Search Documents

By F. A. Forward, A. H. Ross, J. Halpern

IN treating carnotite ores by carbonate leaching it is often necessary to subject the ore to a prior roast. Among the advantages that may result from roasting are: 1) improvement in settling and filtering characteristics of the ore; 2) destruction of carbonaceous impurities that would otherwise contaminate the leach solution and consume carbonate reagent; and 3) substantial increase in extraction of vanadium, which is usually low when the un-roasted ore is leached. Recovery of vanadium may be an important factor in processing carnotite ores, and the fact that vanadium is usually recovered in good yield by acid leaching has often been an economic advantage over results obtained with carbonate leaching. It has been found that response of an ore to carbonate leaching, following roasting, depends primarily on its composition and on the conditions of the prior roast treatment, particularly with regard to the roasting temperature, the atmosphere maintained above the charge during roasting and cooling, and the presence of certain reagents. These factors, especially the last, virtually determine the extractions of uranium and vanadium attainable by carbonate leaching, as well as the reagent consumption on leaching, whereas adjustment of the leaching conditions has only a limited influence. These variables were examined systematically to elucidate roasting and carbonate leaching of carnotite ores and to establish a treatment yielding high recoveries of both uranium and vanadium. Tests were conducted on samples of four different Colorado Plateau ores, described in Table I. Roasting Procedure: The roasting tests were conducted in an electrically heated furnace in which the temperature was controlled to +15oC. The ore (usually a 500-g charge) was ground to —100 mesh, mixed with the desired reagent, and spread in a silica tray to a bed depth of about 1/2 in. During the roast the charge was rabbled at intervals of 15 min. To provide free access of air the furnace was usually ventilated; however, in a few experiments a controlled atmosphere such as carbon dioxide or hydrogen was maintained above the charge. Leaching Procedure: The pulp, generally comprising 500 g of ore and a 2000-cc solution containing 80 g per liter of Na2CO3 and 20 g per liter of NaHCO3, was agitated in an autoclave at 120°C, under 30 psi O2. Samples were withdrawn periodically, and the solution and ore residue were analyzed. Under the conditions employed, maximum attainable extractions were generally achieved in 4

Jan 1, 1958

By W. A. Hockings, M. E. Volin, A. L. Mular

Batch grinding tests at short times were made in a laboratory rod mill with 10 x 14 mesh quartzite in corn syrup-water mixtures of varying viscosity. The weight fraction broken and size modulus were found to be independent of viscosity up to 20 cp, but at higher viscosities breakage of the feed decreased while the size modulus increased. The mechanisms of the effect of viscosity are discussed on the basis of particle dynamics. The effect of viscosity of the suspending medium on grinding has not been accorded much attention, although both wet and dry grinding are used in bene-ficiation processes and the viscosities of water and air differ greatly. schweyerl investigated the rates of grinding of quartzite in a pebble mill with air, water and glycerol as the suspending media and found the rate in terms of new surface developed per thousand revolutions of the mill to be constant and dependent on viscosity up to 20,000 rev, but to decrease and become independent of viscosity for longer grinding times. Based on considerations of the drag forces exerted on suspended particles and on the grinding media under turbulent and laminar flow conditions, viscosity can be expected to inhibit the rate of grinding in a given system as it changes the flow conditions from turbulent to laminar. The objective of this study was to determine the effect of viscosity of the suspending fluid in the batch grinding of a homogeneous feed of uniform size for short residence times, a region of more practical interest than the long times investigated by Schweyer. In actual grinding operations, the viscosity of the fluid does not change, but the consistency (apparent viscosity) of the pulp increases with additions of fines. In this study the consistency of the pulp was not measured because it was thought that the grinding times were too short to alter the apparent viscosity appreciably.* *Minus 200 mesh quartz at 65% solids has an apparent viscosity of about 25 cp as measured by a simple consistometer. Personal communication from D. F. Kelsall to A. L. Mular. For the purposes of this study, the effect of viscosity on grinding can be shown sufficiently well on the basis of the cumulative weight fraction finer than the feed size at any time, and the size modulus, ku, of the finer than feed sizes. The parameter, ku, is obtained from a form of the Gaudin-Schuhmann equation. METHOD AND MATERIAL The grinding tests were accomplished in a laboratory rod mill 10-1/2 in. long and 8 in. bore with a 20-lb rod charge consisting of two 1-in., eight 3/4-in., eight 1/2-in., and eight 1/4-in. diam rods. The mill speed was 43.2 rpm. Charges of 400 g 10 x 14 mesh Wisconsin quartzite** were ground for times of 60, **Courtesy of Minnesota Mining and Mfg. Co. 120, 180 and 240 sec in 500 cc of fluid made up of corn syrup and water in measured proportions. The temperature of the pulp was measured immediately upon completion of grinding, and the size distribution of the quartzite was determined by a wash-wet-dry screening technique. Corn syrup was chosen because of its high viscosity and ideal viscous behavior, and also because its density is not greatly different from that of water. The viscosity of each fluid mixture was measured with an Ostwald viscometer at 25 C. and a correction was made for the temperature of the pulp according to tabulated values for sucrose solutions. The density differences were so small that they probably did not significantly affect breakage. RESULTS AND DISCUSSION The conditions of the grinding tests, computed viscosities, weight fractions finer than the feed size and values of a and ku are listed in Table I. The values of a and ku were taken from the linear portions of the log-log plots of cumulative weight fraction finer vs size for the various grinding times. The plots for tests in fluids of average viscosity 8.6 cp are shown in Fig. 1. In general all of the sets of curves were linear throughout most of the size

