Search Documents

By Paul A. Farrar, Louis P. Stone, Harold Margolin

The Ti-Mo-0 system was investigated in the region 0 to 45 wt pet Mo and 0 to 10 wt pet 0, from 600° to 1400°C. Solidus data are also presented. Isothermal sections at 700°, 900°, 1100°, and 1300°C, and vertical sections at 1 and 28 wt pet Mo, and 1 and 10 wt pet 0 are included. STUDY of the Ti-Mo-0 system has been carried out as part of a general study of titanium phase diagrams. The binary Ti-Mo system has been investigated in whole or in part by several investigators.1-8 It was found that molybdenum and ß-tita-nium form a complete series of solid solutions and that the ß/a + ß transus is depressed to below 600°C at approximately 30 pet Mo.* The Ti-O system has been investigated partially or fully in the range 0 to 30 pet 0 by several investigators." Extensive solubility of oxygen occurs in the field. While a is

Jan 1, 1957

By R. F. Dickerson, D. A. Vaughan, A. F. Gerds

ALTHOUGH the metallurgy of uranium has been under intensive study since the early 1940's, no systematic effort has been made to identify the non-metallic inclusions in uranium. Uranium carbide (UC), which is probably the most common inclusion found in graphite-melted metal, has been tentatively identified by previous investigators, but the other nonmetallic inclusions have received little attention. Since metallography is a valuable tool in metallurgical studies, the metallographic identification of the nonmetallic inclusions in uranium is important. Such an investigation has been completed and the identification of slag-type inclusions and of uranium monocarbide, uranium hydride, uranium dioxide, uranium monoxide, and uranium mononitride is described. Metallographic Preporation It is often possible to prepare specimens for metal-lographic examination equally well by several methods. The specimens which were examined in this work were prepared by one of two acceptable methods. For the convenience of the reader, both methods will be discussed in detail and will be referred to simply as Method I or Method II in the subsequent sections. For both Methods I and 11, specimens for microscopic examination usually were mounted either in bakelite or in Paraplex room temperature mounting plastic. Method I—Specimens were ground in a spray of water on a revolving disk covered successively with 120-, 240-, and 600-grit silicon carbide papers. It was necessary to perform the final grinding operation carefully on worn 600-grit paper to keep the scratches as fine as possible. After washing and drying, the specimens were polished for 3 to 4 min on a slow speed wheel (250 rpm) covered with a medium nap cloth. Diamet Hyprez Blue diamond polishing paste, Grade 00, 0 to 2 µ, was used as abrasive with kerosene as lubricant on the wheel. Specimens were washed thoroughly in alcohol and final polished electrolytically in an electrolyte composed of 1 part stock solution (118 g CrO, dissolved in 100 cm3 H2O) with 4 parts of glacial acetic acid. A stainless steel cathode was used. At an open circuit potential of 40 v dc, a polishing time of 2 sec retained inclusions well with the bath at room temperature. If additional etching was required to sharpen the interface between the metal and the inclusions, an electrolyte composed of 1 part stock solution (100 g CrO3 and 100 cm8 H20) and 18 parts glacial acetic acid was used at room temperature. Best results were obtained by etching for from 10 to 15 sec at 20 v dc in the open circuit. Surfaces obtained by this method are suitable for microscopic examination. However, if desired, they may be etched further with other chemicals. Method 11—Rough grinding was done on a wet 180- or 240-grit continuous grinding belt. The specimen was then ground by hand successively on 240-, 400-, and 600-grit silicon carbide papers in a stream of water. Final polishing was accomplished on a 4 in. high speed wheel (3400 rpm) covered with Forstmann's cloth. Linde B levigated alumina, suspended in a 1 volume pet chromic acid solution, was the abrasive. Specimens usually were polished in 5 min or less by this technique. Often the inclusions present in the metal were identified in the mechanically polished condition. When etching was required to outline inclusions more sharply, one of the two following methods was used. In the first method, the specimen is etched lightly while electropolishing in the chromic-acetic acid solution described above (1 part of stock solution to 4 parts of acetic acid). The electrolyte was refrigerated in a dry ice-ethyl alcohol bath and specimens were etched at 60 v dc on the open circuit for 2 or 3 cycles of 3 to 4 sec each. The second technique utilizes electrolytical etching at about 10 v dc (open circuit) in a 10 pet citric acid solution at room temperature. X-Ray Diffraction Technique The major problem in the identification of inclusions in metals by X-ray diffraction techniques is the extraction of a sufficient amount of each type of inclusion to obtain an X-ray diffraction pattern. In the present study, X-ray diffraction patterns were obtained from individual inclusions of the order of 10 µ diam. The polished and etched samples shown in the micrographs were examined at a magnification of X54 or XI00 with a binocular microscope. This allowed sufficient working distance to extract the inclusions with a needle probe for powder X-ray diffraction analysis. Friable inclusions such as MgF2, CaF2, UO2, and UH3 could be freed from the metal by probing the as-polished and etched surface. The fine particles then were picked up on the end of a Vistanex-coated glass rod (0.002 in. diam) which was held in a brass adapter made to fit the powder X-ray diffraction camera. The end of the glass rod was centered in the path of the X-ray beam. In the case of the UC, UO, and UN inclusions which are smaller in size, more metallic in appearance, and less friable than the other inclusions, it was necessary to etch the inclusion in relief before extraction. UN inclusions etched sufficiently in relief in the electrolytic polishing solution described in Methods I and II by increasing the polishing time. UN inclusions were relief etched by extending the

