Search Documents

By T. W. Watson, D. R. Flynn

Measurements have been made of the thermal conductivity and electrical resistivity of two specimens of 0.005-cm (2-mil) Be-Cufoil over the temperature range -140° to +200°C. The thermal cmductivity of Be-Cu Alloy 125 was found to be significantly higher than that of Alloy 25, which had a higher impurity content. The thermal conductivity and electrical resistivity values obtained were in concordance with the Smith and Palmer relation for copper alloys which states that ? = 0.0239 (T/p) + 0.075 where A is thermal conductivity (W cm-' deg-'), p is electrical resistivity (microhm-cm), and T is absolute temperature (OK) , indicating that the Smith and Palmer relation can be used to predict the thermal conductivity of this type of Be-Cu alloy over the temperature range -140" to + 200°C to within an accuracy suitable for most engineering applications. THE National Aeronautics and Space Administration, Goddard Space Flight Center, Greenbelt, Md., requested the National Bureau of Standards to measure the thermal conductivity of 0.005-cm Be-Cu foil which was to be used to fabricate antennae for use in Radio Astronomy Explorer space craft. It was felt that measurements had to be made on the actual antenna material, rather than on a thick bar of similar material, since the cold-working and age-hardening properties of the alloy would make it very difficult, if not impossible, to place a thick bar in the same metallurgical state as the 0.005-cm material. As discussed in Section 111 of this paper, the thermal conductivity of many copper alloys can be computed rather accurately from electrical resistivity data using an empirical relation developed by Smith and palmer' and further confirmed by owell.' However, there has been very little work done on correlating thermal and electrical conductivities on Be-Cu alloys. We were reluctant to assume the validity of the Smith-Palmer relation on Be-Cu alloys because of the very large mass difference between beryllium and copper. As will be seen, however, our experimental results indicate that the Smith-Palmer relation is valid for the two alloys on which we made measurements. I) DESCRIPTION OF SAMPLES Samples of Be-Cu Alloy 25 and Be-Cu Alloy 125 were furnished to NBS in the form of rolled strip material, 0.005 cm thick by 5.08 cm wide. The Be-Cu Alloy 25 was purchased by NBS in the form of a continuous length of flat strip. The Be-Cu Alloy 125 was furnished to NBS by Goddard Space Flight Center in the form of two lengths of strip that had been formed into "tubing" of about 1.2 cm diam, with one side of the strip overlapping (but not connected to) the other side by about 90 deg. This "tubing" had been opened up to be flat and then rolled onto spools of about 3 cm diam. When unrolled, the strip would spring back into tubular form. Samples of both of the Be-Cu alloys were chemically analyzed by the NBS Analytical Chemistry Division. The beryllium content was determined quantitatively by the phosphate-gravimetric method to be 1.83 wt pct for Alloy 25 and 1.80 wt pct for Alloy 125. The two alloys were also examined by a general qualitative spectrochemical method for metallic elements. The Alloy 25 specimen contained between 0.1 and 1.0 wt pct Al, Co, Fe, and Si and between 0.01 and 0.1 pct Ni. The Alloy 125 specimen contained between 0.1 and 1.0 pct Co and between 0.01 and 0.1 pct Al, Fe, and Si. Other metallic elements present were in amounts less than 0.01 pct. The NBS Engineering Metallurgy Section measured the tensile strength, elongation, and Knoop hardness of both the Be-Cu Alloy 25 and the Be-Cu Alloy 125. These are given in Table I. The NBS Engineering Metallurgy Section also prepared photomicrographs of the two alloys; these are shown in Figs. 1 and 2.

Jan 1, 1969

By Linda P. Bono

Some mining engineers are pursuing their destinies in places far removed from what they might have envisioned back in the classroom. The path they follow to work each day may wind down Wall St., Park Avenue, LaSalle, or Market; their offices are in modern skyscrapers which offer all the amenities-air conditioning, thick carpets, attractive decor, and executive lunchrooms, to name just a few. The papers on their desks are a combination of financial figures and feasibility studies. But even in these surroundings there are indications of what these men do and where their professional interests lie-minerals are everywhere, from vast collections to one symbolic paperweight. . . there are sometimes specks of dirt under fingernails from a recent on-site inspection, belying the traditional banker's garb. . . and there are the wistful comments about finding it necessary to get out in the field.

