Search Documents

By F. G. Miller

Earlier studies of the mechanism of flotation showed that coal flotation products are contaminated by composite coal and mineral particles. The mineral matter of these particles has the dual effect of increasing the specific gravity and decreasing the coal surface of the particle available for bubble attachment. The present study showed that these particles are more loosely held in the froth column than the high grade coal particles, especially in the coarser sizes. Consequently, it is possible in the laboratory to produce a secondary concentration of the product by sprinkling the froth product with water to wash these loosely held particles from the froth during formation and recovery. To improve coal flotation, Bethlehem Steel Corp.'s research department has been working on a number of related problems based on both physical and chemical factors. The ideal is of course full understanding of the interrelated effects of both sets of factors. However, detailed studies1 of each physical factor have produced immediately usable results in commercial coal flotation and are providing the basis for our current work on the effect of chemical factors. Since these detailed studies provided the basis for the present investigation of froth sprinkling, their key results are highlighted here. For example, for a highly floatable bituminous coal, particle floatability was shown to be directly related to the percentage of coal surface available for bubble attachment and inversely related to particle mass. The data also underscored that in a given size range the addition of mineral matter to a particle makes flotation more difficult both by adding to the mass of the particle and by decreasing the amount of coal surface available for bubble attachment. Size also affects particle floatability in that as the size of particles of a given specific gravity increases, mass increases and the ratio between coal surface area and mass of the particle decreases. Flotation tests showed that any recovery of the coarsest particles in a coal feed is accompanied by progressively higher recovery of finer and finer particles. Consequently, fine high-specific-gravity particles are recovered with the coarse good coal. As a result, when the entire 14 mesh x 0 size range is processed by froth flotation, the good coarse coal is contaminated with high-specific-gravity fines. It is the small quantities of these fines that must be rejected from the froth product if flotation efficiency is to be increased above its present level. These principles and findings, together with work by Professor V. I. Klassen,' led to the froth sprinkling investigation reported in this paper. Working with Russian coals, Klassen had shown that froth sprinkling washes loosely held refuse particles from the froth and compensates for the water lost in the upper froth layers and increases its stability. As a result, the coal particles are retained in the froth and the loss of coarse coal from the froth is prevented. Decreases in ash of 0.1% to 1.5% were reported by Klassen. Working with a 28 mesh x 0 American coal, the author of the present paper found that single-stage flotation coupled with froth sprinkling produced a product comparable to that obtained by the more expensive method of roughing and cleaning.3 The investigation reported in the present paper expanded study of the effect of froth sprinkling to include each of the standard size fractions of a bituminous coal. The main findings are as follows: (1) For those size fractions between 48 mesh and 150 mesh, froth sprinkling produces a marked reduction in both sulfur and ash. In the case of those sizes coarser than 48 mesh, while this reduction is not as significant, the additional benefit of shorter retention time is still a plus for froth sprinkling. Furthermore, when froth sprinkling is coupled with normal fast flotation, the product purity approaches that obtained by starvation reagent feeding, i.e., gradual feeding of flotation reagent to float the recoverable coal from the pulp slowly in several increments. The specific results for these two size groups are: (a) 14 x 48 Mesh. By using froth sprinkling with fast flotation, product sulfur can be reduced to a level

Jan 1, 1970

By J. L. Kenty, J. P. Hirth

The concept of a critical super saturation, below which the nucleation rate is essentially zero and above which it is essentially infinite, is discussed with reference to vapor-solid nucleation. The necessary and sufficient conditions deduced for observations of this type of behavior are: 1) the nucleation rate must exhibit a sharp dependence on super saturation, 2) the growth rate must be sufficiently large that nuclei become observable in the time period of the experiment, and 3) the number of highly preferred nucleation sites must be small. Experiments reveal that the nucleation of silver on sodium chloride is visually detectable at all experimentally accessible super saturations and does not exhibit critical nucleation behavior. Failure to observe a critical super saturation is attributed to the insensitivity of nucleation rate to supersaturation as a consequence of the particular values of the contact angle and the surface free energy for this system. THE concept of a critical supersaturation, below which the nucleation rate is essentially zero and above which it is essentially infinite, arises naturally in homogeneous nucleation theory. Experimentally this type of behavior has been found by Volmer1 and others for water and other low surface tension liquids, as reviewed by several authors.2'3 The same type of behavior has been predicted and observed for heterogeneous nucleation of solids by Yang et al.4 and others,596 as also recently reviewed.2,7,8 In the work reported here on the heterogeneous nucleation of silver on NaC1, however, no critical super-saturation was found. Similar observations have been made recently for other systems.9-11 These results led to a reexamination of nucleation theory which revealed that there are conditions for which critical behavior is not predicted, either for homogeneous or heterogeneous nucleation. Although heterogeneous nucleation is of primary importance in this paper, some insight into critical behavior for such a case can be gained by considering homogeneous nucleation. Accordingly both types of nucleation theory are reviewed briefly. The requisite conditions for critical supersaturation behavior are then considered. The experimental results for the nucleation of silver on NaCl are presented and interpreted in terms of the theoretical presentation. REVIEW OF NUCLEATION THEORY There are essentially two approaches to nucleation theory, the so-called classical theory involving the concepts of bulk thermodynamics, and the statistical mechanical theory in which nuclei are regarded as macromolecules. The classical theory is based on the work of Volmer and Weber12,13 and Becker and. Doring14 and has been extended by Pound et al.15 The crucial assumption in the classical theory is that the small clusters or nuclei can be characterized by the same thermodynamic properties as those of the stable bulk phase. Thus, the nuclei are assumed to have a surface free energy, y, and a volume free energy of formation (relative to the vapor phase), ,, identical to that of the bulk. For deposition under low super-saturation conditions, the nuclei are large and this assumption is satisfactory. However, in many cases of interest, the nuclei contain only a few atoms and this assumption is highly questionable. The statistical mechanical models originated, for the specific case of a dimer as the critical nucleus, with the work of Frenkel16 and were extended later to larger sizes by Walton,17,18 Hirth19 and, more recently, Ht Zinsmeister. These models describe the nucleus in terms of a partition function, the estimation of which is tractable for clusters of 2 to 10 atoms, but extremely difficult for clusters larger than 10 atoms. Although the classical and statistical mechanical models are expected to apply for the limiting cases of large and small nuclei, both are uncertain for intermediate sizes. In this paper we shall treat only the classical model, recognizing that it is exact only for large nucleus sizes and regarding it as a phenom-enological description for small nucleus sizes. When analyses of experimental data using bulk properties show the nucleus size to be small, the resulting parameters should be regarded as largely empirical parameters describing the relative nucleation potency of the system. Considerable justification for the continued use of classical theory is provided by its general success in predicting nucleation behavior as a function of supersaturation and temperature. We emphasize that the qualitative features of the statistical mechanical models, particularly the critical super-saturation behavior that is central to the present work, are the same as those of the classical model. Of course, potential energy terms and surface partition functions replace the volume and surface energy terms of the latter model. The most recent versions of classical nucleation theory have been extensively reviewed.2,3,7 so that only the results are presented here. For homogeneous nucleation of a condensed phase from the vapor phase, the volume free energy change is ?Gv=vrT = =^ln£ [1] where v is the molecular volume of the condensing species. The supersaturation ratio,