Jan 1, 1957

By J. R. Kyte, L. A. Rapoport, R. J. Stanclift, S. C. Stephan

Experimental studies covering a wide range of core materials and fluid properties have been conducted to determine the mechanism of oil displacement by water in a partially gas-saturated porous medium. In all instances, the presence of a gas phase was found to have a beneficial effect in reducing residual oil saturations. The practical significance of this benefit is discussed, and a simplified procedure is outlined for evaluating the effects of free gas on water flooding by means of short core tests. INTRODUCTION In addition to oil and water, reservoirs subjected to water flooding frequently contain, also, a gas phase. Common engineering procedures account for the presence of this "free gas" only from the viewpoint of volumetric balance, implying that the only role of the gas consists of providing "fill up" space. It is usually visualized that during the initial stages of the water invasion, the oil, moving ahead of the water, displaces part of the gas and that subsequently the remaining portion of the gas phase is totally compressed and dissolved in the advancing oil bank. Thus, consideration of a two-phase, water-oil flooding mechanism supplies an adequate basis for predictions of oil recovery if the pressure build-up caused by the flood is sufficiently great, so as to reduce the free gas saturation to a negligible value in any portion of the reservoir by the time that portion is reached by the advancing flood water. In many in- stances, however, waterflooding operations are carried out when the reservoir pressure is still relatively high SO that the pressure build-up associated with the water flood may not result in complete dissipation of the gas phase. Under such circumstances it is necessary to ascertain whether or not the presence of free gas has an effect on waterflood behavior and, if so, to account for any such effect in the evaluation of field operations. The difficulties encountered in attempting to arrive at a comprehensive picture of the displacement mechanism of oil by water in the presence of free gas stem from the fact that most of the published data on this subject were obtained under conditions that were either not clearly representative of those existing in a reservoir or not sufficiently controlled to permit evaluation of the effects specifically caused by the gas phase. Some of the most precise data found in the literature were obtained in tests using a "static" gas phase created prior to each water flood by circulating oil through partly gas-saturated cores until a "trapped," residual gas saturation was established throughout the system.' Other investigations were conducted under more representative conditions where the gas phase was free to move during the water flood: but in most cases the results of these tests were obscured by auxiliary phenomena which arise from the compressibility and solubility of the gas and preclude quantitative conclusions.2,3,4 Prior to water flooding, a reservoir usually contains oil and gas, distributed in a manner in which both are free to move. Thus, the principal objective of the present studies was to determine the type of displacement mechanism occurring when water invades a porous medium containing oil and a "mobile" gas phase. Further-

Jan 1, 1957

By W. A. White

UNDERCLAY squeeze is the plastic flowing of underclay below coal pillars into mined-out entries and rooms. Squeezes may be caused either by wet mine conditions where the moisture is taken up by the clay—making it more plastic—or by the presence of certain clay minerals, such as mont-morillonite, which are plastic when there is enough natural moisture. Under either condition, sufficient stress will cause the underclay to flow. Squeezes may fill an entry or room within several hours, or it may be several months before movement stops. Squeeze areas commonly cover hundreds or thousands of square yards. The Coal Div. of the Illinois State Geological Survey has collected samples of underclays from various mines and from cores drilled by coal companies in the state. From these samples natural moisture content, particle size and particle size distribution, and clay mineralogy are determined. Data from samples collected from the underclay below Herrin (No. 6) coal in the Lumaghi Coal Co. mine near Collinsville, Ill., are used in this report to clarify points in the discussion. Data from samples taken from other mines lead to the same conclusions. A generalized geological section for the area is given in Table I. The underclay below coal No. 6 ranges from a few inches to 3 or 4 ft thick. The upper 6 to 18 in. are noncalcareous; the lower part becomes more calcareous with depth. Limestone nodules become larger with depth, almost grading into the limestone below. In areas where the clay is nearly absent the limestone may thicken to take its place; thus they may complement each other in thickness. There are two types of squeeze areas in a mine. In one type up to 3 or 4 ft of underclay lie in what appears to be a depression in the limestone underneath. This is suggested by a rim surrounding the squeeze area where the underclay is thin and the limestone lies within a few inches of the coal. In the second type the underclay of the squeeze area is surrounded by underclay of similar thicknesses which does not squeeze. Test Methods: Natural moisture content, particle size and particle size distribution, and clay mineralogy were determined by the following methods: Natural moisture is the moisture content a clay contains in its natural environment, expressed in percentage of the weight of ovendried clay (110°C or 230°F). To obtain the natural moisture content, given in Table 11, the clay samples were sealed in containers as soon as the samples were taken in the mines. Particle size and particle size distribution were determined by the pipette method,' and the data were plotted as cumulative curves, Fig. 1, on semi-logarithmic paper. Particle size was plotted on the logarithmic scale and percentage on the arithmetic scale. The quartiles (diameters that correspond to frequencies of 25 and 75 pct) and medians (diameters that correspond to the frequency of 50 pct) of the samples were determined from these curves. The clay minerals were identified from the data obtained by differential thermal' and X-ray powder" techniques. The differential thermal analyses were made on the whole samples, whereas the X-ray analyses were made on fractions of less than 2p. Data and Discussion Moisture Content: After the sealed jars had stood for 24 hr, those that contained squeeze samples had perspired, so that droplets of water had accumulated on the insides of the jars. Table II shows the moisture in the clay after it had perspired for 24 hr. (This perspiring was not noted in samples from nonsqueeze areas.) After perspiration one of the squeeze samples still had a higher moisture content than the samples that did not squeeze. Clay Mineralogy: The thermal analysis, Figs. 2 and 3, indicates that the clay minerals are chiefly micaceous in type; the low-temperature endothermal

