Search Documents

By R. C. de Lange

An improved replica technique is developed for a nondestructive study of the nucleation and growth of fatigue cracks. Three different growth stages of a fatigue crack were observed. An initial stage of high growth rate is followed by a long period of very slow growth, until finally a third period of high growth rate leads to fracture. THE metal-fatigue process is of a very complex nature. The experimental approach towards fatigue is susceptible to many minor influences which, together with the unavoidable scatter in testing results, makes the interpretation a matter of extreme care. The generally accepted fact that, in a homogeneous material, the fatigue cracks start at a free surface indicates that surface studies may contri-but in an essential way to a better understanding of the fatigue mechanisms. Indeed metallographic observations of the fatigue phenomena have been very fruitful in the last decade. The study of extrusions, intrusions, and persistent slip bands has contributed much to the present knowledge of the early processes in fatigue.' The drawback of the current metallographic techniques lies in the fact, however, that either observations of fatigue phenomena had to be made in a destructive way after an only partly executed test or a sequence of observations on the same test bar was only possible on notched specimens.2 4 In both cases an uncertainty exists as to the nucleation and growth of the fatigue crack in an unnotched test bar, where the crack can start at any place of a large area and develops in a test bar, which is macroscopically

Jan 1, 1964

By George Gardner

THE application of wet cleaning processes for the beneficiation of bituminous coal has created in some localities a problem in the recovery and disposal of fine solids in the washery water. The maximum allowable concentration of these solids in the washery circuit that is consistent with satisfactory operation of the cleaning units remains a controversial point. It has, however, been generally recognized for a number of years that some degree of control should be exerted over the concentration of such material. Early methods of control involved intermittent or continuous dis-charge of a portion of the plant slurry into near-by streams or settling ponds, and this persisted even after the adoption of settling tanks or cones. The practice is not always economical, for two reasons: first, because of the waste of coal, and, second, because it is sometimes difficult and expensive to obtain an adequate supply of water. The latter condi-tion often is aggravated by chemical treatment of the make-up water that is necessary to prevent excessive corrosion of plant equipment. The modern approach to this problem has been the adoption of continuous thickening devices. However, because such equipment occupies consid-erable plant space and is somewhat expensive to construct, the practice of loading these thickeners beyond their rated capacity is widespread, there-fore often the performance of such units is not altogether satisfactory. In recent years, European washeries have increased the rate of settling of the fine coal from the slurry by the addition of specially pre-pared starch solutions. These reagents cause flocculation of the solid particles and thereby increase the rate of sedimentation.

Jan 1, 1939

By R. E. Boehler, N. C. Ludwig

At Buffington Station, Gary, Ind., Universal Atlas Cement operates fourteen 8 x 10Y2 x 155-ft cement kilns in mill 6 and two 11 x 360-ft kilns in the Harbor plant. The No. 11 and 12 kilns in mill 6 are equipped with Manitowac recuperator sections. This report describes studies in measuring exterior shell temperatures on several of these kilns and the development of a traveling radiation pyrometer with certain novel features.

Jan 2, 1960

L. K. ARMSTRONG H. L. NORTON SECRETARY-TREASURER of SECRETARY-TREASURER Of COLUMBIA SECTION ARIZONA SECTION PERCY E. WRIGHT A. B. CARPENTER SECRETARY-TREASURER Of SECRETARY-TREASURER Of PUGET SOUND SECTION SOUTHERN CALIFORNIA SECTION

Jan 8, 1919

By N. J. Themelis, R. V. Flint

In a four-year period between 1973-76, the Metal Mining Division of Kennecott Copper Corp. conducted a company-wide program of operations improvement which involved line and staff personnel from all company functions. Specialist teams performed detailed studies of all operational aspects at Kennecott's four copper mines and concentrators, four smelters, and two electrore-fineries. The specific recommendations that resulted may transform the Metal Mining Division into the country's lowest cost producer of copper by the mid-1980s. In this article, N. J. Themelis and R. V. Flint describe the mechanics of MMD's integrated approach to operations improvement.

