Search Documents

By Homer N. Mead

This report develops equations for decline curve analysis based upon the premise that the rate of change of the reciprocal of decline for succeeding time intervals is constant when the reservoir is produced under a fixed set of conditions. A method is shown for predicting maximum production rate against cumulative production for any reservoir. A method is also presented for predicting future production rate by an analysis of past production performance after decline has been esrahlished. INTRODUCTION No significant contribution to the analysis of decline curves by the loss-ratio method has been made since J. J. Arps paper1. The concept of loss-ratio that was developed by Arps and his contemporaries has been redefined in another way and the concept of instantaneous loss-ratio at time zero has been added. In the mathematical developmerit by Arps, production rate was related as a continuous function with time and his equatlons were developed on that basis. In this paper, production is considered to be a series of segments for equal time intervals and equations have been developed based upon these finite differences. It is realized that decline curve analysis is not the answer to all predictions of reservoir behavior. However, as production must decline from an initial maximum rate to zero in any reservoir, if such decline can be expressed as an infinite series, this series should accurately predict production. Decline curve analysis should be considered a valuable tool that may be used in conjunction with predictions of future recoveries by other methods. Various uses of the decline curve method will be discussed in this paper. Equations predicting production rate at any time and cumulative production by exponential and hyperbolic decline will be developed. Characteristic values of b related to various types of drive will be discussed. After that a hypothetical reservoir will be studied and ultimate recovery by natural depletion and pressure maintenance compared, then actual field examples will be shown and discussed. The rate-cumulative curve introduced by H. N. Marshs in 1928 is an important one for use in estimating future production rate and ultimate recovery. This graphical method is the one that is used in conjunction with the equations to be developed for predicting production behavior. EXPONENTIAL DECLINE In exponential decline each succeeding production rate per unit of time is a constant percentage of the production rate just before it. Since (1 — r) is the common ratio, where r is the constant decline rate, this condition may be expressed as a geometrical progression; thus Pn = P (1 - r)n-1 . ......(1) Where r is less than unity, r Since P1 (1 - r)n = Pn+1 P1 - Pn+1 C =P1-Pn+1/r........(2) LOSS-RATIO In this paper the calculation for loss-ratio has been changed from the method presented by Johnson and Bollens2. The first loss-ratio to be calculated is a,; it is the initial production per unit of time after decline has set in divided by the difference between the initial and the second production rate. This loss-ratio is for the first time interval. After b (which is the constant change

