Search Documents

By John M. Hird

A section of unstable overburden that has hampered an all-dragline mining operations at Texasgulf's phosphate mine in eastern North Carolina, is being successfully removed by hydraulic dredging. Blocks are dredged, drained, and developed ahead of two large draglines that strip the remaining overburden and mine the 12-m section of ore. Dredging assistance has increased ore production, increased ore recoveries to a maximum, reduced unit costs, and has made it possible to reclaim mined-over land that would be left underwater mined by all dragline methods.

Jan 1, 1981

By Roger Thunvik, Carol Braester

Excavation of cavities below the ground water level induces water influx from the surrounding aquifer. An estimate of the rates of flow prior to excavation operations may be of valuable information for the mining engineer. The present paper deals with water influx into cavities of the tunnel type, e.g., mine galleries, tunnels, etc. The solution of the flow problem was obtained by a numerical finite difference method. The results are presented in dimensionless form as a function of the parameters characterizing the location of the cavity in the aquifer.

Jan 1, 1981

El Indio, eighty percent -owned by Compania Minera an Jose Inc., a subsidiary of St. Joe Minerals, and twenty percent-owned by private Chilean investors, will open their new flotation and Carbon -In -Pulp plant near La Serena, 480 km (300 miles) north of Santiago, Chile, in early 1981. The underground mine, at an altitude of 4,270 m (14,000 ft), will produce about 1,270 mt per day (1,400 st per day) of ore containing about 2. 2570 Cu, and gold and silver to the extent of 16 and 254 g per mt (0.47 and 7.4 oz per st) respectively. While construction of the plant was underway, development ore, containing some 1,400 kg (45,000 oz) of gold, was shipped to the United States for recovery in a copper smelter. At El Indio the underground ore is rail-hauled to the mill a short distance from the portal where it is crushed, ground, and floated to produce a copper concentrate containing both gold and silver. The crushing plant also crushes waste for use as mine backfill. Approximately 92% of the copper and 60% of the gold and silver are recovered in the flotation concentrate. Flotation tailings, at a grade of 19 g Au and 116 g Ag per mt (3.4 oz Au and 0.55 oz Ag per st), are cyanided for 72 hours in six Pachucas with auxiliary air lifts for pulp transfer. Lime, cyanide, lead nitrate, and a phosphate are also fed to the cyanidation Pachucas. After cyanidation, the pulp is treated in four air lift Carbon-In-Pulp tanks equipped with external vibrating screens for carbon advance. Loaded carbon is stripped in two pressure vessels in parallel. Pressure stripping must be used because of the high altitude. Stripped carbon is dewatered in a spiral classifier before being reactivated in a rotary kiln and returned to the C. I. P. circuit. Pregnant solution is then sent to four banks of four Zadra cells for gold and silver recovery on steel wool. Zadra cell cathodes.are washed with the slimes being captured in a plate and frame filter. The filter cake and the washed cathodes are then dried on an infrared dryer and smelted in two stages to bullion bars. Published reports indicate that the total investment for this unique operation was in the neighborhood of $80 million.

Jan 1, 1981

By J. Wes Blakely

In the mid-1950s the importation of foreign oil began to encroach on traditional coal markets such as railroad steam engine fuel, home heating, electrical generating plants, and others. Many of the smaller coal companies with substantial coal reserves subsequently found that they could no longer continue to mine economically and merged in various ways with larger established coal mining concerns. As the seats of top management and authority were removed from the mines to large metro centers such as New York, Pittsburgh, and Chicago, the more personal relationship between mine workers and management that had existed prior to these mergers began to be eroded and replaced by "remote control" mine management. The disappearance of this face-to-face contact of upper management with mine employees tended to create barriers blocking simple effective communications between coal mine management and labor. In examining the human relations aspects of the coal mining industry, many elements, some concerned with work and others not, have depicted the industry as almost devoid of good applied human relations and communications practices, and, in truth, little has been done to alleviate this situation. In past years many coal producing companies, with the exception of one of the largest, failed to adequately define the term "communications ' as it applied to their companies, whether internally or externally. Internally many still place heavy reliance on written communications such as company-wide newspapers to do the job of communicating with their employees which they feel ought to be done. One company puts an inordinate belief in its company "newspaper" as the primary instrument to stimulate its work force into increasing productivity. Primarily aimed at the workers, who greatly outnumber the salaried administrative people, this publication mainly documents the fortunes of individual mine workers who are felt to have achieved something with their lives, e.g., a mine worker who had managed to put four children through universities, the