Jan 9, 1978

By J. G. Morlet, A. R. Troiano, H. H. Johnson

Delayed failure in steel occurs by controlled initiation and growth of a crack. The incubation period for crack initiation was measured. Crack initiation and Propagation are controlled by interaction between hydrogen concentration and triaxial stress state. The incubation period results from stress-induced diffusion of hydrogen to the point of crack initiation. THIS paper describes the phenomenon of delayed failureland the kinetics of crack initiation and propagation in uniformly hydrogenated steel. The investigation was prompted by service failures of high-strength-steel components at applied stresses far below the conventional yield strength, after the part had successfully sustained equal or higher stresses for an extended time interval. This delayed failure phenomenon, often termed static fatigue, is associated1 with the presence of hydrogen. This is not surprising, since the voluminous literature on flaking and hydrogen embrit-tlement demonstrates that hydrogen may exert a potent embrittling influence. Flakes, or internal hairline cracks in alloy-steel forgings, are related to the presence of hydrogen retained from the steel-making process.2 On the other hand, embrit-tlement arises from hydrogen introduced during surface treatments such as acid pickling or electroplating. Laboratory delayed failures have been induced in notch specimens of 4340 steel by electrolytic charging of the specimen surface with hydrogen and subsequent static stressing.l,4,5 Static fatigue was observed over a wide range of applied stresses; however, failure did not occur below a critical applied stress, designated as the static fatigue limit. In this instance the extended time for failure resulted primarily from the macroscopic redistribution of hydrogen. A crack formed to the depth of the hydrogen enriched "case* upon loading; further crack growth naturally awaited diffusion of hydrogen into the material ahead of the crack. The crack-propagation rate was therefore controlled primarily by the macroscopic diffusion of hydrogen into the specimen interior during the test. Thus, in this instance static fatigue was associated with the movement of a gross concentration gradient. However, delayed failure in steel of uniform hydrogen concentration is of greater fundamental interest, as well as commercial significance. With a homogeneous hydrogen distribution a different mode of delayed failure might be expected. As the heterogeneous hydrogen distribution became more uniform,4,5 the initial crack-propagation rate decreased markedly and, in fact, what appeared to be an incubation period for crack initiation was observed. However, the macroscopic concentration gradient precluded an accurate evaluation of these observations. Although the existence of an incubation period, up to this time, has not been established definitely, it is not amiss to point out some implications of the concept. It is of interest in all hydrogen-induced embrittlement phenomena, such as flaking, delayed failure, and hydrogen embrittlement. Much discussion has centered around the possibility of an

Jan 1, 1959

By Russell C., Fleming

FOK, many years the officials of the Magma Copper Co. mine at Superior, Ariz., have had to contend with adverse conditions underground in the form of high rock temperatures, hot water, and high relative humidity. These conditions in the mine have been such that working the mine would have been impossible were it not for the constantly expanding and improved sys- tem of ventilation to produce bearable conditions in the working places. Results that have already been achieved make an interesting study of what can be done along those lines. From the time the mine was first opened in 1910 it has been hot. An idea of the conditions that have persistently been encountered can be obtained from parts of the mine that are not being worked at present or that do not yet have sufficient ventilation. Virgin rock temperatures as determined in drill holes at the faces range from 104° to 116°*. An observation made at the face of No. 5 West footwall drift on the 2800-ft. level.