Jan 1, 1957

By H. Majima, E. Peters

The oxidation rates of pyrite, pyrrhotite, chalcopy-rite, chalcocite, covellite, bortzite, galem, sphalerite, and stibnite have beet2 carefully compared at 120 oC, using aqueous phosphate solutions buffered at pH 2.7, 7.1, and 11.2 as zvell as in 1.0 M NaOH and in am~onia-containing solutions. Under conditions of these studies, variations in rates of more than a factor of two per unit of mineral surface area were not observed for different minerals in phosphate buffered solutions, except that pyrrhotite showed unusually rapid oxidation rates In acid solutions, and stibnite showed very rapid oxidation rates in basic solutions. In caustic solutions, oxidation vates varied considerably, the most rapid being for pyrite and the slowest for sphalerite. In the presence of ammonia, only copper minerals showed more vapid oxidation rates in neutral solutions. Oxidation rates were measured on the basis of oxygen-consunzption rates per unit surface area of exposed mineral, using equivalent surface areas, mineral mesh sizes, pulp densities, agitation, and oxygen pressure. OXIDIZING pressure leaching of sulfide minerals has been a commercial method of treating concentrates of nickel, cobalt, and copper for over a decade, and recently the treatment of lead and zinc concentrates,' and even the recovery of sulfur from pyrrhotite by such processes, have been shown to be technically feasible.' Furthermore, the leaching of uranium ores by solutions acidified through the oxidation of pyrite and other sulfides present in the ore is commercially practicable.3 5 The mechanisms by which sulfide minerals oxidize in aqueous environments are not yet understood. However, certain generalities can be made for systems containing no unusual reagents, in which oxygen is the oxidizing agent. In acid solutions the oxidation of many sulfide minerals leads to the formation of elemental sulfur.8'7 The attack of some sulfides, notably galena (PbS), sphalerite (ZnS), and pyrrhotite (FeS), at temperatures below about 110°C leads to an almost quantitative conversion of the sulfide mineral to elemental sulfur according to the equation: On the other hand pyrite (FeS2) and copper minerals do not yield elemental sulfur quantitatively. Not more than 50 pct of the sulfur in pyrite is converted to the elemental form in acid oxidation, and this percentage is lowered by higher temperatures and possibly higher oxygen pressures.8'9 Copper minerals sometimes yield elemental sulfurlo'" but, since sulfur can reduce cupric ions with the precipitation of CuS or Cu2S, it is not likely that elemental sulfur is obtained in good yield. In acid solutions sulfur that is not converted to the elemental form always appears as sulfate salts or sulfuric acid. Sulfide minerals that yield elemental sulfur nearly quantitatively on oxidation in acid solutions tend to generate H2S when the conditions are not oxidizing. However, although it has been suggested that H2S is an essential intermediate in the mechanism of oxidation," this is doubtful because it is oxidized very slowly by oxygen. In basic solutions elemental sulfur is never formed, as predicted by thermodynamical considerations, summarized in the form of a potential-pH diagram in Fig. 1. However in neutral and basic solutions, unstable forms of sulfur not shown in the diagram appear during oxidation, notably thiosulfate (SOT-) and polythi-onates (S,O;-, x = 2 to 6).l3,l4 On prolonged oxidation only hexavalent sulfur as sulfate (SOi-) or sulfamate (NHzSO;) is found to remain, the latter appearing only in the presence of ammonia. The oxidation kinetics for thiosulfate by oxygen are the subject of a separate paper,'5 and were studied on the presumption that thiosulfate may, in fact, be a primary oxidation product for sulfide minerals, at least in neutral and basic solutions. A survey of the literature indicated that comparative oxidation rates for different sulfide minerals were needed to establish the role of the mineral structure and its thermodynamic properties on the oxidation rates and mechanisms.

Jan 1, 1967

By L. H. Hart

Because of a widely recognized association between breccia pipes of one form or another and many important copper deposits, conditions under which breccia pipes develop have been of great scientific interest for many years. Since these phenomena first attracted attention, many theories have been advanced to explain their origin. This is not unexpected, since it is likely that they have been formed by and under a wide range of conditions. Moreover, the entire subject is confused by the fact that the term breccia pipe is applied to a wide variety of occurrences. To discuss any part of the subject intelligently, therefore, it is necessary to start with definitions of the terms used. In their discussion of the Toquepala deposit, Richard and Courtright have carefully defined the terms they have used in their presentation of a very logical geo- logical history of Toquepala breccias. This is a real contribution, as there is no reference in the literature known to the writer where the history of a series of breccia pipe epochs, confined essentially within one channelway, may be read with the degree of certainty that appears to be possible at Toquepala.

Jan 6, 1958

By James T. Gow, Oscar E. Harder, Anton de S. Brasunas

This paper deals with the results obtained and the techniques employed in determining: 1. Liquidus and solidus temperatures of the HH and HT type heat-resistant alloys. 2. The relation of true temperatures (thermocouple) to apparent temperatures (optical pyrometer) for the molten HH and HT type alloys. This work was the outgrowth of needing to know something definite about these temperatures in order to study the effect of pouring temperatures, shake-out times, and heat-treatments on the properties of some heat-resistant alloys. The information developed is thought to be of interest to industry for guidance in foundry practices and the industrial heat applications of the alloys. This paper is based upon work that has been done for the Alloy Casting Institute at Battellc Memorial Institute. Liquidus and Solidus Temperatures of HH and HT Type Alloys Experimenta1 Procedures Temperature-time curves were obtained during the cooling and solidification of several HH and HT type alloys. The metal was melted in an Ajax high-frequency, induction furnace and poured into a core-sand mold for cooling. The temperature measurements were obtained by means of a platinum, platinum-rhodium thermocouple contained within a fused silica sheath, which was extended through the side wall of the dry core-sand mold to a point at about the center of the mold cavity, which was 3 in. in diameter by 5 in. deep. The cold junction of the thermocouple was kept in an ice bottle, and the temperature was recorded automatically on a direct-reading potentiometer recorder. Through a switching arrangement, the temperature recorded was checked occasionally with a portable Leeds and North-rup potentiometer indicator. Less than a 5°F. variation in the two instruments was always found. This is within the limit of accuracy of readings. The thermocouple used was checked for accuracy against a standard couple, both before use on this work and after completion of the work, by the instrument laboratory. Temperature-time Cooling Curves Fig. I is an enlarged reproduction of a part of one of the cooling curves over the temperature range of 2600' to 2200°F. for an alloy of the HT type with 0.45 per cent carbon, 16 per cent chromium, and 36 per cent nickel. This is a typically shaped cooling curve as obtained for the alloys. It will be noted that two temperatures "re shown on Fig. I for the liquidus temperature. It is thought likely that the higher temperature, A, at the point at

