Search Documents

By S. J. Rothman, A. L. Harkness, L. T. Lloyd

Self-diffusion in Y uranium has been measured using U235 as the tracer isotope. The diffusion coefficient fits an Arrhenius-type equation D = 2.33 x 10 -3 exp (- 28,5000/RT) cm2/sec The values of Do and Q are unusually low and are not consistent with the values expected from theories based on a simple vacancy mechanism of diffusion. CYLINDRICAL samples, 1 cm in diam and 1/2 to 1 cm long, were prepared from high-purity uranium containing 0.0343 pct u235, Table I. The samples were water quenched from 690°C (the a-ß transformation is at 668°C) to remove preferred orientation, and annealed at 450 "C to minimize residual stresses. One end of each cylinder was polished on a 1-µ diamond lap and electropolished in a phosphoric acid solution. After a final cleaning by cathodic sputtering, a 1- to 3-µ thick layer of the tracer isotope, uranium containing 93 pct u235, was sputtered onto the sample.' To prevent contamination during the diffusion anneal, the diffusion couples were placed in a tantalum cup and covered with another piece of uranium, and the whole assembly was sealed off in an evacuated quartz tube. Annealing temperatures were constant within +2.0°C. The samples were heated and cooled slowly between room temperature and the ß-? transformation (774°C) in order to minimize distortion of the sample surface that might arise from aniso-tropic thermal expansion and density changes during phase transformations. After machining off 1/16 in. from the radius to

Jan 1, 1961

By R. J. Charles, G. Agar

Experiments on single particles show that the amount of material created during impact that is finer than any chosen size is proportional to the energy of the impact. As the underlying principle of comminution, it might be stated that each unit of energy input to a given comminution system tends to add to the system an identical assembly of new particles and subtract an equivalent volume of larger particles. Thus, two of the consequences of the fact that each unit of energy tends to add identical assemblies of new particles to the system are: 1) on continued application of energy the total charge in any batch comminution system tends to assume the characteristics of this assembly, and 2) the process of comminution may be described by a relationship such as E = Ak-a. Recently Schuhmannl presented a theory of comminution which puts rational perspective on the extensive controversy surrounding most of the existent theories of comminution. With hindsight the origin of controversy can be ascribed to a relatively simple circumstance. In general, a progressive shift of a size distribution curve towards finer sizes is observed as energy is added to a comminution system. It is also observed that, with continued grinding, the size distribution curves usually change and appear to approach some constant shape. Inves-tigators generally felt that an appropriate method of relating and generalizing such data would be to consider the hypothetical case where particles in the system were uniformly subjected to comminution such that each of these particles, receiving its proportion of input energy, was transformed into a number of smaller particles of uniform size. Since the changes in shape of the size distribution curves during size reduction were clearly associated with the coarse particles in the system, it was also assumed that these changes accounted for little of the input energy and one could deal solely with the equilibrium shape towards which the size distribution curves tended. Although the unrealistic nature of the foregoing points of view was realized some justification was felt for such treatments since, in most cases, the resulting mathematical formulae could, by the adjustment of at most two parameters, satisfactorily describe experimental observation. Difficulties arose, however, in that the formulae required a specific influence of the feed size on the comminution process. In actual fact, the application of a feed size term in fitting experimental data was often found to be unnecessary or contrary to the above formulae. Secondarily, much discussion arose concerning the appropriate energy number that would relate the size change of one particle to the amount of comminution energy it received. As has been previously shown3 all the above theories that treat comminution as a continuous process of size reduction may be related to a proposition of the following form: dE = -Cfn [1] where dE is the increment of energy, dx is the size change, x is the particle size, and C and n are constants. It is now clear, as pointed out by Schuhmann, that Eq. 1 is inapplicable to comminution processes, since comminution cannot be considered other than as a discontinuous mixing process in which the overall size distribution of the product results from mixing, in various proportions, finished material with unfinished, and sometimes untouched, material. A striking illustration of this mixing phenomena may be obtained by comparing the size distributions of grinds in a typical batch ball mill with size distributions calculated on the basis of mixing various proportions of feed material with a ground material which obeys a power law size distribution relationship. Figs. la and lb illustrate such a comparison and the similarity of these figures indicates that mixing plays an important role in determining the overall shape of the product size distributions. Figs. la and lb illustrate, additionally, the underlying basis of the comminution theory presented by Schuhmann.' In the preliminary grinding of relatively close sized feed particles in a batch ball mill, one may visualize that, when a successful encounter of a ball with a feed particle occurs, then the particle undergoes severe size reduction and the size range in which the resultant particles reside is far removed from the size of the feed particles. After a number of feed particles are reduced by independent but similar impacts and one examines the size dis-