Jan 1, 1957

REJUVENATED is an apt word to apply to Chino, Kennecott's big open-pit mine at Santa Rita, New Mexico. Back in 1923 Chino was merged with Ray by an exchange of shares, and in 1926 the Ray-Chino combination was taken over by Nevada Consolidated through an issue of bonds that were traded for the Ray and Chino assets. Subsequently, of course, the whole package was acquired by the Kennecott Copper Corporation. On the basis of the terms of the Ray-Chino-Nevada exchanges, Chino was rated third in value, something less than thirty per cent of the total. In 1955 the appraisal would doubtless be forty per cent or more. But it is not only vis-a-vis Ray and Nevada that Chino has blossomed out. At the end of 1931, Chino ranked seventh among the Porphyries in point of output; whereas by the end of 1954 it was fifth,. having passed both Inspiration and Nevada Consolidated. Sharp curtailment in production in 1932-33-34 and total suspension in the two years following (see Fig. 21) found the property in a somewhat parlous position. However, the engineers had not been idle; they had been planning for the future, and in 1937 a far-reaching program of rejuvenation was launched. During the ensuing five years, capital expenditures totaled more than $8,500,000. Among the projects undertaken were the following: (1) Mine-Purchase of larger and better equipment for drilling, loading, and transporting the ore. (2) Mine-Beginning of the first systematic project to leach and recover copper in the waste dumps at the mine.

Jan 1, 1957

By H. R. Brannon, J. S. Osoba

The introduction of the scintillation counter into field use for gamma-ray well logging has provided a new tool with special utility for the deternzination of natural radioactivity of sediments. Previous subsurface gamma-ray measurements have indicated only the total amount of radioactivity of the sediments. With the scintillation counter, the relative amounts of the elements which emit gamma radiation can be determined. Sediments logged included 35 zones in wells located in the Teras Gulf Coast, East Texas, and West Teras. Although the data obtained from measurements made to date are not sufficient to evaluate the possibilities of spectral logging, it appears likely that spectral measurements will yield information of geologic value. INTRODUCTION Although variations in the natural radioactivity of sediments were recognized as early as 1909,1 the appli- cation of such variations to borehole logging was not made until almost 30 years later. A group of Russian workers in the early 1930's were successful in making crude measurements of natural gamma activity in an oil well borehole. The first practical gamma-ray logging system was developed by Howell and Frosch2 in 1939. Induced radioactivity, or neutron, logging appeared soon after the introduction of gamma-ray logging. After early work had demonstrated the potentialities of radioactivity logging, development of sensitive and stable logging equipment for field use followed, so that neutron and natural gamma logs are now run routinely and have proved to be extremely valuable in characterizing subsurface formations. Even though tremendous strides have been made in developing radioactivity logging, it is apparent that the ultimate in the method of logging has not been reached, for, until very recently1 in none of the commercially available logging systems has advantage been taken of the fact that gamma radiation is composed of a spectrum of rays, each ray having a distinct and characteristic energy. An individual gamma ray originates in a single element and has energy determined by the element. The inten- sity of radiation, or number of rays emitted from unit volume in unit time, is determined by the concentration of the element. If it were possible to sort out these gamma rays and assign them to their parent elements, thereby essentially analyzing for the elements, a wealth of new information descriptive of formation material and fluid content would be at hand. For example, if in natural gamma logging, the gammas due to potassium and to the thorium and uranium series were measured individually, data would thus be available on the concentrations of each of the three elements, adding materially to the information content of the log. In contrast, conventional gamma logs measure only a quantity proportional to the combined concentrations of uranium, thorium, and potassium. The naturally radioactive elements occur in sediments in concentrations dependent on source material of the sediment, and through their chemical characteristics, on conditions of deposition,' so that the individual concentrations may be diagnostic for particular formations. These concentrations, particularly if measured in situ, could lead to a powerful tool for correlation and for reflecting environmental conditions under which sedimentation took place. As a correlation tool, individual uranium, thorium, and potassium measurements

Jan 1, 1957

By S. C. Sun, D. R. Mitchell

T LTRASONICS can be used to deslime and up-grade ores, such as tungsten and tin, which slime excessively with high losses of value in the tailing and are difficult to deslime with conventional methods. Experimenta] work has been performed with a test-tube size ultrasonic classifier. Larger equip-