Jan 1, 1970

By D. H. Yardley

Diversion of the American Falls of Niagara to permit investigation of ways and means to stabilize the falls while retaining or improving its natrual attractiveness is the geoengineering work that has received greatest public attention this year. The falls are re- treating slowly as rock falls occur while talus de- posits at the base have increased in size. One of the noteworthy questions is whether the talus should be removed-i.e. is it providing support to the base, and so what will happen if it is removed? Certainly the appearance would be improved if the talus were taken away. Geoengineering studies involve mapping of joints, stress measurements, core work and rock sampling and testing, Present work will provide data and interpretation for design of a long term stabilization system, Once basic information is obtained, water will be returned to the normal channel until such time as the detailed design is decided upon. The falls will then be diverted a second time while necessary work is performed. A number of site-environmental studies were carried out for the location of nuclear power plants. These projects involve geology, foundation engineering, hydrology, seismology, meteorlogy, marine geology (in some cases), rock mechanics and occasionally blast monitoring. In one case (investigated by Dames & Moore) the site area was underlain by caverns in limestones at shallow depths but with no surface expression. The geotechnical problems consisted of determining proper spacing of drill holes to locate caverns. Spacing was dependent on the smallest size of cavity that could constitute a support-stability problem for the plant. The finite element method of analysis was used to determine stress conditions around cavities of various size and depths, to assist in determining critical parameters.

Jan 1, 1970

By R. P. Harvey, J. E. Walstrom, A. A. Brown

In view of the large number of wells directionally drilled from offshore platforms and urban drillsites, greater interest is being focused on the directional survey and on the uncertainty inherent in calculating the position of the bottom of the hole, or other benchmarks in the wellbore. Of the two methods presented here for evaluating this uncertainty, the first is analytical and uses the principles of probability and statistics. The second method uses Monte Carlo simulation to generate a pattern of the scatter of possible bottom-hole locations. Both methods are based on a model for which the usual assumption is made that the curvilinear axis of the wellbore is adequately represented by a large number, M, of linear segments joined end to end from the top to the bottom of the hole and closely following the course of the hole. The errors due to this approximation are assumed to be negligible and are not studied here. One form of the model is to consider that for a given hole there exists a perfect set of data describing it, of the above form. Each linear segment has an angle of inclination with the vertical 7, in radians, an azimuthal angle from true north xi in radians, and a length Si, in feet. The subscript variable, i, extends from 1 to M. Each of the M linear segments representing the axis of the wellbore has three components in the X, Y, and Z directions. These components are calculated from the equations: The bottom-hole coordinates as determined from the reference set of data for the wellbore are given by the following for i = 1 to M: X=SX, Y = Sy, Z=SZ; . (2) A directional survey instrument, lowered into the wellbore to the M segments, or stations, measures the values of the 7; and the 3,. In general, because of errors from various sources, the resulting angular measurements will not be precisely equal to the 7" and xi. Random variables l, and Ai are therefore considered with associated probability density functions fi(li) and gi(Ai), respectively, which represent the distributions of potential survey measurements for this hole. Since it is assumed that the values Si are accurately measured they are treated deterministically. The random variables corresponding to the surveyed bottom-hole coordinates are given, for i = 1 to M, by:

Jan 1, 1970

By Shiro Ban-ya, John Chipman

Using the same experimental method previously described, the activity of sulfur in a number of quaternary and more complex liquid iron alloys at 1550oC is determined. A "cross-product term zj.zk is determined for each of the quaternary alloys to take account of the mutual effects of the combinalion on the indi-vidual contributions to In 5 The interactiotl coefjicienls delermined for ternary solutions and cross-pvoducl coefficierlts from the quaternary systems are used to estimate the activity coefficient of sulfur in more complex alloys. OUR recent papers 1,2 have described new determinations of the activity of sulfur in Fe-S binary and Fe-S-j ternary solutions, but the practical applications of these data require the estimation of activity of sulfur in more complex systems. Previously, Sherman and chipman3 devised an approximate method for calculating the activity of sulfur in complex systems by summing the contributions to the logarithm of the activity coefficient of each element in the alloy. This procedure is more successful, as one of us has pointed out,4 when the concentration variable is taken as zs = ns/(nFe — nS t CLJ~ nj) rather than the conventional atom fraction x~ = nS/(nF, + nS + Enj). In the former definition, which is based on analogy to interstitial solutions, the value assigned to uj is normally +1 for metallic and -1 for nonmetallic elements." In addition, however, the effects of mutual interaction between alloying elements must be considered for the accurate estimation of the activity of sulfur in more complex systems. The purpose of this investigation has been to devise a more reliable method for estimating the activity coefficient of sulfur in nmIticomponent iron alloys. The measurements were carried out on some quaternary systems Fe-S-j-k for combinations of silicon, chromium, nickel, cobalt, molybdenum, and tungsten. Manganese was not included since the experimental method has been found unsatisfactory for volatile, sulfide-forming elements. The experimental method was the same in every detail as described previously. 1,2 The concentrations of sulfur, silicon, chromium, and copper in the quenched metals were determined by chemical analysis but those of nickel, cobalt, molybdenum, and tungsten were calculated from charged amounts. Iron sulfide was included in the charges in amounts estimated to furnish approximately the final sulfur content. CALCULATION W2 have shown2 that when zs and zj are the concentration variables in a ternary Fe-S-j solution the logarithm of the activity coefficient S = a~/zg is a linear function of the variables as and aj defined as follows:

Jan 1, 1970

By Robert L. Bates

On April 2 and 3, 1970, more than 100 geologists attended the Sixth Annual Forum on Geology of Industrial Minerals at Ann Arbor, Mich. After this brief appearance, the Forum apparently ceased to exist- but it didn't really, and another spring will see it again in action, in another corner of the country. The organization might be characterized as the country's largest permanent floating conference on the geology of industrial minerals. What is the Forum, where did it come from, and what is it up to? The idea originated in 1964 with a small group in the Department of Geology at Ohio State University, Columbus. This group felt that a forum was needed for the exchange of geologic information on industrial rocks and minerals. They envisioned an approach-which has subsequently been adhered to--that would be dominated neither by geological academics interested in theoretical problems nor by practical engineers concerned with processing large tonnages of rock. It was proposed to focus attention on the middle part of the spectrum, especially on practical problems of geological occurrence and how these problems affect extraction and use. In terms of the standard rock-products flow sheet, which starts with a truck unloading into the primary crusher beneath the words 'from quarry,' it was proposed to focus geological attention on what is beyond the primary crusher, out in the quarry.

Jan 1, 1970

By M. S. King

In the design of foundations for large structures and of safe mine openings in rock, the results of laboratory and small-scale in-situ tests are often used to predict the behavior of the material as a whole. For reasons of simplicity in these analyses, the rock is usually treated as an ideally elastic, isotropic material. It has been observed, however, that most rocks are neither isotropic nor ideally elastic. This observation is particularly true for rocks subjected to low confining pressures. It is therefore necessary to investigate further the effects of anisotropy and nonlinearity on the mechanical behavior of rocks. When small differences in stress and strain only are involved, the rock may be treated as an elastic material. The elastic constants for such a material subjected to a particular confining pressure can be calculated from the classical theory of elasticity for different degrees of anisotropy. There are two experimental methods by which this can be done: first, from measurements of static stress-strain relationships; second, from elastic wave velocities measured in the rock. The former yields the static elastic constants, and the latter, the dynamic constants. The static constants will be equal in magnitude to the corresponding dynamic constants only if the rock is ideally elastic. Walsh and Brace1 have reviewed theoretical studies of the elasticity of rock considered as a material containing pores and cracks. They re- ported that the presence of sharp, narrow cavities at low confining pressures strongly influences the mechanical properties of a rock. A considerable reduction in magnitude of elastic moduli is associated with the presence of inhomogeneities such as cracks or joints. The elastic properties appear to approach those of the uncracked material in magnitude as the cavities are closed by higher pressures. Walsh and Brace

Jan 1, 1970

By Å. Sterten, R. Tunold, J. Brun, K. Dalatun

c axis compression behavior of beryllium single crystals at three purity levels under hydrostatic pressures up to 27 kbars was determined. Extensive non-basal slip, observed by two-surface trace analysis and transmission electron microscopy, occurred under a hydrostatic pressure of about 12 kbars (175 ksi) for the high-purity (twelve-zone pass) material and at about 19 kbar (275 ksi) for the lower-purity (zone-leveled) material. Prismatic loops with a (c + a) Burgers vector were observed in association with second-phase parti- A principal factor limiting the use of beryllium is its brittle behavior when tested at the usual strain rates (E = 10-4 sec- 1) at temperatures below about 200°C and under impact conditions at temperatures in excess of 200°C. It has been proposed' that the brittle-ness of beryllium is associated with the lack of a sufficient number of independent slip modes and the absence of a slip mode with a Burgers vector out of the basal plane [presumably (c + a) pyramidal slip mode] and to the ease with which beryllium cleaves on the basal and second-order prism planes. The absence of pyramidal slip has been attributed to a high Peierls-Nabarro stress associated with the motion of dislocations with a (c + a) vector and the ease with which cleavage occurs on the basal and second-order prism planes. The experimental evidence in support of the proposed explanation for the brittleness of beryllium is far from complete; for example, that the ductile-to-brittle transition in polycrystalline beryllium is associated with the operation of profuse (C + a) slip has not been unequivocally established. The occurrence of (c + a) slip ({1122}(1123)) has been experimentally established2-5 under conditions where basal and prism cleavage are restricted in a c axis compression test. In these investigations (C +a) slip was found in high-purity beryllium single crystals tested in c axis compression* at 200°C and in Be-4.4 pct Cu and Be-5.2 pct cles in the lower-purity materials tested. The loops were related to surface "extrusions" observed on many of these same specimens. Nonbasal dislocations operating on (1122) planes with a (c + a) Burgers vector were observed. The presence of c and a dislocations together with (c + a) dislocations suggests that the (c + a) dislocations dissociate presumably on unloading or after failure of the test crystals to c and a dislocations. terial, (c + a) slip has only been observed near the the fracture4 surface in room-temperature c axis compression tests. Fracture in these tests occurs without measurable plastic flow, as determined with a strain sensitivity of 10"6. Since it has been shown for many metals that the application of hydrostatic pressure suppresses fracture,?-' it was felt that studying the behavior of unalloyed beryllium single crystals stressed in c axis compression under a hydrostatic pressure would reveal whether (c + a) can occur if fracture was prevented, and that it might elucidate the role of (c + a) slip in the ductile to brittle transition. Evidence that (C + a) slip is associated with increased ductility in a high-pressure environment has been found in stress-strain tests on poly crystalline beryllium.10 The present paper describes a study on the influence of a hydrostatic pressure environment on the occurrence of (c + a) slip in beryllium single crystals. Material of two purity levels was tested in c axis compression over the pressure range ambient to about 27.5 kbars.* 1) MATERIAL PREPARATION AND CHARACTERIZATION Two lots of low-purity single-crystal beryllium were used. The first lot was "ingot secondary refined grade" and designated lot A. The second lot (lot B) was produced by a two floating zone pass zone-leveling operation in an argon-filled sealed quartz apparatus on a 1-in.-diam by 12-in.-long bar of Pechiney secondary refined-grade vacuum-cast and hot-extruded material. The high-purity material (lot C) was made by traversing twelve floating zone passes through a similar bar of Pechiney secondary refined-grade vacuum-cast and hot-extruded material. In a series of spark cutting and lapping procedures,11 single-. crystal specimens some 0.12 in. sq by 0.30 in. high were made with the sides Parallel to the first- and second-order prism planes and the basal plane within 3' of arc of the top and bottom surfaces of the specimen. Such an accurate orientation is necessary because of the large difference in resolved shear stress