Jan 1, 1961

By D. N. Collins, J. R. Stevens

New expressions in the technical assessment of mineral concentration processes have been defined as Concentration Efficiency: Concentration Index: where h is the percentage of head grade; c, percentage of concentrate grade; maximum percentage of concentrate grade obtainable at 100 pct recovery; and R, percentage of recovery. In developing these expressions, the basic requirements for the technical assessment of concentration operations have been defined and the various expressions suggested by others for asses-sing the results of such operations reviewed and criticized. The derived expression for E, depends on a simple combination of recovery (R) and a new term selectivity (s), where S is (c-h)/(c,,, -h), by definition. Limitations of the new expressions are discussed and examples given of applications to concentration operations. It is also shown that the formulae for E, and I, can be applied to scatter diagrams, multi-component systems, size-assay analyses, and classification data. Many methods of quantifying concentrating operations have been proposed. These include direct presentation of weights and assays together with the derived data for other items such as ratio of concentration, recovery, rejection losses, and enrichment ratio. These terms are now accepted mineral dressing nomenclature, and in the assessment of the results of concentration processes, concentrate grade and recovery are together the most widely accepted measures of concentration efficiency. For practical purposes when the concentrate grade is equal to or greater than a predetermined acceptable value, test or operation results may be assessed by the recovery figures alone. Similarly when recovery is within specification, the operation can be assessed by concentrate grade. The ultimate assessment and selection of a concentration operation is—admittedly with a few ex-ceptions—a matter of economics. There is however an intermediate stage in laboratory and pilot plant testing when evaluations must be made without the assistance of an economic yardstick. Numerous techniques are employed to facilitate such evaluations among which may be mentioned graphical plots of grade vs recovery, cumulative weight vs cumulative recovery, scatter diagrams, etc. The desirability of combining metallurgical results and product weights and assays into a single value has been recognized and discussed by many workers1-" with the resultant suggestion and use of such terms as Metallurgical Efficiency ,' Summation Index,' Selectivity Index,'- and Absolute Efficiency B None of these expressions completely satisfies all the requirements of a selectivity or efficiency formula and it is proposed in this report to define the terms, relating to the technical efficiency of a concentrating operation, concentration index and concentration efficiency. Examples are given of their application and a comparison is made of their use in relation to other formulae. All product grades in this paper will be referred to in terms of mineral percentages and a list of symbols is given in Table I. CONSIDERATION OF EXISTING FORMULAE A number of the existing efficiency and index terms used in quantifying concentrating operations are considered below. Metallurgical Efficiency:

Jan 1, 1961

By L. E. Lynd

Ilmenite concentrates prepared from beach and dune sands of Florida, India, Australia, and other localities deviate to varying degrees from the theoretical composition of pure ilmenite, and generally contain more TiO2 than the formula FeTi03 would indicate, and some Fe2O3. This variation in composition is due to different amounts of altered ilmenite in the concentrates. (') The alteration has been shown to take place by oxidation and leaching of the iron in ilmenite, to yield residual products consisting of amaphous or very finely crystalline titanium dioxide and ferric oxide. Other studies(2) have stressed that ilmenite may alter first to an amorphous titanium-iron oxide, or to an amorphous mixture of titanium and iron oxides, with later alteration to crystalline titanium dioxide. There has been some speculation as to whether alteration of ilmenite is usually caused by weathering or by hydrothermal pr0cesses.(3,4,5 Three main methods of approach were used to study the mechanism and rate of ilmenite weathering. (1) Etch tests were used to learn the relationship between crystallographic orientation and the rate of chemical attack on ilmenite. (2) Altered ilmenites in New Jersey sands were compared with ilmenite in rocks of the area from which the sands were probably derived. (3) Experiments were carried out to determine at what rate, and by what agents, originally fresh ilmenite could be altered in the laboratory under simulated weathering conditions. ETCH FIGURES ON ILMENITE CRYSTAL PLANES A rather large ilmenite crystal from Sannidal, Norway, about 11/2 x 11/2 x 2 inches, bearing a few natural faces with imperfect surfaces, was prepared for etching by grinding and polishing crystal planes whose Bravais-Miller indices (referred to hexagonal axes) had been determined by X-ray methods to be 00.1, 10.0, and 10.2. Metallographic examination showed that the crystal was homogeneous, and uniform in orientation, except for the presence of twin lamellae which were oriented with their broadest surfaces parallel to the 00.1 planes of the large crystal. Since ilmenite is rather inert to standard etch reagents, strong solutions of hot sulfuric acid and cold hydrofluoric acid were used. Preliminary tests established that better etch figures were obtained using HF than with H2So4 solutions. The etch figures produced on 00.1 and 01.0 planes of ilmenite by etching 3 to 5 minutes in cold concentrated HF solution are shown in Figures 1, 2, and 3. The figures on 00.1 are "etch hillocks", rather than pits, and according to Honess(6), this phenomenon