Jan 1, 1981

By Martin C. Kuhn, Lawrence G. Stevens, J. Mark Richardson

The majority of the world's known and anticipated reserves of nickel ores are lateritic deposits At present, there are several different process alternatives for recovering nickel and other desired metal values from laterite ores An overview is given of the selective reduction roast/ammoniacal leach process, one of the processes in commercial operation.

Jan 1, 1981

By Jasinder S. Jaspal, John A. Reeves, Bradley J. Bourquin

INTRODUCTION The United States has an abundance of coal reserves in thick seams. Most of these resources are in the West. Surface mining operations in thick seams are highly efficient, particularly in the West, but methods for mining thick seams underground are very limited. The percentage of resource recovery in deep mining of thick seams is often as low as 30 percent. It is estimated that there are 45 billion tons of coal reserves for underground mining in seams greater than 10-ft thick in the western states alone. With such a large available reserve base and low rates of recovery, the need to develop the technology to mine these thick reserves is quite evident. As the definition of a thick seam varies widely from country to country, a thick seam is defined here as any seam where the height is such that it is not minable in a single pass with available mining equipment.

Jan 1, 1981

By D. S. Choi, D. L. McCain

A method of estimating the chain pillar size required to support the wide working faces of longwall or shortwall coal mining is presented. The pillar size is determined through the use of coal strength, entry geometry, panel width, and overburden pressure. Design analysis is focused on a three-entry development system in the Pittsburgh Seam but can be used for other development plans and other seams by substitution of the proper geometric and strength data.

Jan 1, 1981

By J. Eric Belford

The Kidd Creek orebody is a massive base metal sulphide deposit with surface dimensions of 168 m by 670 m. The steeply dipping ore- body has been evaluated to a depth of 1 524 m. To date, the mining of the orebody has been divided into three stages. The first stage of mining was an open pit operation which supplied ore from 1966 until 1977 when a depth of 219 m was reached at the widest or north end of the orebody. The second stage of mining, called No.1 Mine, was the development of an underground mine to replace the pit and recover the ore from the floor of the pit to a depth of 792 m. Development of the underground mine started in 1969. Full production of 273 000 tonnes per month was attained in 1977. The third stage of mining called No.2 Mine, was initiated to accommodate a production expansion and included the development of a second underground mining operation to recover the ore from the bottom of No.1 Mine, i.e. the 2600 level; to a depth as yet undetermined but most likely the 4600 foot level. Development of the No.2 Mine began in 1974. Full production of 91 000 tonnes per month will be achieved in 1982. The choice of the 2800 level as the partition between the two underground mines was based on the following factors: The 2600 level is the lowest level which can conveniently be mined through the No.1 Mine crusher on the 2800 level. Development and trial stoping methods for mining at depth could be evaluated in the 2600 to 2800 block utilizing the existing hoisting facilities of No.1 Mine. Early development of the ore in the 2600 to 2800 block would provide additional mill feed sooner than could be achieved by developing from No.2 Shaft. The underground mining plan then is to mine from the pit floor down to the 2600 foot level and at the same time mine from the 2800 level down to at least the 4600 foot level. PLANNING The Kidd Creek operations are designed to follow a logical mining sequence. The grade of ore supplied to the concentrator is the result of following the mining plan. The philosophy of mining has been to mine downward in horizontal slices. In the case of No.1 Mine the slices are 122 m thick while in No.2 Mine the slices will be 183 m thick. The point of this approach is to mine the pillars immediately after creating them rather than allowing them to stand, deteriorate and generate uncontrollable situations. Two types of ore are handled separately to optimize recoverable values in concentrates. The 'A' type ore is a copper zinc ore with some silver and little lead. The 'C' type ore is a zinc silver ore with some lead and copper