Jan 1, 1970

By James S. Foster, Paul G. Shewmon, Frank V. Nolfi

Analytical expressions are developed for the kinetics of dissolution or growth of a spheroidized, solute rich stoichiometric Precipitate in the surrounding matrix. There are two limiting cases; in one the rate of dissolution or growth is limited by long range solute diffusion through the matrix and in the other by the transfer of atoms across the mrdrix-precipitate interface. In the former case local interfacial equilibrium exists while in the latter it does not and the rate of dissolution or growth is controlled by an interfacial reaction. The analysis treats both limiting cases as well as mixed control in a single development, where it is found that the thermodynamic state of the interface is completely specified by a single parameter, o, defined by where K is the reaction rate constant, D is the matrix solute diffusivity, and R, is the precipitate radiz~s. If K is infinite then a is zero and local equilibrium prevails; if K deviates infinitesimally from zero, then a is very near unity and an interfacial reaction is rate controlling. Mixed control occurs for intermediate values of o. From the analytical results, numbers are computed which are useful in determining the duration of interfacial reaction or mixed control; following this time period, long range diffusion is rate controlling. THE rate controlling process or processes governing phase boundary migration has been the subject of much speculation and investigation. Traditionally, the most widely assumed boundary condition in quantitative treatments of this problem has been that of local interfacial equilibrium. This condition implies that long range diffusion of one or more elements controls the migration and is referred to as "diffusion controlled migration" (herein DCM). In contrast to the above view is the proposition that local interfacial equilibrium does not exist and that transport of atoms across the interface is rate controlling. Consequently, this mechanism is referred to as "interface controlled migration" (herein ICM). In processes of the latter type, the activity, a, of one or more elements is discontinuous at the phase bound- ary and the flux, J, across the boundary of a given element is some function of its activity discontinuity, a. One of the most comprehensive contributions to a mathematical description of phase boundary migration is due to am.' His analyses are applicable to precipitation in binary systems in which a) the precipitates are spherical* solute rich compounds of constant

Jan 1, 1970

By F. A. Crossley

The additions: o, Sn, Zr, Cb, Mo, and V were studied for their effects on the a/a + Ti3A1 boundary of Ti-A1 base ternary alloys. These additions were chosen because of their importance to commercial titanium alloy practice—oxygen as the major impurity (in terms of influence on mechanical properties) and the others as major alloying additions. The composition and temperature ranges of investigation varied according to the system as shown in Table I. The principal means of investigation was light-microscopy. The basis of the ternary studies was the recently determined titanium-rich end of the Ti-A1 system.' MATERIALS, METHODS, AND PROCEDURES Ingots were prepared in 15 g size for all alloys except those of the Ti-Al-Mo and Ti-A1-V systems which were prepared in 20 g size. These alloys were prepared from high-purity, electrolytically refined titanium obtained from the Bureau of Mines, Boulder City Metallurgical Laboratory, Boulder City, Col., and Chicago Development Corp., Riverdale, Md., for the 15 g and 20 g ingots, respectively. The alloying additions were obtained from commercial sources, and were at least of 99.9 pct purity, except the V-15 wt pct A1 master alloy for vanadium additions. This alloy was of 98.2 pct purity; the major impurities were 0.37 wt pct Fe and 0.38 wt pct Si. The ingots were prepared by multiple melting in a nonconsum-able-electrode arc furnace. The ingots were covered with Markal coating "CR-T22" (Markal Co., Chicago) to protect them from scaling. Markal coating is applied as a slurry of solids in a volatile carrier liquid. The coated article is air dried. Upon heating to the hot working temperature the coating fuses to form a glassy, protective film. The ingots were heated to 1000°C and rolled to 0.16 in. thickness, reheating after each pass. The glassy film was removed by sand blasting. Ten mils were removed from all surfaces by grinding and/or pickling (3 pct HF, 30 pct HN03, balance water). Grinding was always followed by pickling to remove traces of the grindmg medium. Hydrogen removal was accomplished by vacuum annealing at 1000°C for 2 hr to a final pressure of about 0.02 µ Hg. This was followed by annealing in evacuated Vycor bulbs (800°C, 2 hr, ice brine quenched (IBQ)) in order to maximize ductility. The materials were then lightly pickled and cold rolled to 0.12 in. thickness or cracking, whichever occurred first. After rolling, 1/2 by 1/4 in. specimens were cut for the equilibration anneals given in Table 11 and carried out as previously described.1 Final polishing of the specimens for metallographic examination was done by electrolytic means. Specimens were first examined without etching under bright field and polarized light illumination, for this is the only means of detecting the "two-phase" phenomenon.1,2 The term "two-phase syndrome" refers to Ti-A1 al-loys which appear on the bases of their chemical, phys-ical, and mechanical properties, to be two-phase, but are actually single phase and inhomogeneous in composition. Since processing and heat treatment of the alloys of the first group were completed before the two-phase syndrome was discovered, a number of the specimens were found to exhibit this phenomenon—80 pct of those of the Ti-Al-Zr system, 5 pct of those of the Ti-Al-Sn system, 30 pct of those of the Ti-Al-Zr system. The affected specimens were homogenized by heating above the ß transus temperature and quenching. The heat treatment and working schedules to accomplish this are given in Table 111. After rolling, specimens were pickled (3 pctHF, 30 pct HNO3 in water) to remove 1 to 2 mils from the