Jan 1, 1957

By Henry A. Wriedt, John Chipman

Equilibrium in the reaction of hydrogen gas with oxygen in liquid nickel, iron, and their alloys has been studied at temperatures of 1500° to 1700°C. The equilibrium con^stant, 0/p, [% O], is greater in nickel then in iron by a factor of 45 at 1594 C. In the alloy steel range, the activity coefficient of oxygen is slightly increased by the presence of nickel. NICKEL is more resistant to oxidation than is iron, in both the solid and the liquid state. The solubility of oxygen,' however, is greater in nickel than in iron. The two metals and their liquid alloys constitute an interesting series of solvents in which the chemical behavior of oxygen can be studied by methods similar to those used for liquid iron.' Experimental Method The furnace assembly, including the tube for preheating the entrant gas, was the same as that described by Gokcen and Chipman. " controlled mixture of water vapor, hydrogen, and argon preheated to approximately the melt temperature impinged upon the surface of the liquid metal. The charge, weighing about 35 g, was held in an alumina crucible at constant temperature in the gas stream for a prolonged period, then quenched in a stream of cold helium, sampled, and analyzed for oxygen by the vacuum fusion method. The temperature of the liquid metal was measured by a Leeds and Northrup optical pyrometer which had been checked against a similar instrument certified by the National Bureau of Standards. The freezing point of electrolytic iron in hydrogen, taken as 153j°C, was used for frequent checks. This point and the emissivity determined by Dastur and Gokcen" established the transmissivity of the optical system. The emissivities of Fe-Ni alloys at 1535" are known from the experiments of Smith and Chipman,h nd it was assumed that the variation with temperature is parallel with that of iron. Recorded temperatures are probably accurate within k5"C. Preparation of Gas Mixtures—Since the ratio H,O:H, had to be much higher for nickel than for iron, it was found convenient to construct two separate systems for gas preparation. In both cases, the ratio of argon to the sum of the other two gases was at least 4, the proportion of hydrogen and water vapor being varied to produce H,O:H, ratios from 0.2 to 70. The primary purpose of the argon was to diminish the errors caused by thermal separation' in the gas phase. In addition, its presence lowered the saturation temperature required for a given H,O:H, ratio and minimized the difficulty of preventing condensation. Both systems were modifications of the one used by Dastur and Chipman.' For H,O:HI ratios greater than 2, welding-grade argon purified by passage over magnesium chips at 620°C was mixed with hydrogen produced in the electrolytic cell shown in Fig. 1. The design was based on a cell used by Bodenstein and Pohl," the important features of which area nickel wire cathode and sodium hydroxide solution as the electrolyte. The rate of hydrogen evolution was controlled by a calibrated ammeter and a rheostat in the circuit, the current efficiency being taken as 100 pct. Precise control of the argon flow rate at about 300 ml per min was achieved by means of a capillary flowmeter having a controlled pressure drop. The molar flow rate was measured volumetrically before each run, and a constant flowmeter setting was maintained thereafter. The A-H, mixture passed through a water saturator of the type previously described," the saturation temperature being maintained automatically with a fluctuation of k0.04"C. The tube between saturator and furnace was heated by a resistance winding. The system was of all Pyrex construction with the exception of the stainless steel tube containing magnesium chips. This was connected with the glass tubing at the upstream end by

Jan 1, 1957

By F. R. Jones

AT Tahawus, N. Y., National Lead Co. operates the MacIntyre development. Here the world's largest titanium mine produces 5200 long tons of ore per day and pours 8000 long tons of waste rock over its dumps. Concentrated ilmenite is sent by rail to National Lead Co. pigment plants, and a second product, magnetite, is sold to steel producers in raw form or is agglomerated and shipped as sinter. Several earlier attempts had been made to produce iron from the deposits, which have been known since 1826. These attempts failed, chiefly because of titanium impurity. In 1941 the present owners reestablished the operation for production of war-scarce ilmenite, and the impurity became the main product. The Ore: The MacIntyre ore zone is about 2400 ft long and 800 ft wide in horizontal measurements. Ore outcrops were found on the northwest side of Sanford Hill, 450 ft above Sanford Lake and 2500 ft southeast. The zone dips at about 45" toward the lake and plunges to the southwest. The ore minerals, ilmenite and magnetite, are unevenly distributed in bands roughly parallel to the long axis of the ore zone and are interspersed with bands and horses of waste. Hanging wall ores are fine grained and grade from rich ore to waste rock or gabbro. Footwall ores are coarse grained and are almost entirely ilmenite and magnetite. The foot-wall waste rock, anorthosite, is the common country rock. Several faults cut the ore zone. These faults have no great displacement but do contribute to the great physical variations in ore rock and surrounding waste. The Mine: The MacIntyre mine is an open pit operation, with benches at 35-ft intervals. The lowest bench is now 54 ft below lake level. Loading equipment consists of three electric-powered shovels (a P & H model 1400 with 4-yd dipper and two Bucyrus-Erie models 85-B with 2%-yd dippers) and one diesel-powered shovel (a Northwest model 80D with 2%-yd dipper). Ore and waste are transported to a 48x60-in. jaw crusher in ten 22-ton Euclid trucks with 300-hp diesel engines. Ordinarily the two Bucyrus-Erie 2 % -yd shovels load ore into a fleet of three or four trucks. This combination works two 8-hr shifts per day, moving 5200 long tons of ore to the crusher and removing a small portion of the waste rock. The P & H model 1400 shovel, with a fleet of four trucks, loads waste on three shifts per day. The mine operates on a 5-day week, with a small maintenance crew working Saturday. Oversize rock is broken by a dropball handled by an Osgood model 825 rubber-mounted crane.' Ore and waste are broken by drilling and blasting 9-in. diam vertical holes behind the benches. Bucyrus-Erie 42-T churn drills are used to drill the holes, which are extended 4 ft below the bench level on which the broken rock will fall. Drilling and Blasting History: In its early years the mine was equipped with Bucyrus-Erie 29-T churn drills, which drilled 6-in. holes. To keep up with production requirements the hole diameter was soon increased to 9 in., and by 1950 the three 42-T drills now in use had been acquired. Early blasting experiments with different kinds and grades of explosive led to adoption of 90 pct straight gelatin dynamite as standard. It was recognized that this explosive was expensive, and from the start of operations until 1950 extensive experiments were made using blasting agents of the ammonium nitrate family. Results were recorded as uniformly poor, with great build-up of oversize rock. The expense of these experiments, and the discouraging results, caused the abandonment of any expectation of breaking MacIntyre rock with anything but 90 pct straight gelatin dynamite. Further standardization led to 9-in. well drillhole spacings set at 16 ft in ore and 18 ft in waste, exceptions being permitted only for unusual conditions. The hole burdens were theoretically about 22 ft. Due to the extreme back-slope of bench faces, caused by blasting with heavy charges of dynamite, actual burdens were commonly well over 30 ft. Lack of precise control resulted in many holes having a burden as light as 15 ft. General practice was to stem 6 or 7 ft of hole with magnetite concentrate, the amount of stemming being left to the discretion of the pit foreman. Usually all holes in a row were fired instantaneously with Primacord detonating fuse. Millisecond delays were