Jan 1, 1961

By W. S. Gillam

A need for new supplies of fresh water exists today and in many specific areas that need is urgent. One solution lies in saline water conversion, a problem complicated by cost factors. The principles involved in saline water conversion, the status of development, and the estimated costs (present and future) of several processes are presented. Among the methods discussed are distillation, electrodialysis, and freezing. In general, the costs presented are based on a standardized procedure for estimating conversion costs, permitting a valid comparison among the various processes. The need for new supplies of fresh water and the potential benefits to be derived from an abundant supply of converted water are recognized by practically everyone concerned with water problems. The water supply problem exists today; it is urgent in many specific areas in this country and also in the world, and it will become more acute in the future. One answer to the growing problem of adequate water supplies is the development of new sources. Very significant quantities of brackish underground and surface waters exist in certain areas and an inexhaustible supply of ocean water is available. Thus in many areas water resources can be extended through saline water conversion. Congress recognized the need for new sources of fresh water in 1952 and passed the Saline Water Act, Public Law 448, amended it in 1955, and in September 1958, enacted Public Law 85-883, calling for the construction of at least five demonstration plants. The program is administered by the Dept. of Interior through the Office of Saline Water, and its primary objective is to reduce the cost of converted water produced, whether it be by development of new processes or improvement of known processes. This is a most difficult problem and one that will require several years of prodigious effort. It is difficult—not because of any intricate or new chemistry, engineering, or physics involved—but because of the difficulty in converting water at low cost. Whatever the sources of the saline water, the salts which are held tenaciously in solution must be removed before the water becomes suitable for industrial or domestic uses. Saline water is a relatively simple system of salts dissolved in water. It has certain chemical and physical properties that determine the various methods by which the salts may be separated from the water. The system, although not complex, in most instances, has had countless years in which to reach equilibrium and is, therefore, comparatively stable. Because of its stability, separation of saline solutions requires relatively large quantities of energy. The unique properties of water depend on the fact that its molecules are chemically active. The chemical and physical properties of water are associated with the type of bonding involved in the water molecule. Chemical changes such as hydrolysis, or rusting of iron, involve the breaking of chemical bonds between the hydrogen and oxygen atoms. Physical changes, such as evaporation in a boiler, the melting of ice, or the viscous resistance to flow in a pipe, involve breaking of the hydrogen bonds. (The hydrogen nucleus is so small that it can attract two negative atoms.) Thus water molecules not only combine with molecules of other compounds but even with one another; e.g., each molecule may be bounded to four other molecules. Water molecules cling to the ions of dissolved salt to form water-encumbered hydrated ions and they cling to one another to form entangling networks through which hydrated ions can be propelled only by tearing the networks apart. That is one reason why considerable energy still needs to be expended in our simplest procedures for purifying water. If water molecules did not have this habit of clinging so tenaciously to other molecules, and to one another, it would be easy to push salt ions past the water molecule and get a separation. But the water would not then dissolve salt, so the problem would not exist.' Water when heated evaporates very slowly, relative to other liquids having simple molecules. Vaporization involves the separation of molecules from the liquid, and this means overcoming the attraction between molecules which is due to the hydrogen bonding. The heat of vaporization for water is high; consequently, the boiling point of water is also high. Water boils at 100" C; hydrogen sulfide (H2S) at -60" C; oxygen (02) at -183" C; nitrogen (N2) at -196" C; and methane (CH4) at-161°C, even though the latter has about the same molecular weight as water. Because of these peculiar properties of water, it exists as a liquid on earth instead of a gas such as hydrogen sulfide or nitrogen and oxygen.