Jan 1, 1970

Jan 1, 1970

By B. Haimson, C. Fairhurst

One of the main functions of rock mechanics research has been to find ways of determining in-situ stresses. Many methods have been suggested, the most significant ones calling for measurements inside bore- holes. These methods usually employ some instrumentation for the purpose of measuring hole deformation. Several years ago, a new method was suggested by Scheidegger,l based on previous work by Hubbert and Willis.2 It was the method of "hydraulic fracturing," which had been introduced by the oil industry in 1948 for the purpose of oil-well production stimulation. Basically, hydraulic fracturing consists of sealing off a section of a borehole, pumping in a fluid, and pressurizing it until fracture occurs. If pumping is continued vigorously, the fracture is opened up and extended. In an oil field, such an artificial fracture increases the overall permeability of the formation and usually enhances production. During the entire operation, the variation of pressure with time is ordinarily recorded. Hubbert,2 Scheidegger,1 Kehle,3 and others have shown that the recorded pressures can be theoretically related to the magnitudes of the principal in-situ stresses; the orientation of the fracture can often be used to determine the direction of the principal stresses. The advantage of hydraulic fracturing over the present in-situ stress determination methods is simplicity: no sophisticated instrumentation is required inside the borehole; hence, the stresses can be measured at any depth. Moreover, if the formation is impermeable to the fracturing fluid, no elastic constants of the rock are required in calculating the stresses, a

Jan 1, 1970

By E. D. Fields, R. W. Sayers, M. C. Tippett

The Duval Corp. porphyry copper deposits at Copper Canyon and Copper Basin, though widely separated, form an econornic unit requiring integrated exploitation. Contrasts in mineralization, host rocks, and mode of occurrence present unique mining and milling problems. Mixed oxide-sulfide ore is treated in extensive dump leaching facilities in both areas. Complex Cu-Au-Ag ore is treated in a 4000-tpd mill at Copper Canyon. In both areas, hypogene metallization occurs within large aureoles of metamoiphism and hydrothennal alteration related to quartz monzonite intrusions of mid-Tertiary age. Supergene processes fitrther altered the rocks and enriched the hypogene protore. At Copper Canyon, hypogene copper and iron sulfides with gold and silver occur in fractures, as partial replacement of favorable beds, and as disseminations in Paleozoic sedimentary rocks. The lower part of the Pennsylvanian Battle formation was a particularly favorable host. Metallization occurs to a lesser extent in quartz monzonite. Metal zoning is well-developed. The deposits at Copper Basin consist principally of supergene copper minerals in arenites of the Cambrian Harmony formation. Oxidation of hypogene copper and iron sulfides in tactite zones has formed at least two commercial deposits; intersections of fractures with favorable beds exerted important ore controls. Recently, the Copper Canyon and Copper Basin properties of Duval Corp. have been added to the list of porphyry copper mines in Nevada, marking the first new copper open pit in this state in 15 years. The properties are situated in the Battle Mountain

Jan 1, 1970

By D. V. Edmonds, C. J. Beevers

Tensile tests were carried out on a! titanium containing 850, 1250, and 2700 ppm 0, and up to -500 ppm H. The tests were performed at -196", -78", 20°, 150°, and 300°C at a strain rate of -1.0 x 10??3 sec-1. Increasing oxygen content, increasing grain size, and decreasing test temperature resulted in enhanced embrittlement of the a titanium by the hydrogen additions. Metallographic observations showed that this can be correlated with the influence of these parameters on the introduction of cracks into the a! titanium by fracture of titanium hydride precipitates. CRAIGHEAD et al.1 reported that the hydrogen content normally found in commercial-purity a! titanium (60 to 100 ppm) was sufficient to cause a substantial lowering of the impact strength, and they attributed this embrittling effect of hydrogen to the precipitation of titanium hydride. Lenning et al.&apos; found that in commercial-purity a titanium there is an almost complete loss of impact strength at about 200 pprn H, which is approximately half the value needed to eliminate the impact strength of high-purity a titanium. They also showed that the presence of 3000 ppm hydrogen reduces the room-temperature tensile ductility of commercial-purity material to a value of the order of 10 pct; the corresponding hydrogen concentration for high-purity titanium is over 9000 ppm. It thus appears that the detrimental effect of hydrogen on the mechanical properties of commercial-purity titanium becomes evident at much lower hydrogen contents than for high-purity titanium. The main difference between the two types of a titanium might be expected to be the higher level of interstitial impurity in the commercial-purity grade. Jaffee et a1.3 studied the influence of temperature and strain rate on the hydrogen embrittlement of high-purity and commercial-purity ! titanium. In general, the behavior was the same for both materials; embrittlement was enhanced by decreasing temperature and increasing strain rate. Recent results from tests on commercial-purity a titanium containing 850 ppm O and varying amounts of hydrogen up to -500 ppm showed that the degree of embrittlement by hydrogen is intimately related to the fracture characteristics of titanium hydride precipitates.4 The present paper considers the interrelationship between the mechanical properties and micro-structural features of commercial-purity a! titanium containing 850, 1250, and 2700 ppm 0 and varying amounts of hydrogen up to -500 ppm. 1. EXPERIMENTAL PROCEDURE Three types of commercial-purity titanium supplied by IMI* were used in the investigation, and for the *Address: Witton, Birmingham 6, United Kingdom. purpose of this paper are designated Ti 115, Ti 130, and Ti 160. The principal impurity elements are given in Table I. The material was received in the form of 12.7 mm diam bars having a fully recrystallized structure. Tensile specimens with a round cross-section of 4.5 mm diam and a gage length of 15.2 mm were machined from the bars. In order to develop the same grain size (mean linear intercept of grain boundaries) in each of the three types the specimens were annealed under a dynamic vacuum of <10?5 mm Hg, Table 11. Specimen hydriding was carried out in a modified Sieverts apparatus;&apos; hydrogen was taken into solution at 450°C and after holding the specimens at this temperature for 24 hr they were furnace-cooled to room temperature at an average rate of -100 C deg per hr. By this method nominal hydrogen contents of 0, 50, 100, 250, and 500 ppm were introduced into specimens of Ti 115, Ti 130, and Ti 160 (100 ppm (wt) -0.5 at. pct). The actual hydrogen contents were calculated from the weight differences obtained by weighing the specimens before and after the hydriding treatment. Tensile tests were carried out at temperatures of -196", -78", 20°, 150°, and 300°C on a 10,000 kg In-stron machine at a nominal strain rate of -1.0 x 10-3 sec-1. Fractured specimens were sectioned in planes parallel to the tensile axis, mechanically polished to 0.25 µm grade of diamond paste, and then attack polished using a solution containing by volume 99 parts H2O, 1 part HF, and 1 part HNO3. Although the latter treatment unavoidably opened out cracks and voids visible after mechanical polishing, it did reveal the grain structure, titanium hydride morphology, and deformation twinning structure.

