Search Documents

1913. FRANK DAWBON ADAMS Montreal, Canada. 1921. WILLIAM CUTHBERT BLACKETT Sacriaton, Durham. England. 1923. GELAEIIO CAETANI Rome, Italy 1920. HENRY STURQIB DRINKER Merion Station, Pa, 1922. FEDERICO GIOLITTI Torino, Italy. 1906. SIR ROBERT A. HADFIELD London, England. 1928. JOHN HAYB HAMMOND New York, N. Y. 1921. FRANK WILLIAM HARBORD London, England. 1917. HERBERT HOOVER Washington, D. C. 1905. HENRI LECHATELIER Paris, France. 1931. WALDEMAR LINDQREN Cambridge, Mass. 1929. JOHN MARKLE New York, N. Y. 1921. C. MCDERMID London, England. 1913. EZEQUIEL ORDONEZ Mexico City, Mexico. 1909. ALEXANDRE POURCEL Paris, France. 1911. ROBERT H. RICHARDS Cambridge, Mass.

Jan 1, 1932

By B. G. Agnew

In evaluating fracture treatments, the need to answer such questions as "What zone or zones were actually treated?" and "What was the vertical extent of the treatment" is necessary, since determining effectiveness of the fracture treatwrent depends on knowledge of the reservoir portions stimulated and the vertical extent of the fracture system or systems. Injection of hot or cold fluids during fracturing operations will transfer heat to the surrounding formations and fracture faces mainly by heat conduction. Once injection ceases, temperature anomalies will develop opposite the zone fractured because the rate of temperature decay is less than that opposite zones heated or cooled by flow inside the wellbore or along the cement sheath. Thus, temperature surveys can he used to determine where fractures were generated outside the wellbore and to reasonahly estimate the vertical extent of the fractrires. This technique has been used successfully to evaluate over 344 fracture treatments at depths ranging from 1,500 to 15,700 ft. Examples of actual temperature surveys are presented to show how this method of fracture treatment evaluation can be used effectively and beneficially. INTRODUCTION Stimulation of producing or injection wells by fracturing is commonplace in the industry today. In evaluating these treatments, two basic questions which arise are "What zone or zones were actually stimulated?" and "What was the vertical extent of the treatment?". Knowledge of the reservoir portions stimulated and vertical extent of the fracture system or systems is vital to effect efficient and economical well completions and to assure maximum recovery from reservoirs. Not all fracture treatments are successful and many times the desired or anticipated results are not achieved. When this occurs, it is in most cases the engineer's job to determine why. The answer to this problem forms the primary basis for deciding whether to spend more money for development drilling and/or completion attempts or to forego additional expenditures to improve the particular zone. Also, knowledge of the reservoir portion actually stimulated is invaluable in planning future workovers. This is especially true in wells producing from reservoirs containing multiple porosity stringers or zones. For various reasons, all zones within a reservoir may not be perforated on initial completion with the thought of developing remaining zones through future workover operations. Because particular zones are perforated and fracturing fluid pumped down the wellbore, it cannot be assumed that all perforated zones are stimulated, and in turn drained. Occasionally, unperforated zones which are planned for future development are actually stimulated on initial completion. eliminating the need for future recompletion attempts or all zones perforated initially are not stimulated, thus requiring additional completion work to insure that these zones are adequately drained. In most cases, it is costly. if not impossible, to determine with assurance why a fracture treatment is unsuccessful after the job has been completed and the results tested. Further, unpredictable upper and lower fracture barriers. as well as possible borehole communications (cement channels), do not permit it to be taken for granted that the formation opposite the perforations is the only zone receiving the fracture treatment. Thus. evaluation of fracture treatments is necessary for efficient and prudent well completion practices and should be done simultaneously with the fracture job. Several methods have been used to locate fractured zones, all of which are based on detection of radioactive tracer materials added to either the fracturing fluid or the propping agent. These methods have been helpful in increasing knowledge of fracturing operations; however, they are seriously limited because of cost and inability to detect accurately radioactive tracer material more than a few inches away from the borehole. To develop a better diagnostic tool to pinpoint which zone or zones had actually been fractured, temperature surveys were run after fracturing with heated and cooled fluids. Significant temperature anomalies were found to exist opposite zones suspected of receiving the fracture treatment. From the analysis and examples to be shown, it can be seen that temperature surveys run in a stabilized wellbore several hours after a fracture treatment using hot or cold fluid will yield temperature anomalies which show the actual reservoir portion stimulated, the vertical extent of the fracture system or systems and a qualitative indication of the portion of fracture-fluid volume entering a given depth interval. The experience and illustrations used in this paper are based on evaluation of over 344 fracture treatments during the past three years using this diagnostic tool at depths ranging from 1.500 to 15,700 ft and fracture volumes ranging from 2.000 to 110.000 gal. Based on analyses of these temperature surveys, analyses of fracture gradients and evaluation of several open-hole packer impressions in the West Texas area,' vertical fracturing is the predominant mechanism and horizontal fractures occurred frequently, if at all.