Jan 1, 1961

By M. N. Pathasarathi, P. A. Beck, T. J. Koppenaal

EARLIER work1 indicated that in rolled and annealed copper the volume fraction of the cube-texture component may increase on continued isothermal annealing. Merlini found2 that in rolled copper the well-known increase in the amount of cube-oriented material with increasing annealing temperature3 is concurrent with grain growth, which takes place after recrystallization is complete. It was found that both in copper2 and in aluminum4 the texture resulting from primary recrystallization, even if this is followed by some grain growth, may in general comprise, in addition to the cube-texture component, four symmetrical texture components of the general type (123)[412], i.e., components not very far from the ideal orientations of the rolling texture. The volume fraction of the cube-texture component increases on further annealing at the expense of these four components.' The present work was undertaken to study quantitatively the increase in the volume fraction of the cube-texture component in the course of normal grain growth, under varying conditions. Since the grain-gr3wth behavior of A1-Mn alloys has been already investigated in some detaiL5 an A1 + 0.8 pct Mn alloy was chosen for this work, in which the extent of normal grain growth can be effectively controlled by the inhibiting effect of a dispersed second phase. EXPERIMENTAL PROCEDURE High-purity aluminum of the following composition was used: A1 99.997 pct, Cu 0.0004 pct, Fe 0.0005 pct, and Si 0.001 pct. A high-purity A1-Mn master alloy was prepared by dehydrating manganese chloride at 500°C and reacting it with molten high-purity aluminum at 750°C in a graphite crucible.5 The Mn metal reduced from the salt by the molten aluminum goes into solution in the latter. The master alloy? containing 13 pct Mn, was solidified under conditions suitable for minimizing segregation. An ingot of the final alloy, to be used in the experiments, was per pared by melting high-purity aluminum and the necessary amount of master alloy in a graphite crucible, and by pouring the molten alloy into a graphite mold preheated to 700°C through a box containing graphite baffles designed to intercept most of the aluminum oxide films floating in the melt. The melt was then solidified by placing the mold on a water-cooled copper plate and by keeping the top of the mold hot, in order to minimize piping. The 6 1/2 in. long, 11/4-in.diam ingot consisted largely of a single crystal. Chemical analysis showed that there was little segregation from the bottom (0.83 pct Mn) to the top (0.81 pct Mn). Spectrographic analysis of the ingot showed that the impurity content remained essentially the same as that of the aluminum used. The ingot was processed so as to obtain a uniformly small grain size. without banding. The ini-tial steps of rolling in the form of a flat bar and of annealing, down through a thickness of 0.4 in., are shown in Table I. At this point the bar was cut into four sections, each approximately 3 in. long, which were processed separately as shown in Table If. The table also gives the penultimate grain sizes obtained in each section by annealing prior to the final rolling of 90 pct RA. During the final rolling the strips were reversed end to end between passes. Annealing treatments were given in a salt pot furnace, with the temperature controlled to 1°C. All annealing of section "6s" was carried out above the solvus point to avoid the formation of second-phase precipitate. The penultimate annealing was sufficiently short to give a relatively fine grain size in spite of the high temperature. Section "6L" was processed in a similar manner, except that the penultimate annealing was much longer, so as to allow considerable grain growth. Section "4" was given the two final