Jan 6, 1979

By Bension Varon

Systematic projections of mineral supply, demand and prices are an integral part of the mineral sector planning process. As such, their primary value is not as prophecies but as devices for imposing discipline on thinking about the future and as means of ensuring consistency in policy decisions. Both the present and the broad outline of the future as presently discernable affect projections on specific minerals. The present world mineral situation reflects most prominantly the recent commodity cycle while our view of the future is largely shaped by perceptions and attitudes of policy-makers and the public over larger issues. Mineral commodities are of considerable importance to various countries. This in itself dictates a strong interest in systematic projection activities, the need for which is heightened by the volatility of certain basic variables affecting mineral demand in the world. It is useful for presentation purposes to discuss the various techniques suited for projecting mineral trends under three principal headings, viz., econometric modeling, systems analysis and technological forecasting. In addition, two specialized variants, input-output analysis and resource base modeling, are discussed. In each case, a brief description of the approach and some indication of its application to projections of mineral commodities are provided.

Jan 1, 1977

Jan 1, 1912

By Erwin J. Durrer

The development of planning in the petroleum industry is de- scribed and the current status analyzed. Worldwide transportation networks led to corporate models which caused a differentiation between operations research and planning groups. Ranking of projects solely by ROI proved infeasible because of the diversified nature of the industry. Qualitative elements such as synergism with ongoing operations and the external socio-economic environment had to be included, leading to business plans based on scenarios of possible futures and stressing growth-opportunities over cash-flow rich mature product lines. In addition, decision analysis is finding applications in large capital, high uncertainty situations such as planning for synthetic fuel development.

Jan 1, 1977

By Henry Howe

1. Introduction.-This paper is based in large part on the examination of two rings, shown in section in Fig. 4 to 15, cut from an eroded 14-in. (35.56-cm.) gun, liner, and containing, according to Booth, Garrett, & Blair: Carbon, 0.380 per cent.; manganese, 0.655 per cent.; nickel, 2.810 per cent.; vanadium, 0; chromium, a few hundredths of 1 per cent.; tungsten, 0; molybdenum, 0. These rings were received from Admiral Joseph Strauss, then Chief of Ordnance, U. S. Navy, through the kindness of Mr. Hudson Maxim, Chairman of the Committee on Ordnance and Explosives,, of the U. S. Naval Consulting Board.

Jan 2, 1918

By Y. Nakada, U. F. Kocks, B. Chalmers

The stress-strain behavior of the gold single crystals in easy glide was found to be affected by the specimen dimension which is parallel to the projection of the Burgers vector of the primary-slip system. The larger this dimension is, the larger is the slope of easy glide. Previously severa1 investigators attributed the size effects to either the existence of surface films or the grip constraints. However, in this experiment both of these possible causes were not present. It is proposed that the length of slip path (defined as the crystal dimension parallel to the Burgers vector of the primary system) is the controlling factor in the size effect observed in gold. THERE are many possible effects of the specimen dimension on the work-hardening behavior of single crystals: grip effects which prevent end regions of the crystal from deformation or rotation; effects of a surface film, for example a coherent oxide; effects of a subsurface layer of accidental or intentional