Jan 1, 1945

By Gordon I. Gould

The treatment of quicksilver ores to extract the metal, for centuries one of the fundamentally simpler metallurgical operations, has undergone few if any material changes during the past iew decades other than improvement and change of type of equipment used. Of almost universal application and as the seldom deviated from process, the roasting method is still considered superior to chemical metallurgy. Likewise, roasting of the crude ore without previous beneficiation continues to be standard practice, although some successful operations have employed concentration prior to roasting. The roasting process has been carried out in a variety of equipment, devised for different tonnage capacities, to treat "special" ores, and to satisfy an inventive notion of the particular builder, but during the past 25 years there has been one outstanding change in roasting equipment. This change, though neither originating in nor confined to the United States, has probably been developed and applied to a far greater extent in this country than in any other mercury-producing country of the world. The change from manually or gravity operated furnaces, mostly huge brickwork affairs justified largely by simplicity, lack of power and mechanical requirements, and occasionally by excellent metallurgical results, to mechanical furnaces, began actively during World War I under the stress of requirements for in- creased production, a shortage of labor, 2nd other factors to be brought out later. During the twenties the change to mechanical furnaces became nearly complete at American mines with the development of several types, the rotary furnace predominating. During the thirties, and the period of low prices in the early part of this period, few changes were made other than mechanical improvements and an almost complete acceptance of two types: the rotary furnace and the hearth or Wedge furnace. These two types have been developed to a high degree of metallurgical efficiency, have proved to be mechanically simple and have far greater flexibility and lower operating costs than pre-World War I furnaces. Of the two types the rotary is the more popular, about 30 rotaries having been in operation in the United States in 1943 as compared with about six hearth-type furnaces. The units of smaller capacity for roasting mercury ores have almost without exception been indirectly fired, such distinction being commonly accepted as the difference between retorts and furnaces, which are fired directly. The difference between indirect and direct firing obviously permits of quite different conditions surrounding the ore being roasted in relation to the chemical reaction to take place. In the indirect-fired unit the ore is contained within the body of the retort in a stagnant if not completely oxygen-impoverished atmosphere. In the direct-fired furnace the ore is in contact with the gases of combustion, which may easily (if not too easily) be supplied with an excess of

Jan 1, 1944

By H. P. Allen

THE Achotla mill of the Cia. Minera de Pe[n]oles is of special interest in that it is one of the few still employing the chloridization process. The ore milled comes from the Suriana mine and consists of both oxide and sulphide, from neither of which can the gold or silver be extracted by a simple cyanide treatment. The mill was built in 1927, after several years of study in the development of the process1, and operated from December of that year until October 1930. Operations were resumed in February 1935, and have been continuous since, treating approximately 5000 tons per month, while the mine is getting up to full tonnage of 6500 tons per month. Transportation Of Supplies The property is in Guerrero, Mexico, some 175 km. by airline southwest of Mexico City. The mill site is at Temisco (Fig. I), 8 km. from the Balsas River and 4.8 km. by aerial tram from the mine. At Temisco are the general office, shops, warehouses and laboratory serving both mine and mill. Here sufficient water is available either from a small creek running through the property or from the Balsas River, also convenient and ample storage space for the tailings. With the exception of the mine timber and a few native building materials which may be obtained locally, all supplies for both mine and mill are brought down the Balsas River from Balsas, the terminal of a Mexican National Railway line out of Mexico City. The method of transportation on the river is interesting. Rapids with very fast water are numerous, prohibiting the use of mechanically propelled boats. Those used resemble large, flat-bottomed rowboats some 22 ft. long by 8 ft. wide (Fig. 2). They are manned by two oarsmen sitting in the bow, each handling one large oar, and usually another man in the stern who, with his oar, assists in steering the boat, especially when the rapids are run. From 3 to 7 tons of freight are carried on each boat, depending upon the stage of the water, which governs also the time