Jan 1, 1957

Jan 1, 1957

By Ulf S. Landergren

Diffusion coefficients and marker movements have been determined in brass using welded couples. Three different concentration ranges were employed at 750°C, while a fourth concentration range was measured at 500°, 600°, 700°, and 800°C. Marker displacements toward and porosity development in the high zinc side of the couple were observed in all cases. The results were interpreted as favoring a vacancy diffusion mechanism. IN the large amount of diffusion literature which has accumulated during the past half century, very few experimental data have been presented on body-centered-cubic metallic phases. The impressive combination of experimental and theoretical studies which has given the vacancy mechanism a fairly secure position as the preferred mechanism for most face-centered-cubic metals has no counterpart for body-centered-cubic phases, although the theoretical picture seems to be in a better state than the experimental work. The attempts to select diffusion mechanisms by the theoretical calculation of the activation energy for the various conceivable unit diffusion processes and the energy of formation of the type of lattice defect required have been based on models of two kinds. The first kind utilizes potential functions fitted for certain properties of pure crystalline copper; the second kind is fitted for sodium. The latter is an example of an open metal in which the metallic ion is small compared with interatomic distance,&apos; while the former is characteristic of the larger class of metals in which the ions have diameters about as large as the interatomic distance. brass should resemble copper in this fundamental property. It should be evident that results on the mechanism of diffusion obtained for one of these classes need not necessarily apply to the other. Huntington and Seitz, using a model of the copper type, showed that the activation energies to be expected for interstitial migration or a two-atom direct interchange were much higher than that for vacancy diffusion. Zener pointed out that a four-atom ring rotation would involve an activation energy considerably lower than the two unlikely mechanisms although still higher than the vacancy mechanism in the face-centered-cubic structure. Furthermore, he argued, the four-atom rotation would be relatively easier in a body-centered-cubic lattice and might be competitive with the vacancy mechanism. Paneth showed that a body-centered-cubic crystal-like sodium could form interstitial defects of special type, called a crowdion, by crowding an extra atom into < 111 > directions where the defects would affect a line of about eight atoms. The defect was constrained to move along the defining line. Unlike the face-centered-cubic case, therefore, the theoretical calculations for the body-centered-cubic mechanism do not provide a very clear-cut answer, and the absence of adequate experimental studies is the more serious. This investigation was undertaken for the purpose of obtaining useful information on diffusion in body-centered-cubic phases. brass was chosen for several reasons: 1—the phase field is sufficiently wide at high temperatures to permit the use of diffusion couples with adequate concentration ranges for satisfactory chemical analysis, 2-—thermodynamic activity data are available for the calculation of mobilities from diffusion coefficients, 3—the phase is as close to the theoretical model of the copper -type on which the calculations have been done as any body-centered-cubic metallic phase is likely to be. Measurements of the movements (if found) of inert markers during the diffusion process would indicate that a vacancy or Or mechanism played a major role in diffusion in brass. If no marker movement should be found, a ring mechanism would be indicated but not assured. Experimental Procedure The alloys used in these experiments, listed in Table I with analyses, were supplied by the Naval Research Laboratory. They were from ingots of 3x3 in. cross-section, heated to 760°C, reduced under a

Jan 1, 1957

ANY suitable characterization of the Utah Copper enterprise (now the Utah Copper Division of Kennecott Copper Corporation) involves the use of superlatives. If comparative records were compiled, after the fashion of baseball, the big opencut mine at Bingham Canyon, Utah, undoubtedly would hold dozens of championships in the mining world. For example, a few can be set down as follows: (1) The mine is the biggest man-made hole (excavation) in the crust of the earth! At the end of 1955 the total quantity of material moved (ore and overburden) was 1,673,000,000 tons or approximately 800,000,000 cubic yards. This is about3% times the yardage of earth moved in the original digging of the Panama Canal. It exceeds by fifty per cent the quantity dug in the justly famous Hull-Rust Mahoning open-pit iron mine on the Mesabi Range in Minnesota. (2) It holds first place among the mines of the world as to aggregate tonnage of ore mined and milled (734,000,000 tons at the end of 1955). (3) It holds first place among the mines of the world as to the aggregate quantity of metal produced (13,047,000,000 Ib- 6,523,500 tons-of refined copper). This is more than the actual production of all the mines in the United States during the eight-year period 1948 to 1955 inclusive. (4) In 1943, Utah established these world records: Tons of ore milled in a 24-hr day.. ................. 108,000 Tons of ore and waste moved in a 24-hr day.. ....... 235,000 Tons of ore milled in one month. ................... 3,074,000 Tons of ore milled in a year. ....................... 35,375,000 Pounds of copper produced in a year……….. 639,0000,000