Jan 1, 1965

By T. D. Teimann, R. L. Stone

The rate of extraction of silica from certain Wisconsin and Minnesota taconites was investigated by autoclave digestion in sodium hydroxide solutions over the temperature range from 296° to 416°F. Rates obtained were from 7 to 254 g mol per cm2 per sec giving activation energies from 15,000 to 19.000 cal per mol. Activation energy was found to increase with increase of sodium hydroxide concentration. Digestion of different forms of quartz indicated the rate of extraction to be solely a function of surface area under similar conditions of digestion. The results of an experimental investigation on the caustic extraction of silica from certain Wisconsin and Minnesota taconites were presented in a recent publication.' It was shown that residual concentrates containing as much as 65% iron can be produced by this method. The occurrence of silica as a micro-crystalline variety of quartz with high specific surface area gave correspondingly high mean rates of extraction in solutions of sodium hydroxide. The present paper extends this previous work by presenting the results of a study of the specific rates of extraction of silica from these ores as related to temperature, sodium hydroxide concentration and variety of quartz. Calculated activation energies for the dissolution of silica are presented and some possible mechanisms are discussed. TACONITES The low-grade siliceous iron ores investigated included taconite from the Wisconsin Gogebic range and a semi-taconite2 from the Minnesota Mesabi range. These are adequately described in the former paper1 and by the U. S. Bureau of Mines. The principal iron minerals are hematite (Fe2O3) and goethite (Fe2O3 . H2O), while the gangue is essentially a microcrystalline variety of quartz. Minor amounts of other minerals are present. Typical analyses show the Wisconsin taconite to contain approximately 28% Fe and 54% SiO2 and the Minnesota semi-taconite 39% Fe and 39% SiO2. Analyses of the actual samples used are given in Table I. The taconite samples were prepared for digestion by reducing the original ore to minus 200 mesh in a Braun pulverizer. QUARTZ Three varieties of quartz were studied in the investigation: Ottawa sand, chert and chalcedony. The Ottawa sand was obtained from the Ottawa Silica Co. The chert and chalcedony came from Wards Natural Science Establishment. A minus 200 plus 400 mesh fraction of the Ottawa sand, used as a surface area standard, was repeatedly washed in hot concentrated hydrochloric acid followed by distilled water before autoclaving. The other two varieties were used directly after grinding through 200 mesh in a laboratory hammer mill. Analyses of these samples appear in Table 11. Microscopic examination of the silica samples by the oil immersion method showed that the Ottawa sand consisted of clean, uniform spheres of quartz with little deviation in size from a mean diameter of 82µ determined by a distribution count. The other two varieties consisted almost entirely of microcrystalline aggregates of quartz crystals; the aggregates ranged from 10 to 70µ. The individual crystals in the chert aggregates were estimated to be of the order of

Jan 1, 1964

By H. S. Choi, I. Iwasaki

The effect of temperature as a parameter in ore flotation has not been systematically studied, although for some ores it has been known for many years that selectivity and grade of concentrates can be improved by conditioning or flotation at moderately or substantially elevated temperatures. In 1934 Coghill and Clemmer' stated that "elevated temperature seems to make hard water more tolerable" in soap flotation, and a cursory examination of the literature indicates that some earlier investigators were aware of beneficial results obtained by floating above room or mill-water temperatures. Tartaron,2 Mitchell et aL.,3 and particularly Hamilton et al.' have shown that high pulp temperatures give high recovery and selectivity in soap flotation of fluorite from a variety of gangue minerals. As a result of the work of these and of other investigators, high-temperature flotation has been successfully applied to industrial flotation of fluorite. Falconer" stated: "The use of high temperature conditioning (above 35°C and preferably above 60°C) in connection with the soap flotation of nonsulphide ores, as covered in B. Kalinowski's French Patent No. 847,-215, Dec. 7, 1938, is claimed to provide more intense activation, better separation of values from gangue, and reduction in quantity of reagents." The various investigations quoted above clearly demonstrate the improvements to be realized by increasing the temperature at which fluorite is floated, and it is surprising that little or no information has been published on systematic investigation of the same method as applied to other ores. The present article describes comparative results obtained at room temperature and at elevated temperatures by otherwise conventional flotation of iron ores, by single-mineral flotation in the Hallimond tube, and by contact-angle measurements. It is not the purpose of this article to evaluate the commercial feasibility of high-temperature flotation of iron ores, although preliminary calculations show that the cost should not be excessive and that the gains to be realized may well outweigh the extra cost of heating the pulp. LABORATORY FLOTATION TESTS Experimental: All flotation tests reported in this article that use a laboratory Fagergren cell were made on ore A (either containing the primary slimes or deslimed at 20µ as specified) following the preparatory procedures described elsewhere- or this particular ore. Ore A contained hematite, goethite (limonite), quartz, chert, and minor quantities of magnetite. Confirmatory tests made on other ores show that the same general principles apply to ores of similar mineralogy and structure. Conditioning was performed by adding the collector, as a soap, to the vigorously stirred and heated pulp. Conditioning time was 5 min, the pulp contained 60 pct solids, and the equivalent of 0.5 Ib of fatty acid was added per ton of original (unde-slimed) ore. The pH of the pulps ranged from 6.8 to 7.1 (25°C measurement) during conditioning. The pH was adjusted in the flotation cell by addition of either NaOH or H2SO4, the values reported being those of the pulp cooled to 25°C. During conditioning and flotation the pulp temperatures were controlled within l° to 2° by immersion of Variac-controlled Calrod elements in the conditioning beaker and in the cell, and by the use of water, heated to the appropriate temperature, for transferring pulp, adjusting pulp volume, and washing. Selectivity indexes have been calculated on the same basis as those reported in the article by Cooke, Iwasaki, and Choi." Results: Table I gives the results obtained by floating deslimed ore A with pure oleic acid at 25" and 50°C, and Fig. 1 shows the selectivity indexes plotted against pH of flotation. Inspection of Table I

