Search Documents

Established as a Division December 15, 1948 Evan Just, Chairman Richard J Lund, Past Chairman Granville S. Borden, Vice-Chairman J K Richardson, Vice-Chairman S H Williston, Vice-Chairman Allan Matthews, Secretary-Treasurer National Security Resources Board 17th and Pennsylvania Ave, N W Washington 25, D C

Jan 1, 1952

By Jean Howard

ThE formation of the (100) [001) texture in 3-1/4 pct Si-Fe strip was first reported by Assmus ef a1.l in 1957. Since then much experimental work has been carried out with a view to establishing the mechanism involved. The papers cited above state that the (100) [001] texture was developed in strip rolled from material melted and cast in vacuum. (The impurity content of the ingot is reported as 0.005 pct.) The present note records that similar results can be obtained in material processed by powder metallurgy. A processing schedule is described.which enables the texture to be formed in strip up to 0.010 in. thick, but there seems no reason why this should not be achieved in thicker strip, provided that large grains are developed after sintering. The materials were prepared from Carbonyl Iron Powder Grade MCP (particle size 5 to 30 p) of the International Nickel Co. (Mond) Ltd. The powder contains about 0.15 pct 0, 0.01 pct C, 0.004 pct N, <0.002 pct S, $0.005 pct Mg and Si, and 0.4 pct Ni— that is, it is substantially free from metallic impurities other than nickel, which is thought to be unimportant in the present work. The silicon powder was 99.9 pct purity, or material of transistor quality (ground in pestle and mortar). The mixed powders (3-1/4 pct Si to 96-3/4 pct Fe) are heated in hydrogen at 350" and 650°C to deoxidize the iron before sintering loose at temperatures between 1350" and 1460°C (depending upon the ultimate thickness of strip required) for up to 24 hr. The object of the high-temperature sinter is to develop a large grain size at this stage. Alternatively, the loose sintering can be done at a lower temperature followed by rolling or pressing and then annealing at temperatures between 1350" and 1460°C. Both methods produce large grains, which remain large throughout the process. The compact is then hot-rolled to approximately 1/8 in. with high-temperature interstage anneals if necessary. This step is taken to avoid intercrystalline cracking which would occur if the material of such large grain size were cold-worked. The bar is then annealed at 1050°C and reduced to its final thickness by approximately 50-pct reductions and 1050°C interstage anneals. Throughout the process the dew point of the hydrogen furnace atmosphere is maintained at about -40°C. Samples were annealed in hydrogen at various temperatures and times. Secondary recrystalliza-tion to (100) [001] was developed on the thinner material (i.e., up to 0.002 in.) by annealing in hydrogen at 1050" to 1200°C with a dew point of - 40°C or in vacuum (10-5 Torr) at 1050°C. With the thicker materials (i.e., up to 0.010 in.) the best results were obtained by annealing in hydrogen at 1200°C with a dew point of - 55°C. Complete secondary recrystal-lization to (100) [001] textures was obtained. Above these temperatures secondary recrystallization to (110) [001] tended to develop. The final annealing of samples was normally carried out with the samples placed between recrystal-lized alumina plates, but some experiments were performed with the samples suspended so that their surfaces were not in contact with anything except hydrogen, and these were equally successful in developing secondary crystals. An approximate determination of the proportion of material (before secondary recrystallization took place) having crystals with the (100) or (110) planes in or near the rolling plane showed that 11 pct of the sample had (100) and 16 pct (110). The method used for the determination is described below. A sample was annealed at a temperature just below the secondary recrystallization temperature and etched to reveal the (100) planes. The approximate area covered by crystals having (100) or (110) in or very near the surface was measured on the screen of a Vickers projection microscope. This was repeated for twenty positions chosen at random and a mean of the results calculated. The main hindrance to developing the secondary crystals in the thicker materials was the difficulty of obtaining a large enough initial primary grain size before secondary recrystallization. This was overcome by increasing the particle size of the silicon powder used. During the course of the work, it had been observed that the larger the grain size after sintering the more likely it was that the material would be successful in developing secondary crystals at a later stage. An experiment was therefore carried out to determine whether the material with the larger grain was more successful in developing secondary crystals due to the large grain produced at the sintering state per se or whether it was due to the greater reduction of silica brought about when the sintering temperature was raised in order to increase the grain size. A comparison was made between two compacts, one of which was made with silicon powder of 60 to 100 mesh, the other with silicon powder which was finer than 200 mesh. F?r this experiment, use was made of a phenomenon previously observed that the larger the particle size of the silicon powder employed in making a compact, the larger is the grain size of the compact. The silicon powder was ground