Jan 1, 1981

Smoky Valley Mining Company, Round Mountain, Nevada, was the pioneer operation designed for large scale heap leaching of crushed gold ores. It is located in the Big Smoky Valley which stretches 160 km (100 miles) through central Nevada west of the Toiyabe Mountain Range. Gold was first-discovered at Round Mountain, 88 km (55 miles) north of Tonopah, in 1905; and mining in the area included placer operations, which ran from 1946 to about 1960. Smoky Valley Mining Company is a partnership of Felmont Oil Co., Case-Pomeroy & Co., and Copper Range Co., with the latter being wholly owned by Louisiana Land and Exploration Co. In 1969, an option on the Round Mountain property was acquired by Copper Range, and during 1974 a decision was reached to proceed with mine development and plant construction. Ore reserves were reported at 10,537,000 mt (1 1,617,000 st) of 2.09 g per mt (0. 061 oz per ton) gold using a cut- off grade of 0.69 g (0.02 oz). Silver content was approximately 2.4 g per mt (0.07 oz per ton) and the waste to ore ratio was about 1: 1. By the end of 1976 heap leaching was in operation. The ore is a rhyolite tuff, sometimes described as a gold porphyry with highly abrasive qualities but which does not break down into slimes upon contact .with cyanide solutions. Gold is unevenly distributed through the ore but as a whole it is in a very finely divided state. Climatic conditions are extreme in central Nevada. Summers are hot and dry while winters are windy and cold with subfreezing temperatures. Elevation of the property is about 1,920 m (6,300 ft). Precipitation averages 203 mm (8 in.) per year. Until February of 1980, leaching was continued until the temperature reached minus 2ºC (28º F), and about 10 months leaching was the average. Water for the operation is drawn from the Toiyabe Mountains through a 13. 7 km (8. 5 mile) pipeline, originally installed in 1915, or from wells in the valley bottom. The plant requires make-up water at the rate of about 1,500 liters per min (400 gpm). On a schedule of three shifts, seven days per week, the daily output at Round Mountain amounts ,to 12, 700 mt (14, 000 st) consisting of 6,350 mt (7,000 st) each of ore and waste. Ore is hauled with a fleet of 45 mt (50 st) trucks and dumped into the 1,0.70 by 1,650 mm (42 by 65 in. ) gyratory primary crusher located near the pit. The primary