Jan 1, 1961

By Brahm Prakash, R. Schuhmann

Chemical conditions for flotation and nonflotation of cassiterite and fluorite with oleic acid as collector and with alizarin dyes as modifying agents were studied by means of small-scale, vacuum-flotation tests. Artificial cassiterite was prepared fot these tests by high-temperature methods, especially by crystallization from borax melts. FLOTATION test work on Bolivian tin ores some years ago led to the development of several workable schemes of selective soap flotation, but left unanswered many questions of soap-flotation chemistry.' Accordingly, the study of the activation and soap flotation of quartz just reported? was undertaken as a start toward the elucidation of some of the unanswered questions. The experimental work on quartz flotation consisted primarily of small-scale, vacuum-flotation tests in which activator and collector additions and pH were varied between wide limits. In the work to be described in this paper, the soap flotation of cassiterite and fluorite was studied by the vacuum-flotation technique developed in the previous study of quartz. Using oleic acid as collector, conditions for floating cassiterite and fluorite in the absence of modifying agents were first determined. Then the effects of barium, calcium, and alizarin dyes on the flotation of cassiterite, fluorite, and quartz were studied. Alizarin dyes were chosen for study because of the promise they have shown as selective modifying agents in the flotation of non-sulphide minerals.12,1 Also, they form a family of reagents in which there should be a systematic correlation of chemical properties with composition. As a preliminary to the study of cassiterite flotation, an investigation of the preparation of synthetic cassiterite and X ray studies of natural and synthetic cassiterite were undertaken. Experimental Methods The flotation technique and most of the reagent preparations were described fully in the previous paper.' In addition, for the present work it was necessary to prepare satisfactory stocks of clean cassiterite and fluorite and to obtain samples of alizarin dyes. Cassiterite: High-grade cassiterite from the Netherlands East Indies was crushed, sized, and cleaned

Jan 1, 1951

By Brahm Prakash, R. Schuhmann

Chemical conditions for flotation and nonflotation of cassiterite and fluorite with oleic acid as collector and with alizarin dyes as modifying agents were studied by means of small-scale, vacuum-flotation tests. Artificial cassiterite was prepared fot these tests by high-temperature methods, especially by crystallization from borax melts. FLOTATION test work on Bolivian tin ores some years ago led to the development of several workable schemes of selective soap flotation, but left unanswered many questions of soap-flotation chemistry.' Accordingly, the study of the activation and soap flotation of quartz just reported? was undertaken as a start toward the elucidation of some of the unanswered questions. The experimental work on quartz flotation consisted primarily of small-scale, vacuum-flotation tests in which activator and collector additions and pH were varied between wide limits. In the work to be described in this paper, the soap flotation of cassiterite and fluorite was studied by the vacuum-flotation technique developed in the previous study of quartz. Using oleic acid as collector, conditions for floating cassiterite and fluorite in the absence of modifying agents were first determined. Then the effects of barium, calcium, and alizarin dyes on the flotation of cassiterite, fluorite, and quartz were studied. Alizarin dyes were chosen for study because of the promise they have shown as selective modifying agents in the flotation of non-sulphide minerals.12,1 Also, they form a family of reagents in which there should be a systematic correlation of chemical properties with composition. As a preliminary to the study of cassiterite flotation, an investigation of the preparation of synthetic cassiterite and X ray studies of natural and synthetic cassiterite were undertaken. Experimental Methods The flotation technique and most of the reagent preparations were described fully in the previous paper.' In addition, for the present work it was necessary to prepare satisfactory stocks of clean cassiterite and fluorite and to obtain samples of alizarin dyes. Cassiterite: High-grade cassiterite from the Netherlands East Indies was crushed, sized, and cleaned

Jan 1, 1951

By Brahm Prakash, R. Schuhmann

Maurice Rey—It may be interesting to note that depressing effects can also be obtained from cyclic compounds other than dyes. One such compound which is a dispersing agent for carbon, pigments and other compounds is known in France by the trade name "dispergine" and in the United States by the name of Lomar P W (Jacques Wolf & Co.) Dr. Rey admits that the compound is not very selective and is similar in its action to starch and dextrin.

Jan 1, 1951

By Brahm Prakash, R. Schuhmann

Maurice Rey—It may be interesting to note that depressing effects can also be obtained from cyclic compounds other than dyes. One such compound which is a dispersing agent for carbon, pigments and other compounds is known in France by the trade name "dispergine" and in the United States by the name of Lomar P W (Jacques Wolf & Co.) Dr. Rey admits that the compound is not very selective and is similar in its action to starch and dextrin.

Jan 1, 1951

By J. J. Strohl, H. J. Schwellenbach

This paper relates the results obtained by decreasing the size of feed to a rod mill screen circuit. As would be expected, added production was gained and a finer grind with no tonnage loss was made possible. THE MacIntyre mill of the National Lead Co. has four parallel sections in which magnetic and gravity separations are made. Ore from a 5000-ton bin is fed by Hardinge constant weight feeders to a 6x12-ft open-end Marcy rod mill in each section. Rod mill discharge is bucket elevated to two 4x10-ft Tyrock screens whose oversize is returned to the rod mill. Screen undersize is pumped to Crockett separators for magnetite removal, and the Crockett tailings are sized and tabled to make an ilmenite concentrate. Minus 200-mesh material, overflowed by the Crockett and Dorrco sizers is thickened, de-slimed, and concentrated by flotation.' By 1948, the development of a successful slime flotation process and numerous improvements in the gravity circuit of the mill had increased the capacity of the available concentrating equipment. At the same time, improvements in the operating techniques of the dry crushing plant and improved feeding of the crusher by the mining department had appreciably increased the production rate per operating hour in that plant. Therefore, it was decided to take advantage of the added crusher capacity to produce a finer rod mill feed and in that way increase grinding capacity. At approximately the same time, finer screens were installed in the rod mill circuits to give finer grind and thus improve liberation of the magnetite and ilmenite from the gangue and from one another. Prior to the first part of 1948, a 3/4-in. limiting screen was used for sizing rod mill feed. The first reduction in crushing plant screen size was to 1/2 in. With this screen, the circulating load in the tertiary crushing circuit was too high and plant capacity dropped below a practical hourly rate. A 9/16-in.-sq opening screen, installed next, proved satisfac-