Jan 1, 1970

By W. G. Oldham

By monitoring the capacitance of abrupt p-n junctions it is possible to follow the motion of substitu-tional impurities. A p-n junction is formed by growth of silicon from an Al-Si alloy on an n-type silicon sutstrate at a temperature in the range 650" to 750°C. The diodes are etched and sorted for consistent V-I and capacitance behavior and separated into groups. After irradiation, each set with an unirradiated control set is annealed to various temperatltres for 10 mm and the capacitance remeasnred. For very heavily doped diodes (-1019 per cm3) observable capacitance changes occur at neutron fluences of >1015 per cm 3. The results may be interpreted in seceral ways, the simplest of which is to assume simple vacancy diffiision with small impurity -racancy interaction (at the diffiision, i.e. annealing temperature of 700°C). In this interpretation it is found that a typical vacancy makes about 1024 jumps and travels about 10-5 cm before disappearing. The required effective annihilation center density is about 1016per cm3 . Estimates of the vacancy-impurity interaction can be made and the above numbers correctecl, but for arty reasonable assumptions the number of vacancy sinks connot be much reduced. ThE complete annealing of radiation induced defects requires that the vacancies and interstitials either recombine, travel to the surface of the crystal, or travel to an annihilation center, e.g., a dislocation or a precipitate. If the interstitial is ignored except as a possible vacancy annihilation center at low temperatures,* the motion of vacancies may be followed by monitoring the corresponding motion of substitutional impurities. pfister2 has measured the enhanced diffusion of impurities in an asymmetric shallow diffused silicon structure by optically monitoring the junction movement. In these experiments we monitor instead the capacitance of a heavily-doped deep symmetric p-n junction. The sensitivity for this method is several orders of magnitude higher than in Pfister&apos;s technique, mainly for two reasons: 1) the junction capacitance of a heavily-doped junction is sensitive to impurity movements in the Angstrom range* com- and 2) the junction may be far from the surface which is a major annihilation center for vacancies. THE EXPERIMENT A p-n junction is formed by the epitaxial growth of silicon from an A1-Si alloy on a silicon substrate at a temperature in the range 650° to 750°C. The technique used is the transport of an aluminum melt through a temperature gradient.4 A 10-mil thick aluminum disc is sandwiched between two silicon wafers and the assembly raised to about 650° C with a temperature gradient normal to the sandwich. After about 8 hr the upper (hotter) wafer has been entirely transported and deposited epitaxially on the substrate wafer. The substrate and overgrowth resistivity are measured with a 4-point probe. The as-grown structure is lapped until the wafer is about 1/2 mm thick with the junction in the center. Contacts consisting of electroless nickel covered by electroplated rhodium are applied to both the p and n sides. The wafer is diced into square dice 1/2 to 1 mm on a side and the dice are etched sufficiently to remove approximately 1 mil of silicon. The following results are all for aluminum (p-side) and antimony (n-side) doped specimens with NA =3x 1018 per cm3, ND = 2-8 x 101A per cm3. The diodes are sorted for consistent V-I and capacitance behavior and separated into groups. After irradiation, each set with an unirradiated control set is annealed and the capacitance remeasured. A special capacitance measurement method is used to insure a low sensitivity to shunt resistance. The diode is voltage driven and the current monitored by a phase lock amplifier. It is possible to adjust the detector phase to a point where shunt resistances as low as 100 O have no effect on the reading. The diodes in this study have a capacitance in the range 1000 to 5000 picofarads and a shunt resistance in the range 100 to l06 O depending on the stage of the anneal. THEORY The theoretical problem is twofold: 1) The computation of the amount of impurity diffusion and hence the impurity profile resulting from a given amount of vacancy motion, and 2) the computation of the capacitance from the impurity profile. A comparison of the theoretical and experimental capacitance (in particular the changes) yields the amount of vacancy motion. Vacancy Motion. A convenient parameter to measure the total amount of vacancy motion is Jv the total number of vacancy jumps per unit volume. Although this parameter varies with position in the crystal, owing to vacancy annihilation at the surfaces, it is approximately independent of position far from the surfaces, i.e. in the junction region. In terms of the number of vacancies per unit volume Nv and the vacancy diffusivity given by

Jan 1, 1970

W ho holds title to the continental shelf? As submarine mineral ventures move out into deeper and deeper waters, the dispute over this question is bubbling up with greater and greater urgency. Basically, the forces of disagreement are lined up on two fronts--one nationalist and the other internationalist. The nationalists, or "broad shelf" proponents, view the shelf as a geologic extension of the coastal nations and therefore subject to the sovereignty of these nations. The internationalists or "narrow shelf" proponents, seek to circumscribe the jurisdiction of the coastal nations by a topographic line beyond which all rights would be reserved to an international regime. In the U.S. public sector, three groups----the American Bar Association and International Law Association committees and the National Petroleum Council (NPC) - have taken a stand on the broad shelf. These are joined by AIME, which has consolidated its position in a "Policy Statement on the Outer Limit of National Sovereignty Over Seabed Resources." This statement was adopted by the AIME Board of Directors last October 15 after its submission by Earl Cook, Chairman of the AIME National Affairs Committee, at the behest of the Society of Petroleum Engineers. The main organization holding to the narrow shelf is the Commission on Marine Science, Engineering and Resources.