Jan 1, 1957

By H. W. Mead, C. E. Birchenall

The rates of growth of graphite nodules in cast irons are calculated for a model of a growing graphite sphere surrounded by a shell of austenite through which carbon and iron are diffusing. The carbon is supplied by a cementite-austenite mixture at the outer edge of the shell. The calculated rates from carbon diffusion agree fairly well with the measured values, but the rates based on iron self-diffusion are much too low. Because the iron must be removed for the process to continue, o plastic deformation mechanism is suggested. THERE has been an unfortunate tendency in the literature of growth and dissolution reactions to identify the slope of a plot of the logarithm of the growth or dissolution rate vs reciprocal of temperature with the activation energies determined by diffusion measurements in chemically similar systems. If the solubility limits at the growing or dissolving phase interfaces change appreciably with temperature, such procedures may lead to serious errors in specifying the mechanisms controlling the rates of these processes. A reaction involving the simultaneous growth of graphite from and dissolution of cementite in austenite will be discussed here to show that substantial oversimplifications have been made in earlier studies of this process. From a dilatometric study of the overall y-range graphitization process, Bunin and Danil&apos;chenko&apos; found an apparent activation energy of 90 kcal per g-atom. They concluded that, since this value was much nearer the approximately 68 kcal per g-atom observed for self-diffusion in pure iron than it was to 32 kcal per g-atom for diffusion of carbon in iron, the rate-controlling process must be the diffusion of iron away from the growth interface to provide space for graphite to grow. Bunin and Salli&apos; bolstered this agreement with the observation that graphite forms preferentially at surfaces, cracks, and pores where free volume is present initially. Ziegler, Meinhart, and DeaconQ ad found an apparent activation energy for graphitization of 98 kcal per g-atom. This value, like that of Bunin and Danil&apos;chenko, applies to nucleation and growth occurring simultaneously. It is not generally assumed that nucleation is entirely diffusion-controlled. Treatments such as prior cold-working and prequenching, which strongly affect the rate of graphitization, would be expected to have little effect on diffusion processes occurring at the graphitization temperature. In any case 90 kcal per g-atom is not particularly close to the 54 kcal or lower to be expected for diffusion of iron which is carbon-saturated.&apos; The presence of silicon in iron is said to reduce the activation energy for diffusion,&apos; so its presence in cast irons would be expected to have a similar effect. The growth rates of nearly spherical graphite nodules have been studied by Brown and Hawkes." The initial rate of growth before impingement of adjacent carbon-depleted areas was found to be parabolic, and rate constants were measured at several temperatures. Their apparent activation energy for the growth process only was roughly 45 kcal per mol. Burke and Owen&apos; made growth-rate measurements on several alloys, recording appreciable induction periods, initial nucleation rates, and average radial growth rates based on an assumed linear rate of radial growth. They found that increased silicon content increases the ovel-all reaction rate and the initial rate of nucleation, and decreases the induction period. Assuming 1) spherical nodules. 2) constant volume rate of nucleation, 3) austenite in equilibrium with cementite at positions where the cementite is not depleted, and 4) a constant diffusion distance during the growth of a nodule, they calculated an apparent overall activation energy of 68 kcal per mol, which was related to an activation energy for nucleation of 79 kcal per mol and activation energy

Jan 1, 1957

By J. Gordon Parr, D. H. Polonis

The formation and subsequent decomposition of metastable phases in Ti-Ni alloys containing up to 11 pet (atomic) Ni have been studied. The decomposition of a completely retained ß phase and of a completely transformed 8 phase in a 6 pet alloy has been followed by X-ray diffraction and metallographic methods and by hardness determinations made during the process. The possible mechanisms of the reactions are discussed. PREVIOUS investigations of the Ti-Ni system have usually been limited to phase diagram studies; but little attention has been given to metastable phases and tempering processes. These are important, however, since equilibrium conditions are rarely achieved—nor, perhaps, are they desired—in practice. Up to the present time the available transformation data for titanium alloys appear to be restricted to isothermal transformation curves for selected binary and ternary systems. No quantitative studies have been made of the mechanism by which equilibrium is approached. Several independent investigations have been carried out to determine the Ti-Ni phase diagram. Early work by Wallbaum&apos; and later by Long et al.&apos; produced tentative phase diagrams which were not representative of true binary conditions, since the alloys were contaminated with oxygen and nitrogen. The most recent diagram (Fig. 1) is due to Margolin et al.," and a slight modification of the a + ß/ß boundary (shown dotted) has been proposed by McQuillan.&apos; The structure of the phase Ti,Ni was shown by Duwez and Taylor" to be face-centered-cubic, with 96 atoms per structure cell. The formation of a martensitic ß phase (close-packed-hexagonal) in Ti-Ni alloys has generally been observed when specimens of low nickel content are rapidly cooled from the 0 (body-centered-cubic) range. Margolin et al. reported an increasing tendency for P to be retained in lump specimens as the nickel content increases. McQuillan&apos; has studied the effect on the microstructure of delay time in quenching, and has reported the formation of pro- eutectoid a precipitate in a quenched hypoeutectoid alloy. In a previous study of Ti-Fe alloys," experiments were made on powder specimens produced by filing alloy ingots. Techniques were devised for the preparation and heat treatment of alloys, and X-ray diffraction methods were used both for structure determinations and phase ratio estimations. A similar approach has been made in this study of Ti-Ni alloys. Experimental Methods Ten alloys ranging from 0.25 pet to 18 pet Ni* * All compositions are in atomic percentages unless otherwise stated. were prepared from iodide titanium bar stock (hardness Rf 72) and Johnson-Matthey spectrographic standard nickel by levitation melting.&apos; As a check