Jan 1, 1937

UP TO and including 1931, the twelve mines that were treated in THE PORPHYRY COPPERS had produced 17.4 billion pounds of copper worth $2,820,000,000. With a little help from six others (three of them did not start output until 1954) that record had been increased at the end of 1955 to 60.5 billion pounds worth $10,440,000,000. Today, ten billion dollars is not as impressive as it once was; but it still represents a lot of value. It must be remembered that this is newly-created wealth, produced entirely from material considered worthless when the Porphyry era started about fifty years ago. At that time "rock" that contained less than forty pounds of copper per ton was regarded by competent mining engineers as value- less. It was not "ore" in the economic sense. Today, ore is being successfully exploited that contains less than twelve pounds of copper per ton. Also, in Peru, a typical Porphyry operation is being launched by a partnership of four United States mining companies that will involve an initial capital investment of $200,000,000 for mine development, plant construction, and the provision of related facilities. Of this project more will be said at the end of the chapter. The point I want to make now is twofold: (1) that phenomenal progress has been made in Porphyry engineering and technology; and (2) that exploitation of an important Porphyry copper deposit has become an industrial enterprise of truly great magnitude. Much had been accomplished by 1931; but that progress has been dwarfed by the achievements of the past 25 years- a fact that, in the nature of things, is as it should be.

Jan 1, 1957

By Robert B. Sosman

The chance that a Howe Memorial Lecturer will be able to refer back to a personal contact with the distinguished metallurgist for whom this lectureship is named grows steadily I I did not have the pleasure of his personal acquaintance, but I did receive from him in 1916, quite unexpectedly, a letter commenting On a paper that I had recently published27 On "Types of Prismatic Structure in Igneous Rocks." The paper was written for geologists and petrologists, but it had an application, naturally, to the crystallization of iron and steel in a mold. The letter impressed me at the time, and still does, with the breadth of of Howe's interests and his perseverance in keeping up with the progress of any branch of knowledge that had metallurgical connotations. Scope of the Lecture During several years preceding the date mentioned I had worked in collaboration with Arthur L. Day and E. T. Allen8 at the Geophysical Laboratory, Carnegie Institution of Washington, on the temperature scale as defined by the nitrogen thermometer at high temperatures. Later (1928-1947) I had the opportunity of helping to apply this experience to the pyro-metric problems of the steel industry. Because of the range of its temperatures, the multiplicity of the methods used, and the variety of its purposes, pyrometry in the open-hearth process has always offered a fertile field for both research and development. I am therefore devoting an hour to the subject of temperatures in the basic open-hearth furnace, the furnace that makes most of our steel in the united States. I would direct your attention particularly to the choice of the first two words in the title of the Lecture. One sometimes hears or reads of the ((temperature of such-and-such a furnace," as if it were a single, measurable, characteristic quantity. I need hardly emphasize to any one who has ever operated a furnace or a kiln that " temperature of the furnace " is a meaningless phrase. Even if we confine our attention to the space enclosed by the roof, walls, and hearth of an open-hearth furnace, it is doubtful whether any such space has ever been so uniform in temperature that the phrase would have a meaning. In any furnace, there are many different temperatures, capable of being measured at many different places, and actually being measured for several different purposes. These pyrometric purposes, methods, and results, if given in detail, would expand this lecture into a book on the basic open-hearth process. I must therefore confine myself to a statement of the range of temperatures as they have been observed in various parts of the furnace, indicating in a general way why they are measured, and mentioning the methods that are available without attempting to describe these

Jan 1, 1949

By Charles M. Bayer

Reading in the AIME annual reports that certain activities have been financed by the Rocky Mountain Club Fund, less senior members of the Institute may wonder. "What's the Rocky Mountain Club?" Less youthful members will not have to wonder. They will recall the Club as an intriguing, almost fantastic organization, largely of western mining men, that flared across the New York horizon, flamed brilliantly for a little more than two decades, then sputtered out of existence- glorious even in its last flash. It was the only product of its mold, a fabulous group of magnanimous men who unhesitatingly sacrificed a cherished dream for which they had raised millions of dollars so that the money, instead of creating a magnificent club house, could be used instead to save the lives of starving Belgian children in World War I.