Jan 1, 1981

By L. R. Mabson, F. M. Russell

INRODUCTION Roan Consolidated Mines Limited (RCM) operates five underground mines - Mufulira, Luanshya, Baluba, Chambeshi and Chibuluma (figure 1) . Associated metallurgical plants provide for the operations of milling, smelting two refineries for copper and a cobalt plant. Primarily a producer of high quality copper (242,000 tonnes during 1980) the Company is also the world's second largest producer of cobalt metal. RCM's remaining ore reserves at 31st March 1980 were 275 million tonnes at 2.84% copper. Monthly ore production is in excess of 1.2 million tonnes. Sublevel open stoping was the choice of mining method for the first underground operations on the Copperbelt for ore with dips steeper than 30 degrees. This was for use at the Roan Antelope mine, subsequently to be called Luanshya mine. The sublevel open stoping system was planned based on the methods used in many of the iron mines of Michigan and New York and in the copper mines of Tennessee. Peterson (Ref. 1) gave the following reasons for employing sublevel stoping, reasons which are still valid today: (1) the working place could always be barred and made safe, and the sublevel exit was always at hand; (2) the working conditions were similar day by day and drilling operations were repetitive; (3) pillar spacing can be varied as conditions demand; and (4) stoping operations could be shut down completely or opened up to full capacity at short notice, without affecting grade or causing wastage of reserves. Such was the success of the method that it was adopted as the basic mining method at all the RCM mines in their initial stages. Although cut and fill, block caving, and sub- level caving methods have been used, sublevel open stoping in its many variants still accounts for nearly 90% of total ore production in the Company. The following descriptions outline some of the applications of sublevel open stoping within RCM. LUANSHYA Geology There are two main ore deposits at Luanshya: the Roan (Luanshya Mining Area), in which mining began in 1930, and Baluba, in which mining production started in 1973 (figure 2). Both orebodies occur in synclinal and variably folded basins. These basins are underlain and completely surrounded by much older schists and granites. The ore formation, an argillite, lies near the base of the sediments and is underlain by conglomerates, quartzites and arkoses. Copper mineralisation is mainly found in two well defined zones, separated by a varying thickness of pyrite mineralisation. In the eastern part of the Roan deposit only the upper orebody is present, but west of 18 shaft and at Baluba the lower orebody predominates. Locally the subjacent quartzites of the footwall formation are also mineralised with copper. The copper mineralisation is found princi- pally as disseminated sulphides, mainly chalcocite, bornite and chalcopyrite. Near the surface the sulphides have been changed to oxides. At Baluba the cobalt mineral carrollite is found with the sulphides. Mining methods Sublevel open stoping is the basic mining method. In its standard form this method is best suited to steeply inclined orebodies, with simple structures and with a strong foot- wall and hangingwall. In recent years, as more complex folding and flatter dipping orebodies have been encountered, considerable variations have been introduced. Stope drilling is effected with drifters and extension steel.

Jan 1, 1981

By S. K. Bose, P. K. Sahoo, S. C. Sircar, P. K. Jena

High grade manganese ores are utilized in metallurgical, chemical, and battery industries, whereas the low grade ores are not accepted for these purposes and hence get accumulated at the minehead. In the present study an attempt was made to solubilize the manganese value as its sulfate by roasting the low grade ore with a suitable sulfatizing agent followed by water leaching. The different parameters were determined in the laboratory scale. Based on these, kilogram scale experiments were conducted where an appreciable amount of manganese goes into solution during leaching.

Jan 1, 1981

Cortez Gold Mines operated a conventional 2,100 mtpd (2, 300 stpd) cyanidation plant until the 5 million ton ore body was worked out in 1973. (See Gold and Silver Cyanidation Plant Practice by F. W. McQuiston, Jr. and R. S. Shoemaker, Society of Mining Engineers, AIME 1975.) Sub-grade material was dump leached at the mine -mill location in 1971, and the resulting pregnant solutions were added to the feed in the plant's Merrill-Crowe precipitation unit for gold recovery. In early 1973, however, Cortez put into operation their Gold Acres mine which was located about 13 krn (8 miles) to the west of the 'Cortez mine. Economics at that time dictated the heap leaching of the lower grade portion of the ore body with the higher grade being trucked to the Cortez plant for milling. Leach ore was moved directly from the open pits to prepared leach pads located on a gently sloping terrain of 570 grade. Preliminary pad preparation at the leach site included removal of vegetation which was composed of sagebrush and grading of the base. Pads were comprised of mostly minus 74 micron (200 mesh) materials and were made of clay-silt or slime tailings spread on the pad area in thin 50 to 75 mm (2 to 3 in. ) layers, compacted with a vibrating roller compactor to a depth of about 380 mm (15 in.). This was followed with a 100 mrn (4 in.) layer of coarse rock to prevent erosion on the pad and to allow solutions to move laterally under the heaps. Leach solutions normally traveled the length of the heaps and were collected in plastic-lined ditches from which they flowed by gravity to the pregnant solution storage pond. Both pregnant and barren ponds were constructed in the same manner as the leach pads - being lined with compacted tailings or clay silts. The Gold Acres facility required pregnant solution storage of 6 million liters (1.6 million gal) and barren storage of 3.8 million liters (1.0 million gal) designed to handle two to three days of heap drainage or to retain run-off from a major rainfall. Various heap heights were tried including 3, 6, and 9 meters (10, 20, and 30 ft), with a 6 m (20 ft) height selected. Ore was dumped by trucks in a single 6 m (20 ft) lift using a D8 Caterpillar dozer for