Jan 1, 1967

By N. C. Gay, P. J. Van Der Veever

The Klerksdorp gold mining district, South Africa, experiences a relatively high level of seismicity with many seismic events of magnitude greater than 4. These large events appear to have foci close to fault planes, most of which displace the strata by several hundred metres over a wide area. To help understand the mechanism of these large mining- associated seismic events, in situ stress measurements were made at 4 sites using "CSIR doorstopper" strain relief techniques. The sites were chosen close to, or some distance from fault planes and other structures. The results show that at all 4 sites a relatively large horizontal stress is oriented approximately north- west. The magnitude of this stress ranges from 0,78-1,O of the vertical stress. A marked horizontal stress anisotropy, varying from 13-30 MPa is also present. The dominant structural features are large, north-east striking normal faults which extend across the entire length of the goldfield. Displacements across these faults vary from a few centimetres to several hundred metres. Bedding plane faults across which large displacements may occur are also common as are north and north-west striking dykes. The majority of the faults strike at approximately 90º to the maximum horizontal stress and at all sites a large compressive stress plunges in the direction of dip of the strata and fault planes. Thus a significant shear stress may act across suitably oriented planes causing them to be in a state of potentially unstable equilibrium. This abnormal stress situation would exist along the entire length of the fault

Jan 1, 1982

A Little Book on the Assaying of Gold, Silver, Copper, and Lead. Also on How to Assay and Work profitably All Minds of Metal. Complied with great care for the benefit of all mintmasters, assay masters, gold= smiths, miners, and dealers in metals.

Jan 1, 1949

ANDES, lying south of Chuquicamata and north of Braden on the western slope of Chile's cordillera, can best be described as a big well-managed copper-mining enterprise without any peculiarly outstanding features. In point of copper produced, since output started in 1927, it ranks fifth among the Porphyries, being exceeded only by its two Chilean contemporaries and by Utah Copper and Morenci in the United States. Even so, there is little to distinguish it from other properties. It does not have the phenomenally rich ore (better than 2 per cent copper) that characterizes Braden; and it is not in the same class as Chuquicamata whose ore has the excellent tenor of around 1.7 per cent, nor has it Chuqui's immense tonnage of proven ore reserves and potential ore resources. One might say the operations are standard in that there are no basic or radical departures from established practice. A letter from New York supplying me with sundry pertinent facts for which I had asked, makes this comment regarding the answer to one inquiry: "omitted because it is the ordinary equipment found in any well-run mine." The substance of that remark applies generally to the other operations, plants, and facilities. One interesting fact that helps explain this situation should not be overlooked. Until the "new" Morenci in 1942, Andes was the last of the Porphyry copper mines to come into production. It did not do much pioneering because other companies had, of necessity, charted the way in many particulars. The company was organized by the Anaconda Copper interests in 1916 to take over a, group of claims held under option by William Braden who, a few years earlier, had interested

Jan 1, 1957

Jan 1, 1924

By John Birkinbine

Mr. Neilson was born Aug. 12, 1842, at Philadelphia, Pa., where he died Dec. 30, 1906. His business career began with his graduation, in the class of 1862, from the Polytechnic College of the State of Pennsylvania. For a short time after graduation he was instructor in mathematics at the college, and then became associated with Messrs. Booth & Garrett, chemists, of his native city. In 1867 he was sent to the Adirondack mountains to care for mining interests of the late Jay Cooke, and spent about three years there, operating the forges at Elizabethtown, Essex county, N. Y. He also prepared an interesting monograph on Catalan forges and their operations. In 1868 he published a chart showing the material progress of the United States, and the cost of certain staple products during a series of years, which is believed to be the first of its kind issued in this country. In 1870 he made a trip to the Pacific Coast, prior to entering the service of the Pennsylvania Steel Company.