Jan 1, 1964

By A. L. Barnes, A. M. Rowe

A heat transfer study was made of hot gas injection into oil shale through wells interconnected by vertical fractures. This analysis involved the simultaneous numerical solution of a nonlinear, second-order partial differential equation that describes two-dimensional conduction heat transfer in oil shale and a nonlinear first-order partial differential equation that describes convection heat transfer in the fractures. Three nonlinear, temperature-dependent coefficients were used in this work; they are thermal conductivity, thermal capacity and retorting endothermic heat losses of oil shale. Vertical fractures were considered to be of finite height. Although vertical conduction heat transfer was not considered, an estimate of the error resulting from this limitation was made. The effects of injected gas temperature, injection rate, system geometry, cyclic injection and time upon retorting efficiency were investigated. Results from this study show that the rate of retorting oil shale is a direct function of both injection temperature and rate, and the theoretical producing air-oil ratio:(AOR) is an inverse function of temperature. Retorting rates are constant until "breakthrough" of the 700 F isotherm at the producing well, assuming constant injection parameters. Retorting rates for bounded systems are higher than the analogous unbounded systems and likewise AOR's are less. The use of an alternating injection-soak routine with high injection rates is less efficient than continuous injection at lower rates. These results indicate that injection temperatures on the order of 2000F or greater may give theoretical AOR's in the economic range. INTRODUCTION Over half of the known oil shale reserves are located in the U.S., and most of them lie in the Piceance Creek basin of Western Colorado. The Colorado oil shale outcrops on the edges of the Piceance Creek Basin. At the outcrops the shale beds are relatively thin, from 25 to 50 ft thick. In the center of the basin the oil shale is as great as 2,000 ft thick and is covered with 1,000 ft of overburden. It has been estimated that there are over 1,000 billion bbl of oil in shales having an oil content over 15 gal/ton in this basin. Oil shale does not contain free oil but an organic matter called kerogen. Kerogen yields petroleum hydrocarbons by destructive distillation. It must be heated to approximately 700F, at which temperature it decomposes into shale oil, gases and coke. The U.S. Bureau of Mines and, more recently, oil companies have conducted considerable research on surface retorting methods to economically recover oil from this shale. Another approach to exploit the oil shale deposits, in particular that portion having 1,000 ft of overburden, is to retort the oil shale in place and produce the liquid and gaseous hydrocarbons through wells drilled into the shale. Some research has been done on this approach.l,2 There are several variations to the in situ retorting approach. These variations fall into one of two groups, depending upon the geometry of the system: (1) retorting in a highly fractured or broken up matrix; (2) retorting from single fractures between production and injection wells. The latter is the group studied. Several investigators,3-6 using various assumptions, have studied flow of heat through horizontal systems. The objective of this work was to make a heat transfer study of in situ retorting oil shale by hot gas injection through wells interconnected by single vertical fractures of finite height. The oil shale thermal conductivity, thermal capacity and retorting endothermic heat losses were considered to be functions of temperature. A knowledge of the

Jan 1, 1969

By R. B. Schluter, M. M. Fine

Development of a process for winning copper from pelletized chalcocite concentrate is underway at the Bureau of Mines, Twin Cities Metallurgy Research Center. The new route from concentrate to metal by which the Bureau seeks to eliminate matte smelting and converting includes a two-stage fluid bed treatment. In the first stage, pelletized concentrate containing 32%Cu and 7% S is first desulfurized to less than 1.0% S in an oxidizing atmosphere. In the second stage, the calcine is metallized by reduction with hydrogen. Thereafter, the reduced product plus 10% CaO is routed to a smelting furnace which separates metallic copper from the gangue. Recovery and Cu content at this point are in the 97-98% range. This product must be refined to remove sulfur and iron so the metal is suitable for making wirebar copper. An important feature of the process is fine concentrate pelletization prior to fluid-bed treatment. This permits a shorter reaction time, a decrease in dusting and easier subsequent processing. In a broad sense, sulfide copper pyrometallurgy is a batch sequence in three separate vessels, i.e., a reverberatory furnace to yield matte copper, a converter to produce blister copper and another reverberatory furnace to produce fire-refined copper. Matte-smelting has remained relatively unchanged since it became a universal practice some 50 to 60 years ago. It is now serving a wide range of smelter feed materials, but many concentrates are not immediately amenable to the process. There are abundant copper resources which lack sufficient sulfur and other elements lo sustain the full chemistry involved in matte-smelting. This necessitates adding sulfur to make the product fit the process, and usually none of the sulfur is recovered. From the standpoint of pollution alone, the development of a smelting technique for low-sulfur concentrates not requiring the addition of sulfur would be a significant gain.

Jan 1, 1970

By M. J. Kirwan, K. A. Covell

This paper covers a brief discussion of pumping 38° to 41° gravity oil from Wilcox sand wells ranging in depths from 4000 to 4900 ft. in the Seminole field, Oklahoma. As recently as a year ago it was the general belief among Seminole operators that most wells in that district could not be successfully or economically pumped. Also the idea was prevalent at that time that the crookedness of the rotary holes would cause a large amount of mechanical trouble and the use of the air-gas lift would leave the wells depleted with sand conditions and fluid levels unfavorable for pumping. At that time it was predicted that wells would be abandoned when the economic flowing and swabbing period was reached. Contrary to these beliefs it has been demonstrated that wells can be profitably pumped to limits as low as 10 bbl. of oil per day where conditions are favorable. The Serllinole field, unusual in its rapid development, has served as an experimental laboratory for many oil field pumping devices with which this paper will not concern itself. Discussion will be confined to equipment and methods in general use throughout the field. The outstanding features of equipment and pumping operations covered in this paper may be summarized as follows: 1. Pumping equipment from the standpoint of prime movers, energy cost, power transmission equipment, derricks, counterbalances, beam hangers, tubing, sucker rods, pumps, etc. 2. Pumping problems peculiar to the Seminole field, including the proper time at which to change from air-gas lift flowing to pumping. Pumping Equipment There have been no basic changes in pumping equipment in the past 20 years with the exception of some refinements in design brought about by the demand for equipment suitable for pumping deep wells. Results of research in the heat treatment of metals and progress made by the American Petroleum Institute in standardization of equipment, together with the cooperation of oil field equipment manufacturers, have