Jan 1, 1957

By Robert Corcoran, George Wiener

A study of the orientations and microstructure of 3 pct Si Fe alloys after deformation and recrystallization has been made. The components found after deformation agreed with recently published work on single crystals, being primarily (001) [110], (111) [110], and (111) {112}. A pronounced effect of temperature of recrystalliza-tion was found on microstructure and orientation. Low temperature recrystallization was interpreted in terms of low angle boundaries which resulted in the retention of a large amount of the deformation texture. High temperature recrystallization was interpreted in terms of high angle boundaries which gave rise to new components. No simple angular relation between the deformation and high temperature recrystalliza-tion textures could be detected. DEFORMATION and recrystallization behavior of 3 pct Si-Fe has been the subject of scientific investigation for many years. The fact that it is a single phase body-centered-cubic alloy from room temperature to the melting point permits study over a wide range of temperature without the complications of phase transformations. There is an important commercial interest in this material as well, since it is widely used in the electrical industry. In the present work the deformation and recrystallization behavior of poly crystal line silicon iron has been studied with the primary purpose of evaluating the effect of a second phase impurity on both processes as well as the effect of temperature on the recrystallization characteristics. With regard to deformation, the emphasis has been placed on a study of the crys-

Jan 1, 1957

By I. Fatt

Networks of resistors are used as analog computers to obtain relative permeability and resistivity index curves for networks of tubes. These curves have all of the characteristics of those obtained on porous media and, therefore demonstrate the validity of the network of tubes model. INTRODUCTION In paper I&apos; of this series the network model was shown to give information on the structure of porous media that could not be obtained from the bundle of tubes model. The agreement between the capillary pressure characteristics of a network of tubes and those of typical porous media does not prove the validity of the network made. The bundle of tubes model, although it gives less information, also shows this agreement. In this paper the flow properties of a network of tubes are shown to be in agreement with flow properties of porous media. The flow properties of the bundle of tubes model are not in adequate agreement with those of porous media. The dynamic properties of porous media, such as fluid permeability and electrical conductivity, have been found experimentally to be more sensitive functions of structure and pore size distribution than are the static properties such as porosity and capillary pressure characteristics. The network model can, therefore, be best tested by comparing the dynamic properties of a network of tubes with the observed properties of porous media. All static and dynamic properties of a completely valid model must agree with the observed properties. The most commonly measured sensitive dynamic properties are the relative fluid permeability and the relative electrical resistivity. Experimental measurements of these dynamic properties on sandstone, sintered glass, sintered alumina, and soil are reported in the petroleum and soil science literature. These properties were chosen, therefore, for the test of the network model. In the network model, relative permeability is the permeability of the network when some of the tubes are not conducting fluid, relative to the permeability when all tubes are conducting fluid. Similarly, the relative resistivity is the electrical resistivity of the network of tubes when some of the tubes are filled with a nonconductor. relative to the resistivity when all tubes are filled with the electrical conducting fluid. Single Size Tube Network The simplest porous medium is one in which all pores are of the same size. Such media can be approached by packing beds or columns of uniform size particles of sand, glass, or metal. The model of such medium in this study is a network of single size tubes. The network form, the ß factor, is usually not known for real porous media. If the validity of the network model can be established, then the study of the flow properties