Jan 1, 1964

By U. W. Lisner, V. J. Hucka

Coal, which was discovered in Utah in 1849, covers about 18% of the total area. Production in 1981 was more than 13 Mt (14 million st). However, some Utah coal mines are quite gassy. If longwall face technology is applied, then release of a large volume of methane may be expected during the mining process. Investigations on methane content have been made by use of an isothermic bubble desorbometer. A desorbable methane content of 0.5 to 16 m3/t (20 to 632 cu ft per st) of coal has been determined.

Jan 1, 1985

By D. J. Carney, E. C. Rudolphy

IT has been demonstrated that inclusion size, distribution, and composition affect the machin-ability of resulphurized steels. Merchant and Zlatinl concluded that large sulphide inclusions aided machining by forming a (lubricating) coating on the tool face. Boulger et al.² and Van Vlack³ noted that the size, distribution, and composition of the inclusions in the steel affected the machinability. Steel specimens containing large globular sulphide inclusions usually exhibited excellent cutting properties, while machinability was adversely affected by the presence of numbers of oxide-type inclusions. Consequently a thorough knowledge of all the factors which affect the inclusions in the final product is desirable. Since almost all the inclusions have their origin in liquid steel, it was necessary to begin a study of inclusions in free-machining steels by studying the inclusions and chemical segregation in the as-cast ingot. Very little information is available on the size, distribution, shape, and composition of inclusions in large, capped, free-machining steel ingots, particularly the B1113 grade. Gregory and Whiteley4 made a general study of the inclusions in a small, high sulphur, free-machining steel ingot. Also, numerous authors have described the solidification and segregation characteristics of the four basic types of steel ingots, namely, rimmed, capped,7 semikilled,7,8 and killed7,9,10 ingots. Most of these studies were made with plain carbon or low alloy, low sulphur steel. It was desirable to study not only the ingot but also the change in size, shape, and number of inclusions on rolling an ingot to a bloom and thence to a billet. This procedure was followed and it is hoped that this study may serve the dual purpose of adding to the general knowledge of ingot solidification as well as contributing to the knowledge of the size, shape, distribution, and composition of inclusions from the ingot to the billet in a high sulphur, free-machining steel. Procedure A 12.000-lb 23x35x75 in. slab ingot of the B1113 grade was cast, sectioned, and studied both macro-scopically and microscopically. An adjacent ingot from the same heat and of the same size was rolled to a 77/8x77/8 in. bloom and thence to a 21/2x21/2 in. billet. These various bloom and billet sections were also sectioned and studied macroscopically and microscopically. Sectioning the Ingot: The ingot herein described was obtained from the United States Steel Corp.&apos;s South Works Bessemer Blow No. 0193, a B1113 mechanically capped heat. The 23x35 in. ingot (No. 2) was teemed according to normal procedures and after stripping and transportation to the rolling mill was not placed in the soaking pit but allowed to air cool in an upright position. When completely solidified, the ingot was cut into sections by means of a powder scarfing torch and further sectioned by saw cutting as indicated in Fig. 1. Cut No. 2 (1x10x12 in.) from sections A through H was cleaned thoroughly, macroetched in a solution of 50-50 water and hot muriatic acid and used to obtain a macrograph of a horizontal section from the surface to slightly beyond the center of the 23-in. ingot dimension. Cuts No. 5 and 3 (lx81/2xl0 in. each) from sections A through H were treated in a similar manner to obtain a macrograph of a horizontal section from the surface to slightly beyond the center of the 35-in. ingot dimension. The composite macrograph of these horizontal ingot sections, which shows a vertical section of the ingot from top to bottom, is shown in Fig. 2. It should be noted that sections No. 2 are normal to sections 5 and 3 in the composite. Drillings for chemical analyses were obtained from selected positions within the above-mentioned ingot sections as noted in Fig. 3. The oxygen content was determined by the vacuum-fusion method. Samples for microscopic examination were cut from