Jan 12, 1964

By R. M. Barnes, A. H. Bell

The ideas set forth in this paper are proposed for consideration and discussion as the result of recent study of various plans for control and proration of gas and oil production from Kettleman North Dome oil field. They would be applicable to any oil field during its flush production stage. The problems of development and proration are so Fig. 1.—Ideal Cross-section, Kettleman North Dome Oil Field. intimately connected in Kettleman Hills and in many other flush fields that they have both been covered in this paper. Many are of the opinion that Kettleman North Dome oil field should be considered as containing only one zone to its present total penetrated thickness of nearly 1500 ft., and that the hydrocarbon content of this zone gradually changes from dark and relatively low-gravity oil with relatively low gas-oil ratios on the flanks and plunges to mostly light-colored and high-gravity oil with high gas-oil ratios in the higher structural positions, somewhat according to the idealized section shown in Fig. 1. At least the lower 400 ft. contains dark oil in the higher structural positions.

Jan 1, 1933

By H. H. Smith, G. J. Danek, M. R. Achter

Nickel, Type 316 stainless steel, and copper show decreases in reversed bending fatigue strength with increases in air and oxygen pressure. The leveling off of the log N us log p curve for nickel at 300" and 816°C is discussed in terms of a model in which surface saturation gives rise to a critical pressure. A metallographic study indicated that the effect of environment on crack initiation and growth rates is a function of temperature. It is shown that small amounts of impurities in inert gases may substantially reduce the fatigue strength of nickel. 1n a previous investigation1 of high-temperature bending fatigue in air and in vacuum, reversals in the effect of environment with changes in test conditions were atrributed to a mechanism consisting of two processes acting in competition. One of them, oxidation strengthening, has been demonstrated in a straightforward manner by measuring the rupture strength of a sintered nickel-oxide bond.' The detailed operation of the other process, facilitation of crack propagation by surface absorption of oxygen, is uncertain. Thompson et UZ advanced the possibility that the formation of an oxide layer prevented rewelding of cracks during the compressive part of the cycle, while Wads worth and Hutchings4 further proposed that the reaction of oxygen with atoms at the tip of the crack helped the metal to break there, a possibility which has also been advanced to explain crack formation in creep.5 A difficulty in arriving at a mechanism for this lowering of fatigue strength in air is the inconsistency of some of the data. For example, Wadsworth and Hutchings4 found an approximately linear decrease of log cycles-to-fracture (N) with an increase of log pressure-of-air (p) for copper and aluminum at room temperature, while snowden,' although finding a similar linear dependence for aluminum, observed a stepped curve for lead. Between l0-' and 10"1 torr there is a sharp decrease in the fatigue life of lead with increasing air pressure, but plateaus, signifying no dependence on pressure, are found at higher and lower pressures. If, as discussed elsewhere: these environmental effects arise from the adsorption of gas on crack surfaces, it would be expected that as the pressure is increased a saturation point would be observed, beyond which there is no further effect. To gain further information about the form of the log N vs logp curve, it was decided in the present investigation to repeat this type of measurement at elevated temperature on nickel, copper, and Type 316 stainless steel. An additional object of this program was