Jan 1, 1951

By H. J. Schwellenbach, J. J. Strohl

This paper relates the results obtained by decreasing the size of feed to a rod mill screen circuit. As would be expected, added production was gained and a finer grind with no tonnage loss was made possible. THE MacIntyre mill of the National Lead Co. has four parallel sections in which magnetic and gravity separations are made. Ore from a 5000-ton bin is fed by Hardinge constant weight feeders to a 6x12-ft open-end Marcy rod mill in each section. Rod mill discharge is bucket elevated to two 4x10-ft Tyrock screens whose oversize is returned to the rod mill. Screen undersize is pumped to Crockett separators for magnetite removal, and the Crockett tailings are sized and tabled to make an ilmenite concentrate. Minus 200-mesh material, overflowed by the Crockett and Dorrco sizers is thickened, de-slimed, and concentrated by flotation.' By 1948, the development of a successful slime flotation process and numerous improvements in the gravity circuit of the mill had increased the capacity of the available concentrating equipment. At the same time, improvements in the operating techniques of the dry crushing plant and improved feeding of the crusher by the mining department had appreciably increased the production rate per operating hour in that plant. Therefore, it was decided to take advantage of the added crusher capacity to produce a finer rod mill feed and in that way increase grinding capacity. At approximately the same time, finer screens were installed in the rod mill circuits to give finer grind and thus improve liberation of the magnetite and ilmenite from the gangue and from one another. Prior to the first part of 1948, a 3/4-in. limiting screen was used for sizing rod mill feed. The first reduction in crushing plant screen size was to 1/2 in. With this screen, the circulating load in the tertiary crushing circuit was too high and plant capacity dropped below a practical hourly rate. A 9/16-in.-sq opening screen, installed next, proved satisfac-

Jan 1, 1951

By J. F. Myers, F. M. Lewis

The purpose of the mill tests reported herein, was to determine the relative power efficiency of fast and slow rod mill speeds on the ores of the Tennessee Copper Co. The tests were carried out at the Isabella Mill of the Tennessee Copper Co. under normal operating conditions. Every effort was made to keep the ore supply and other conditions constant, but it will be noted that some slight variation did occur. The open circuit 6 by 9 rod mill, and ore, used in these tests have been previously described.' Four motor drive pinions were available and the tests were performed in the following manner: each pinion was used to drive the mill for a period of one week. Constant sampling prevailed during the test run, and a composite sample for each speed test was made. Realizing that some slight liner wear took place during the four-week test-run, and that some slight variation of the ore may have taken place, a second and then a third series of four-week test-runs were made with the four different pinions. The screen analysis of each of the three-week run samples at the various speeds were composited and the results are shown in Table 2. The authors feel that the 22 weeks of operation consumed during these test-runs would represent fairly the effect of each mil1 speed. The data of line 37 show that within the error of sampling and plant operation, the tons of minus 65-mesh material generated per horsepower hour was the same at all four speeds. Obviously, rod and liner consumption could not be determined for each mill speed in so short a time. The rod load was maintained at a uniform level throughout the series of tests. The authors have operated rod mills at various speeds over the past several years, and it is their observation that rod consumption is directly proportional to the mill speed. Likewise, that the rod consumption per unit of work performed is a constant, providing that all other operating factors remain the same. It is a well known fact that the efficiency increases in a ball mill as the speed decreases. This is due to lateral segregation of the large and

Jan 1, 1950

By J. F. Myers, F. M. Lewis

C. G. McLACHLAN*-I have read this paper with considerable interest and wish to congratulate the authors on the care with which they carried out their experiments and for the detailed sizing data they have presented. 011 the other hand I do not feel that these data establish their contention that "with other factors the same, the work accomplished in a fine crushing rod mill is directly proportional to the rotating speed." My reason for making this statement is that their conclusion is based on the percentage of minus 65 mesh material produced at each of the speeds at which their tests were run. The rod mill is, however, not a fine grinding machine and therefore figures based on minus 65 mesh production are figures outside the range at which it operates to best advantage. Further, if rod mill performance is to be judged on the production of such material it should have been established that a rod mill will produce it as effectively as a ball mill. To check this last point I have gone over some of the rod and ball mill grind-ing figures for our Waite-Atnulet operation and find that the ball mill at that property produces more minus 65 mesh material per horsepower than the rod mill. Moreover, this comparison is even more favorable to the ball mill if it is limited to minus 100 mesh production. It therefore seems to me that the most satisfactory basis on which to try to com-pare the performance of the rod mill in the present case is by taking a weighted average of all the new surface produced per horsepower. W. H. Coghill3 has published data which can be applied to the sizing figures presented by the authors, and if this is done the units of new surface per horsepower produced in the Tennessee tests are as follows: Admittedly the increment of increase in new surface per horsepower shown in the foregoing figures is not great, but its trend is nevertheless definitely in favor of slower speed operation, for the conditions under which these particular tests were run. I also feel that some information regarding liner contour should have been given as I think it will be found that a mill which is equipped with liners which lift the rod load can be run at a slower speed than a mill in which the liners are comparatively smooth. J. F. MYERS and F. M. LEWIS (authors' reply)—The position taken by Mr. McLachlan is to be respected even though we are all aware of the faults of surface considerations. As he points out. the increment of increase is very small. It is so small in fact that for all practical purposes it does not conflict with the conclusions of the paper. The authors appreciate Mr. McLachlan's comprehensive study of the data.