Jan 1, 1954

THE Institute assembled in Packer Hall of the Lehigh University, the President, Mr. David Thomas, of Catasauqua in the chair. Professor Henry Coppée, President of the Lehigh University, made an address of welcome to the Institute, and placed at its disposal a convenient hall for purposes of meeting. Mr. Thomas tendered his resignation as President of the Institute, as advancing years prevented him from actively participating in its meetings. The Institute declined to accept the resignation, and, on the assurance that active duties would not be expected of him, Mr. Thomas was induced to withdraw it. Invitations were received from Mr. B. C. Webster, President of the Lehigh Zinc Company, to visit the mines and works of the company; from Mr. Charles Brodhead, to visit the Chapman Slate Quarries; and from the Lehigh Coal and Navigation Company, to visit their works at Summit Hill and Mauch Chunk and the Nesquehoning Tunnel. The Council reported the names of persons already elected in the two classes of members and associates. The following resolutions were passed : Resolved, That a committee of three be appointed, who shall take into consideration the printing and publishing of papers originating with the Institute, and that a uniform system as regards size and execution be adopted. The committee appointed consisted of Messrs. R. W. Raymond, E. B. Coxe, and the Secretary. Resolved, That the Council design and prepare a seal for the Institute at the earliest practicable time. Resolved, That a committee of six, with power to add to its numbers, be appointed to examine into the question of the more economical production of iron in this country. The committee appointed consisted of Messrs. G. W. Maynard,

By J. S. Woodward, F. B. Plummer

The measurement of the rate of flow of liquids through sands dates back to 1856, when H. d Arcyb, a French physicist, carried out his classic experiments on the flow of water through sand layers. The earliest recorded data on relationships of pressure to flow of fluids through porous rocks in this country are those of Newell 23 in 1885. The first comprehensive studies of flow were made in 1898 by King15, who measured the rate of flow of water and air through consolidated and uncon-solidated sands and published the results. From 1900 to 1920 there appears to have been little interest in permeability. In 1920 the increase in demand for oil led the U. S. Bureau of Mines to begin a series of experiments to determine subsurface relationships of oil and water and the characteristics of their flow. Mills18 studied the relationship of flow of liquids to text- and structure of the sands, and Melcher17 in 1925 made a quantitative study of effect of changes in pressure on rate of flow of crude oil through Oklahoma oil sands. Since 1930 the importance of flow measurements to production of oil and gas has been emphasized by a large number of excellent investigations. Among these the works of Fettke9.10, BarbI.2, Cloud6, Nutting24-", Bot-set4, Nevin22, Tickell32.33, Fancher, Lewis and Barnes8, Moore, Schilthuis and Hurst19, and Wyckoff, Botset and Muskat"-39 have contributed much to our knowledge of the technique of permeability measurements and to the laws of liquid and gas flow through porous sands. The application of their work has led to the establishment of laboratories for measuring the permeability and porosity of oil sands by most of the large companies. All the investigations, except those of Wyckoff, Botset and Muskat, and Moore, Schilthuis and Hurst deal with linear flow; that is, flow in a more or less straight line through a given cross-sectional area of sand. Three years ago, at the University of Texas, experiments were started to measure radial flow of liquids through sands; that is, flow from all directions toward a central opening—the conditions that operate in a

Jan 1, 1937

By E. D. Gardner

INTRODUCTION OIL shale deposits have been exploited in various countries throughout the world, but generally with government aid. The oil-shale industry of Scotland perhaps is the oldest and best-known; the largest was conducted in Manchuria by the Japanese during World War II as a source of liquid fuels for military uses. In general, foreign oil-shale deposits that have been exploited are much lower grade than those in the western United States. Considerable interest began to be shown in western oil shales in 1916; the peak of activities was in 1923. The Catlin operation, near Elko, Nevada, perhaps was the nearest approach in this country to an oil-shale enterprise on a commercial scale. Over 100 companies were formed, ostensibly for exploiting the oil shale; a large number of them, however, proved to be stock promotions only, which gave the embryo industry a black eye. The Bureau of Mines operated an experimental oil-shale retort plant near Rifle, Colorado, from September 1926 to June 1927 and again from April 1928 to July 1929, after which the plant was dismantled. By this time the East Texas oil fields had come in and the country lost interest in substitute liquid fuels. During World War II the Nation again became concerned about the magnitude of its petroleum reserves. Congress (April1944) directed the Bureau of Mines to build and operate demonstration plants to produce synthetic liquid fuels from coal, oil shales, and agricultural and other products; a five-year program was authorized. As a part of this program the Bureau of Mines has built, at Anvil Points near Rifle, Colorado, a retort plant and developed an experimental mine to supply the plant with oil shale. An important part of the mining work at Rifle is to devise methods and select practices for mining the oil shale on a commercial scale at the lowest practicable cost. The product to be mined has a relatively low value, a fact that must be kept continuously in mind. The combined aim of those in charge of the mining and those in charge of retorting is to demonstrate that the shale oil can be produced at a cost per barrel corresponding to the current quotation for crude petroleum -or at least very close to it. Plans call for an uninterrupted flow of broken oil shale from the face in the mine, through crushers, through the retorts and thence to the disposal dump. The disposal of the spent shale in the Rifle area should present no unusual problem. Mining research has consisted so far of paper studies of the general phases of the problem, determination of the widest span that the roof stone will stand safely unsupported, and drilling problems. Underground development has not proceeded far