Jan 1, 1930

By Stephen Birch

The Chitina mining district of Alaska is located at the headwaters of the Chitina and Copper Rivers. At present, the only producing mining properties are the mines of the Kennecott Copper Corpn. and the Mother Lode Coalition Co., which are situated 196 miles from Cordova, the port of entry. The first claims, later acquired by the Kennecott Mines Co. and afterwards transferred to the Kennecott Copper Corpn., were discovered in 1900. The Copper River & Northwestern Ry., which connects the mines with tide water at Cordova, was completed in the spring of 1911. Contemporary with the construction of the railroad, aerial tram equipment was brought to the mines by pack train and a tramway, 3 miles long, connecting Bonanza mine with the proposed railroad terminal, was finished, enabling shipments of high-grade ore to be made immediately the railroad was completed. A mill to treat the lower grade ore was begun the same year. The Kennecott company's holdings consist of 111 mineral claims. The Mother Lode Coalition Mines Co., which is controlled by the Kennecott Copper Corpn., owns 73 claims adjoining the Kennecott holdings. All data on operations and geology refer equally well to the Mother Lode property. Geology The general geology of the district has been covered by the U. S. Geological Survey1 and the geological features of the mines have been carefully studied by A. M. Bateman, in his capacity as consulting geologist to the company.2

Jan 1, 1925

By M. W. Hayward

THE object of this paper is to record and tabulate the data and field observations obtained by the writers and their associates during 10 years of intensive study of lead-zinc deposits in the Cretaceous limestone areas in Northern Mexico, particularly in mines owned by the Cia Minera de Peñoles, S. A. At the El Paso meeting of the Institute in October, 1930, J. G. Barry made the suggestion that a committee be appointed to correlate the ideas and theories which have been put forth by the numerous engineers and geologists who, during recent years, have made a study of the ore deposits in the area under consideration. The first step in a work of this nature would be to record all of the observed facts, and these facts would have to be accepted by those who attempted to formulate a theory of ore deposition. It is with this idea in mind that the writers have described as accurately as possible the actual, observed facts pertaining to the occurrence of the lead-zinc ores in dolomites or dolomitic horizons. By most writers the term "dolomite" is loosely used to designate magnesium-bearing limestones, regardless of the percentage of MgO present. Since no true dolomites exist in the areas to be described, we shall also loosely use the terms dolomite or dolomitic limestone to desig-nate those beds having a magnesia content of 5 per cent MgO or more. For a number of years the writers have been impressed with the fact that in areas where dolomite beds occur a large percentage of the lead ore is found in these beds, in spite of the fact that such beds may be overlain or underlain by pure limestone, which one would assume to be just as favorable for replacement as the dolomite, if not more so on account of its being more soluble in acid solutions than the dolomite. It is true that in some limestone areas, such as the Erupcion-Ahumada districts, Chihuahua, and Providencia, Zacatecas, where no dolomite beds have been found, large tonnages of lead ores have been mined. We venture to predict, however, that had there been dolomitic beds in these areas, the

Jan 1, 1932

By J. E. Lawver, W. D. Carrier

During the past 20 years, millions of dollars in research effort have been spent to improve methods of phosphate clay dewatering and disposal. Although to date no proven large-scale system has been developed that will result in ultimate below ground storage without the use of at least temporary dams, considerable progress has been made and a variety of techniques are being tested, some on a large scale. This paper summarizes the use of mathematical and centrifuge (physical) models that can analyze and evaluate various systems for the consolidation of phosphatic clays. These provide a powerful tool for engineers responsible for land management and mining waste disposal.

Jan 1, 1985

By N. A. Gjostein

The self-diffusion coefficient D, for a surface near the (100) plane in copper was determined by means of the Mullins theory of thermal grooving, and was found to obey the Arrhenius relationship, and Do = 6.5 x 10' sq cm per sec. Suppression of surface diffusion by chemisorbed impurities encounters difliculties as a satisfactory explanation for the large Q, and Do. Instead, a model is presented which indicates that Q,, as determined by a mass-transport technique, may involve both the energy needed to form an adsorbed atom from a ledge in the surface as well as that for the movement of the adsorbed atom.; LITERATURE reviews1-3 indicate that the mechanism of self-diffusion on metal surfaces is not clearly understood. The lack of experimental data on the temperature variation of the surface self-diffusion coefficient DJ has contributed greatly to this situation. Radioactive tracer techniques4-rn have been used to measure Ds, but for many years only Nicker-son and Parker8 had determined (for polycrystalline silver) an activation energy B, and a frequency factor Do for the surface self-diffusion process. Even in this case, a mechanism could not be clearly inferred because it was suspeted7 that a contribution from volume diffusion was not taken into account by the investigators. Some later work by Li and parkere on polycrystalline gold, in which they obtained essentially the same results as for silver and in which volume diffusion could be accounted for, seems to invalidate this criticism. In 1957, Mullins10'11 developed the theory for the thermal grooving process. This advance has opened a new and promising technique for measuring the surface self-diffusion coefficient Ds. Recognizing that a thermal groove may form by several different mass transport processes, Mullins first consideredlo the cases where a) the groove forms by evaporation and condensation or b) by diffusion along the groove surface, in either case, in a system where a metal surface is in contact with only its dilute vapor phase. In a later paper," he extended the treatment to cases where the groove forms by volume diffusion into c) the solid phase or d) by mass transport through a passive gaseous phase at 1 atm pressure. The time dependence of the groove dimensions and the shape of the groove profiles predicted by Mullins' treat-