Jan 1, 1950

By S. R. B. Cooke, H. S. Choi, I. Iwasaki

Oleic acid is the chief ingredient of fatty acids used as collectors in nonsulfide flotation. With a few notable exceptions, the various quantities of saturated and other unsaturated acids comprising the remainder are usually unspecified. There have been occasional investigations to determine the collecting ability of these other acids and their effect on collection with oleic acid, but much remains to be done in this field. Hukki and Vartiainen, on the basis of tests using palmitic, oleic, and linoleic acids and an impure linolenic acid, concluded: "The collecting power of fatty acids used in flotation increases with increasing unsaturation of the hydrocarbon chain." ' Their work was concerned mainly with the response of ilmenite to the foregoing collectors, although tests were also made with magnetite, pyrite, hematite, and rutile. Cooke and Nummela, employing an almost identical technical procedure to evaluate flotation of hematite, magnetite, and goethite with various fatty acids, including oleic, linoleic, and linolenic acids of the highest purity obtainable, found: "The effectiveness of 18-carbon unsaturated fatty acids, as collectors for hematite, decreases with increase in the number of non-conjugated double bonds." 2 Vn the foregoing investigations, collector efficacy was measured on the basis of reagent addition in moles per liter. Sources of fatty acids which may be used as collectors are legion, but provided the oleic acid content is high enough, cost is normally the determining factor. Usually this restricts severely the purity of the collector in terms of its oleic acid content. Within the past year or so users of crude oleic acid have become somewhat more discriminating, apparently realizing that some of the organic acid impurities may exert deleterious effects upon certain separations. Marine fish oils have been used as collecting agents, particularly in the earlier days of froth flotation. Currently their use is restricted in this field to relatively minor applications, although they are cheap sources of fatty acids. In an effort to increase the range of uses for fish oils, the U. S. Fish and Wildlife Service has awarded contracts to study these materials as sources of new products suitable for commercial development. Funds for these investigations were provided by the Saltonstall-Ken-nedy Act of 1954. One such contract was awarded to the University of Minnesota School of Mines and Metallurgy for the purpose of investigating the use of fish oil fatty acids and their derivatives in ore flotation. Besides the esters of various saturated aliphatic acids and of palmitoleic and oleic acids, fish oil also contains esters of monoethenoid and polyethenoid acids with 20, 22, and 2 carbon atoms. The basic purpose of the investigation was to determine whether the longer-chained unsaturated acids possess collective properties superior to those of the C,, monoethenoid oleic acid, the C16 monoethenoid palmitoleic acid, or the saturated C,, stearic acid and its shorter chain homologues; whether highly unsaturated acids have merit as collectors; whether rela-

Jan 1, 1960

By M. Takeda, H. Majima

Pyrite has been subjected to xanthate adsorption experiments in order to determine the nature of adsorption. The identification of adsorbed species by means of IR spectroscopy, as well as UV, shows that the dixanthogen adsorption is undoubtedly predominant on pyrite surface. The rest potential measured in a xanthate solution coincides with the redox potential of the xanthate-dixanthogen couple. Considering all the factors together, the adsorption mechanism of dixanthogen on pyrite has been proposed as This mechanism is consistent with the "passive" character of pyrite. From the measurement of the redox potential of the xanthate-dixanthogen couple in the homologous series, a rule similar to that for surface tensions proposed by Traube is also applicable. The polarization experiments were conducted on pyrite in a solution containing xanthate. In the anodic polarization, xanthate is observed to oxidize to dix- anthogen, which depresses oxygen evolution on py rite at higher potential levels. In spite of the importance of the presence of pyrite in the flotation of sulfide minerals, not many studies have been made on the xanthate-pyrite system in the absence of an activator or a depressant. In an early study by Gaudin and Wilkinson,' it was pointed out that no ferric xanthate was formed on a pyrite surface, while in another study Gaudin and his collaborators2 proved the formation of a very small amount of ferric xanthate. Afterwards, Gaudin et al.3 studied the pyrite-xanthate system with a radiometric technique and found indications of the presence of adsorbed dixanthogen on pyrite surfaces. Mamiya4 studied the flotation behavior of the pyrite-xanthate system and also suggested the possibility of dixanthogen. Recently, Fuerstenau and his coworkers at The Colorado School of Mines5 studied the role of dixanthogen in the xanthate flotation of pyrite and discussed the problem in terms of such properties as oxidation potential, zeta potential, flotation recovery, pH of solution, etc. However, the mechanism of dixanthogen adsorption at the pyrite-water interface is not yet understood. This paper is concerned with an electrochemical in-vestigation through which the mechanism of dixanthogen adsorption on pyrite is interpreted. EXPERIMENTAL MATERIALS AND TECHNIQUES Pure potassium xanthates were synthesized by an