Jan 1, 1947

By David P. Hale, Guy W. Jordan

High-iRon cements have a number of advantages over cements carrying little or no iron. The presence of iron in Portland cement aids in the manufacture of the cement and also imparts certain advantageous physical properties to the finished product. In manufacture, the presence of iron lowers the fuel consumption, increases the ease of proper"burning, and lessens the destructive action of the charge on the kiln refractories. In the finished cement the presence of iron reduces the expansion and contraction, adds strength, adds increased resistance to"freezing and thawing, and increases the resistance of the cement to sea "or sulphate waters. [" During the past few years the construction of numerous dams through- "out the Southeast by the Tennessee Valley Authority has stimulated the "production of high-iron cements. At present a great number of specifica- "tions call for an iron cement, and the industry is supplying this demand "with a Portland cement carrying approximately 5 per cent iron oxide. "Several manufacturers are now making practically all of their cement "of this type and a number of others manufacture it as a special cement "over short periods to meet demands from the Tennessee Valley Authority "and other buyers. " The recent increase in the use of iron in Portland cement has created "a market for iron products that previously was nonexistent. The chief "sources of supply for the cement manufacturers at present are iron sand, "iron sinter and slag, and ocher. The Copperhill mining district, Ten- "nessee, supplies both iron sinter and slag for use in cement. The Carters- "ville district supplies iron sand, ocher, and some iron resulting from the "magnetic separation of iron from barite. The advantages of these "products vary according to the chemical properties of the raw materials "and the methods of handling used by the different manufacturers. Where "the iron is to be handled by conveying belts and in hopper cars, the iron"sand and sinter and slag are preferable. Where the silica content must "be raised, the iron sand is doubly advantageous because it supplies both

Jan 1, 1942

By J. L. Rodda

THE desirability of a uniformly sized abrasive for metallographic polishing has probably been recognized in a general way for a long time. Certainly all metallographers have recognized the damage that can be done to a polished surface by a piece of grit, especially if one of the softer metals, such as zinc or aluminum, is being polished. It is to be doubted, however, whether many metallographers have had any adequate idea of the particle size of the abrasives they were using or of the range of sizes encountered in any given grade of abrasive. At any rate, the descriptions of abrasives for metallographic work found in the literature are generally very meager. It was with the idea of securing an abrasive with a limited range of particle size that a study of this problem was commenced. Commercial abrasives, even when recommended for metallographic work, are made up of particles of varying sizes. One such abrasive contains some particles so fine that they remain in suspension for days and other particles so coarse that they settle at the rate of 3 in. per minute. It is evident that the coarsest particles are over 100 times the diameter of the smallest ones, or over 1,000,000 times the volume. The hopelessness of avoiding scratches under these conditions is evident. Vanderwilt1 has described a laboratory method for grading abrasives in which the elutriator is used. Le Chatelier&apos;s method, described by Goerens,2 also makes use of an elutriator. However, the elutriator is too slow for this purpose and requires too delicate a control for the range of sizes desired. The method of stirring up the abrasive in water, allowing it to settle for as given time, then drawing a measured depth off the top of the suspension, has been finally adopted as the simplest proce-dure. The largest particle in a given portion is. then determined by Stokes&apos; law:3

Jan 1, 1931

By R. N. Bhattacharyya

In recent years, increased attention is being paid to the application of oil-agglomeration technique for (a) improved recovery of low- ash clean coal, (b) effective beneficiation of low-grade coking coals and (c) removal of pyrite sulphur from high-sulphur coals. In this technique, which has been proved to be more effective than convention- al froth-flotation, advantage is taken of the oleo-philic nature of finely ground coal to separate it under controlled conditions from the associated minerals which are hydrophilic in nature. Unlike froth- flotation, no aeration is needed in the process and the concentrates which are obtained in the form of agglomerates or micro-pellets have easier dewatering characteristics. Optimization of operating variables in treating individual raw feed is a pre-requisite for the successful application of this process. A 10 gram batch unit was employed in the present test series. This paper presents - results from these investigations on such operating variables as (i) size of coal, (ii) amount of oil used, (iii) time of stirring, (iv) rate of stirring, (v) solid content in slurry and (vi) effect of conditioning.

