on a selected number of eutectic and monotectic dia-

Jan 1, 1962

By James F. Watson, Jack L. Christian

The austenite to martensite solid state phase transformation in the 300 series austenitic stainless steels was studied over the temperature range of 788° to -423°F. The primary variables controlling this transformation are temperature, plastic strain, and chernical composition. Consequently, temperature effects were studied by measurements at 78", -100°, -320°, ad -423°F; plastic strain was controlled by cold-rolling the alloys varying amounts between 40 and 80 pet; and chemical compositions were varied by using 301, 302, 304 ELC, and 310 stainless steel alloys which exhibit varying degrees of austenite stability. The martensite contents of various alloys were correlated with several mechanical properties including yield and ultimate tensile strength, elongation, and notched tensile strength (Kt = 6.3). The yield and tensite strengths generally increased with increasing martensite content, but ) no correlation was observed between elongation and martensite content. The notched/un-notched ratio (Kt = 6.3) at -423°F exhibited a maximun at about 65 pct martensite. Attempts to correlate austenite stability (as measured by the Ms temperature) with both martensite content, and incremental increases in martensite content resulting from tensile testing were generally unsuccessful because the variable of cold Work could not be separated. As a result, only a general correlation of these variables was obtained. A (111) pole figure of austenite in a cold-rolled 301 stainless steel mas prepared an attempt to further investigate directionality as exhibited by mechan- ical properties. Yield strength was correlated with this pole figure, but ultimate and notched tensile strengths were not. 1 HE literature contains a wide variety of references pertaining to the austenite to martensite solid state phase transformation in austenitic stainless steel, see references 1 through 18. Discussions of the crystallography and kinetics of this transformation are given in references 2, 7, 8, 'and 11, while further discussions of austenite stability and hardening mechanisms are given in references 1, 3, and 10. Two important processing variables involved in this reaction are the degree of cold work and the temperature at which cold work is performed, and the nature of these effects are outlined in references 4 and 12, and 15 and 16 respectively. The latter two references deal primarily with cold rolling conducted at subzero temperatures. The effect of chemical composition on the austenite to martensite reaction was treated in detail by Eichelman and Hull, and they determined an equation for the M, temperature of this type of steel which included the effects of nickel, chromium, carbon, nitrogen, silicon, and manganese.5 Previous studies have shown that austenitic stainless steels of AISI types 301, 302, 304ELC, 310, and 301-N exhibit mechanical properties between 78" and -423"~ that are microstructure dependent, and the dependence of this microstructure on chemistry, temperature, tensile stress, and prior deformation is in general accord with previous investigations which have measured the effects of each of these variables on structure, or more specifically, the austenite-to-martensite transformation.lg The behavior of fully stable alloys, such as ATST type 310, at cryogenic temperatures is

Jan 1, 1962

By R. E. Reed-Hill, J. L. Martin

Kinking is an important deformation phenomenon in poly crystalline a zirconium. The crjlstallo-gvaphic features of the most important form of kinking have been determined with the aid of twins formed at 77°K in grains previously kinked at high temperatures. It has been .found that the kink-band boundaries correspond to walls of edge dislocations with (1150) Burgers vectors and dislocation lines parallel to (1070). The present observations imply that basal slip is an important secondary-slip mode in polycrystalline zirconium. Previous single-crystal studies13 did not veveal this mode Other evidelzc.e for (0002)(1120) slip is also presented. ThE first studies of kinking in hexagonal metals were made by orowan,1 using single-crystal cadmium wires. He suggested that this was a new de- formation mode in metals, different from ordinary glide or twinning. Next, Hess and Barrett2 studied zinc-crystal rods in compression, and were able to offer an explanation of the phenomenon described by Orowan. They concluded that kinks required no new deformation mechanism and were a special form of deformation band that developed gradually and solely from basal glide. Similar kink bands were then observed by Washburn and parker3 on zinc crystals deformed in tension at low stresses and high temperatures. In titaniun,4 kink bands associated with {1010}<1120> prism slip have been observed in coarse-grained specimens. Magnesium5 and rhenium6 have also been observed to kink in conjunction with their basal- and {1010} prism-slip systems, respectively. Yttrium has (1010) as a predominant slip plane, but no observations of kink bands were reported.7 Since no previous investigations of kink bands in zirconium have apparently been made, this study was proposed. Its aim was to determine the crys-tallographic features of a type of kink band frequently observed in polycrystalline zirconium. EXPERIMENTAL APPARATUS All tests were performed on a type TTC Instron machine. The cross-head speed usually chosen in tension or compression was 0.02 in. per min. Ten-

Jan 1, 1964

By David A. Thomas, John F. Peck

Sam Leber (General Electric Refractory Metals Laboratory)—I think that the authors should differentiate between the curved grains obtained by swaging and the crumpled grains produced by drawing. This can be seen most easily in the transverse sections of Fig. 2d, and is also apparent in Fig. 2c. This difference in structure indicates that the mode of deformation shou1d affect the texture, since the cylindrical texture should be maintained or even increased by the curved grains developed by swaging. Drawing, on the other hand, crumples the grains. This should convert the cylindrical texture into a normal fiber texture. This has been substantiated by a comparison of tungsten wires fabricated by similar drawing and swaging schedules. Although cylindrical textures have been detected in drawn iron wires, they were weak in comparison to tungsten wires which included swaging as part of the fabrication process. It should also be noted that large curved surfaces developed by swaging are concentric with the surface. The postulated (100) surface of these crystals would be confirmed by a (100) cylindrical texture, as was observed in tungsten. The preservalion of the (100) cylindrical texture by swaging would maintain the <100> direction in the radial position required for easy flow. This might provide a partial explanation for the decreased rate of work hardening observed in the swaged wire. J. F. Peck and D. A. Thomas (authors&apos; reply) — The authors appreciate Dr. Leber&apos;s comments on the differences in textures, microstructures, and properties of swaged and drawn wires. The evidence of the prominence and persistence of the cylindrical texture in swaged bee wires seems quite consistent with our microstructural observations and interpretations. We are presently engaged in further work to correlate the development of texture and micro-structure in drawn bee metals.