Jan 1, 1969

By J. M. W. Mackenzie

Recent successful applications of emulsion flotation suggested that a detailed study of some of the physicochemical aspects of the process was warranted. The objective of the current research was to provide general information on the electrokinetic properties of emulsion drops of the type commonly used in oxide mineral flotation. Combinations of the parafin oil Nujol and several long-chain reagents in water were studied with respect to the effect of pH on the surface and zeta potentials. It war concluded that for emulsion drops in the presence of a long-chain reagent but in the absence of any other electrolyte which is adsorbed at the oil-water interface, the surface potential will be some two to four times the value of the zeta potential. During the last decade there has been a revival of interest in the so-called agglomeration, or emulsion flotation (in this paper the term emulsion flotation will be used), process. In this flotation technique, a neutral hydrocarbon oil, together with longcnain reagents, usually of a polar-nonpolar structure, are added to the pulp to function as collectors for specific minerals. The combination of oil and longchain reagent is either emulsified prior to addition to the pulp, or in the pulp itself, and the resulting collector species is an oil-in-water emulsion of a neutral hydrocarbon oil emulsified by polar-nonpolar long-chain reagents. Emulsion flotation has been used successfully in the treatment of ores containing iron, manganese,' and titanium oxides. 2 Two other major and long established applications of emulsion flotation are the flotation of coal and Florida phosphate ores. In recent years, emulsion flotation has been particularly successful in the treatment of ores containing oxide minerals which slime readily and, consequently, are difficult to treat by conventional flotation processes. The recent successful

Jan 1, 1970

By W. Mitchell, B. H. Bergstorm, C. L. Sollenberger

A unique compression testing machine was constructed to load individual 1/8 to I-in. spheres of glass, etc., at rates from 100 to 100,000 lb per min. During loading the applied load was continuously plotted us the deformation of the sphere-platen system. The load-deformation curve conforms to the theory of elasticity. The spheres were surrounded by steel retaining rings or by gelatin (to prevent secondary fracture). The product size modulus was determined from screen analyses. The data shows: 1) Energy input per unit mass is inversely proportional to the product size modulus (or directly proportional to the surface area per unit mass). 2) Increased loading rates slightly increase the energy input per unit mass required for fracture without affecting the preceding relationship. Theory and experiments show that much of the input strain energy is transformed into kinetic energy of fragments at fracture, this being a reason efficiencies based on "surface energies" are exceedingly small. This large kinetic energy component is usually dissipated as heat but may be partially reclaimed because impact of fragments against the surface of steel retaining rings causes additional comminution. There are currently several theories of crushing, all of which can be derived from the general energy equation of Gillilandl as was pointed out by Mitchellet al in 1954'and more recently by Rose and Sullivan. If the exponent of the equation dE-x-"dx is assigned values of 2,1, or 3/2, one obtains by intergration between suitable limits, the equations of Rittinger, kick,' and Bond,' respectively. Other investigators prefer to let the exponent be a variable parameter. To help resolve the controversy, the Allis-Chal-mers Research Laboratories set up a series of carefully controlled experiments in which the level of energy input required to induce the comminution of a single particle by slow compression loading was very accurately measured. The energy input requirement, in conjunction with the size analysis of the fragments produced at fracture, yielded an accurate energy-product size relationship for the conditions studied. APPARATUS The experimental apparatus was designed to apply a compressive load on opposite sides of an "ideal particle." Spherical shapes were chosen, because point contact loading is typical of the mechanics of conventional crushers. The bulk of the experimental data was obtained with glass spheres because glass is a fairly homogeneous, brittle material for which the properties follow definite statistical distributions. The spheres ranged from 1/8 to 1-in. diam. The compressive load was applied to the specimen at a uniform rate by a loading mechanism (Fig. 1) which acted through a system of levers. The uniform rates, ranging from 100 to 100,000 lb per min, were obtained by metering water into a bucket suspended at the end of the secondary level. Point contact was made with the sphere through tungsten-carbide platens. This latter material is extremely hard and has a high modulus of elasticity, thereby having a minimum of distortion when loaded. The actual load on the sphere was measured independently of the lever system by a load cell, Fig. 2, which was designed so that the voltage output of the load cell would be proportional to load. The deformation of the specimen was indirectly measured by a pair of transformers which were attached to opposite edges of the upper platen. The cores of the transformers, which were attached to the lower platen, moved relative to the transformer so that the voltage output was proportional to the deformation of the sphere-platen system. The load was plotted against the deformation on an X-Y recorder. The area under the curve, as shown on Fig. 3, was proportional to the energy input of the