Jan 1, 1977

Some coal was mined in this area under lease from the Indians before it became a state. Table 75 shows all production figures available. [ ]

Jan 1, 1942

By P. E. McKinney

Developments in engineering during the past decade, particularly as applied to marine construction, mining machinery and other purposes in which corrosion offers a serious problem, have created a large demand for a non-ferrous metal highly resistant to corrosion and at the same time useful in general construction work as a substitute for steel without materially decreasing the factor of safety or increasing the weight of the various parts over that ordinarily used in the case of mild steel. To obtain the combination of desired properties many compositions have been proposed and used with excellent success, but at the present time probably the most popular and most widely used combination is the non-ferrous alloy commonly called manganese bronze. This is nothing more than a high brass to which have been added, by the proper method of alloying, comparatively small percentages of aluminum, iron, or manganese with the definite purpose in view of strengthening the alloy and rendering it more dense and close-grained than the average yellow-brass casting. In the manufacture of manganese bronze a great deal has been said about the importance of using only the highest grades of raw material and the beneficial or detrimental effects, as the case may be, of various impurities, as well as the importance of adding the ingredients according to various formulas proposed; but in most of these cases the literature on the subject has dealt principally with the manufacture of this alloy from virgin metals and raw materials of the highest purity. It is the purpose of this paper to deal particularly with the possibilities that lie in the proper development of methods for manufacturing such an alloy by more economical methods than those which have usually been discussed in other literature on the subject. Shortages have recently existed in raw materials needed for many products entering into the various branches of engineering work, particularly the non-ferrous metals, and during the next few years of reconstruction the country will be flooded with many

Jan 1, 1919

By J. R. Ross, J. B. Rosenbaum

Bureau of Mines research has resulted in the development of fluid- bed ion-exchange columns for recovering uranium from slime pulps. In pilot plant tests, slime slurries containing up to 6 percent solids were processed at flow rates of 10 gallons per square foot per minute with high uranium recoveries and efficient resin loadings. Uranium was effectively eluted in a laboratory fluid-bed elution column at eluate-to-resin ratios of less than 5:1 and eluate flow rates of 3 gallons per square foot per minute. Construction costs of mills using these improved ion exchange techniques are estimated to be 25 percent less than for mills using solvent extraction of clear solutions. For mills having a capacity of 2,000 to 2,500 tons of ore per day, the saving would be in the range of $2.5 million. In addition, a saving of about $0.80 per ton of ore in total operating costs is indicated.

Jan 1, 1973

The stabilization of a gravel road with soil is a method of treatment developed in recent years by the United States Bureau of Public Roads for the purpose of binding the constituents together better, and maintaining a more durable surface. The process consists in adding to the gravel or crushed stone and sand, a soil mortar, so-called, of fine sand, silt and clay, mixed in the proper proportions. The coarse gravel and sand supply structural strength and hardness; the fine sand adds embedment support to the coarse sand; the silt acts as a filler to prevent the granular particles from rocking; while the clay serves not only as a binder but also provides pores minute enough to cause connecting moisture films which are supposed to have high cohesive properties&apos;. It will be recognized that the clay is an important ingredient both when wet and dry, and should not show excessive expansion when wet, nor correspondingly high shrinkage in drying, as otherwise there is danger of unseating the nonplastie particles. Such a stabilized road, although an improvement on one with a floating surface, will in course of time be subject to wear, and become dusty when the clay dries out and breaks up. It has been found that if some salts are added to the road mixture they tend to maintain the soil moisture and prevent dustiness of the road or raveling of the road surface. In addition to this, it is claimed that these dissolved salts cause a thinning of the moisture films on the particles, thus permitting greater compaction of the road mixture, and thereby increasing its density. This fact can be proved by noting the increased compaction which a road mixture shows when certain salts are added to the soil water. Since certain chemical substances such as sodium chloride are electrolytes, the question arises whether they cannot have wine effect on the qualities of the clay in the soil mortar, and perhaps improve them. In view of the fact that certain salts seem to exert a favorable effeet on the road mixture it is desirable that they he held in the road soil as long a time as possible.