Jan 1, 1908

By Arthur Fleischer

THE Kalunite process? for the production of metal-grade alumina from alumina-containing ores is applicable, considered from a general point of view, to any aluminous raw material that can be converted to potassium alum or equivalent normal alum. This result of modern technology has been the subject of a continuous study and development since 1929, on a laboratory and test-plant scale, with initial emphasis on the utilization of alunite as the raw material. The research and developmental program was carried out by the Kalunite Company and its successor, Kalunite, Inc., an affiliate of the Olin Corporation of East Alton, Illinois. The process is now approaching the time for a major test in its history with the completion of construction of a plant having a capacity of zoo tons of alumina per day in Salt Lake City for the conversion of Marysvale, Utah, alunite ores to alumina and potassium sulphate. The Salt Lake Alumina Plant is a Defense Plant Corporation project. PRODUCTION OF ALUMINUM The known existence of alunite deposits, especially in the Marysvale district, furnished the motive for the original inquiry into the utilization of this raw material for aluminum production. The deposits in this region were actively explored during World War I and utilized for the production of potassium sulphate, an essential fertilizer, of which a shortage of monumental proportions then existed. Up to the twentieth century for alunite is a mineral with an ancient history-it was used in Europe and in China as a source of potassium alum. It never had been used successfully in. this country as a source of oxide for reduction to metal. Although the known reserves of this ore, which undoubtedly will be greatly expanded with a commercial outlet for this ore, are recognized to be sufficient for only a part of the present-day needs of aluminum, it has a definite place in the aluminum industry. Academically it points the way for future raw materials. The aluminum industry has undergone a remarkable growth in the past few years as a result of defense and war requirements. Its expansion in many ways has been beyond belief and prediction, both in volume and location. This wartime status of the industry has accelerated the consumption of bauxite to such an extent, that a re-evaluation of the raw material reserves for the future peacetime industry and for eventual wartime reserves is seemingly of concern. The generally accepted picture of bauxite ore reserves in the United States, especially in raw material suitable for treatment by the Bayer process, focuses attention on other possible sources of raw material of metal-grade oxide. The perspective for the development of a suitable process may have changed in the interim

Jan 1, 1944

By J. E. Forciea, R. W. Salmi

Operating and research personnel at U.S. Steel's Pilotac concentrator have evolved specifications for magnetic separators suitable for use in beneficiation of Mesabi magnetic taconite. These specifications were developed as a result of investigations into the operating and metallurgical problems at the Pilotac concentrator over a period of some ten years. This paper discusses primary magnetic separator specifications, but much of the information is also pertinent to secondary and tertiary magnetic separators. Of particular significance is the proposal of a new basis for specifying the magnetic field which includes consideration of both field strength and field gradient. Other areas of discussion include flowsheet service, operating conditions such as drum speed and pulp level, tank configuration, magnet strength including field gradient, sleeve bearing design, designation of corrosion resistant materials and other details that result in a metallurgically efficient machine that has low repair and maintenance requirements. The mechanical and metallurgical design of magnetic separators at the Pilotac plant, Minnesota Ore Operations, United States Steel Corp. has progressed from the original single-stage, belt-type machines to the present multiple-stage, drum-type units, In ten years of operation, the plant operating and research personnel, in consultation with manufacturers, have made design changes to improve mechanical, electrical and magnetic features to meet process needs as flowsheet designs developed and to incorporate new permanent magnet materials as they became available. Separator specifications were an end result of this effort. The latest specifications which were developed for the Minnesota Ore Operations' plant were not all-inclusive listings; they covered only those points indicated by plant experience. For example, magnet pole piece design and dimensions were not stated. The manufacturers were given freedom to use any design as long as the field pattern was as specified. The selection of the items to be included in the specifications was undoubtedly influenced by particular conditions at Pilotac such as composition of plant water, concentration characteristics of the ore, repair and maintenance facilities available and the research programs that had been conducted. Only the developments leading to the specifications for a primary or "cobber" magnetic separator are presented in this paper. However, the same general concepts are used to specify secondary and tertiary separators. The areas of interest discussed include flowsheet service, tank configuration, magnet design, bearings, materials of construction, and some minor mechanical details. FLOWSHEET SERVICE The primary magnetic separators in the Pilotac Concentrator flowsheet are located after the first stage of grinding as shown in Fig. 1.