Jan 1, 1961

By R. Schuhmann

Distribution of material in the fine sizes of a comminution product generally is well represented by the empirical equation' y = 100 (x/k)a [1] in which y — cumulative percent finer, x = particle size, a -= distribution modulus, and k = size modulus. Charles3 found that the energy consumption in comminution is usefully expressed by another empirical relation, E = Ak(1-D) [2] in which E = energy input per unit volume of material, A = a constant, k = size modulus based on Eq. 1, and n = a constant; (1-n) is the slope of a plot of log E vs log k. Holmes3 has presented energy equations similar to Eq. 2. The constants a and n in Eqs. 1 and 2 have been shown to depend both on the nature of the material and on the comminuting device. Moreover, Charles showed that within experimental error a and n are a — n+1 = 0 [3] Combining Eqs. 2 and 3, E = A k-a [4] In the first sections of this article it is shown that the energy equation, Eq. 4, can be derived directly from the size distribution equation for the fine sizes, Eq. 1. The derivations are made without assuming any of the specific relationships between energy and particle size which have been common in previous literature. For comminution processes in which Eqs. 1 and 4 adequately represent the experimental data, the constant A in Eq. 4 is found to be a simple and useful inverse measure of grindability. That is, A is the energy consumption per unit volume of comminution product finer than unit size as determined from the straight line portion of the log-log plot of the size distribution. These considerations all lead to a unifying hypothesis of comminution mechanism from which both Eq. 1 and Eq. 4 can be derived. Finally, it is pointed out that this hypothesis raises serious questions as to the significance of the Rittinger hypothesis, the Kick hypothesis, and other theories in which energy numbers are systematically assigned to various size fractions of comminution products in order to calculate theoretical energy consumptions. Derivation of the Energy Equation from the Size Distribution Equation: For simplicity, consider the comminution of 100 volumes of a feed material of relatively uniform particle size. The comminution process may be considered as the summation of many individual and independent comminution events. The extent of comminution is most easily expressed as the number of comminution events, z. In the first derivation, the key assumption is that the characteristics of the comminution events in a given crushing or grinding process are substantially constant and do not vary with the progress of the comminution process. Accordingly the characteristics of an average comminution event may be defined. In one such event, a quantity of energy $E is applied to a single particle of size f and volume $v. The crushing of this particle produces fine particles with a size distribution similar to that given by Eq. 1: yw=100(x/ka)a0 [51 In this equation yo, a0, and k0 are used to characterize the product of an individual comminution event rather than the product of the comminution process as a whole. In using Eq. 5, we will not be concerned with values of x close to the feed size f and will therefore assume only that the equation is applicable to the finest sizes of the material. In 100 volumes of total product, the actual volume of product finer than x from a single comminution event, or dy, is given by The total volume of material below size x, resulting from z events, is then given by y = z(dy) =z(dv) (x/ka)a0 =" Eq. 7 reduces to Eq. 1 when we let a, = a and [8a] z =100/dv (ka/k )1 or k = ka (zdv/100)-1/a [8b] Eq. 8a shows that the distribution modulus of the comminution product is the same as for the product of an individual comminution event. Eq. 8b shows how the size modulus of the comminution product k varies with the extent of comminution as measured by the number of events, z, or as measured by the fraction of the feed actually subjected to com- minution1 zdv/100. The energy input to 100 volumes of total feed, or 100E, is the sum of the energy inputs for all the comminution events: 100E =z (dE) [9]

Jan 1, 1961

By I. C. Edwards, G. E. Agar

INTRODUCTION Many research efforts over the past years have been devoted to the study of energy consumption in comminution and the characteristics of the broken material. The old "laws" have been superseded by more general methods of analysis1,2,3 but these methods have not received much attention outside the laboratory. The work to be described here was done in order to obtain scale-up information on wet rod milling of sylvinite. EXPERIMENTAL A 30 x 51 in. Denver rod mill with a scoop feeder was used for these tests. Ore was fed from a variable speed screw conveyor into the feed box along with saturated brine. The mill was filled to approximately 45% of its volume with 2400 lbs of a mixed rod charge. The minimum possible feed rate was 2.5 tph and the practical maximum for this mill was 8 tph. Individual tests were run by setting the solid feed rate, then adjusting the brine flow rate to give the desired pulp density. After steady state, as evidenced by constant discharge pulp density, had been reached, samples of the discharge were taken at 15-minute intervals. These samples were filtered, washed with alcohol, dried, then screened on Tyler screens using a Ro-tap shaker. The sylvinite feed was regular plant feed that had been scalped at 20 mesh and was tapped from the coarse ore bins. It had been previously passed through a roll crusher set at 3 inches and after scalping was essentially minus 1 in. plus 20 mesh. RESULTS The screen analysis of samples from each series of tests was plotted on double logarithmic scale paper to determine the reliability of the series. In some cases, a faulty sample or screening procedure dictated that the results of one test be discarded. The criterion is a simple one — if the slope of one plot was noticeably different from the others in the series, it was discarded. The only cases that caused difficulty were those in which the brine was not thoroughly displaced from the solids. When this occurred agglomerates were easily identified on the screens and the whole of the sample was retained on 3 or 4 screens. There were no border line cases. The number N given in Table 1 is the number of size analyses that were pooled to form the data shown in Fig. 1. While examining the reliability of the sizing and sampling by plotting the data, it became apparent that there was no significant difference between grinds made at 50 and 60% solids. For the analysis given here, these tests were regarded