Jan 1, 1962

By D. A. Belforti, M. P. Lepie

Spectroscopically pure copper was melted on sapphire plaques in a zydrogen atmosphere. The surface tension of the liquid metal was determined using the sessile drop technique. Measurements were made by direct observation with the aid of a specially const,mcted telescope. The value obtained, 1268 dynes per cm, is compared to that found in the literature. THERE is at this time considerable interest in the use of ceramics for vacuum tubes. The crystalline material is superior to the more conventional glass in mechanical strength, chemical inertness, dielectric properties, ability to withstand high temperatures, and so forth. However, ceramics are much more difficult to seal hermetically with metals than are the glasses. For this reason an investigation was undertaken to determine the wetting and adhesion of metals to ceramics. The sessile drop technique offers a convenient means at elevated temperatures for measuring liquid surface tension, wetting angle, density, spread- ing coefficient, and work of adhesion. Thus, from the contour of a drop of liquid at rest on a solid surface one can obtain a quantitative evaluation of the degree to which the two substances will bond. To this end a special apparatus was constructed so that various molten metals could be observed. Standardization of the apparatus was done initially by measuring the surface tension of copper since this is well documented in the metallurgy literature. Although there are many methods available for the measurement of surface energy,'+ the sessile drop technique has been used most extensively for molten metals and ceramics.5"' Fig. 1 illustrates the dimensions to be measured. From these values, the surface tension of the liquid can be obtained using the Bashforth and bdams' equation and tables.

Jan 1, 1963

By E. P. Jennings

(Read at the Amenia Meeting, October, 1877.) THE abundance and value of the tellurium minerals of Colorado is well known, but, as yet, few analyses have been made of them, and I offer these as a small contribution to the chemistry of these valuable ores. 1. Native Tellurium.-The specimens from which the analyses of this mineral were made are from the "John Jay" Mine, Boulder County, Colorado, where it occurs in quite large masses, though mixed with more or less silica and iron pyrites. It is usually a fine¬grained, tin-white mineral, but sometimes occurs in distorted, hexag¬onal prisms in cavities in the quartz. Before the blowpipe it gives the reactions for tellurium, sulphur and iron; by cupellation, it yields a small amount of gold. An analysis of a coarsely crystallized speci¬men gave the following results

Jan 1, 1878

[Trans. No.Place Date Vol. Page 1. Wilkes-Barre, Pa.* .... May, '71.. 1 8 2. Bethlehem Pa Aug., '71.. 1 10 3. Troy N. 'l Nov., '71.. 1 13 4. Philadelphia, Pa Feb., '72.. 1 '17 5. New York, N. Y.• ....May, '72 1 20 6. Pittsburgh, Pa Oct., '72.. 1 25 7. Boston, Mass Feb., '73.. 1 28 8. Philadelphia, Pa.' May, '73.. 2 3 9. Easton, Pa Oct., '73.. 2 7 10. New York, N. Y Feb.. '74 2 11 11. St. Louis, Mo' May, '74.. 3 3 12. Hazleton, Pa Oct., '74.. 8 8 13. New Haven, Conn....Feb., '75.. 8 15 14. Dover. N. J.' Mav. '75.. 43] [ ]