Jan 1, 1981

By W. H. Lewis, J. C. Yingling, M. H. Leon

This paper describes the present state-of-the-art and status of longwall lighting in the U.S.A. Specific subtopics discussed are as follows: review of MSHA lighting regulations and requirements for longwalls; overview of available lighting hardware; installation procedures and costs; analysis of installations to date, including operator and management acceptance, complaints, benefits, and maintenance considerations.

Jan 1, 1981

By T. O. Olsen, R. Henriksen

Aggregated models of a bank of flotation cells have frequently been used, assuming that a single-cell model can be used for control and estimation purposes. In this paper we investigate the feasibility of this approach, and show that single-cell aggregated models may very well be used in order to estimate the aggregated net flotation rate constants of the bank. These estimates would usually be very crucial in order to control the plant.

Jan 1, 1981

By Renato G. Bautista, KNona C. Liddell

A model of the reaction of chalcopyrite, CuFeS2, with Fe3+ and with 02 is considered. Homogeneous solution phase reactions are assumed to be always at equilibrium throughout the dissolution of the mineral. The dissociation of USOb- and several complexation reactions involving cu2+, Fez+ and Fe3+ are incorporated in the model equations. The relative importance of Fe3+, 02, and H+ as oxidants and the role of solution equilibria are assessed and the implications for leaching practice discussed.

Jan 1, 1981

By Douglas A. Sloan

Who would believe that young elementary school children could understand something as complex as the mining industry? The Challenge The challenge of accomplishing this is tremendous. An examination of Canadian school children indicated that they knew very little about the world of work in general, and hardly anything about the mineral resource industry in particular. It calls to mind the story about two youngsters who decided to play house. The little girl played her role well as she went about the house doing things she had watched her mother do every day. When it was the little boy's turn, he grabbed his lunch, waved goodbye to his "wife," jumped on his bicycle and pedalled furiously down to the end of the driveway-where he stopped. The youngster explained that he saw his dad go out of the driveway each morning, but he didn't know where he went, or what he did on the job. When you stop to consider the number of families today with two working parents, you can begin to appreciate the importance of the opportunities for role identity provided by this project. The Approach The challenge of teaching the school children of Canada about the world of work and, specifically, the mining industry is the challenge which the Canadian Institute of Mining and Metallurgy met with the Curriculum Development Research project. It started when a small, dedicated group of Vancouver members met Dr. Doreen Binnington. After this meeting, Dr. Binnington, an expert in curriculum development at the University of British Columbia, set herself to develop a curriculum program for the elementary shcools which accomplishes two main goals: It uses the "Identity Approach," developed by Dr. Binnington, an expert in curriculum development at the enable students to understand and appreciate the contribution of people, in this case, working with mineral resources. It has pupils enthusiastically exploring the importance of rocks, minerals, and the mining industry in their lives [(Fig. 1)]. Evolution of the Curriculum Development Research Project When the curriculum development research project was presented to the Vancouver Branch of the Canadian Institute of

Jan 1, 1981

By Anthony Sharkey

Introduction In Europe, longwall mining accounts for over 95% of coal produced from deep mines, whereas in the U.S.A., longwall accounts for less than 5% of deep mine coal production. There are many reasons for the difference, but in general: a. U.S. mine operators have invested heavily in continuous mining or conventional equipment which continues to produce acceptable results; b. There 1s a reluctance to change from, a familiar (and proven) mining method to an unfamiliar one, despite promises of huge production increases,; c. Multi-seam mining in Europe has made longwall the only really viable mining method, whereas In the U.S.A. multi-seam mining (particularly in "below-drainage" mines), is relatively rare; d. Although some spectacular results have been achieved by longwall in the U.S.A.(I), the general performance of longwall in this country has not been good enough to generate much enthusiasm for its wide application; e. The much higher level of investment in face equipment required for longwall when compared to alternative methods (approximately $7.5 million for a medium seam longwall installation and $1 million to $1.5 million for a continuous miner section). However, declining productivity, national energy requirements and safety legislation are creating a situation in which longwall as a viable mining method is being examined more closely and in more places than hitherto. This paper, therefore, attempts to identify some of the principal criteria needing examination in any assessment of the feasibility of longwall application, the limitations of information for those criteria in the decision making process and the need for further research and development to assist the mine operators make the decisions.