Jan 1, 1970

By G. L. F. Powell, L. M. Hogan

Samples of silver and Ag-O alloy, 0.12 wl pet, have been undercooled to a maximum of 250°C by melting in a slag of commercial soda-lime glass. Grain refinement occurred in undercooled silver samples whet the degree of undercooling exceeded a critical value which varied from 153° to 175°C, depending on the melting conditions. In under cooled Ag-0 samples, the grain structure was fine and equiaxed at degrees of undercooling larger than 50oC. The grain refinement in both silver and Ag-0 alloy samples was the result of recrystallization during or immediately following freezing. When the oxygen content was increased, the degree of undercooling at which recrys-tallization occurred decreased. INVESTIGATIONS of the grain structure of strongly undercooled melts of nickel and cobalt1-4 have revealed a change in room-temperature grain size as a function of undercooling. At large degrees of undercooling the grain size was fine, but samples undercooled by smaller amounts exhibited a much coarser grain structure. The reported undercooling at which this grain size transition occurred in nickel varied between 140° and 175&apos;C undercooling. Walker1 attributed this grain size change to an enhanced nuclea-tion rate. Cavitation at a melt-solid interface was con sidered to generate a high-pressure wave. This, in turn, produced nucleation in the liquid as a result of an elevated freezing point increasing the undercooling in the melt. A similar grain size transition was observed in undercooled silver between 133° and 153°C undercooling.5 The grain size transition in undercooled silver was found to be dependent on oxygen con tent. More recently, the authors5 showed that a simila transition occurred in an undercooled Cu-O alloy, =0.08 pet, but not in oxygen-free copper undercooled more than 200°C. The transition was attributed to recrystallization of the solidified grains after freezing; the greater the degree of undercooling, the more complete the recrystallization. In view of this effect of oxygen content on grain size transition, additional undercooling experiments were carried out with silver. This paper reports the results of these studies on silver and Ag-O alloys undercooled more than 50°C EXPERIMENTAL 1) Materials. The silver was supplied by Matthey Garrett Pty., Ltd., as fine granulate, silver mini&apos; mum 99.9 pet, and contained the trace impurities shown in Table I. The silver originated from two different refineries resulting in the difference in impurity content shown in Table I. However, the variation in composition had no discernible effect on the undercooling behavior. Samples of the silver were melted in an open-ended, vertical, cylindrical resistance furnace, wound with Kantha] wire, the temperature of which was adjusted by means of a variable transformer, 2) Melting and Undercooling. Bulk samples of silver were undercooled by preoxidation and removal of oxidized impurities in a glass slag, as previously described,5 but special precautions were necessary to allow comparison between oxygen-free silver and a Ag-O alloy. Samples free of oxygen were prepared by first melting weights of granulate varying from 200 to 400 g in clean vitreous silica crucibles in air for approximately 15 min. A sample was frozen and a complete glass cover formed over the top surface by adding granulated glass rod. The sample was then melted and frozen several times until no oxygen bubbles appeared in the glass slag. Subsequent thermal analysis indicated that the oxygen content was negligible. The glass acted as an efficient barrier to absorption of oxygen from the air. Ag-O alloys were prepared by melting silver in silica crucibles with only a partial cover of glass, so that the top surface of the melt was in contact with air. The silver was held molten in air for several hours at 1000° to 1050°C, in the expectation that the oxygen in solution would reach equilibrium with atmospheric oxygen. At T - 1000°C the equilibrium oxygen content was calculated as 0.12 wt pet O, using Sieverts law and Eq, [l], derived by Mizikar et a!.7 from the data of Sieverts and Hagenacker8 for 1 atm of oxygen:

Jan 1, 1970

By Richard A. Walker, John P. Hager

The thermodynamic properties of the Pb-Au system have been determined between 750" and 1075°C by means of the cell Mo, Pb(1) |(PbO-SiO2){l) , SiO2(s) |Pb-Au(1), Mo The activities of lead and gold exhibit negative deviations from ideal behavior; the values of ? pb and ? the raoultain activity coefficients at infinite dilution, being 0.24 and 0.25, respectively, at 1200°K. The liquidus curve for the gold-rich region of the Pb-Au phase diagram has been determined from measure-ments on seven alloy compositions in the two phase region (liquid + Au(s)). The standard free energies of formation of Au2O(l) and Ag2O (1) have been estimated from cell measurements obtained by replacing the alloy electrode with pure liquid gold and silver. A new integral molar heat of mixing curve for the liquid Pb-Au system is presented and the results of previous studies discussed. The contribution of HM to FE was found to be small relative to TSE. THE use of galvanic cells of the type A(l) |A+Za|A - B(l) [I] provides an accurate means for the thermodynamic study of liquid alloy systems. In Part 1&apos; it was shown that cells of type [I] may be extended to higher temperatures and to a wider range of alloy systems if the ion A+Za is incorporated in an appropriate molten oxide phase, rather than in the classical fused salt electrolyte. In the following investigation the experimental method is extended to an investigation of the thermo-dynamic properties of the Pb-Au system by use of the cell: Mo, Pb(l) | (PbO-SiO2)(l), SiO2(S) |Pb-Au(l), Mo [] Previous measurements on liquid Pb-Au alloys were obtained by Kleppa2 by electromotive force measurements on a galvanic cell involving a molten chloride electrolyte. These measurements were confined to temperatures less than 830°C and compositions with X Pb > 0.2 because of the instability of the cell at higher temperatures. Later measurements by Kleppa3 on the heats of formation in the composition range 0.67 < Xpb < 0.98 were not consistent with the results by electromotive force measurement. The purpose of the present study is to extend the temperature and composition range of the thermodynamic properties and to obtain an independent measure of the integral molar heat of mixing over the entire composition range.