Jan 1, 1925

By S. F. Reiter, W. R. Hibbard

A survey of the effect of heat treatment on the room temperature hardness of Fe-Mo alloys has been made. Constant strain rate tensile tests were performed between room temperature and 1800°F. These data were analyzed to determine the effect of temperature and composition on the strain hardening coefficient and strain rate sensitivity. Constant load creep-rupture tests were made on these alloys and the results related to composition and structure. A relation between the high temperature strength of the precipitation hardened alloys and the volume of precipitate has been observed. IN view of the extensive use of ferritic materials at elevated temperatures, it is surprising to note the limited amount of information relating the variables of plastic deformation, i.e., composition, structure, temperature, stress, strain, and strain rate. Hollomon and Lubahn' showed how the several variables of plastic flow might be treated analytically. No data were available on carbon-free iron and its alloys in a form suitable for this analysis. Several German investigations2-" constitute most of the experimental work relating high temperature properties to the constitution of these types of materials. In order to obtain new data, the iron-rich alloys of the Fe-Mo system were selected for detailed investigation for the following reasons: 1—Some of the important effects of molybdenum on the mechanical properties of iron have already been studied.' , 821 2—By suitable heat treatment of selected alloys, it is possible to study strengthening effects of four types: AT -a transformation, B—substitutional, C—precipitation, and D—dispersion of hard inter-metallic compound. Materials and Treatment Four-pound ingots were vacuum cast, employing the same melting schedule previously used.? The raw materials were electrolytic iron and lamp-grade molybdenum. The ingots were forged to l/z in. sq. rod and one portion swaged to 0.350 in. diam rod for the production of 1 15/16 in. long button-head specimens. The button-head specimen blanks were solution treated for 16 hr at 2100°F in hydrogen of —70°C dewpoint and then water quenched. They were subsequently plunge ground to the standard 0.160 in. diam test bar. Micrographs of the solution treated alloys are given in Figs. la through Id. The higher molybdenum alloys contained large equiaxed ferrite crystals similar to those in Fig. Id. A portion of the % in. rod was hot rolled to 0.100 in., sandblasted, and cold rolled to 0.020 in. Strip tensile specimens having a 0.020x0.200 in. cross-section and a 2.25 in. gage length were machined from the sheet. The alloys containing molybdenum were subsequently annealed 1 hr at 1560°F. The iron strip was annealed 4 hr at 1300°F in wet hydrogen. The resultant structures are shown in Fig. 2a through h. The ASTM grain sizes were 1 to 3 as solution heat treated or 3 to 4 as annealed. The chemical analyses of the alloys are given in Table I. Carbon contents were obtained after the heat treatments in hydrogen. Alloy 15.9 pct Mo was tested as a cast alloy.'

Jan 1, 1956

By Roshan B. Bhappu, Raul A. Deju

A method is proposed by which the chemical reactions between water and a silicate bed can be related to equations of flow. First the reaction mechanism is studied both theoretically and experimentally. Once the reaction mechanism is established, the equations of flow are solved, and a solution (under physically reasonable side conditions) is obtained. Experiments to substantiate the solution are also presented. The knowledge of surface reactions at the water-solid interface is of critical importance in extractive metallurgy. This is especially true in regard to the froth-flotation process of mineral concentration and all phases of hydro metallurgical recovery of metals. Similarly, the problem of ground-water contamination is one of growing concern, not only because of the increasing demands on our sources of supply but also because of the increasing necessity to find vehicles of waste disposal. The hydrochemistry of waste waters must be understood to exploit and develop such resources properly. To understand these problems, it is necessary to obtain a better insight into the reactions that take place between water and a solid packed bed. To do this, we will develop here in a theoretical model that predicts the fate of a chemical species in solution as it reacts with a silicate bed through which the liquid percolates. The treatment will be one-dimensional in nature and will not include dispersion. Experiments will also be presented to substantiate the theoretical model, using the silicate minerals listed in Table 1. This paper is preliminary in nature and is part of a larger study of the surface chemistry of the silicate-water interface. Mechanism of Surface Reactions In a previous paper,' the authors discussed the properties of various silicate minerals from a mineralogical standpoint. Now efforts will be made to study the reactions that occur when these minerals are put in contact with water. The reactions occur almost entirely in the surface layer of the mineralsa and are termed sorp-tion reactions. In this study sorption denotes the composite of all physical adsorption and chemical adsorption occurring between the silicate surface and the water in contact with it. A model of sorption as seen from a chemical-bond standpoint is presented below. On the basis of this model, the surface reactions between deionized water and a silicate mineral can be studied. Sorption Model: It is known that as the oxygen-silicon ratio increases from quartz to the olivines, a greater percentage of the oxygen bonding power is available for bonding to cations other than silicon. Hence, with an increasing oxygen-silicon ratio, the oxygen-to-metal bonding increases. Upon the fracturing of a silicate-mineral crystal, the oxygen-metal bond breaks more easily than the stronger oxygen-silicon bond, resulting in a negatively charged surface. Then, if the mineral is immersed in a liquid containing hydrogen ions, the negatively charged surface should tend to be neutralized by hydrogen ions from solution, resulting in a change of the solution pH. Thus, an increase in the degree of sorption of hydrogen ions must occur as the oxygen-silicon ratio in the crystal structure increases. Also in a previous paper,' the authors found that for a given silicate mineral the change of pH with time is given by