Jan 1, 1962

By N. A. Tiner

A study was made of the effects of temperature, type of loading, and electric polarization on the fracturing behavior of copper and zinc coated with mercury. Copper showed an em-brittlement only in cyclic loading, whereas zinc showed an em-brittlenzent in both static and cyclic loading. The embrittle-ment of zinc in static loading was prevented by sub-zero cooling to a temperatzcre of about -70°F. The emhrittlement of both metals was sliglztly reduced by cathodic polarization of mercury. The basic processes involved in fracturing were discussed in the light of these observations. When a solid metal is in contact with certain liquid metals possessing high wetting characteristics, a weakening effect is produced, and the solid metal fractures in brittle manner at a relatively low stress. This lowering of the fracture stress generally is considered different from the stress cracking caused by a corrosive liquid environment and is attributed to the lowering of the solid-liquid interface tension at the grain boundaries.1-4 The purpose of this paper is to describe a number of observations on the special features of fracturing of copper and zinc coated with a liquid mercury film, and to analyze the basic processes involved in fracturing in the light of these observations. EXPERIMENTAL OBSERVATIONS I) Effect of Type of Loading—The evidence appears to indicate that in static loading, metals usually fracture by the initiation of microcracks in the interior preferentially at the grain boundaries or at the intersection of slip bands.&apos; In cyclic loading, cracks develop on the surface within the active slip zones, and gradually propagate with increasing num- ber of cycles.6&apos;7 Because of this difference in the manner of initiation of cracks, a series of bare and mercury coated copper and zinc specimens was subjected to static and cyclic loading, and their fracturing behavior was examined. The specimens were machined to 0.25 in. in diam and 1 in. in length from a high-purity commercial bar stock, and annealed at an appropriate temperature. Mercury was applied to the surface of the specimens by rubbing with cotton wool soaked in a saturated solution of HgCl2 or by etching with a dilute solution of HC1 and rubbing with purified mercury and by washing in water. The static tension load-extension curves were obtained by means of a Riele Screw Power Universal Testing Machine. The room-temperature load-extension curves for copper and zinc are shown in Fig. 1. The deformation behavior of copper, as judged from the general configuration of the load-extension curve, was not affected by mercury coating. The maximum load to fracture and the elongation at the maximum load were practically the same for both specimens. The mercury coated copper, however, showed somewhat less localized necking and had smaller reduction of area than the uncoated metal. The behavior of mercury coated zinc was radically different from the behavior of uncoated metal. The load-extension curves were the same at the

Jan 1, 1962

By C. S. Smith, W. M. Williams

THE quantitative study of grain shape in three dimensions has been a difficult one from the practical standpoint. Experiments on grain shape have usually been based on indirect observations of two-dimensional metallographic samples or on grains separated by intergranular corrosion or fracture. The latter method was used in particular by Deschl in 1919 in observing the shapes of ß-brass grains which had been separated with mercury. The similarity in detail of shape and packing that exists between bubbles in a soap froth and metal grains was noted by Desch who remarks that: "Surface tension has an. important share in determining the form of the crystal grains in a solidifying metal and such grains have a tendency to assume the shape of foam cells." More recently the relation between grain shape and grain growth has been studied by Harker and Parker.&apos; The importance of surface tension forces in determining microstructure has been discussed by Smith," and an analysis of the topologi-cal rules that apply to such structures has been made by the same author.&apos; Biologists have made valuable contributions to the general problem of shape and form in an assembly of space-filling cells subject to surface tension forces. Particular mention must be made of the extensive researches of Lewis5,8 on botanical and anatomical tissues, and Matzke and Nestler,7,8 who have made painstaking studies of bubble shapes in different kinds of foam. The present paper introduces a new method of studying individual grains in particular alloys—a method which may well find use in other metallurgical researches, and which seems also to be applicable in biological problems. Metal Grains in Three Dimensions The individual grains in a piece of metal or the bubbles in a soap froth must satisfy two conditions —they must be in juxtaposition so as to fill space and their interfaces must conform to the laws of surface tension. If a further restriction is imposed, namely, that only one type of polyhedron be used, then the sole possibility is an assembly of "minimal" tetrakaidecahedra," each polyhedron having eight doubly-curved hexagonal faces and six plane quadrilateral faces, the angles between adjacent faces being 120". Such cells could be stacked on a body-centered cubic lattice and would be quite stable. For many years it was believed that soap bubbles actually possessed the shape of this ideal body, and the hypothesis was the starting point for several investigations on the shapes of soap bubbles, biological cells, and metal grains. These investigations have shown, what might have been obvious in the beginning, that if the condition of symmetry is relaxed the tetrakaidecahedron is almost never found. If we retain only the rule that all contacts should be in local surface tension equilibrium and that the assembly should fill space, metal grains may then take a nearly infinite variety of shapes and no single one may be regarded as an archetype. These two conditions, which are fully discussed in one of the previously mentioned papers,&apos; lead us to think of a typical grain in an annealed metal as having the following characteristics: 1—A grain may have any number of faces, but usually between nine and eighteen. The faces (each of which is, of course, shared by two grains in the assembly) may have any number of edges, but usually between four and six. Pentagons are by far the most frequent. 2—In the assembly of grains each edge is shared by three faces and by three grains. Each vertex is a point shared by four grains, six faces, and four