Jan 1, 1965

By R. S. Shoemaker, F. W. McQuiston

SOUTH AFRICAN MILLING PRACTICE All modern South African gold plants operate primarily on the principle of exposing the gold particles in the ore by fine grinding and then cyaniding the total pulp. Although there are minor variations and occasional depart- ures from established practices among the fifty gold mines in South Africa, the normal plant operations proceed as follows. After removal of waste rock by hand sorting (15Y0 on average) the ore is crushed in cone crushers to minus 1/2 inch and then ground to approximately 75% minus 200 mesh by milling with either rod, ball or pebble mills as primary units and pebble mills for the secondary grind. Classification in both circuits is almost invariably conducted with 20" cyclones of 30" or larger diameter. Gravity concentration in the milling circuit followed by barrel amalgamation of the concentrates is practiced in 70Y0 of the plants, particularly where the ore grade is high. A slightly better overall recovery is obtained than with direct cyanidation, but additional handling is involved. Johnson cylinder s , plane tables or belt concentrators, all lined with suitable types of molded rubber riffles, are used for this purpose. At all mines, cyanidation is the main process, usually conducted by continuous treatment in Pachuca tanks and pulp separation with rotary drum filters. Cyanide solutions contain about 0.0 1570 NaCN and require a protective alkalinity of 0.02070 CaO. Precipitation of the gold from cyanide solution is exclusively by zinc dust and lead nitrate using the Merrill-Crowe system in conjunction with Stellar pressure filters. The zinc precipitate is smelted, generally after a preliminary concentration by sulfuric acid, in electric furnaces, mostly submerged arc types, with a silica and borax flux, yield- ing a bullion of 8870 gold, 9% silver, and 370 base metals. The gold content of the ore varies between 0.20 and 1.0 oz Troy per short ton and extraction efficiency ranges from 9570 to 9870. In general, 4070 of the gold output is recovered by amalgamation and 6070 by cyanidation; but in some cases, it is entirely by cyanidation. Flotation has not been adopted for gold extraction as it has not proved as efficient as cyanidation. It is, however, often applied to ores containing higher than 1% sulfur for the recovery of pyrite for sulfuric acid production. On the eastern side of the Witwaters rand Basin, "run-of -mine milling” was introduced in 1960 and in three of the four mills in this area both sorting and crushing have been eliminated. The ore received from the shafts is conveyed to storage silos and then fed by Williamson automatic feed controllers to pebble mills ranging from 12 to 14 feet diameter, and 16 to 20 feet long. The pebble mills operate in closed circuit with 42 inch cyclones and the slime produced is thickened and cyanided in the conventional manner. No selective

Jan 1, 1975

By T. K. Prentice

The January-February number of the Journal of the Chemical Metallurgical and Mining Society of South Africa, 1943, is made up entirely of a discussion of Ball Wear in Cylindrical Mills. Following the principal paper by T. K. Prentice are several remarkably pertinent and carefully prepared discussions. Few persons in this country would be likely to see this publication, and since the information presented is new and of current interest, it seems desirable to abstract and review this publication for the benefit of the members of the A.I.M.E. The purpose of the investigation is stated in the first two paragraphs of Prentice's paper, as follows: Early in 1941, The Chamber of Mines Steel Products, Limited, initiated a series of tests under semi-working scale conditions to determine, if possible, those physical and chemical properties of a ball which make it resistant to wear when used in a cylindrical mill as a grinding medium, with the primary object of incorporating those beneficial qualities in the balls being produced at their works. This paper describes the tests carried out and discusses the results obtained. From these results it was possible to formulate a new theory relating to ball wear in cylindrical mills. This theory is presented in the second portion of this paper. Practical Ball-mill Tests in a Cylindrical Mill Part I of the paper begins with a discussion of the methods used for the manu- facture of grinding balls in South Africa. The following paragraph is of particular interest. The cast steel ingots, 4¼ in. square by 3 ft. 6 in. long, are re-heated in a gas-fired sloping stationary-hearth furnace and then rolled in a six-pass continuous mill into 25/8 in. round billets. Some of these billets are then removed and cut into suitable lengths for forging into 4 in., 3¼ in. , 3 in. or 2½ in. balls by means of three Drop and two Beche hammers, but the greater number, whilst still at about 1,000, pass directly into a set of scroll rolls which produce, in an ingenious manner, finished 3 in. balls direct from the 25/8 in. billets. Except in special cases, all balls are allowed to cool in the atmosphere and are not water quenched. Details of the Tests In order to enable the reader to evaluate properly the results and conclusions in the rest of the paper and in the discussions following the paper, most of the information presented by the author under this heading is quoted: The testing unit was a nominal 30 in. diameter and 18 in. long centre discharge Denver Ball Mill. The ore pulp to the ball mill comprised a small portion of the normal feed to one of the fourteen City Deep 5 ft. 6 in. X 22 ft. tube mills, and the grinding media consisted of the balls under test plus other balls to give the desired load. The running time of the test-mill was divided into approximately equal periods of five days 13½ hours each. The usual procedure was to examine and make up the load