Jan 1, 1971

By Newell Hamilton

SOME years ago, in the manufacture of seamless tubing from an alloy steel containing 0.07 per cent maximum carbon, 18 per cent chromium and 8 per cent nickel, at the plant of The Babcock & Wilcox Tube Co., a peculiar type of piercing defect was noticed. This defect was definitely associated with certain heats of the alloy and was independent of any of the variables of mill operation and billet-heating condition. A thorough analysis of the defective material yielded but one clue to the reason for its abnormal behavior in piercing and that was its oxygen content as determined by the vacuum fusion method. The oxygen content of the defective 18-8 alloy was found to be from two to three times that of the material that had pierced satisfactorily, and this incited an active interest in the vacuum fusion method for the analysis of alloy steels. After a critical survey of the literature on this subject, and considerable experimentation, an apparatus and technique were evolved that gave a fairly rapid, simple and reliable method of analysis. Samples selected from six years of tube production of 18-8 and other corrosion-resistant alloys were analyzed by this method. This paper describes the procedure and gives a correlation of the oxygen, hydrogen and nitrogen contents of a number of alloy steel samples repre-sentative of good and bad tube-piercing quality.

Jan 1, 1934

By B. F. Oliver, C. W. Haworth

Pure tin and Sn-0.5pct Pb ingots have been frozen unidirectionally from the base. For quiescent melts that were initially undercooled, a transition from lower eqlciaxed structure to an upper columnar structure is found in the alloy ingots. Columnar to equi-axed back to columnar transitions are observed in superheated alloy ingots, but no such equiaxed band is observed impure tin. The reproducible equiaxed band is associated with a thermal undercooling followed by a recalescence. This undercooling is <5"C, whereas the critical (maximum obtainable) under-cooling for both the pure tin and the alloys used is -20°C. A similar undercooling is observed at the same position in the pure tin ingots, although in this case no clear transition in structure can be seen. The structure of the pure tin ingots is either entirely columnar or mixed columnar-equiaxed. A consideration of the detailed thermal history of the ingots indicates that the ingot macrostructures are determined by the occurrence of a local therlnal undercooling in conjunction with nuclei multiplication and transport mechanisrris. GENERALLY it is found that a pure metal ingot solidifies so as to produce an entirely columnar structure. Frequently an alloy ingot is found to have a columnar outer zone and an equiaxed central portion. Early systematic work to examine the factors controlling the formation of the equiaxed structure was reported by Northcott&apos; who showed that, for copper alloys frozen unidirectionally with a given ingot practice, the alloying element influenced the length of columnar crystals and the extent of the equiaxed structure. Northcott showed that alloys with a wider freezing range more readily produced the equiaxed structure. The nucleation process can be important in producing equiaxed structures; frequently an alloy which readily solidifies with an entirely columnar structure will produce an entirely equiaxed structure when a nucleating agent is added to the melt.&apos; The formation of the equiaxed structure was attributed by Winegard and chalmers3 to the presence of constitutional supercooling; that is, a region of liquid in front of the growing solid could have a temperature below its equilibrium liquidus temperature. Thus, with a small enough temperature gradient in the liquid, it was suggested that the presence of constitutional supercooling may be sufficient to bring about the nuclea-tion necessary for the formation of an equiaxed structure. Although this explanation is plausible, and may be relevant in many ingots, Walker has described an experiment&apos; for which constitutional supercooling seems to be an unlikely cause of nucleation. A Ni-20 pct Cu