Jan 1, 1963

By Pramod C. Thakur

Introduction Methane is contained under pressure within the fractures and adsorbed on the surface of the coal seams and adjacent strata. It is released into the mine atmosphere during mining of the seam creating explosive gas-air mixtures. Large volumes of air, sometimes as high as 20 tons of air for each ton of coal mined, are circulated constantly to dilute and carry away methane from coal mines. Removal of methane from solid coal, wherever high methane emissions occur, has been discussed by Spindler and Poundstone (1960) and Thakur and Davis (1977). Methane control in longwall gobs is much more complicated. As longwall mining progresses, the overburden continually subsides, and the immediate roof caves behind the roof supports. Even the underlying strata heave and open up communication channels feeding gas to the longwall gobs. The pressure of gas in the underlying and overlying strata is usually higher than the ambient air pressure in the mine. Thus the mine workings become natural pressure sinks, into which gas flows from the entire disturbed zone. Winter (1975) defines this zone as the "gas emission space". Depending on the number of gas-bearing zones in the gas emission space and their gas contents, the total methane emission from longwall gobs could vary from a few to more than one hundred cubic meters of gas per ton of mined coal. Hence the ventilation of longwall faces demands a large quantity of air. This ventilation need is further enhanced by high air losses specially on caving faces (with no stowing of the gobs). The old system of longwall ventilation, the 'U' pattern, where all the air was brought down one gate road and exited through the other gate road, loses large quantities of air through gobs giving a high methane concentration at the return end of the face. The 'Y' ventilation pattern where intake air is brought down both head and tail gate roads relieves the situation to some extent but, on most longwalls, some kind of methane control is still needed. With the onset of longwall mining in Europe several decades ago, the initial work on methane control on longwall has naturally been done there. The basic principle of methane control has always been, and still remains, some means of "bypassing methane from the gas emission space without letting it mix with the mine air". In most cases the bypassing mechanism is either a strategically located borehole or a roadway. A successful methane control program depends on the following basic premises: a. Determination of the geometry of the gas emission space and location of gas bearing horizons therein. b. Estimation of the rate of methane influx into the longwall gob. c. A scheme to bypass the gas in the most economic and efficient manner and thus prevent it from entering the mine atmosphere. In successful methane drainage programs a high proportion, usually between 50 and 70 percent, of the total gas emissions in a working district is removed before it can enter the mine airways. Advantages of methane drainage can be summarized as: 1. Generally reduced methane levels in the mine leading to increased safety and productivity. 2. Reduced air requirements and corresponding savings in ventilation horsepower. 3. Faster rate of advance for development headings and economy in the size of headings. 4. Possible use of mine gas as an additional source of fuel. The purpose of this paper is to briefly review the geometry of gas emission space and methane influx therein and discuss more successful European and U.S. longwall gob gas control techniques.

Jan 1, 1981

By G. N. Maniar

G. W. Healy (union Carbide Metals Co.)-The author's paper is a useful contribution to the store of maps of chemical activities of oxides in multi-component slag systems. It is also a good example of the utility of the Gibbs-Schuhmann technique for calculating activities in a system where that of one of the components has been measured. This paper Koh and Caugherty. This plot is reproduced by alor in X-ray Metallography. Because of this nonlinearity, preparation cf suitable standards and/or correction for absorption and enhancement are essential in microanalysis. However, our objection is not the conclusion that Dr. Aaronson has arrived at nor the technique he has used; but only to the foot-note credited to V. Macres. The level of chromium that he was concerned with (less than 3 pet) is so low that the deviation of uncorrected Cr-curve will be negligible. Besides Dr. Aaronson has used chromium intensity from martensite and set it equal the bulk chromium content of the alloy. Using this chromium-intensity as a reference, he has calculated the amount of chromium in the ferrite. This amounts to the same as using an internal standard. Since the chromium content in austenite and ferrite are almost the same, enhancement due to iron in both will be the same and therefore does not need to be corrected. together with the author's recently published one1 on the CaO-FeO-Fezo3 system will be most helpful to others learning to apply Schuhmann's method, which merits a far wider application than it has received to date and should greatly aid our understanding of equilibria between metal and oxide phases. As shown by okcen" its use may even be extended to sections of systems with any number of oxides. I have some questions as to the selection of equilibrium constants made by Dr. Turkdogan. He has chosen one for the formation of Fe2O3 from FeO and oxygen which gives Fea3 activities 50 pct higher

Jan 1, 1963

The war story of the engineer corps at home and in France is told officially for the first time in the advance sheets of the War Department's brief history of American war efforts. Many of these accomplishments have been published before as isolated incidents, but they gave no idea of the extraordinary duties modern warfare has laid upon engineering troops. In the engineering units that reached the other side, there were seven regiments and two battalions of railway construction engineers; five battalions for maintenance of way; two battalions for maintenance of railway equipment; four regiments and one battalion to operate the main American railways in France; three regiments to operate light railways and their repair shops; two regiments to operate the regular railway repair shops; two regiments and six separate battalions on general construction work; two regiments for storing and transporting engineer supplies; a forestry regiment; a light-railway construction regiment; a roadbuilding regiment; a water-supply regiment; a mining regiment; a quarrying regiment; a technical regiment for surveying and sound ranging; three survey and printing battalions; two railway transportation battalions; an electrical and mechanical regiment; several separate companies to operate cranes; a camouflage service; five inland waterway companies, to operate canal boats and the like; five pontoon trains and a pontoon

Jan 6, 1919

By H. F. Ameen, F. M. Hamilton

Results of a laboratory investigation of some sintering variables are presented. The effect on physical properties of mix component variation and rate of cooling of the sinter is illustrated by crush and tumbler test results and data of reducibility tests and microscopic examination of sinters are shown. The results of using solid additions in the mix to improve bed permeability are given.