Jan 1, 1953

By T. J. Whalen and Michael

The grain shape of the carbide in nickel-bowled ad cobalt-bonded titanium carbides was studied by microgiaphic examination, and the influcence of sintering atmosphere, sintering substl-after, ami the amount of metal binder on the grain shape was determined. If was found that the Carbide grain cross sections in the nickel and cobalt cermets ranged from round to angular, depending on the sintering conditions. The spheroidization of the carbides in both cobalt-bonded and nickel-bonded titanium carbides may be attribicted to oxygen. In the course of studies on titanium-carbide base cermets, various investigators have reported on the shape of the carbide grains, and it was noticed that grain shapes were obtained which were either spheroids, or polygons with rounded or square edges. It was also noted that the shapes of the carbide grains changed with time or composition. skolnickl showed that the titanium-carbide grains. after infiltration in vacuum with nickel tended to spheroi- dize with time. The titanium-carbide skeleton was located on a beryllia plate during infiltration. Gur-land,&apos; who studied the microstructure of titanium carbide-cobalt compacts, showed that the carbide grains are round after 1 hr at 1450oC in a hydrogen atmosphere and angular after 7 hr at the same temperature. Goetzel3 has found that the carbide grains in compacts with a high binder content. 40 to 60 pet. tend to be spheroidized. whereas Blumenthal and silverman4 pointed out that the higher binder contents could yield either round or rectangular grains with rounded edges. depending on the nature of the binder. It is the purpose of this paper to present experi-

Jan 1, 1961

By D. S. Tomalin, D. F. Stein

The effect of reducing oxygen to low concentrations on the fracture of high-purity iron single crystals has been examined at 78° and 20°K. It is found that iron single crystals grown by the strain-anneal method usually contain a few occluded grain boundaries which may become embittled in the presence of oxygen, thereby nucleating cleavage fractures. High purity with respect to interstitial elements was found to inhibit twinning and evidence is presented for an orientation dependence of the resolved yield stress. Deformation occurred by slip rather than twinning at both temperatures of testing with elongations of as much as 9 pct at 20°K. THE fracture properties of iron single crystals have been observedl-3 to be a function of temperature, orientation, and purity. Allen, Hopkins, and McLennan1 demonstrated that at 78°K iron single crystals became increasingly brittle as the tensile axis approached the (001) pole of the stereographic unit triangle. Iron crystals with the tension axis near a (001) pole were completely brittle and orientations near the (011)-(111) boundary were very ductile, achieving a 100 pct reduction in area prior to fracture. Later work of Biggs and pratt2 and of Edmondson3 demonstrated that by reducing the carbon content of the single crystals the transition between brittle and ductile failure at 78°K could be shifted to orientations nearer the (001) pole. Ed-mondson went further and pointed out that any mechanism which tended to increase the yield strength of the iron (i.e., carbon addition, pre-strain) also increased the tendency for brittle behavior at 78°K. Thus by a reduction of carbon content Biggs and Pratt were able to obtain ductile behavior to within 20 deg of the (001) pole, and Ed-mondson was able to obtain ductile behavior to within 26 deg of the (001) pole. Edmondson&apos;s material had a total interstitial content (carbon, oxygen, and nitrogen) of approximately 60 ppm and, although Biggs and Pratt reported no analysis, indications were that their iron contained comparable impurities. Stein, Low, and seybolt4 purified iron single crystals to a total carbon, oxygen, and nitrogen content of approximately 20 ppm. They observed a lowering of the yield stress with this increased purity, and thus one might have expected an observation of increased ductility. Although they tested specimens of orientations which the previous workers had indicated should be ductile, the crystals failed at a 78°K in a brittle manner with little elongation. Stein noted,&apos; however, that about 90 pet of the failures could be traced in origin to occluded grains. Allen et al.1 and Edmondson3 do not report examination of their cleavage surfaces, but Biggs and pratt2 reported that microscopic examination of the cleavage surfaces of many of their specimens revealed the presence of small occluded grains. Honda and cohen6 and Keh7 have also observed the initiation of fracture at occluded grains in iron single crystals. Therefore, the additional complication of occluded grains must be considered in studying the properties of iron single crystals and the origin of fractures determined if the ductility exhibited by the crystals is to be considered meaningful. Various investigators8-12 have studied the effects of impurities on grain boundaries in high-purity polycrystalline iron. Rees and Hopkins10 showed that the addition of oxygen to low-carbon (0.002 pet) iron weakened the grain boundaries, causing a shift from transcrystalline to intercrystalline fracture and a progressive decrease on the brittle-fracture stress with increasing oxygen content. In addition, it has been shown by Low and Feustel11 that the addition of carbon to polycrystalline iron containing oxygen eliminated grain boundary brittleness. Thus, oxygen can embrittle grain boundaries in high-purity polycrystalline iron, but the addition of an appropriate amount of carbon can eliminate the oxygen-induced brittleness. The oxygen content (19 ppm) of the iron "single crystals" employed by Stein el al. was large enough to suspect impurity effects at the occluded grain boundaries. Allen et al.1 Biggs and pratt,2 and Edmondson3 may have masked any occluded grain problem in their specimens considering the relatively high carbon levels they employed. stein13 demonstrated that the addition of as little as 0.9 ppm C to previously purified (less than 5 x 10-3 ppm C) "single crystals" would increase the elongation from a few percent to more than 20 pet at 78°K and the fracture was not associated with grade boundary initiation.