Jan 1, 1938

By H. R. Hanley

The characteristics of alloyed anodes and their influence on the products of electrolysis and power consumption have been noted previosly ously in the literature.&apos; This paper presents data in continuation of the subject given in an earlier paper by the authors.2 As noted in the authors1 previous paper, the objectives of this work are the reduction in the cell voltage and the purity of the cathode product resulting from the use of alloyed lead anodes. The fundamental facts developed in the previous paper were: (I) that the presence of a small amount of calcium lowers the anode potential approximately 50 per cent. below that of pure lead; and (2) that thallium when present to the extent of 4 per cent. rendered the anode practically stable, thereby lowering the contamination of the cathode by lead to a very insignificant amount. The specific features determined in this recent work are as follows: 1. The lowest limit of calcium in the lead which will still give maximum lowering of the anode potential. 2. The characteristics of the thallium-calcium-lead anode. 3. The characteristics of the silver-calcium-lead anode. 4. The characteristics of the thallium-silver-calciurn-lead anode. It was determined that 0.1 per cent. calcium in the anode was sufficient to lower the anode potential approximately 50 per cent. Table 1 shows the characteristics of alloyed anodes tested. The anode composed of 0.1 per cent. calcium, 4 per cent. thallium, and 95.9 per cent. * Professor of Metsllurgy, Missouri School of Mines. t Professor of Metallurgy and Ore Dressing, Hea.d of Department, Missouri School of Mines. Assistant Professor of Metallurgy, Missouri School of Mines. 1 Among others, see C. G. Fink and Li Chi Pan: Insoluble .Anodes for the Electrol-ysis of Brine [Trans. Amer. Electrochem. Soc., (1926) 49, 83-1341 and other papers by these authors. U. CJ. Taintori, 8. G. Taylor arid H. P. Ehrlinger: Lead Alloys for Anodes in Electrolytic Production of Zinc of High Purity. Truns. A. I. M. E. (1929) 192-200. 2 H. R. Hanley, C. Y. Clayton, D. F. Walsh: Investigation of Anodes for Production of Electrolytic Zinc. Trans. A. I. M. E. (1930) 275

Jan 1, 1931

By Chester W. Washburne

At present it is impossible to estimate closely the amount of oil obtainable from a given area of land. However, after the completion of a few properly distributed prospect wells, one can calculate the approximate yield of the sands penetrated, with a probable error of say 50 per cent. Even rough predictions of this kind are of value in large operations. Without wells upon it, one can never be absolutely certain that an area will produce any oil whatever, and one can only indulge in wild guesses of the probable productive area, before the geological structure has been carefully contoured and the top of the basal water plotted on a map. This requires wells. At times it is desirable to form an idea of the possible yield of oil in advance of drilling, as in cases where the price asked for undeveloped land seems too high, but where the probability of finding oil is furnished by neighboring development, supported by the geology. In such cases the most one can do is to make an estimate of possible maximum yield, which may of course far exceed results, and which is of use mainly in the prevention of excessive initial investment. The method is very significant in a general way, as in regions like the Bighorn Basin, Wyoming, where the productive sands in the Cretaceous shale are so few and so thin and fine that they cannot develop very great production, although the high quality of the oil probably will counterbalance this defect sufficiently to give local profit in favorable areas. Reservoir Capacity of Sands.—The porosity of a stratum is the measure of its maximum reservoir capacity for liquids and gases. The porosity may be determined experimentally and must be used in connection with the total volume of the sand.