Jan 1, 1947

By Jr. D. C. Williams, D. V. Carter

The four new oil-field discoveries made in the East and East Central Texas districts during 1941 were the East Long Lake field, Anderson County; Pickering field, Shelby County; Pleasant Grove field, Rusk County, and Tri-Cities field, Henderson County. The discovery of oil production in the Pettit lime of the Lower Glen Rose was made in the Groesbeck (Barron) field in Limestone County and the Willow Springs field in Gregg County. Important extensions were made to the Pittsburg field, in Camp County, the Chapel Hill field, in Smith County, and the Hawkins field, in Wood County. The Hawkins field was extended sufficiently to more than double the number of proved surface acres. As usual the East Texas field led the district in the number of completions for the year. The second most active field during the year was the Hawkins field, with 250 new wells completed. The third most active was the Long Lake field, in which 50 wells were completed. Approximately 964 wells were completed in the district during 1941. Production and Probation The district is credited with having produced 163,566,695 bbl. of oil and distillate during the year. This represents a decrease of 4 per cent from the 170,424,685 bbl. of oil and distillate produced during the preceding year. The production of 130,378,620 bbl. of oil and distillate from the East Texas field represents 79.7 per cent of the total production of the district; that is, 6.3 per cent less than the production for the year 1940, The district had an estimated basic daily allowable of 614,982 bbl. of oil on Dec. 31. Approximately 33 per cent of the state's annual production was produced in the district, compared with 34.9 per cent for 1940. Since the majority of the fields in this district are subject to proration, any change in the annual production is attributable largely to changes in proration schedules and number of shutdown days. Fields subject to shutdown days were closed in for 113 days during the year, with the exception of the East Texas field, which was shut down 111 days. An order was promulgated by the Oil and Gas Division of the Texas Railroad Commission for encouraging the disposal of salt water and reservoir-pressure maintenance in the East Texas field. Discoveries Tex Harvey Oil Company'sNo. I S. E. J. Cartmel was completed as the discovery well for the East Long Lake field, Anderson County. Production was found in the Woodbine sand, the horizon from which the Long Lake field produces. The Pickering field, Shelby County, secures its production from the Nacatoch sand, found at an approximate depth of 1510 ft., in A. E. McKiernan's No. I, Pickering Lumbering Co. This field is in an area near the state line in which a number of relatively unimportant and