Jan 1, 1965

By T&apos Ke, ing-sui

THE subject of recrystallization and grain growth has been much studied and the literature on this subject is numerous. Such studies have been mostly carried out by metallographic examination of X ray methods. Since recrystallization and grain growth involve elementary atomic processes, their mechanism can best be elucidated by a study of some properties which can be readily traced back in terms of such atomic processes. Prior to a detailed quantitative study, however, it is necessary to explore first the possibility and practicability of utilizing any particular property for obtaining the desired information. We have pointed out in a preceding article&apos; that the internal friction of cold-worked metals is extremely high during recrystallization and it drops abru~tlv once the recrystallization is complete. ~reviois work has also shown that the viscosity of grain boundaries in a recrystallized specimen at a given temperature is raised by grain growth.&apos; It seems thus that the measurements of internal friction may furnish a useful tool for the study of the mechanism of recrystallization and grain growth in terms of elementary atomic processes. The purpose of this paper is to report results of a study along this line. We will demonstrate that the internal friction method does give results in agreement with those furnished by conventional metallographic examinations. Once such a correlation has been established, we will be in a position to take further steps to achieve new information which cannot be achieved by conventional methods. The measurements of internal friction were made using apparatus and procedures similar to those used in the preceding article. All the measurements were made under such a small stress level that the internal friction is independent of stress level. The frequency of vibration is, unless mentioned otherwise, about one cycle per second in all cases. Internal Friction and Recrystallization Complete Recrystallization Temperature: Fig. 1 shows the internal friction curve during annealing of a few metals: aluminum, alpha brass and iron. These curves were determined in the following manner. In the curve for aluminum, internal friction measurements were performed upon. 99.991 aluminum subjected to 95 pct reduction area. The internal friction was first measured at room temperature. The specimen was then annealed at 50°C

Jan 1, 1951

By C. Wert, D. Keefer

The results of this study indicate that sudden increases in aging temperature lead to reversion phenmena in carbon in the a, iron system. These phenomena are thought to be associated with the dissolution of carbide precipitates. Reversion is studied with respect to three variables: 1) Specimen grain size, 2) the initial amount of carbon in solution, and 3) difference between initial and final aging temperature. It is found that of these variables the initial carbon concentration has the greatest effect on reversion. THE solid solution of carbon in n iron has been the subject of numerous investigations throughout the past few years. Despite the great amount of effort which has been put forth toward understanding this system, however, there persist a number of interesting aspects of the system which are open to further research&apos; Studies Of the precipitate which forms as a result of aging a supersaturated solution of carbon in a, iron appear to be particularly interesting. The present work is an attempt to determine certain

Jan 1, 1960

By B. Post, D. Moskowitz, F. W. Glaser

Lattice parameters of various hafnium compounds, two borides, a carbide and a nitride were determined. Some physical properties were measured and comparisons with the properties of the corre-sponing zirconium compounds were drawn. A LTHOUGH borides of transition metals have A been extensively investigated in recent years, there are few references in the literature to borides of hafnium. This is not surprising, in view of the extreme scarcity and great cost of the purified metal. Becker&apos; reported the existence of a boride, carbide, and nitride of hafnium; he listed the formulas as HfB, HfC, and HfN. However, in his work no mention was made of chemical analyses of the reaction products. In this paper results of a study of various hafnium compounds, including borides, carbides, and nitrides, are reported. It was expected, of course, that these compounds would closely resemble their zirconium analogues, which have previously been extensively investigated. Three borides of zirconium are known: ZrB,² ZrB,² and ZrB212.4 In addition, one carbide, ZrC,5 and one nitride, ZrN,5 have been reported. It should be noted that ZrB and ZrB12 are stable phases only in relatively high-temperature regions, unlike ZrB2, which is stable from room temperature to its melting point." It was felt that hafnium would yield corresponding borides, carbides, and nitrides with similar stability ranges. Experimental Procedures and Results A quantity of hafnium metal that was better than 97 pct pure, with zirconium as its major impurity, was furnished by the Argonne National Laboratories. The boron powder used was approximately 96.5 pct pure. In general, the procedure involved mixing the metal and boron powders in the desired proportions, and subsequently hot pressing them. The resulting specimens were analyzed chemically and phases present were identified by X-ray diffraction methods. A Philips Norelco Geiger counter spectrometer was used for identification of components and for measurement of lattice constants. Filtered copper radiation was used for all X-ray work. Electrical resistivity and density measurements were carried out at room temperature. The stable diboride, HfB2, will be described first. Stoichiometric quantities of boron and metal were heated to approximately 2000°C during hot pressing. The reaction product was shown by X-ray diffraction methods to be isomorphous with ZrB2 (space group Dlgh; P6/mm). Values of lattice constants of HfB2 compared with those of ZrB2 are shown in Table I. The calculated density of HfB2 is 11.2 g per cc, compared with a measured (pycnometric) value of 10.5 g per cc. HfB2 specimens prepared under a wide variety of conditions (including variations in initial Hf-B ratios) showed only insignificant variations in lattice constants, indicating a very narrow range of homogeneity. Like ZrB2,7 HfB2 is an excellent electrical conductor. The resistivity at room temperature of hot-pressed samples, approximately 85 pct dense, is 12 microhm-cm. This compares favorably with the electrical resistivity of 10 mi-