Jan 1, 1967

By P. L. De Bruyn, R. J. Charles

THE transfer of kinetic energy of translation into other forms of energy by impact is a fundamental process in most crushing and grinding operations. During and after the impact process the original source energy may be accounted for in any of the following possible forms: 1) Kinetic energy of translation of both the impacted and impacting objects. 2) Kinetic energy of vibration of the components of the impact system. 3) Potential energy as strain energy of the components of the system or in the form of residual stresses. 4) Heat generated by internal friction during plastic deformation or during damping of elastic waves. 5) New surface energy of fractured materials. At any instant during the impact process only the strain energy of the components of the system can contribute directly to the brittle fracture process. If fracture is the desired result, as in comminution, it would seem advantageous to choose or arrange the conditions of impact so that a maximum amount of the original kinetic energy could be converted to strain energy at some moment during a single impact. The present work deals with determination of these desirable conditions for a simple case of impact and application of the principles involved to general cases of impact. Experimental Method: Longitudinal impact of a rod with a fixed end was chosen as the impact system for investigation. The rod was mounted horizontally and the fixed end was formed by butting one end of the rod against a rigidly mounted steel anvil. The rod, of pyrex glass, was 10 in. long by 1 in. diam with both ends rounded to a 6 in. radius. The rounded ends permitted reproducible impacts on the free end of the rod and assured a symmetrical fixed end. Pyrex was selected as the rod material because of the marked elastic properties of such glass and the similarity of fracture between pyrex and many materials encountered in crushing and grinding operations. The frequency of natural longitudinal oscillation of the rod was 10 kc, and thus simple electronic equipment could be used for observation of strain changes occurring in the rod at this frequency. As shown in Fig. 1, impacts on the free end of the rod were obtained either by a pendulum device or by a spring-loaded gun. Relatively heavy hammers (100 to 600 g) of mild steel were used in the pendu- lum impacts, while fairly light projectiles (20 to 80 g) were fired from the spring-loaded gun. One of the main objects of the experimental work was to obtain the strain-time history of the rod as a function of the mass and kinetic energy of the impacting hammers. For this purpose a technique involving wire resistance strain gages and a recording oscilloscope was employed. Five gages were applied at equidistant sections along the rod, and by means of a switching arrangement the strain-time history at any section, and for any impact, could be obtained in the form of an oscillograph with a time base. The equation relating strain and voltage change across a strain gage through which a constant current is flowing is as follows: e = ?v/iRF [1] ? = strain, ?v = voltage change, i = gage current, R = gage resistance, and F = gage factor (from manufacturer's data — SRA type, Baldwin Lima Corp.). With the above equation an oscillograph depicting voltage change vs time on a single trace can be converted directly to a strain-time diagram if a calibration of the vertical response on the oscilloscope screen for specific voltage inputs is available. In the present case the calibration was obtained by photographing precisely known audio frequency voltages on the same oscillograph as that on which a voltage-time trace from a strain gage had been made. Synchronization of the beginning of the single trace with the beginning of the impact was accomplished by permitting contact of the impacting objects to close an electrical circuit from which a voltage pulse, sufficient to initiate the trace, was obtained. The struck end of the rod was lightly silvered for purposes of electrical conduction so that it would form one of the electrical contacts. Markers every 100 micro-seconds on the traces served for a time base calibration. Determinations of the kinetic energies of translation prior to impact were made in the case of the pendulum hammers by measuring the height of fall of the hammer and in the case of the projectiles by measuring the exit velocity from the gun barrel by means of an electrical circuit employing light sources, slits, and phototubes.' During the experimental work it became evident that the time of contact between the impacting object and the rod was an important variable in the impact process. Measurements of the times of contact were made, therefore, for every impact for which a strain-time record was obtained. The time of contact was determined by permitting the impacting components, when in contact, to act as a closed switch and discharge a condenser at relatively constant voltage. The discharge was observed and photographed with a time base on the oscilloscope screen.

Jan 1, 1957

By J. P. Zannaras

Referring to the article by R. J. Charles and P. L. de Bruyn, let us assume that W = weight of glass bar; P = weight of hammer; e = total deformation; K = unit of deformation; K = potential stress energy; E = modulus of elasticity; L = length of the bar; 7 = coefficient of inertia; h = height, ft; V = velocity, fps; and a = cross section area. The portion of kinetic energy which is effective in producing stress energy in a fixed bar struck horizontally is given by the formula" 1 + 1/3 W/P K =1+1/3w/p/(1+1/2w/p)2 P.V2/2g = Ph where 1 + 1/3 W/P ? (1 + 3W/P/(1=1/2w/p)2 [8] Putting e e = W/P =------------ From the above equation it can be seen that the maximum transfer of kinetic energy to stress energy is when e = 0 or W/P = 0 which indicates that the weight of the hammer must be very large as compared with the weight of the impacted rod. Eq. 8 diametrically opposes the conclusions reached by the authors of this article. In fact, if their suggestions were followed to the extreme when e = co when P = 0, there would be no transfer of kinetic energy to stress energy at all, as 7, becomes zero. Eq. 8 presumes that the velocity with which the stress is propagated through the bar is infinite, whereas the authors claim that the compression waves reflected are reaching the struck end of the bar prior to the complete transfer of the kinetic energy to cause such modification of the conditions there as to make them reach the reverse conclusions demonstrated by the above formula. That such interference exists is unquestionably demonstrated by the authors and others. However, if my observations are correct, such interference for this specific experiment and also for practical comminu- tion is insignificant, and the conclusions of the authors are in error and must be reversed to comply with Eq. 8. Eq. 5, w. = AE 2/2, given by the authors on page 51, is derived from the following equation (Eq. 9): K = 1/2Pe, where P = Sa, S = ?E, e = EL, and L = 1. The above formula, Eq. 9, cannot be applied in this case. This formula is applicable for static loads where the load increases from zero up to its final value, P, in such a way that the deformation at different instants is proportional to the loads acting at those instants and actually represents the area of a right triangle in the strain load diagram of base e and height P. The typical photographs shown in Figs. 3 and 4 represent the familiar strain load diagrams, and since the line of the wave marks the existence and intensity of the strain with the unquestionable conclusion that such strain has been caused by the action of a load acting continuously all along the wave until it reached the horizontal axis, the work stored at this point is represented by the area under the wave line and the horizontal axis and not by the area of the fictitious triangle given by the authors. Then if this is correct, even visual estimation of these areas at gage stations given in the typical photographs of Figs. 3 and 4 suffice to contradict the authors' calculation given in Figs. 6a and 6b and Figs. 7a and 7b. The typical photographs presented by Charles and de Bruyn show a considerable variation of the intensity of the strain at different stations but very small variation of areas which actually represent the stress energy at the corresponding stations. And, apparently, by squaring the small quantities, the authors magnified their error tenfold. J. M. Frankland's paperV iscusses the relative strain intensity and not the total energy for different types of impact loading. He states in his paper, "The reader is explicitly warned not to confuse the results in this report with those obtained when the load is applied by a blow as from a hammer. In this case the peak load rises to very large but mostly unknown values. The accompanying large deflections and stresses are the result of high values of P, not of the dynamic load factor n. According to Frankland "the dynamic load factor" is the numerical maximum of the response factor. It therefore appears that the authors followed the same procedure in obtaining the relative strain energy ab-

Jan 1, 1957