alloy, repeatedly undercooled more than 50"C, was crystallized and found to show the typical colum-nar-equiaxed structure. The separation between the liquidus and the solidus for the alloy is 40°C. Thus, in this experiment the nucleation required for the formation of the equiaxed structure must have come about in some other way than by the nucleation catalysis constitutional supercooling hypothesis. Chalmers has suggested more recently5 that nuclei (in a typical ingot) are present immediately after pouring and are prevented from redissolving by the constitutional supercooling effect. More recently Uhlman, Seward, Jackson, and ~unt&apos; have shown direct evidence using ice and organic materials that freeze dendritically that the "remelt mechanism" may be an extremely effective crystal multiplication process during the freezing of ingots under conditions involving dendritic growth. JSlia" experimentally demonstrated the detachment of dendrite arms. chernov14 has analyzed the dendrite arm detachment process as a coarsening phenomena driven by the minimization of interphase area. Katta-mis and ~lemings" working with undercooled steel melts give evidence supporting this mechanism. Mechanisms of dendrite arm detachment such as those assisted by convection are believed to be the origin of the macrostructures obtained in this study. This study makes no attempt to distinguish the relative contributions of these mechanisms. The object of the present work was to obtain accurate temperature measurements during the solidification of an ingot and to correlate these measurements with the formation of equiaxed grains in the resulting ingot structures. Similar previous work is very limited. The measurements carried out by Northcott are neither sufficiently extensive nor sufficiently accurate for any interpretation. Plaskett and winegard7 carried out experiments on A1-Mg alloys in which they observed values of the temperature gradient, G, in the liquid and rate of freezing, R (for a given alloy solute content Co), at the transition from a columnar to an equiaxed structure. They reported that equiaxed crystals were produced at values of G/G approximately proportional to the solidus composition. Similar experiments using Pb-Sn alloys carried out by £111011" showed a linear relation between G/R and the solidus composition. However, the thermocouples were in the mold wall rather than in the melt and, in one case, ingot surfaces were examined. There is ambiguity in the meaning of the values of G and R measured in all these experiments. APPARATUS AND EXPERIMENTAL PROCEDURE Alloys were prepared by induction melting 99.999 pct Sn and 99.999 pct Pb to form a Sn-0.5 wt pct Pb alloy in air in a graphite crucible and casting into a cylindrical graphite mold 6 in. long, 1 in. in diarn , and with a & in. wall thickness. This mold was mounted on a copper base through which cooling water could be

Jan 1, 1968

By Owen W. Ellis, Telfer E. Norman

The use of cadmium as a base for bearing metals is one of the most interesting recent developments in this field. It has caused a strong demand for cadmium and a marked rise in its price. It appeared to the authors, therefore, that the situation might be relieved for users if acceptable substitutes could be developed. A preliminary investigation has revealed that to some extent mercury may be substituted for cadmium. Whether its use is justified cannot be stated at this time. Most of the authors&apos; work has indicated that the addition of mercury to alloys of cadmium and nickel detracts from their desirable physical properties; but this work has not been extended to cover service tests, which might reveal that the addition of low percentages of mercury to the cadmium-base alloys would improve their performance. The results of tests made by the authors are therefore briefly summarized for this paper. Table 1 gives the proportions of the metals used in preparing the alloys. After preparation of these alloys, th composition was checked by chemical analysis. Particular care taken to ensure that the nickel content did not vary appreciably from 1 per cent.