Jan 1, 1981

By Dale C. Matthews, Donald L. Simpson

Hecla Mining Company's Lakeshore Mine and Metallurgical complex near Casa Grande, Arizona, is the first plant in North America to utilize the roast/leach/electrowinning process for production of cathode copper from sulfide concentrates. Oxide copper ores are also mined at Lakeshore. Using sulfuric acid and sponge iron by-products of the roast/leach operation, the oxide ore is leached in vats, the copper is precipitated with iron and recovered as cement copper. This paper will describe the roast/leach facilities and discuss the operating conditions at which more than 95 percent of the copper in concentrate is made soluble in acid solutions while less than 5 percent of the iron is rendered soluble. More than 97 percent of the sulfur contained in concentrate is captured either as strong sulfuric acid or as soluble sulfates in leach liquors. The iron rich residue after leaching is pelletized and reduced to sponge iron in an SLRN reduction kiln.

Jan 1, 1981

By C. P. Melloy

INTRODUCTION Ventilation practice at Isa Mine has been evolving since underground mining began in 1931. Much fundamental work has been conducted and reported regarding the primary ventilation system [Mathews K.E. et a1 (1967) and Brown J.R., Fisher T.H., Gibson K.L. (1979) 1. However, ventilation networks for subsystems such as open stopes, have evolved with experience. This paper outlines current ventilation practice for open stoping. Mount Isa Mine The mine is located in semi-arid North-West Queensland, Australia, and currently produces 20 000 tonnes of copper ore and 10 000 tonnes of silver-lead-zinc ore daily in each five day working week. Mining extends over a north-south strike length of 3.5 km with a maximum width across dip approaching 1 km, and is to a depth of 960 m (Figure 1). At present approximately 90% of the mine's copper production is from the 1100 Orebody, which contains ore reserves of 121 million tonnes of 3.2% copper. Open stoping is currently the mining method employed, and is used for primary stoping and pillar recovery adjacent to cement fill walls. The development of stoping methods in the 1100 Orebody has been documented by Kirkby R.W., Blair J.R., and Hutton R.C. (19781, Hornsby B. and Sullivan B.J. (1978), and Alexander E.G. and Fabjanczyk M.W (1981). As many as thirteen open stopes may be producing concurrently in the Orebody (Figure 2). The multiple silver-lead-zinc orebodies containing reserves of 54 million tonnes of 150 g/t silver, 6.4% lead and 6.5% zinc, are mined by open stoping, and cut and fill techniques. These methods have been documented by Goddard I.A. and Bridges M.C. (1977 1, and Goddard I. A. (1981 1. Only the ventilation of the 1100 Orebody open stopes will be discussed. However, the same ventilation philosophy is employed in open stope design in the lead orebodies.

Jan 1, 1981

By L. T. Larson, P. M. Basinski

In the northern Reese River Valley uranium is corroded with Middle Pliocene zeolites. These zeolites were diagenetically derived from rhyolitic volcanic glass deposited in a saline- alkaline lake. X-ray diffraction, scanning electron microscopy, and chemical studies reveal clinoptilolite, analcime, and enonite to be pesent and that these minerals can concentrate at least 0.7% uranium from solution. Most anomalous drill cuttings contain zeolite and zeolites are believed to host the uranium. Research suggests the uranium mineralization is conceptually analogous to the Tono mine, Japan.

Jan 1, 1981