Jan 1, 1954

By B. R. Banerjee

MATERIAL used throughout this investigation was high-purity aluminum (99.998 pct). The 1/2-in. cubes were cut out of a cold-rolled slab and annealed at 550°C for 1 hr before deformation. The single crystal specimen was 1 in. in diam x 0.33 in. thick, cut from a cylindrical crystal produced by cooling at about 55°C per hr in a furnace which had a convenient gradient of about 10°C in every 4.5 in. vertical crucible length. Specific data on the ten specimens studied are summarized in table I. Three types of deformation were employed: (I) compression in a hand-operated hydraulic press; (2) impact with a 7-lb sledge hammer; and (3) rolling, using a wedge-shaped specimen&apos; to obtain a gradient of deformations varying from 0 to 50 pct along the length of the wedge. Specimens were either deformed at room temperature, or first cooled in a freezing mixture of dry ice and ether at a temperature of —72°C and then deformed between steel blocks cooled with dry ice. The specimens deformed at the low temperature were ground and polished through 000 emery paper and wheels impregnated with alundum and alumina No. 1. During this entire procedure the specimens were dipped frequently in the freezing mixture of dry ice and ether in order to maintain constantly a frosty surface as insurance against overheating. All specimens were given a final electrolytic polish, using two different electrolytes* to insure that the surface effects observed were not char- acteristic of the polishing technique. With both electrolytes, the annealed specimens gave even surfaces with good polish. Several standard etchants were tried without success. The best results were obtained with an immersion etchant, developed in this connection, containing: hydrofluoric acid, 4 parts; nitric acid, 1 part; glycerine, 3 parts. Discussion of Results Typical strain markings have been observed within deformation bands, as shown in figs. 1, 2, and 4. By stereographic plotting of metallographic measurements, the strain markings within a deformation band in a single crystal of aluminum deformed by compression were found to be traces of (111) planes within a maximum scatter of 6". The edges of the deformation band were found to be traces of the (100) planes also within the maximum scatter of 6" (in agreement with previous workers). At 30 pct deformation, this scatter was considered quite normal because of the fragmentation and rotation of the crystal. This solution, based on the traces on one plane of observation is not unique, but as the planes were observed to be those normally and logically to be expected, further work in this regard was not felt to be necessary. The study of strain markings in a wedge-shaped specimen, rolled to obtain a gradient of deformation from 0 to 50 pct, revealed prominent strain markings at 25 pct reduction in thickness (fig.5). Faint and weak strain markings were visually observable up to a minimum reduction in thickness of about 12 pct. Since strain markings have been observed in other face-centered cubic metals after much smaller deformations;1, 2 and since the rate of recovery in aluminum is high, it is believed that, at lower deformations, self-recovery removes the localized strains at the slip interfaces, thus removing the source of the etching effects that give rise to strain markings. At high magnifications, strain markings sometimes seem to appear as very thin, light-banded re-gions bounded by a pair of dark edges. This so-

Jan 1, 1951

By E. J. Rapperport, E. D. Levine

The boundaries of the (a +ß) field in the Al-Li system were determined between 150°and 550°C utilizing quantitative metallography and lattice-parameter measurements. The solubility of lithium in aluminum decreases from 12.0at. pct Li at 550°C to 5.5 at. pct Li at 150°C. P Al-Li is saturated with aluminum at 45.8 at. pct Li and has this boundary value constant over the temperature range 150°to 550°C. THE solid solubility of lithium in aluminum has been determined by several investigators, 1-6 but, as shown in Fig. 1, there is little agreement among the various determinations. The earliest investiga-tions&apos;-&apos; are suspect because of the use of impure materials. Although high-purity materials were employed in more recent work,4&apos;5 the experimental techniques may have led to contamination of the specimens. Probably the best work has been that of Costas and Marshall,6 who obtained close agreement between results obtained by two independent phase-boundary techniques: electrical resistivity and mi-crohardness. No detailed studies of the solubility of aluminum in the bcc ß phase, Al-Li, have been reported. Cursory investigations1,2,6 have indicated only that the (a+ß) -p boundary lies between 40 and 50 at. pct Li and is relatively independent of temperature. The present work was undertaken in order to provide an independent check on Costas and Marshall&apos;s determination of the solubility of lithium in aluminum, to extend knowledge of this solubility limit to temperatures below 225°C, and to make an accurate determination of the solubility of aluminum in Al-Li. EXPEFUMENTAL Alloy Preparation. In view of the difficulties encountered in previous investigations of the A1-Li system, close attention was paid to the use of methods of alloy preparation and treatment that would minimize contamination. Aluminum sheet (99.99 + pct Al) was vacuum-induction melted in a beryllia crucible to remove hydrogen. Lithium (99.9 pct Li) was charged with pre-melted aluminum into a beryllia crucible, in a helium-filled drybox. The crucible was sealed in a Vycor tube and transferred from the drybox to an induction furnace. Melting of alloys was performed by induction heating in a helium atmosphere. Solidification was accomplished by means of a suction apparatus, shown in Fig. 2, in which the alloy was forced by changes of pressure into a 3/16-in. inside diam closed-end beryllia tube. This technique produced rapid solidification of a small portion of the melt, resulting in alloys with a high degree of homogeneity. Typical lithium distributions are presented in Table I. Transverse sections 1/8 in. long were cut from the alloy rods, and each section was split in half longitudinally. One half of each section was analyzed for lithium, and the opposing halves were employed for phase-boundary determinations. Lithium contents were determined by flame photometry with an accuracy of 1 pct of the amount of lithium present. Thermal Treatments. Homogenization and equilibration heat treatments were performed in electrical-resistance furnaces with temperatures controlled to ± 2OC. Calibrated chromel-alumel thermocouples were employed to measure temperature. Homogenization was performed in helium-filled l?yrex tubes for 1 hr at 565°C. The encapsulated specimens were then transferred directly to furnaces maintained at lower temperatures for equilibration. Equilibration times were 2 hr at 550°C, 8 hr at 450°C, 27 hr at 350°c, 90 hr at 250°c, and 285 hr at 150"~. These times were chosen on the basis of conditions employed by previous investigators. Alloys were quenched from the equilibration temperatures by breaking the capsules into a silicone oil bath. By performing all possible operations either in sealed capsules or in a helium-filled drybox, the specimens were given minimum exposure to the atmosphere. Quantitative Metallography. Metallography of Al-Li alloys is difficult because of the atmospheric reactivity of the ß phase. It was found possible, however, to prepare surfaces of good metallographic quality by preventing contact with moisture during preparation. Grinding through 4/0 paper was performed in the drybox. The specimens were then transferred under kerosene to the polishing wheel. Three polishing stages were employed: 25-p alundum with kerosene lubricant on billiard cloth, 1-µ diamond paste on Microcloth, and 1/4-p diamond paste on Microcloth. Between stages the samples were cleaned by rinsing in trichloroethylene and buffing