Jan 1, 1938

By Sandford S. Cole

Manganese compounds occur in many mineral forms widely distributed throughout the crust of the earth. The most important of these commercially are the oxides which are usually found as irregular masses, but in some places (notably U.S.S.R.) occur as extensive beds of varying thickness and purity. The principal sources of ore have been U.S.S.R., Ghana (the Gold Coast of Africa), India, Union of South Africa, Belgian Congo, French Morocco, Cuba, Brazil, and Mexico. New developments of ore are being conducted in Brazil, British Guiana, French Equatorial Africa, and Northern Rhodesia. The production of the United States normally meets less than 10 pct of domestic manganese consumption. Manganese ore (35 pct or more Mn) is used principally by the ferrous metallurgy industry for production of manganese metal, ferromanganese, and other manganese alloys for use in production of steel ingots and castings. Some manganese is used in the nonferrous industry as an alloying element and cleanser in aluminum alloys, aluminum bronze, constantan, manganese bronze, Monel, Everdur, nickel-chromium resistance alloys, and nickel-silver. The metallurgical uses consume about 97 pct of the total manganese ore requirements of the United States. The balance goes principally for the manufacture of dry cells and for chemicals, with limited amounts for ceramic products, plastics, welding rods and varnish. The Materials Survey on Manganese, compiled in 1952 for Materials Office National Security Resources Board by the Bureau of Mines and Geological Survey, provides an excellent review of resources, reserves, specifications, uses, mining, beneficiation, metallurgical processes and deposits, and is worth referring to for greater details. Mineralogy and Geology The more common manganese minerals with typical characteristics are listed in Table 1 in order of importance. [ ]

Jan 1, 1960

By Homer E. Harris, William C. DeSieghardt, William A. Burgess

Under sponsorship of NIOSH, Eastern Associated Coal Corp., with the Harvard School of Public Health acting as a subcontractor, has determined for the first time the effective protection provided to working underground coal miners wearing approved half-mask dust respirators. This was done by conducting 187 man-shifts of in-mine testing in four different coal mines; included in this testing were 37 different test subjects representing 11 different job classifications and 5 different models of respirators. Presently available respirators on average provided significant protection levels to working miners even though on an intermittent use basis. However, "average" protection values were well below those achieved under laboratory conditions. Protection levels varied from man to man in a given work crew and from day to day for a given man. In addition, some of the factors affecting use and effectiveness of presently used respirators are discussed, as are areas in which improvements are needed, and the need to consider these improvements in context of a systems approach.

Jan 1, 1975

By P. de Vitry, Willis P. Mould

The wire saw is a tool not less than 60 years old, probably nearer 100 years old. It was developed in Europe and is reputed to have originated in Belgium. Frombold is said to be the original patentee. Wire sawing equipment, as indicated in Fig. I, is very simple. It consists of a three-strand wire cable, usually pis or 1/4 in. in diameter, or a single flat ribbon of medium hard, tough, alloy steel twisted into a helix of those diameters, made to form an endless belt of any length up to several thousand feet. The wire is guided into the cut by sheaves mounted in slides on steel columns situated close to either end of the cut. The feed motion usually is controlled either by gravity or by hand-operated feed screws. The steel columns or "standards" range from 15 to 30 ft. in length. At the top is a swiveled arm supporting a sheave similar to the traveling sheave below. Immediately under the swivel-mounted sheave is a guy plate or collar with shackles attaching four chain or wire-rope guys with suitable tightening devices, or with two guys and two jack legs for supporting the standard vertically or at any desired anale. The usual drive is by a 10-hp. motor through a gear reducer, on which are Insti- two grooved sheaves, One of which is keyed and the other free running On the shaft. Tension is provided by a car running on a track in line with the driving sheave

Jan 1, 1948

By Claudio Gutierrez

It has been claimed (Eadington and Rosser, 1969) that when freshly precipitated lead sulfide is in contact with oxygen-containing water, there is an "induction period" of at least a few hours during which no detectable oxidation of the lead sulfide takes place This effect would be of the utmost importance for the adsorption of xanthate on galena in flotation mills. It was tried here to reproduce the results obtained in (Eadington and Rosser, 1969), but no "induction period" was found. Besides, reasons are given to prove that the oxidation mechanism proposed by Eadington and Prosser (1969) is not realistic.

Jan 1, 1982