Jan 12, 1950

The Committee on Nominations is as follows: Pope Yeatman, Chairman, B. B. Thayer, Henry Landes, Robert J. Grant, F. V. Desloge, Albert Burch, C. K. Leith.

Jan 6, 1919

[Alphabetic Section: The letter immediately following a member's name indicates grade: M-member, A-associate, J-junior. The numerals following member's grade indicate year of election. The letter following year of election indicates primary divisional affiliation: A. Mining & Exploration F. Coal B. Minerals Beneficiation G. Petroleum C. Iron and Steel H. Industrial Minerals D. Extractive Metallurgy J. Council of Education E. Institute of Metals K. Council of Economics Geographic Section: An asterisk (*) preceding a member's name indicates availability for consulting work:]

Jan 1, 1961

By F. A. Forward, J. Halpern

A new process for extracting uranium from ores with carbonate solutions is described. Leaching is carried out under oxygen pressure to ensure that all the uranium is converted to the soluble hexavalent state. By this method), alkaline leaching can be used successfully to treat a greater variety of ores, including pitchblende ores, than has been possible in the past. The advantages of carbonate leaching over conventional acid leaching processes are enhanced further by a new method which has been developed for recovering uranium from basic leach solutions. This is achieved by reducing the uranium to the tetravalent state with hydrogen in the presence of a suitable catalyst. A high grade uranium oxide product is precipitated directly from the leach solutions. Vanadium oxide also can be precipitated by this method. The chemistry of the leaching and precipitation reactions are discussed, and laboratory results are presented which illustrate the applicability of the process and describe the variables affecting leaching and precipitation rates, recoveries, and reagent consumption. THE extractive metallurgy of uranium is influenced by a number of special considerations which generally do not arise in connection with the treatment of the more common base metal ores. Perhaps foremost among these is the very low uranium content of most of the ores which are encountered today, usually only a few tenths of one percent. A further difficulty is presented by the fact that the uranium often occurs in such a form that it cannot be concentrated efficiently by gravity or flotation methods. In these and other important respects, there is evident some degree of parallelism between the extractive metallurgy of uranium and that of gold and, as in the latter case, it has generally been found that uranium ores can best be treated directly by selective leaching methods. It is readily evident that this parallel does not extend to the chemical properties of the two metals. Unlike gold, which is easily reduced to metallic form, uranium is highly reactive. It tends to occur as oxides, silicates, or salts. Two ores are of predominant importance as commercial sources of this metal: pitchblende which contains uranium as the oxide, U3O51 and carnotite in which the uranium is present as a complex salt with vanadium, K2O-2UCV3V2O5-3H2O. These ores may vary widely in respect to the nature of their gangue constituents. Some are largely siliceous in composition, while others consist mainly of calcite. Sometimes substantial amounts of pyrite or of organic materials are present and these may lead to specific problems in treating the ore. Further complications may be introduced by the presence of other metal values such as gold, copper, cobalt, or vanadium whose re- covery has to be considered along with that of the uranium, or whose separation from uranium presents particular difficulty. In general, there are two main processes for recovering uranium in common use today.'.2 One of these employs an acid solution such as dilute sulphuric acid to extract the uranium from the ore. A suitable oxidizing agent such as MnO, or NaNO, is sometimes added if the uranium in the ore is in a partially reduced state. The uranium dissolves as a uranyl sulphate salt and can be precipitated subsequently by neutralization or other suitable treatment of the solution. The second process employs an alkaline leaching solution, usually containing sodium carbonate. The uranium, which must be in the hexavalent state, is dissolved as a complex uranyl tricarbonate salt, and then is precipitated either by neutralizing the solution with acid or by adding an excess of sodium hydroxide. The latter method has the advantage of permitting the solutions to be recycled, since the carbonate is not destroyed. This is essential if the process is to be economical, particularly with low grade ores. With each of these processes, there are associated a number of advantages and disadvantages and the choice between using acid or carbonate leaching is generally determined by the nature of the ore to be treated. In the past, more ores appear to have been amenable to acid leaching than to carbonate leaching and the former process correspondingly has found wider application. With most ores, acid leaching has been found to operate fairly efficiently and to yield high recoveries. One of the main disadvantages has been that large amounts of impurities, such as iron and aluminum, sometimes are taken into solution along with the uranium. This may give rise to a high reagent consumption and to difficulties in separating a pure uranium product. Excessive reagent consumption in the acid leach process also may result