Jan 1, 1961

By C. S. Finney, John Mitchell

The introduction of ovens for the production of metallurgical coke is believed to be due to L. L. Norton who operated an iron foundry in the vicinity of Connellsville, Pa. Persuaded by his foreman, an English immigrant named Nickols from Durham, L. L. Norton put up a 12-ft square oven which produced coke in 1833. The coal used was taken from a local mine at Mounts Creek. The oven seems to have been used in conjunction with the customary method of coking in mounds. It was in the Connellsville district also, in 1841, that two carpenters, Provence McCormick and James Campbell, formed a partnership with John Taylor, a stone mason, for the manufacture and sale of oven coke. The task of the mason was to construct the ovens, while the carpenters were to build the arks by which the coke could be taken by water to the market at Cincinnati. The following account of the enterprise was given by McCormick: "James Campbell and myself heard in some way that I do not now recollect that the manufacturing of coke might be made a good business. Mr. John Taylor, a stone mason, who owned the farm on which the Fayette coke works now stand, and who was mining coal in a small way, was spoken to regarding our enterprise, and proposed a partnership-he to build the ovens and make the coke and Mr. Campbell and myself to build a boat and take the coke to Cincinnati, where we heard there was a good demand. This was in 1841. Mr. Taylor built two ovens. I think they were about 10 feet in diameter. My recollection is that the charge was 80 bushels. The ovens were built in the same style as those now used, but had no iron ring at the top to prevent the brick from falling in when filling the oven with coal, nor had we any iron frames at the mouth where the coke was drawn. The top and mouth had to be repaired when they fell in. In the spring of 1842 enough coke had been made to fill two boats 90 feet long-about 800 bushels each-and we took them to Cincinnati down the Youghiogheny, Monongahela, and Ohio, but when we got there we could not sell. Mr. Campbell, who went with the boats, lay at the landing some two or three weeks, retailing out one boatload and part of the other in small lots at about 8 cents a bushel. Miles Greenwood, a foundryman of that city, offered to take the balance if he would take a small patent flour mill at $125.00 hi pay, which Mr. Campbell did. He had it shipped here. We tried it, but it was no good, and we sold it to a man in the mountains for $30.00, and thus ended our coke business." So successful did the coke subsequently prove to be in use that the three partners were asked to deliver more. Evidently they had had enough of the coke business, however, for they refused to have anything more to do with it. Few ovens were built between 1841 and 1855, and it is reported that in the latter year, "there were only 26 coke ovens along the river above Pittsburgh". Successful coke makers of these years included Mordecai Cochran, Richard Brookius, and Colonel A. M. Hill. It was the use of coke in 1859 in the Clinton furnace erected by Graff, Bennett and Co. in a plant on West Carson Street, Pittsburgh, that brought the real beginning of the coke-iron era in America. Here the successful use of Connellsville coke as a blast-furnace fuel was demonstrated beyond all possible doubt, and from the year 1859 the coking industry expanded tremendously. The era of beehive coke ovens During the latter half of the nineteenth century and the early years of the twentieth, the major percentage of metallurgical coke produced in the United States came from beehive ovens. It was not until 1893 that the first battery of by-product ovens came

Jan 1, 1961

[Alphabetic Section (Page 689): The letter immediately following the member's name indicates grade: M-Member, A-Associate, J-Junior. The numerals following member's grade indicate year of election. The letter following year of election indicates primary Divisional affiliation: A-Mining & Exploration F-Coal B-Minerals Beneficiation G-Petroleum C-Iron and Steel H-Industrial Minerals D-Extractive Metallurgy J-Council o f Education E-Institute of Metals K-Council o f Economics]