Jan 1, 1942

By J. M. Roberts, N. Brown

The stress-strain behavior of zinc single crystals was measured over a strain range of 10-6 to 10-2. The phenomenon of macroyielding was observed in detail and plastic strains were detected at almost zero-stress. Closed hysteresis loops were observed during loading and unloading in the strain region of about 10-5. From the hysteresis a frictional stress on the dislocation of about 6 psi was obtained. A preliminary analysis indicates that impurities are primarily responsible for the friction. Nonelastic Strains as much as 10 -4 were recovered depending on the amount of prior deformation. Part of the recovered strain occurs instantaneously upon unloading and the remainder occurs at zero stress. The time dependence of the recovered strain was measured. THIS investigation is concerned with the details of plastic deformation preceding the ordinary yield point as measured with the usual strain sensitivity of about 10-4. The approach leads to internal friction observations in the hitherto neglected frequency range below 10-1 cycles per sec. It is believed that if the phenomenon of macroscopic yielding is to be understood, then the stress-strain curve in the neighborhood of the macroyield point should be greatly magnified. It may then be possible to determine whether macroscopic yielding is a unique event or whether it is a process which begins gradually at a lower stress. In the case of low-carbon steel a unique event obviously occurs at the macroscopic yield point as indicated by a drop in the load, but copper appears to exhibit a gradual transition from the elastic to the plastic state. In zinc the yield point is rather abrupt although the data indicates that some plastic deformation precedes large scale yielding.' One of the purposes of this investigation is to determine whether there is an abrupt transition from the preyield microstrain region to the region of macroscopic deformation. Such a rapid transition would support the concept that there is a critical stress for yielding. The concept that yielding is a unique event associated with such phenomenon as activating a Frank-Read source, freeing the dislocation from solute atoms, dislocations cutting through dislocations, or dislocations moving freely by one another, has been expounded widely on theoretical grounds. It is hoped that highly sensitive measurements of strain in the neighborhood of the macroscopic yield point will shed some light on the event known as the "Yield Point". EXPERIMENTAL METHOD 1) Specimens—High-purity zinc was cast into spherical graphite moulds in air and grown into spherical single crystals by the Bridgman method under a positive pressure of Argon gas. Spectro-graphic analysis of cleaved sections from four crystals showed a purity of 99.994 pet Zn. The specimens were acid machined with an 1/8 in. gage section in a form similar to those used by Parker and co-workers.2 Bausch type grips were fastened to the specimen by Epon VI adhesive. The specimens were oriented so that only [1120] (0001) slip occurred. Fig. 1 shows two of the specimens in the grips. Prior to each test, the gage section of the specimen was given a concentrated HNO3 chemical polish followed by alcohol rinsing and air blast drying. 2) Test Method- The shear tests were performed on an Instron testing machine and the experimental set-up was made very "hard". Strain could be measured to a sensitivity of 10 -6 by means of a capacitance gage extensometer. The design and calibration of this type of extensometer to measure microstrain, as applied to pure shear and tensile tests of metals, will be the subject of a separate paper—therefore, only a brief account will be presented here. The method essentially consists of attaching a

Jan 1, 1961

By T. Imaizumi

Covering the whole scope of the MMIJ activities, i.e. geology and exploration, mining, mineral processing, and metallurgy, the technical innovations and improvements since 1972 were reviewed. Special references were made to the MMIJ Research Committees which were subsidized by the Japan Mining Promotive Foundation, in connection with those activities.

Jan 1, 1976

By P. Martignan

UNTIL quite recently, Alsace was the only district in France where petroleum could be found in somewhat industrial quantities. The Pechelbronn fields produce, however, only about 80,000 tons a year, which represent approximately one-eighth of the domestic consumption. Much research work has been done in Alsace to find the prolongation of the Pechelbronn fields, but instead of oil the drillings revealed the existence of large deposits of potash. This can be easily explained when one remembers that the Pechelbronn oil is of the Oligocene period, and that in the Alsatian stratification the Oligocene lies immediately on the Keuper, i. e., on the strata that originate from a period during which the largest salt and potash deposits were constituted. Before the war, and mostly at the end of the last century, some wells were drilled in. various districts of France where some analogies could be found with the Alsatian geology, the borings being mainly made in the Triassic and Tertiary beds. They led to negative results. After the war, the growing importance of oil urged the necessity of resuming the explorations. But it. is our belief that this was greatly facilitated by the enacting of new legislation, which is embodied in the Mine Act of May 16, 1922.

Jan 3, 1925

CONTENTS PAGE Need for Research in Foundry Pig Iron. By Richard Moldenke. (With Discussion) 1 Carbon Characteristics of Copper-bearing Pig Iron. By W. B. Coleman. (With Discussion) 12 A Pig Iron, Low in Total Carbon, is in Demand for Use in Various Industries. By Enrique Touceda. (With Discussion) 24 Carbon in Pig Iron. By Ralph H. Sweetser. (With Discussion) 28 Second Session (Discussion) 37 Need for Research in Foundry Pig Iron BY RICHARD MOLDENKE,* WATCHUNG, N. J. So FAR as the quality of the product is concerned, the history of the production of pig iron for foundry purposes is one of constant retrogression. The steps in this deterioration began with cold-blast charcoal pig iron, then anthracite iron, coke iron; then gradually warm to hot-blast coke iron, with the charcoal furnaces also heating their blast to get greater tonnages, and finally the present-day hot-blast coke irons with scrap additions to the ordinary burden that, according to one European report, have gone as high as 65 per cent. Parallel with this quality retrogression is the enormous increase in furnace tonnages from about 15 to over 1000 tons per day in exceptional instances of modern practice. The key to this situation is economic pressure. The effect is a growing differentiation between furnace production for gray iron and malleable foundries and, for the