Jan 1, 1929

By L. L. Wyman

The exact nature of the changes that take place in the iron-nickel alloys, giving rise to the interesting and useful expansion alloys in the Invar range, has yet to be fully understood. Similarly, the ternary iron-nickel-cobalt alloys, which also possess such commercially useful expansion characteristics,1,2 are concerned with transformations that appear to be identical with those found in the parent iron-nickel alloys. The investigations on iron-nickel alloys in the range 26 to 29 per cent Ni have been reported by several authors3-9 wherein it is shown that there are factors other than temperature, such as stress and grain size, which play an important part in determining the temperature at which the low-temperature transformation takes place. It will be shown in this paper that the ternary iron-nickcl-cobalt alloys having nickel contents comparable to the alloys mentioned above behave in a parallel manner. The alloys in the range of 26 to 31 per cent Ni and 16 to 21 per cent Co have a coefficient of expansion of about 4.0 X 10-6 per degree Centigrade, and the alloys in this range of composition find considerable application in making glass-to-metal seals, because these expansion properties so well match commercial glasses. The behavior of these alloys is not a simple matter, for it has been observed in alloys of 28.5 per cent Ni and 18.5 Co that severe working ran cause the appearance of a second phase having a needlelike structure similar to the martensite structure in carhon steels. Fig. 1 shows the change brought about in an alloy of this composition when a strip of this material was cut with tin shears. This second phase has been identified as the body-centered cubic alpha phase, and it is the purpose of this paper to describe the results of some of the preliminary investigations in the study of the changes involved in these alloys. Materials The past work on these alloys has concerned itself primarily with materials made by the usual casting procedure and involving the use

Jan 1, 1939

The Library of the above-named Societies is open from 9 A.M. to 10 P.M. on all weep-days, except holidays, from September 1 to June 30, and from 9 A.M. to 6 P.M. during July and August. The Library contains about 55,000 volumes, including sets of technical periodicals and the publications of scientific and technical societies. Members of the Institute, with few exceptions, are forced to spend a portion of their time in localities isolated from sources of information. To these the Library can render valuable service through correspondence; letters requesting information will receive special attention. The Library is prepared to furnish references and copies of articles on mining and metallurgical subjects; to determine the existence of mining-maps, and to furnish general information as to the geology and mineral resources of all countries. All communications should be made as definite as possible so that the information received may be what is desired and not include collateral matter which may not be of interest. The time spent in searching for such collateral matter will be saved, and the information will be sent more promptly and in more usable shape. The members of the Institute can be of service to the Library by forwarding copies of mining-reports, maps privately issued, and similar material, which will be classified, indexed, and made available to other members. Suggestions for additions to the Library, either by purchase or personal solicitation as gifts, will be welcomed. It is hoped that members while in the city will use the Library freely, and assurance is given that most careful service will be rendered to them.