Jan 1, 1963

By J. Gurland

The effects of variations of carbon content on the constitution and properties of sintered WC-Co alloys were studied. The grain growth of tungsten carbide during sintering was measured and it was shown that it takes place mainly by solution and reprecipitation of the carbide in and from the binder at the sintering temperature. It was found that the decomposition of W3C03C by carburization during sintering is responsible for the formation of very large grains. THE properties of sintered WC-Co alloys are critically dependent upon their final composition and structure. Slight changes of cobalt and carbon contents and small variations of grain size result in marked changes of mechanical properties and performance of products. Previous investigators have studied the microstructure as a function of composition&apos; and have dealt with the influence of cobalt upon properties.&apos; The present work is concerned with the effect of carbon content upon constitution, microstructure, and grain growth during sintering, as well as upon the physical properties of sintered compacts. Phase Boundaries at the Sintering Temperature The WC-Co section through the ternary diagram W-Co-C has been studied by Wyman and Kelley,&apos; Takeda,V andford and Trent," and Rautala and Norton." Two phases, namely WC and a cobalt-rich solid solution (P), appear in the sintered structure if the carbon composition corresponds very nearly to the theoretical carbon content of WC (6.12 pct C). But small deviations from the ideal carbon content will bring about the occurrence of either graphite or the double carbide W,Co3C (7) . The 7 phase was long believed to be metastable, this conclusion being based mainly on the work of Takeda. More recent studies have shown that it is a stable phase of the ternary system,"5 but the actual phase boundaries have not been established and there has been some discussion as to whether or not the 7 phase occurs at some stage of sintering in the fully carburized alloys." In view of this uncertainty it was thought advisable to undertake an investigation of the phases present during the sintering of WC-Co alloys. Commercially available tungsten, cobalt, and carbon powders were used in the present study. A typical analysis of impurities in a sintered compact is reported in Table I. The desired carbon compositions were attained by varying the amount of carbon added to the tungsten during carburization and controlling the composition during sintering by packing the compacts into beds of mixed alundum-carbon powders of suitably selected ratios. The alloys were sintered in a hydrogen tube furnace at 1400°C, then brought to equilibrium at the temperature under investigation and quenched in water. The high temperature phases were identified by metallographic and X-ray diffraction techniques. The samples were etched with a 10 pct solution of alkaline potassium ferricyanide. The phase boundaries, established by metallo-graphic examination, are shown in Fig. 1, which is a vertical section through the ternary diagram at 16 pct Co. The temperatures of the invariant planes, at 1298" and 1357°C were established by Rautala and Norton. The vertical section shows that the three-phase field, WC + 7 + L, extends into the two-phase field, WC + L, but does not include the stoichiometric composition of WC. In practice this means that the 7

Jan 1, 1955

By W. D. Robertson, Raymond C. Boettner

A study was made of the change in density during the first (transient) and second (linear) stages of the creep curve of polycrystalline copper as a function of 1) stress, 2) temperature, 3) plastic strain, 4) impurity and atmosphere effects, and 5) structure, including single crystals. Voids were not observed in single crystals strained 15 pct at 500°C, or in a polycrystal-line aggregate produced by recrystallizing a single crystal, within the limit of sensitivity, Ae/e = 1 x 10-4. It appears that voids are heterogeneously nucleated at grain boundaries by an insoluble phase, or phases, which can be removed by directional solidification. The principal controlling mechanism of void growth appears to be condensation of vacancies at grain boundaries. Vacancies are transported to a boundary and condense as a consequence of the tensile stress component across the boundary, which depends on the orientation and configuration of the boundary plane and on boundary shear across ledges and other irregularities. The ultimate source of vacancies is the free surface and diffusional transport is by way of the boundary plane. PREVIOUS investigations have dealt with the nucle-ation of voids at grain boundaries under creep condition~&apos;-~ and with the connection between grain boundary voids and subsequent brittle fracture.5-7 Growth of voids during the creep process, particularly in the transient and linear stages of creep, has not been studied with the same intensity. Therefore, it seems pertinent to investigate the process of void growth with respect to the related creep curve, and the morphology of growing voids with respect to the structure.