Jan 1, 1955

By David C. Jonson, W. Bruce MacKenzie, Arthur A. Bookstrom, Vaughn E. Surface, Neil K. Muncaster, Stewart R. Wallace

In mid-Tertiary time a wet silici-alkalic magma penetrated the Precambrian rocks of what is now the Tenmile Range of Central Colorado and formed the Climax Stock. The stock is a composite one and was intruded in four separate irruptions, each giving rise to a major hydrothermal event. The first three of these produced large stockwork ore bodies that cap and flank the tops of their respective source intrusives; the fourth, and last, yielded almost no commercial mineralization. The ore bodies and their related zones of alteration are circular to ring-shaped in plan and arcuate in section. The different phases of the stock are so positioned with respect to each other that many of the circular and arcuate zones of mineralization and alteration overlap or are juxtaposed. Evidence of a time separation between the different ore bodies is found in certain dikes that were intruded between periods of mineralization and are well mineralized in one ore body but are barren in another. If it is assumed that the parent magma at Climax contained 10 per cent "water," that the "water" contained 0.1 grams per liter of molybdenum, and that the processes of extraction were 100 per cent efficient, then approximately 10 cubic miles of magma would be required for the formation of each ore body. The volume requirements, taken in conjunction with the cross-sectional areas of the different phases of the stock to explored depths, suggest to the authors that each magma chamber was columnar, extended to a depth of thousands of feet, and was connected with a much larger master reservoir. The repetition of similar intrusive, structural, and hydrothermal events, indicates periodic tapping of this reservoir. A regular chemical evolution of the parent magma is suggested by the systematic change in metal ratios and differences in the sites of deposition, relative to the source intrusive, in each of the four separate igneous hydrothermal stages. The preparation of ground was due to changes in magmatic and/ or hydrothermal pressures within the igneous-hydrothermal columns; small, repeated, up and down movements of the rock enclosing the tops of the columns formed the stockwork fractures into which the mineralizers penetrated. The forceful emplacement of each successive phase of the Climax Stock resulted in a slight doming and rotation to the westward of the earlier-formed geologic features. Postore normal displacement along the Mosquito fault is estimated at about 9000 feet. Part of one ore body was cut by the fault and lies at depth below the Paleozoic sedimentary strata on the hanging wall. On the footwall side of the fault, subaerial erosion and glaciation removed a large part of one ore body and uncovered the top of a second.

Jan 1, 1968

By Vincent Gianella

Barite deposits are of widespread occurrence in Nevada but there are few pro-ducing properties; most of the latter are in northern Nevada. The production of the state is small at present-in the neighborhood of 15,000 tons annually-but is steadily increasing. The barite occurs in veins and also as replacement deposits in lime-stone. The bulk of the production has come from the replacement deposits. It is thought that the barite was deposited from rising hot waters similar to-and probably contemporaneous with-those responsible for some of the metallic ores of the state. This paper discusses only the deposits in northern Nevada. THE commercial mining of barite did not begin in Nevada until 1916 but although the production has been small there has been a rapid increase in tonnage during the past several years. Barite is widely distributed in the state and production comes from at least nine of the seventeen counties. Apparently this is not generally known, as only two counties are mentioned in a recent publications dealing with barite. The increase in output is due largely to recently discovered barite deposits in northern Nevada. The principal production has come from the northern portions of Lander and Eureka counties; smaller amounts from Elko County. The discussion in this paper is confined largely to the deposits in these counties. Most of the producing area is tributary to the Western Pacific and Southern Pacific Railroads, whose tracks lie along the Humboldt River. Barite is known from other northern counties but so far the production has been small. The output has come entirely from veins and replacement deposits, the latter largely in sedimentary rocks. In general, the barite from veins is white; that from the replacement deposits usually is dark gray to black, although some is light gray or white. Most of the veins contain sulphides and many barite-bearing veins have been worked for their content of base or precious metals.

Jan 1, 1940