Jan 1, 1915

By John B. Mertie

MONAZITE formerly was described as moribund, but, in the light of recent developments, it is no longer so. It is the common source of the rare earths and thorium, both of which are becoming progressively important in industrial and other applications. Moreover, by the action of foreign governments, the sources on which the United States has depended for its supply are now either restricted or cut off entirely. Monazite has thus become a scarce mineral and processors in this country are endeavoring to acquire it from all available sources. RARE EARTHS AND THORIUM The rare earths proper, as defined by spectroscopists, are the oxides of cerium, praseodymium, neodymium, prometheum, samarium, europium, gadolinium, terbium, dysprosium, holmium, erbium, thulium, ytterbium and lutecium, with atomic numbers ranging respectively from 58 to 71. Chemists include with the rare earths scandium, yttrium, and lanthanum, with atomic numbers respectively of 21, 39, and 57. Thorium, with an atomic number of 90, is analogous to lanthanum, in that it precedes a second group of elements, whose oxides constitute the "rare earths of higher order." These are protactinium, uranium, neptunium, plutonium, americium and curium, with atomic numbers ranging respectively from 91 to 96. The last four mentioned are artificially prepared elements that so far have not been detected in nature. The rare earths with odd atomic numbers, except europium and lutecium, have no natural isotopes; and the two exceptions have only two isotopic forms. Those with even atomic numbers have from 4 to 7 natural isotopes. Samarium148 is radioactive, disintegrating over a half- life of 1.4 X 10 11 years with the emission of alpha rays. Lutecium176 is weakly radioactive, disintegrating over a half-life of 2.4 X 1010 years, with the emission of beta and gamma rays. At least 64 radioactive isotopes of the rare earths proper have been artificially prepared. Thorium is a strongly radioactive element, with a half-life of 1.39 x 1O10 years, which disintegrates through a series of 14 isotopes of 10 elements. The two longest lived and most important of these are

Jan 1, 1949

By T. G. Digges, C. L. Vold, M. R. Achter

A study was made of the effect of the growth conditions on the perfection of single crystals of niobium (columbium). Dislocation densities, determined by means of double-crystal diffractometer measurements , were not greatly affected by the method of crystal preparation but could be reduced by annealing treatments. However, the size, sharpness, and tilt angles of the substructures, observed with X-ray reflection macrograph, were sensitive to variations in growth procedures as well as to subsequent thermal treatments. Although the dislocation density was the same in both types, there were more low-angle bound-aries in crystals grown by zone melting than in those prepared by strain anneal. Mechanisms to account for these observations are discussed in terms of dislocation movements. A planned study of the structure-sensitive properties of refractory metals required the use of single crystals of a high degree of structural perfection and, for ease of handling, of large cross section. It appeared that the strain-anneal technique could satisfy both of these requirements. First, crystals grown in the solid state have been reported to be more perfect than those obtained from the melt.&apos; Second, the diameters of rods which may be produced by zone melting should have a theoretical limit determined by specific gravity, thermal conductivity, and surface tension, while the diameter of strain-annealed rods is limited only by practical considerations. Previously it was shown that niobium (columbium) single crystals of 1 in. diam2 may be grown by strain anneal, compared to the 0.5 in. maximum diameter achieved by zone melting, as reported for molybdenum by Belk.3 The current research was undertaken to investigate and optimize the effect of various process variables on the perfection of 1/4 and 1/2-in.-diam niobium single crystals grown by strain annealing and to compare their perfection to those grown by zone melting. Characterization of these crystals was more conveniently accomplished by means of X-ray than by metallo-graphic techniques. EXPERIMENTAL PROCEDURE Specimen Preparation. Zone-melted crystals of 1/4 in. diam were produced by the standard electron-beam zone-melting technique. The swaged and cleaned rods were outgassed, in the solid state at a temperature near its melting point, at a rate of 12 in. per hr, and single crystals were grown by making two molten passes at 2 in. per hr. By maintaining a zone length of 4 to % in., very uniform single crystals several inches long were obtained. For the strain-annealed crystals, an induction heater was used, in preference to other types of heating, to take advantage of the good penetration of large sections. A five-turn coil, 1 in. long, operating at 10 kc and powered by a motor generator, was contained in a vacuum chamber. The rod, suspended from the upper end, was raised through the coil for both recrystallization and crystal growth. In preliminary work single crystals of the same material were also grown with single and multiturn coils powered by a 450-kc generator. A vacuum of 2 X 10-6 Torr was maintained at temperatures up to 2400°C. Starting with electron-beam-melted ingots of 21/2 in. diam, the analysis for which is given in Table I, the material was cold-swaged to the desired cross section of 1/4 and 1/2 in. diam and then recrystallized. The rods were then strained in a tensile machine and converted to single crystals by passing through the induction coil. As with zone melting, control of orientation is possible by the use of special procedures. Other investigators, see for example Williamson and smallman,4 have reported that orientation control may be achieved by a bending technique. In the present work the strained rod is partially lowered through the coil to start the growth of the crystal. Then it is removed and bent at a point in the poly crystalline portion. Finally, it is returned to the chamber and growth is continued "around the corner". This procedure has certain limitations. If the bending operation exceeds the critical strain, recrystallization may take place. Also, the amount of bending which can be imparted to the rod is limited by coil geometry, and up to now has been 10 deg. However, by repeating the bending and growing operations it should be possible to attain any desired orientation. In preparation for X-ray examination, single crystals were sectioned and planed by means of the spark-erosion technique. To obtain the maximum reflected intensity, the (110) plane was exposed for examination. They were then etched 3 to 5 min in a mixture of con-