Jan 1, 1962

By J. W. Pugh, J. D. Nisbet

THIS study of the ternary has been made as one phase of a metallurgical investigation which began nearly four years ago in the General Electric Company&apos;s Research Laboratory in Schenectady, N. Y. The objective of this program is the discovery of new metallurgical information which will lead to the development of better high-temperature materials. Combinations of the four pure base elements—iron, chromium, nickel, and cobalt—are being studied at the present time. It is essential in an investigation such as this to know as much as possible about the constitutional diagrams involved. The study of the iron-chromium-nickel system has been made to this end. Preliminary Explanation of Experimental Procedure: In all, fifty-five alloys at steps of 10 at. pct were made for the investigation of this ternary. Several ternary alloys in the chromium rich corner had to be omitted because their extreme brittleness made testing impractical. All alloys were vacuum melted with hydrogen reduction and centrifugally cast. The apparatus and technique of this process has been described in detail by Nisbet.1,2 The purity of the alloys prepared in this way is considered to be quite good. Impurities are listed as follows: Pct Carbon.............................0.02 Oxygen................................0.02 Nitrogen.........................0.005 Magnesium..................0.03-0.05 Sulphur...........................trace Hydrogen....................trace Phosphorous..................trace Silicon........................ trace After casting, all samples were given a homo-genization treatment which consisted of holding them for 15 hr at 1150°C (2100°F) and water quenching. Testing was begun with the samples in this condition. The tests employed in the study of this system were (1) dilatometer, (2) hardness versus aging temperature, (3) tensile strength and elongation versus temperature, (4) microstructure analysis, and (5) electrical resistance versus temperature. Dilatometer tests were made at the rather rapid heating rate of 1093°C (2000°F) in one hour on a Bristol-Rockwell type instrument. Hardness data were taken on specimens cooled from 204", 427", 649°, 760°, 871°, 982°, and 1093°C under conditions which are thought sufficient to bring the specimens to equilibrium in all but the cases of the very sluggish transformations. Electrical resistance data for several specimens were taken for both heating and cooling conditions in a vacuum furnace especially designed for this work by D. W. Bainbridge, formerly of this laboratory. Provisions were made for heating and cooling standard specimens at a constant rate, while autographic records of resistance and temperature were made simultaneously. Micrographs of all the alloys were made in the quenched condition. Some question may exist as to how such physical values as hardness, tensile strength, and elongation were interpreted to indicate a change in phase. Original data were recorded on physical property versus temperature graphs, each of which was made from the data of a single alloy (fig. la). From these, another series of graphs were plotted with the physical property as a function of composition for constant temperatures (fig. 1b). Sharp deviations in the slope of these composition versus hardness curves often indicate a change in phase. The example of fig. 1 will serve to describe this experimental technique. The plotting of a single point from graph "a" to graph "b," and finally to the phase diagram "c," is illustrated. The location of the point on graph "b" is indicated as point (1). If all the alloys of the A-B binary system were solid solutions at temperature X, the hardness in this curve would be expected to rise at a fairly even rate as A is diluted with B to a maximum at some intermediate value between A and B, as

Jan 1, 1951

By J. W. Pugh, J. D. Nisbet

F. B. Foley—The use of data published by Wever and Jellinghaus in 1931 to fix boundaries of the sigma phase in the Fe-Cr system, in the face of the author&apos;s own references to the suggestions of Bradley and Goldschmidt, Aborn and Bain, and Hougardy that the phase is much more extensive, and the very much more accurate work, which weighs heavily in favor of these suggestions, of Cook and Jones, published in 1943 and evidently disregarded by the authors, makes their derived ternary diagram, especially fig. 15 for 400°C, quite inaccurate on the Fe-Cr side and affects the extent of phase boundaries in the most controversial and important part of this ternary system. In commercial Fe-Ni-Cr alloys the occurrence of sigma has been observed time and time again at lower chromium contents than that of the 24 pct Cr, 16 pct Ni, 60 pct Fe alloy which is the lowest permitted by fig. 15 of practically carbonless metal. Newel1 reports sigma in 27 pct Cr-Fe even with some carbon present to be one of the greatest detriments to its extensive application, whereas Pugh and Nisbet set a low limit of 36 pct Cr for sigma in the binary Fe-Cr system. J. J. Heger—The diagrams presented by the authors do not agree with observations made on commercial Fe-Cr and Fe-Cr-Ni alloys, nor do they agree with two recent investigations made on the Fe-Cr and the Fe-Cr-Fe systems. I refer first to the investigation made by Cook and Jones1&apos; on the sigma region of the Fe-Cr system. On the basis of their results which were published in 1943, Cook and Jones established new boundary limits for the sigma and the alpha plus sigma regions. These new limits have been accepted and are incorporated in the Fe-Cr diagram that appears in the 1948 edition of the Metals Handbook. This diagram is shown here as fig. 34. As will be noted, the boundary limits of the alpha plus sigma region in this diagram extend to much lower chromium contents than do those in the diagram presented by the authors in fig. 2. These new limits indicate that sigma phase should form in an Fe-Cr alloy containing 26 pct Cr, and experience with commercial alloys confirms this finding. Indeed, recent studies on a commercial Fe-Cr alloy containing 17 pct Cr have shown sigma phase to be stable in this alloy at 550°C. I recognize that the authors&apos; work did not include studies on the sigma region; however, I believe this is a serious omission because sigma phase may profoundly affect the physical properties of these alloys and should be evaluated in any investigation which attempts to relate physical properties to the equilibrium diagram. The second investigation to which I refer is that made on the Fe-Cr-Ni system by Rees, Burns, and Cook,&apos;&apos; who used pure alloys and employed heating 17 W. P. Rees, B. D. Burns, and A. 3. Cook: Journal Iron and Steel Institute. (July 1949) 162, Part 3. p. 325. times that extend to 200 days. These investigators published their results in July 1949 and from these results constructed isothermal sections at 800" and 650°C. The isothermal section at 650°C is shown here as fig. 35. This diagram indicates sigma phase should form in a pure 18 pct Cr-8 pct Ni alloy. Although sigma phase has not been observed after 10,000 hr at 1200°F in commercial 18-8 alloys containing carbon and nitrogen, it has been observed under the same conditions in 18-8 alloys modified with titanium and columbium, both of which serve to reduce the effect of carbon and nitrogen. This section and the one at 800°C suggest that the constant iron sections which are presented by the authors, should be considerably altered, if they are to represent an accurate picture of the system. A few of the suggested alterations are as follows: In fig. 9, the section at 50 pct Fe, the gamma plus sigma region should be widened, not narrowed at 800" and 650°C. In fig. 10, the section at 60 pct Fe, the gamma plus sigma region should be widened at 800° and 650°C. In fig. 11, the section at 70 pct Fe, an alpha plus sigma, an alpha plus gamma plus sigma, and a gamma plus sigma region should be added. In fig. 12, the section at 80 pct Fe, the alpha plus gamma region should be widened at 800°C. In fig. 13, the section at 90 pct Fe, the alpha plus gamma region should be widened at 650° and 800°C. Undoubtedly, the chief reason for the discrepancies between the authors&apos; data and those of Rees, Burns, and Cook is that the authors did not employ long enough heating times to allow for transformation. In this connection, I wish to warn that transformations in these alloys, particularly transformations at temperatures below 800°C, are extremely sluggish and may require a year or more to approach completion. Therefore, unless extremely long heating times are employed or steps are taken to accelerate these transformations by such means as mechanical working, the results will not yield an accurate picture of the alloy system. Certainly, an accurate picture is needed for the development of better high-temperature materials. E. J. Dulis-The purpose of this work is not clear. If an improvement of the ternary equilibrium diagram of the Fe-Cr-Ni system was wanted, it seems logical that testing techniques superior to those previously used would be a prime requirement. To approach equilibrium in this system, long holding times are needed; a fact established long ago but apparently ignored by the present authors, who used the continuous heating and cooling tests in equilibrium studies. A publication on the same system by Bradley and Goldschmidt6 was criticized by Monypenny in a