Jan 3, 1914

By R. B. Sosman, J. C. Hostetter

It is well known that ferric oxide, Fe2O3, is paramagnetic, while magnetite, Fe3o4, is classed among the highly ferromagnetic substances. But magnetic data on oxides intermediate in composition between Fe2o3 and Fe3O4 have been almost completely lacking. Fe2O3 and Fe3O4 form a solid-solution series, according to present evidence.' In this series the properties change continuously from Fe2O3 toward Fe3O4, as the percentage of FeO increases from zero toward 31.03, which is the percentage in magnetite. It is possible that there is a break in the series near Fe3O4, but it has not yet been possible to establish the existence of such a break experimentally. The occurrence of solid solution in this series is shown by the dissociation pressure, or oxygen pressure in equilibrium with the oxides, which falls continuously over the range from Fe2O3 to Fe3O4. The oxygen-pressure curves at 1100" and 1200" are shown in Fig. 1. The existence of solid solution is also demonstrated by the continuous change in optical properties from Fe2O3 over to a composition containing about 18 per cent. FeO, at which point the opacity of the oxide becomes so great that it is impossible to obtain measurements at higher percentages of ferrous iron. Natural oxides of iron intermediate in composition between Fe2O3 and Fe3O4 are much more common than is generally supposed. If a mineral oxide is not strongly attracted by a small hand magnet and if it gives a red streak, it is usually labeled "hematite." If it is strongly attracted by the hand magnet it is usually labeled "magnetite" without further tests. As we shall show later, oxides containing from 1 up to 31 per cent. FeO can be thus erroneously lumped together as "magnetite." It is a fact, nevertheless, that the great bulk of natural oxides of iron lie fairly near either Fe2O3 or Fe3O4 in composition. The reason will be

Jan 1, 1918

By E. I. Gordon

The electronic pickup tube is the image-to-video signal-converter or transducer in tele vision-like systems. Images may relate to visible light or IR excitation as in conventional TV systems, X-ray excitation as in some medical and production control applications, or electron excitation as in electron microscopy. The latter process is also important in some forms of light or X-ray sensitive pickup tubes as an intermediate step. In virtually all of these devices the image ends up as a stored charge pattern on a suitable target electrode and the video signal is created by periodically scanning the target with a low energy electron beam and removing the stored charge. In a major group of tubes radiation induced conductivity creates the charge pattern. In others, photoemission is used. In this paper an attempt is made to illuminate some of the device requirements placed on materials exhibiting radiation induced conductivity, some of the materials and techniques that are used, and the problems. The emphasis will be on visible light and IR sensitive targets although some attention will be given to X-ray and electron imaging. Photoconducting films as well as diode arrays will be discussed. ELECTRONIC pickup tubes find their greatest use in commercial, entertainment television, and in industrial and educational closed-circuit television. Video telephone systems, such as AT&T's PICTURE-PHONE System will become eventually the greatest user. Military use is also very important. Nevertheless the use of electronic pickup tubes in technology, science, and medicine is assuming ever greater relevance and demands the greatest diversity and perfection in the pickup tube art. Commercial television and closed-circuit television use requires visible light response, high resolution, low lag, and uniform response. Video telephone use requires the same plus extreme reliability, stability, and low cost. Military use emphasizes, in addition, sensitivity, IR response, and ruggedness. (Devices for far IR response will not be considered here.) The use of pickup tubes in medicine and biology emphasizes UV response for microscopy, X-ray response for radiology, and energetic electron response for electron microscopy. Astronomy and nuclear physics demands low light level response, storage ability, and resolution (here the tube is a successful replacement for film). The interested reader might profitably read Advances in Electronics and Electron Physics, vol. 12,' 16,2 and 22A3 and 22B4 for detailed discussion of the use, properties, and technology of electronic pickup tubes. In general, because of the importance of these uses, none of the above properties will be ignored. Nevertheless attention will be restricted to only those imaging devices, called pickup tubes, using a scanning electron beam to dissect the image with a resulting video signal for conventional CRT display. However pickup tubes have become so complex that many of them include components such as image in-tensifiers which would be normally excluded by this restriction. Thus some of the other imaging devices will not be ignored entirely. We will first review the fundamental elements and physical phenomena involved in modern electronic pickup tubes, then the relevant materials and some of the material problems and then an interesting goal yet to be achieved. REVIEW OF PICKUP TUBE PRINCIPLES In all modern television systems using pickup tubes there is an interval called the frame interval, during which the incoming radiation flux is allowed to produce a cumulative effect in the form of a stored charge pattern which is a replica of the radiation image, and a scan interval during which the stored charge pattern is converted into a video signal. The frame interval bears no fixed relation to the scan interval and may be shorter or longer. In conventional, real time television the scan interval including retrace is identical to the frame interval. Integration and storage is the key to the sensitivity of modern pickup tubes, in contrast to earlier tubes such as the image dissector. At equivalent light levels and without integration, the number of photons contributing to the video signal in the image dissector is lower by a factor approximating the number of picture elements in the displayed image, a number of order 10. Statistical fluctuations in the number of contributing photons represent a serious limitation to the attainable signal to noise ratio, resolution and contrast. As a result considerably greater light levels have to be used then in targets which integrate over the full frame period. Thus the crucial elements, common to all modern pickup tubes, are the charge storage surface and the scanning electron beam which is incident on the charge storage surface at very low energy. These are shown in Fig. 1(a). The charge storage insulator is generally very thin with a thickness of several microns or less. The surface of the insulator is held near cathode potential. The backplate potential is held at cathode potential or at a small positive voltage relative to cathode. The combination of storage insulator and backplate electrode is commonly called the "target". In the absence of incident radiation flux the electron beam scans over the storage surface depositing negative charge uniformly over the scanned part of the surface by virtue of the fact that the effective secondary