Jan 1, 1970

By K. R. Evans

The yield and fracture characteristics of a Ti-8 pct A1 alloy have been examined at room temperature as a function of exposure temperatures to 1700°F. Em-brittlenzent of the alloy is observed to occur following exposures below 1280°F, the critical temperature for formation of ordered Ti3Al particles. Presence of Ti3Al particles results in an increase in the yield and flout stresses which, for a given exposure time, are a maximum at the critical temperature. Embrittlement is attributed to the occurrence of plastically induced fracture controlled by the increase inflow stress. This interpretation is compatible with the decreasing ductility and increasing crack popagation rates observed with increasing exposure time below the critical temperature. Slip line observations and measurements of the gain size dependence of the yield stress indicate that the slip character of the alloy is not influenced by exposure treatments below the critical temperature. ThE potential usefulness of Ti-A1 alloys in structural applications has prompted considerable interest in studies of their microstructure and mechanical characteristics. The relatively recent surge of interest in the system and at the same time its complexities are indicated by the fact that despite numerous recent efforts14 there has not even been general agreement upon a phase diagram for the system. However, most of the Ti-A1 alloys of commercial interest range in aluminum content from 5.0 to 8.5 wt pct where most investigators achowledge the existence of the ordered Ti41 phase. Goldak and parrs confirmed the existence of Ti41 from X-ray diffraction analysis of the stoichiometric composition while Blackburn6 has determined its presence in commercial Ti-8 pct A1 alloys by electron diffraction analysis and dark field transmission microscopy. The embrittlement of Ti-8 pct A1 alloys was initially reported by Crossley and carew7 who showed that aging in the temperature range of 750" to 1110°F resulted in extreme brittleness. This behavior was later confirmed and correlated by Soltiss to the presence of long-range order in the commercial Ti-8 pct Al-1 pct Mo-1 pct V alloy (Ti-8-1-1) which exhibited anomalous creep and yield strength behavior at 950°F. This investigation was designed to study the mechanical characteristics of a binary Ti-8 pct A1 alloy in order to further examine the nature of the embrittlement behavior reported for the alloy system. EXPERIMENTAL PROCEDURE A Ti-8 pct A1 binary alloy was obtained from the Wah Chang Co. in the form of 0.050 in. sheet. The chemical composition of the alloy is given in Table I. Heat-treatment of the alloy was conducted in evacuated vycor capsules for the tensile sDecimens (1.25 bv 0.25 in. gage section) and in evacuated stainless steel jackets for the crack growth-rate panels. All specimens were annealed at 1700°F for 24 hr and water quenched before an exposure at elevated temperatures. Tensile testing was conducted at room temperature in an Instron testing machine equipped with a pushbutton control for instantaneous control of the cross-head motion. In this manner the change in stress, Aa, accompanying an increase in strain-rate by a factor of 10 was measured immediately after yielding. The crack growth-rate panels used were 3 by 18 in. with a precrack 0.33 in. long cut into the center of the panel. The panels were cycled at a maximum gross stress of 40,000 psi at a maximum to minimum tension stress ratio of 20. Cycling of the specimens was continued until the crack propagated the width of the panels. The crack length was intermittently measured during slow crack growth. EXPERIMENTAL RESULTS Correlation of Embrittlement to the Critical Temperature for Ordering. Blackburn6 has found that the critical temperature, T,, for the formation of Ti41 in a Ti-8 pct A1 alloy with an interstitial content on the order of that given in Table I is approximately 1245°F. The relationship between the ductility of the binary alloy used in this investigation and T, was estimated from tensile tests on specimens which were exposed for 24 hr at various temperatures followed

Jan 1, 1970

By Morris Cohen, Robert C. Ruhl

Fe-Ni-B alloys were inresligated by X-ray diffraclion after splat quenching. Although this rapid cooling did not produce a measurable supersaturation of dissol1ed boron in either binary Fe-B or Ni-B alloys, a marked increase in dissolved boron was achieved by the splal quenching of lernary Fe-Ni-B alloys. Boron additions up to 2.0 wl pcl to Fe-13Ni and Fe-24Ni alloys cause an increase in retained austenite from 0 to 59 pet and to 92 pet, respectively. The martensitic phase in the Fe-13Ni-9 at. pct B alloy is .found to conlain about 0.6 at. pet interstitial boron, as evidenced by the tetragonality of this phase, and about 3.6 at. pct substilutional boron, us deduced from the lattice paratrieler decrease, the balance of the boron being precipitated as (Fe,Ni)aR. The austenitic Fe-Ni-B plznses also contain both interstitial and substitutional boron. Iron-Boron System. The phase diagram and related information about the solid solutions and intermediate phases in the Fe-B system are given by ansen,&apos; Elliott.2 and Pearson.1 The equilibrium solid solubility of boron in both ferrite and austenite is quite small: the maximum solid solubility of 0.02 wt pct B (0.11 at. pct B) occurs in iron at the eutectic temperature of 1150°C. while the maximum solubility in a iron is less than 0.01 wt pct.l There is disagreement in the literature as to whether these solid solutions are substitutional or interstitial. Based on the measured activation energy of boron diffusion in iron, it appears likely that boron moves interstitially in austenite. 4 However, this observation does not rule out the possibility that some of the dissolved boron may also occupy substitutional sites in this phase. Investigations of internal friction of boron in iron have suggested that boron is interstitial there.&apos; Shevelev, 5 on the other hand, reports a decrease in the ferrite lattice parameter with dissolved boron content, thus indicating a substitutional solution. Unfortunately. Shevelev&apos;s methods and analysis are unclear. Goldhoff and spretnak6 have measured the lattice parameters of pure iron and an Fe-0.005 wt pct B (0.027 at. pct) alloy at both room temperature (ferrite) and from 920° to 1200°C (austenite). They reporte: a lattice contraction in the ferrite of 0.0003 ± 0.0002 due to boron, thus indicating a predominately substitutional solution. Appreciable (0.0010 to 0.0060) lattice contractions were found in boron-containing austenites, but these effects were much larger than could be accounted for by the substitutional solution of all the boron present. Nickel-Boron System. Elliott 2 gives a summary of thephase diagram and recent work on this system. The solubility of boron in nickel reaches a maximum of 0.03 wt pct at the eutectic temperature of 1080°C. Iron-Nickel System. ansen&apos; presents the equilibrium diagram for this system and also discusses the metastable austenitic and martensitic phases along with the a=? transformations. The lattice parameters of Fe-Ni ferrites have been recently redetermined by Abrahamson and Lopata.7 Their data, Fig. 1, show an unusual change in slope at about 1.7 at. pct Ni. Very few measurements of the lattice parameters of Fe-Ni martensites are available in the literature. The values of Roberts and Owen8 are considerably higher than those measured in the course of the present work: they find that a, is constant at 2.874? from 8 to 30 at. pct Ni. Both the slope change in the ferrite parameters and the occurrence of a maximum plateau in the marten-sitic lattice parameters vs composition denote the

Jan 1, 1970