Jan 1, 1927

By T. V. Falkie, Robert Stefanko

Coal Mine Health and Safety Act in December 1969, the most comprehensive law in the history of the coal mining industry went into effect. Hardly anyone will quarrel with the philosophy that all miners in the United States should be afforded equal protection under the law irrespective of the state in which they reside. Furthermore, it appears contrary to any sound judgment that a competitive advantage should appear to accrue to a mine operator because his operations are located in a state with less stringent (and costly) health and safety laws Yet it is recognized that the quality of state mine laws and inspection agencies has been extremely variable. Why, then, should there be such resentments over the passage of the Act? The Act was written In the highly emotionally charged atmosphere following the Consol No. 9 disaster: the technical expertise within the industry was discredited and largely ignored; and those directly involved in the writing of the Act were non- technical and largely nonmining people. The result was that the law incorporated certain requirements that were impossible to meet (automatic brakes are the classical example) and certain parts that were too ambiguous and consequently open to interpretation.

Jan 1, 1971

AN economist at MIT provided Americans with myth destroying information which should prove effective against the gentlemen of the extreme left. For a number of years they have charged that a small number of companies in each industry has been grabbing more and more of the industry's business. M. A. Adelman has shown that the concentration of business in the hands of big corporations has not shown any sign of growth during the last 50 years. Quite the contrary, there has been a slight decline in this concentration, according to Adelman. There are more small companies per thousand population than ever before. Bearing this out is the fact that International Harvester is now doing 41 pct of the possible market against a former 85 pct; American Can Co. has dropped from 90 pct to 50 pct; American Smelting is down to 31 pct compared with 90 pct; and lastly, U. S. Steel which has plummeted from 65 pct to slightly more than 30 pct of the steel market. Declines of the same proportions have hit big companies in other industries. Price cuts on Detroit's 1953 automobiles indicate that even among the biggest competition is still one of the most important household gods. Big business is still slugging it out for the attention of the American consumer. It's a battle which can only have one result-benefit to the man who buys.