Jan 1, 1957

By K. G. Wikle, J. G. Klein, W. W. Beaver

Consolidation of hydride process, electrolytic, calcium reduced, and comminuted thorium powder, as well as saw chips and lathe turnings, by vacuum hot pressing and by cold pressing-vacuum sintering was studied. The mechanical properties of the consolidated material in the extruded form are compared with those of wrought castings. AT present there little little industrial use for thorium metal, although it has some important though small scale applications in electronic equipment. Despite its high inelting point—about 1750°C —a low modulus of elasticity, 11.4xl0 si at 20°C;&apos; relatively low mechanical properties coupled with a high density, 11.7 g per cu cm; and an unusually high chemical activity with normal atmospheres limit any structural applications. The metal is utilized as an alloying element principally in magnesium. Pure thorium finds utility as electrodes in gaseous discharge lamps such as the high intensity mercury lamp&apos; because its low work function and high electron emissivity provide lower starting potentials and more uniform operating characteristics than other available materials. The metal is also found in photoelectric tubes used for the measurement of the ultraviolet spectrum." Thorium metal has been used in germicidal lamps of the cold cathode type as sputtered coatings on nickel in order to provide a low work function surface and a low starting voltage. Other applications have involved the radioactive properties of thorium for the production of ionized particles." The potential value of thorium is much greater than its present use pattern because of possible utility in the field of nuclear power. Th may be converted through nuclear reaction to a fissionable element U which should be capable of acting similarly to U in the g&apos;eneration of atomic power. Thorium has been reported to be about three times as plentiful as uranium in the earth&apos;s crust, placing it in the order of abundance of lead and molybdenum." Thus, it is of interest in augmenting the potential supply of fissionable material for nuclear power. Because of its high melting point, thorium is usually produced as a powder through the calcium reduction of its oxide or thermal reduction of halides by sodium, magnesium, and calcium. It may also be produced in flake form by electrolysis of fused alkali or alkaline earth chloricles and fluorides. Therefore, powder metallurgy assumes importance in the fab- rication of thorium metal shapes. Furthermore, it is rather difficult to obtain pure thorium by melting, as the molten metal reacts readily with graphite as well as oxide, carbide, and nitride refractories. These contaminate the melt with oxides, carbides, and metallic impurities." The current investigation was undertaken to examine the fabrication of thorium by powder metallurgy methods which have been used for the commercial production of beryllium and other metals.&apos; A sparcity of data concerning the comparative cold and hot compaction of thorium powders of different derivation existed. Therefore, all commercially available types were examined along with other experimentally produced thorium powders in order to round out the comparison of consolidated thorium powders with melted reguline metal. Review of the Literature By heating a mixture of ThC1, with potassium, Berzelius made the first thorium metal as an impure powder in 1828. Improvements in the basic process, increasing thorium assay to 99 pct, were made by several investigators including Arsem," Lely and Hamberger10 and Von Bolton." Calcium reduction of Tho, to make powders was investigated by Berger," Huppertz,&apos;" Kroll," and Kuzel and Wedekind.&apos;" A thorium powder produced by this method using a CaC1, fluxing agent assayed 99.7 pct, as reported by Marden and Rentschler.&apos;" Compacted and sintered, this product was found to be ductile, and could be fabricated into wire and sheet. Improvements of the calcium reduction process were made later" wherein CaCl, was eliminated from the reaction, producing metal assaying 99.8 pct Th. Further work by Lilliendah118 howed that a coarser metal could be obtained by the substitution of ThC1, or ThOC1, for oxide with consequent advantage of stability to atmospheric reaction. Reports on the technology of thorium developed in Germany during World War II have been made by Espe."&apos; Thorium powder of 99.5 pct Th was obtained by reduction of the oxide by calcium. Screening to —200 mesh, compacting with about 20 tsi, and sintering in vacuo at 1320" to 1360°C for 3 hr resulted in a porous sinter cake. The sinter cake was sufficiently ductile to be worked into bar, wire, and sheet which could be employed as electrode materials.

Jan 1, 1957

By L. F. Stutzman, George Thodos

The friction factor plot presented by Cornell and Katz4 and developed for the flow of fluids through consolidated formations has been directly adapted for handling fluid flow problems involvitrg both linear and radial flow. In this adaptation the friction factor plot is used directly for the solution of problems and thereby eliminates the use of conventional equations which are specific to laminar (Darcy) or turbutent flow. This upproach overcomes the disadvantages inherent in the use of these conventional equations. It eliminates the necessity of checking the type of flow occurring in order to identify the specific equation which must be used. In radial flow problems, because of the increasing mass velocity of the fluids as they approach the wellbore. the type of flow may no longer remain laminar. Consequently, it is necessary to use more than one equation in a problem and to identify the range over which each equation should be applied. Finally, in practice it has been found that much of the flow of gases through consolidated media occurs in a range that is neither laminar or turbulent. For this transitional region, no convenient equations are available. The method and presented friction factor plot are appficahle to both liquids and gases. INTRODUCTION The flow of fluids through unconsolidated media in packed beds has been treated extensively by a number of investigatorsl,2,3,5,7,8 Most of these studies present friction factors as a function of modified Reynolds number similar to those developed for conventional fluid flow through pipes. These friction factor plots are presented for linear flow; however, Elenbaas and Katz have extended these concepts to apply to radial flow. All of these studies on unconsolidated materials require a knowledge of packing properties such as sphericity. porosity, and particle diameter. Sphericity and particle diameter cannot be defined at the present time for consolidated formations such as those commonly found in gas or oil reservoirs. As a result many investigators have not utilized friction factors and Reynolds number in the study of fluid flow through consolidated media. However, Cornell and Katz4 present a plot (Fig. 1) for the flow of fluids through consolidated porous media, in which the friction factor defined as: The turbulence coefficient, P, is related to the formation permeability, K, as presented in Fig. 2. Three different types of flow may exist in the flow ot

Jan 1, 1957

By H. Hansen, A. U. Seybolt, P. Yurcisin, B. W. Roberts

The Bi-Mn phase diagram in the region near BiMn was investigated, using principally thermal analysis and changes in magnetization with temperature. Of chief interest are the findings related to the magnetic transformation in Bi-Mn. THE Bi-Mn system is of both theoretical and practical interest because of the occurrence of the compound BiMn which exhibits unusual ferromagnetic properties. Because the Bi-Mn phase diagram reviewed by Hansen&apos; (see Fig. 1) in 1936 is based on work done by BekierY in 1914 and by Siebe" in 1919, which left considerable doubt about the nature of the diagram. it appeared desirable as an aid in understanding the alloying characteristics and magnetic behavior to examine the pertinent regions of the phase diagram. The most interesting reaction is the peritectic at 445°C which forms BiMn by the reaction: Liquid + Mn(sulfield) ? BiMn(sol field) There is also a eutectic at 262° C between pure bismuth and BiMn. Hansen draws in BiMn dotted, since in 1936 evidence for its existence was uncertain. Experimental Materials—Preparation of Alloys Electrolytic manganese of about 99.97 pet purity and bismuth of 99.99 + pet purity were used as starting materials.

Jan 1, 1957

Jan 1, 1957