Jan 1, 1967

By W. A. Backofen

THE texture of cold-drawn copper wire has been described most often as a composite of [Ill] and [loo] directions aligned parallel to the wire axis.&apos; Hibbard2 suggested that sufficient reduction will result in a single [111] texture and reported that after a reduction in area of 96.4 pct, such a texture was nearly obtained. Other work3-4 has shown that recrystallization within the temperature range of 300" to 1000°C does not alter the texture established by cold-drawing. In general, however, the texture of cold-drawn end annealed copper wire is not as well defined as the deformation texture. In the work reported here it was found that the double-fiber, deformation texture persists even after a reduction in area of 97.3 pct, and after recrystallization the texture is practically all [l00]. The wire used in this work was prepared in the following way. A 3/4-in. diam length of annealed OFHC copper was cold-drawn to a diameter of 1/8 in., a reduction in area of 97.3 pct. Each step in the drawing operation brought about a reduction in area that varied from 6 to 10 pct. Short lengths of this wire were etched in a 50-pct solution of nitric acid to a diameter of approximately 0.01 in. The texture of the cold-drawn specimens was determined with the conventional X-ray transmission diffraction technique using filtered copper radiation. The X-ray beam was directed perpendicularly to the wire axis and the diffraction rings were recorded on a flat film. Fig. la is typical of the photo-grams obtained and reveals that the cold-drawing schedule described above introduces a distinct, double-fiber texture with both [Ill] and [l00] directions aligned parallel to the wire axis. Supplementary measurements with a Geiger-Mueller counter of the intensity of reflection from (111) planes showed that the [111] component was much more predominant than the [l00]. Additional specimens of the drawn and etched wire were annealed in a salt bath at temperatures from 300" to 450°C. The texture of the recrystal-lized wire was studied with the same technique applied to the cold-drawn wire. Fig. lb is an X-ray photogram of a specimen annealed for 1 ½ at 300°C and is typical of those obtained from re-crystallized specimens. The photogram shows that recrystallization of this material is accompanied by the almost complete elimination of the [111] component of the deformation texture. A pronounced strengthening of the [100] component was evident from intensity measurements with a Geiger-Mueller counter. In summary, the deformation texture of cold-drawn OFHC copper wire, after a reduction in area of 97.3 pct, may still be described as a composite of [Ill] and [loo] directions aligned parallel to the wire axis. Recrystallization of such wire at temperatures from 300" to 450°C introduces a texture which consists almost entirely of a [loo] alignment. Acknowledgment Sidney Rolle of the Scomet Engineering Co. generously supplied the OFHC copper used in this work. References &apos;C. S. Barrett: Structure of Metals. p. 382 (1943) New York. McGraw-Hill Book Co. 2 W. R. Hibbard, Jr.: Trans. AIME (1949) -185, p. 598; Journal of Metals (Sept. 1949) TN 19E. 3 P. 422 of ref. 1. &apos;E. Schmid and G. Wasserman: Ztsch. Physik (1926) 40, p. 451.

Jan 1, 1952

By P. A. Boeck

(San Francisco Meeting, September, 1915) THE thermal insulation of high-temperature equipment for industrial purposes is a subject that has not received from engineers and designers the attention its importance deserves. This may be attributed to a number of causes: In the first place, heat flow is a rather difficult factor to measure under the working conditions of an industrial furnace, and until the comparatively recent introduction into certain operations of the heat balance sheet, with a systematic attempt to account for the discrepancies in the totals, the various causes of heat losses and the reasons for their existence were not brought to light. Moreover, such rapid advancement and radical changes in the design of equipment, especially in metallurgical lines, have occurred that practice has apparently outdistanced the theory of design. In the modern tendency toward greatly increased size of units, effort has seemingly been made to utilize the heat of fuel gases without proper. attention having been paid to conserving heat energy and confining it strictly to the points of maximum activity. The systematic study of the thermal properties of structural materials, which is being carried out by various government bureaus and also by a number of technical societies, is forming the basis for more intelligent and consistent work in the economically important subject of prevention of fuel waste.

Jan 8, 1915