Jan 1, 1953

By F. M. d’Heurle

Films of molybdenum have been prepared by sputtering onto oxidized silicon substrates. The resistivity. lattice parameter, orientation, and grain size were studied as a function of substrate temperature and substrate bias. Under normal sputtering conditions, the resistivity of the films was found to be quite high (600 x 10 ohm-crn). However, with the use of the negative substrate bias of 100 v and a substrate temperature of 350°C, films weve produced with a resistivity of ahout twice that of bulk molybdenum. The lattice parameters measured in a direction nornzal to the surface of the films weve found to be gveatev than the bulk value. This was interpreted as being at least partly due to the presence of compressive stresses. The effects of annealing in an Ar-H atmosphere were studied in terms of diffraction line width, lattice parameter, and resistivity. BECAUSE of its relatively low bulk resistivity (5.6 x 106 ohm-cm)' molybdenum is potentially interesting as a thin-film conductor in integrated circuits. An additional feature which makes it attractive for this purpose is its low coefficient of expansion (5.6 x KT6 per "c),' which is fairly well matched to that of silicon (3.2 x 10 per c). It is possible to deposit molybdenum films by evaporation but generally films produced in this manner have a high resistivity. In order to achieve resistivities close to bulk value, Holmwood and Glang found it necessary to operate in a vacuum of about 107 Torr and to maintain the substrates at 600 C during film deposition. Sputtered molybdenum films have been examined by Belser et a1.7 and, recently, by Glang et al.' This paper describes the results of an attempt to extend some of that work and examine the effects of annealing and getter sputtering on the physical and structural properties of the films produced. SPUTTERING APPARATUS AND PROCEDURE The apparatus used for most of the film sputtering work described here consisted of two "fingers" serving as anode and cathode, respectively, which were mounted within an 18-in.-diam glass chamber. A liquid nitrogen-trapped 6-in. diffusion-pump system was used to achieve a vacuum of about 1 x 107 Torr within the chamber prior to sputtering. The essential features of the equipment are shown in Fig. 1. Cathode and anode fingers are stainless-steel tubes isolated from the top and bottom plates by Teflon collars. In order to limit the discharge to the space between anode and cathode, each finger is surrounded by an aluminum hield, at ground potential, having an internal diameter 18 in. larger than the outside diameter of the finger. The cathode and anode fingers are 6 and 4 in. in diam, respectively. A 116-in.-thick sheet of molybdenum is brazed with a 10 pct Pd, 58 pct Ag, 32 pct Cu alloy to a copper disc which is mounted by means of screws and a large 0 ring onto the lower end of the cathode finger. The disc is cooled during sputtering by water circulation inside the finger. The use of several feet of plastic tubing for the water input and outputg reduces leakage to ground to less than 1 ma when the cathode potential is raised to 5 kv. The upper end of the anode finger is terminated by a brazed-on copper block. A variety of specimen holders can be easily mounted on the upper face of this block. Substrate heating or cooling is achieved by use of an appropriate unit attached to the lower face of the same block. Heating is achieved by means of cartridge-type heaters and cooling by copper coils fed with forming gas under pressure. The inner chamber of the specimen finger constitutes a small vacuum chamber of its own which is evacuated by an auxiliary mechanical pump in order to limit heating element oxidation and heat transfer by convection currents. An advantage of the finger arrangement is the absence of cooling and heating coils and wires within the main chamber. The stain less-steel shutter is useful to establish a discharge for cleaning the cathode at the beginning of each sputtering run. Water cooling of the shutter reduces heating and the out-gassing of impurities which might condense on the nearby substrates. Unless otherwise specified, the substrates used in these experiments were 1-in.-diam oxidized silicon wafe:s, 0.007 in. thick, having an oxide thickness of 6000A. The substrate holders were large copper discs onto the surface of which a number of molybdenum discs, 116 in. thick and 78 in. in diam, were brazed. The wafers were clamped to the molybdenum discs

Jan 1, 1967

By Leonard D. Jaffe

In recent years, the advantages of tempered martensite as a microstructure for steel parts have been well established. For parts that must not fracture brittlely when loaded at high rates, at low temperatures, or under conditions of combined stress, tempered martensite is especially desirable. One of the factors that determine whether a steel part will have a martensitic structure after heat treatment is the hardenability of the steel. Despite the large amount of recent research, there are still many unsettled basic questions concerning hardenability and its relation to chemical composition, and, indeed, considerable disagreement among investigators in the field. Much of the uncertainty that beclouds the existing knowledge of hardenability arises from the fact that hardenability is still a wholly empirical concept, and has not been quantitatively related to the more fundamental knowledge of isothermal decomposition of austenite. Hardenability is, essentiaily, a measure of the time required for small percentages of austenite to decompose, during continuous cooling, to pearlite, bainite, proeutectoid ferrite, or proeutec-toid carbide. In the practical heat-treat- ment of steel, also, the decomposition of austenite is usually not isothermal but rather during cooling, or, in general, is not at a single constant temperature. Thus, both hardenability and practical heat treatment involve anisothermal decomposition of austenite. In a previous publication1 the author and his collaborators outlined the principles that govern the relations between isothermal and anisothermal decomposition of austenite, and reviewed the experimental information available in 1945. To avoid repetition, familiarity with that article (Paper I) will be assumed, and attention given primarily to work carried out or published since 1945. The method generally employed was explained in Paper I: anisothermal transformation is studied through investigation of the effect of holding austenite at one temperature upon its subsequent decomposition at another temperature. Both temperatures are below the stability range of the austenite. This paper is confined to studies in which only a small amount of transformation occurred at the first temperature. This is the only case of importance in practical heat treatment when an essentially martensitic structure is sought. Materials and Procedure It was necessary to use different steels for the studies involving proeutectoid ferrite and for those involving proeutectoid carbide, beeause the two constituents have not been found to form in the same steel. Several steels were tried and rejected

Jan 1, 1949