Jan 1, 1951

By R. Silverman, H. Blumenthal

It was found that despite the similarity of chemical analyses of different titanium carbides used as base materials for cermets, the physical properties, especially transverse-rupture strengths, of test bars were different. Hence this metallographic study attempts to link physical properties to micro-structures. It is shown that microstructure, grain shape, and grain growth are functions of three interrelated factors: 1—powder production procedure, 2—surface conditioning of the particles, and 3—impurities either contained in the original powder or acquired during ball milling. An explanation is offered for the "coring effect," long observed, but heretofore of unknown origin. The explanation is based on assumption of an oxide film and on chemical analyses which substantiate these findings. TITANIUM carbide has become in recent years a material of great interest in the high temperature field. Consequently, many manufacturers in the United States and Europe are producing titanium carbide for cermet applications as well as for additions to the well known tungsten carbide tools. All present commercial processes of titanium carbide production utilize the chemical reaction of titanium dioxide and carbon to form as nearly as possible stoichiometric Tic. This reaction is carried out in three ways: 1—in a menstruum of molten metal,&apos; 2—in the solid state, either in a protective atmosphere2 or in vacuum;" or 3—in an are-melting operation. In spite of the fact that the pure carbides obtained in these operations are almost identical chemically, the physical properties vary considerably when they are combined with a binder (Ni, Co) to form cermets. This fact led the authors to examine metal-lographically nickel-bonded titanium carbide in order to find the possible reasons for this behavior. Materials and Methods Five different titanium carbides were used in this investigation. They are identified in Table I. The first four materials were used in the as-received condition. Material E, received in lumps, was crushed to —100 mesh and carried through a flotation process in order to bring its graphite content in line with the other products. A Galagher flotation cell was used with pine oil as frothing agent. The chemical analyses of the investigated materials are given in Table 11. The binder used was carbonyl nickel of 9 to 14 microns particle size, supplied by A. D. Mackay. The materials were ball milled at a ball to charge ratio of 6:1 using procedures described under "Experiments and Results." All particle sizes mentioned are averages determined with a Fisher Sub-sieve Sizer. Test bars (lx0.40x0.16 in.) were prepared by 1—hot pressing to 85 to 95 pct of theoretical density at pressures between 1 and 1½ tsi and temperatures from 1600" to 1800°C, 2-—-cold presssing after 3 pct camphor had been added, or 3—wet pressing, both 2 and 3 at pressures between 5 and 10 tsi. All pressed bars were sintered in a vacuum of 105 to 10-6 mm Hg for 2 hr at 1350 °C. Transverse-rupture strengths were determined by breaking on a Baldwin Universal Testing Machine over a 9/16 in. span. Densities were measured by water displacement. The preparation of the specimens for micrographs was done according to Silverman and Doshna Luscz." All magnifications are at X1000. A sodium picrate electrolytic etch was used. Experiments and Results The influence of ball-milling procedure, ball-milling medium, pressing procedure, and sintering procedure on the microstructure of 80/20 — TiC/Ni were investigated. Ball Milling of Materials A, B, and C in a Steel Mill: Figs. 1 and 2 show microstructures of hot-pressed and vacuum-sintered test bars of materials A and B after the respective materials had been ball milled to 2.1 microns particle size in a steel mill and mixed with 20 pct Ni binder. Material A (Fig. 1) shows considerable grain growth. Also evident is a tendency of the carbide grains to coalesce. The density is 98 pct and the low transverse-rupture strength of 111,000 psi is probably caused by many large grains and an unfavorable packing factor. Almost all grains show a slight indication of "coring." Material B (Fig. 2), although showing grain growth, still has many small particles and a better distribution of binder and carbide due to the relative absence of the coalescing tendency. "Coring" can be observed in almost all grains. The high transverse-rupture strength of 179,000 psi and the density of 100 pct are believed to be due to the many small grains completely surrounded by the binder phase. There is also a preference to form spherical grains with material A, while most grains of material B preserve their angular shapes. Material C, of which no picture is given, stays between A and B in every respect. Rounding of some grains can be observed as well as coring, but the latter to a lesser degree than with material B. Its densification is good and the transverse-rupture strength obtained is 142,000 psi. Ball Milling of Materials A, B, C, and E in a WC Mill: When the Tic powders were ball milled to 2 microns particle size in a we mill, then ball-mill mixed with 20 pct Ni binder, hot pressed, and vacuum

Jan 1, 1956