Jan 1, 1970

By R. W. Raymond

The western public domain acquired by the United States through trcaties, as the result of conquest or purchase, was invaded after Marshall's re-discovery of gold in California, by an overwhelming multitude of prospectors and miners from all parts of the world. he mineral lands of the whole Pacific slope were practically unsurveyed. Congress, disgusted with the experiment of leasing mineral lands, which it had tried for 40 years, and abandoned in 1847, enacted no laws for the management of these public mineral lands, and the pioneers made their own laws governing mining titles. These local regulations applied at first to gulch-mining in the auriferous river-beds only; and they constituted a simple and practical system. adapted to the needs and means of primitive communities—significantly called " camps." They had the means of measuring distances, but not angles; they knew no property except personal property in the form of pickaxes, pans, supplies, camp-equipage, horses or mules, and mining rights. The earliest codes which they developed expressed what might be called the law of the lariat. With the lariat they measured the distance assigned to each miner along the gold-bearing gulch—a double portion to the discoverer, and a single portion to his successors, in the order of their coming. With the lariat, they hung, after such due process of law as was available, the rascal who stole a horse, or a bag of gold-dust, or a mining claim, or killed another man without giving him fair notice and a chance to defend himself. In these pioneer codes, adopted in mass-meetings and enforced by the same authority, two features concern us most: 1. They measured mining property by one dimension only. So many feet of the gulch, held by one man, meant a distance into either bank, and a distance in depth, extending as far as gold might be found.

Jan 1, 1915

The greatest mining center in the state of Utah is the incorporated town of Bingham about twenty-five miles southwest of Salt Lake City. The principal industry of this vicinity, prior to the early fall of 1863, was lumbering and the first saw-mill in the state was built near the mouth of Bingham Canyon. Early in the fall of that year. George B. Ogilvie discovered gold and shortly afterward the first mining district in the state was organized. Some writers place the discovery of gold in the canyon in the late fifties. If this be so, however, the matter was kept extremely quiet because no mining was engaged in until after Ogilvie's discovery. Bingham was a placer mining camp, producing about one million dollars' worth of dust and nuggets from placers up and down the canyon and in Bear Gulch until early in the seventies, or about ten years after the discovery of gold, when a large body of argentiferous lead ore was discovered and soon after heavy shipments were made from a half dozen or more properties.

Jan 1, 1925

By Robert Glass Cleland

BECAUSE of the country's vast mineral resources, Alexander Von Humboldt, the great German scientist who visited Mexico, or the Kingdom of New Spain, a hundred and fifty years ago, very aptly called that country the "Treasure Chest of the World." During the three centuries of Spanish rule, mining was the principal industry of the kingdom, the largest contributor to the country's prosperity, the chief common denominator in Mexican economic life. Public revenues and private fortunes, employment and markets, agriculture and trade, charities and churches, the incentive for frontier settlement and exploration, and the funds for outfitting the expedition of colonizer and conquistador-all were dependent upon the streams of precious metals that flowed century after century from the mines of Guanajuato, Zacatecas, Real del Monte, San Luis Potosi, and scores of other minería that lay scattered everywhere throughout the land. Sonora, one of the oldest and most renowned of the frontier provinces of New Spain, had been the scene of a hundred rich strikes, sudden stampedes, and widely heralded bonanzas long before the famous and frenzied Gold Rush

Jan 1, 1952