Jan 1, 1961

By E. T. Turkdogan, L. E. Leake

A number of measurements have been made on the vapor pressure of pure iron at 1600°C. Experiments were carried out by the transportation method in which a sample of iron is exposed in a furnace to a stream of pure argon, metered at a predetermined flow rate for a specified period of time. The vapor pressure was obtained from the weight loss of the sample. A detailed diagram of the apparatus used for the experiments is given in Fig. 1. It consisted of a horizontal molybdenum-wire-wound furnace fitted with a recrystallized alumina tube 1 1/8 in. internal diam. The boats, 1 by 3/16 by 1/8 in., were fired in argon at 1600°C to constant weight before use. After this treatment, subsequent heating of the boats to 1600°C gave little or no further change in weight, e.g. ±0.05 mg in 24 hr. The furnace and reaction tube were separately fed with argon from two independent flowmeters. These were connected to a common supply source via an argon purification furnace containing metallic titanium sponge at 700°C, and an anhydrone drying-tower. A rotary displacement-type meter was included in the gas train to provide a direct means of measuring the total volume of gas passed through the reaction tube. The material used was vacuum melted high-purity iron in the form of wire 2mm in diam. The following impurities were present in the iron: 0.008 pct C, 0.002 pct Si, 0.005 pct Mn, 0.008 pct S, 0.001 pct P, 0.01 pct Ni, 0.001 pct Cr, 0.006 pct Cu, and 0.001 pct Al. Samples consisting of three small pieces of this wire were laid end to end in a recrystallized alumina-combustion boat, and were separated by small fragments of alumina. The wire samples were then melted in argon to form spherical beads 2 to 3 mm in diam. After weighing, the boat with its contents was placed on the boat carrier and introduced into the cool end of the reaction tube. The entire furnace system was then flushed with argon for 30 min. At the end of this period, the flow of argon to both furnace and reaction tubes was adjusted to the desired level; then the boat was slid rapidly into the hot-zone of the reaction tube. After a known volume of gas had passed through the reaction tube, the boat was withdrawn quickly to the cool end of the furnace. When quite cool, the boat was removed from the fur-mace and placed in a desiccator for subsequent re-weighing. The semi-micro balance used in these experiments had a sensitivity of 0.005 mg. The above procedure was repeated at several flow rates within the range of 25 to 300 ml per min. The flow of argon in the annular space between the two tubes was at a rate of 300 ml per min in all experiments. During all the experiments the furnace temperature was maintained at 1600° ± 5°C by means of a temperature controller. The temperature of the reaction zone was measured with a Tinsley high precision disappearing filament pyrometer which was initially calibrated against a Pt-13 pct Rh/Pt thermocouple; the errors due to temperature measurements were within * 5°C. RESULTS Assuming that the iron vapor is in the monatomic state, the vapor pressure can be calculated from the weight loss of the sample and the volume of the carrier gas. The results obtained are plotted in Fig. 2 against the rate of flow of argon through the chamber containing liquid iron beads. At low flow rates, the thermal diffusion of iron gives an apparent high vapor pressure, but at high gas flow rates, the carrier gas is not saturated with the vapor, and therefore, low vapor-pressure values are obtained. This is now a well-known phenomenon. There is a distinct inflexion of the curve at about 120 to 160 ml per min rate of argon flow and the vapor pressure of iron within this

Jan 1, 1961

By W. B. Triplett, H. I. Aaronson, G. M. Andes

A detailed morphological study has been made of the pro-eutectoid TiCr, and the eutectoid reactions in a Ti-17.42 pct Cr alloy isothermally transformed at temperatures from 775° through 5561°C. The morphologies of proeute,ctoid TiCr2 were found to be subject to description by the Dube morphological classification system. Grain boundary allotriomo.lphs are the dominant plpoeutectoid morphology throughout the temperature range investigated. lntragranular plates, and especially Widmanstatten sideplates, form only in small numbers. This morphological pattern differs markedly from that of the proeutectoid a reaction in hypoeutectoid Ti-Cr alloys (AIME Trans., 1957, vol. 209, p. 1227; 1958, vol. 212, p. 624), in which plates form prolifically throughout wide ranges of temperature. The eutectoid reaction is nonlamellar in character at 675°C. An increasingly prominent lamellar component develops at lower temperatures. The proeutectoid TiCr 2 and the eutectoid transformations have been studied metallographically in a hypereutectoid titanium-chromium alloy. This investigation was undertaken with the immediate objective of comparing these transformations with their counterparts in hypoeutectoid titanium-chromium alloys, studies of which have been recently completed.1,2 It was also intended, however, to contribute to the general literature on transformations of these types. Especially in the proeutectoid case, this literature is still sufficiently sparse to make difficult the testing of generalizations on the mechanisms of these transformations. TiCr, is the only intermetallic compound in the titanium-chromium system.3-5 The TiCr2 phase field extends to a maximum temperature of 1350°C) and encompasses the approximate composition range of 62 to 68 pct Cr at lower temperatures.3'4 At temperatures below 1000°C, TiCr2 has a MgCu,-type fcc structure, with 24 atoms comprising a unit cell.6,7 Only fragmentary observations on the morphology of proeutectoid TiCr2 have been previously reported. An observation which is of considerable importance with respect to the results obtained during the present investigation was made, however, on anisother-mally transformed alloys with high chromium (48 to 70 pct Cr) contents.3"8 Despite the occurrence of extensive impingement, it is apparent that a substantial proportion of the proeutectoid TiCr, which precipitated in these alloys grew in the form of Widmanstatten plates. Several observations have been made on the eutectoid reaction in hypereutectoid alloys during investigations of the titanium-chromium phase di-

Jan 1, 1961

By C. D. Thompson, D. C. Violetta, C. A. Czako

The mechanics of the continuous sintering process are briefly reviewed and the application of this process for the beneficiation of principal minerals used in making cement is shown. Pilot plant tests using pyrobeneficiation techniques were conducted with mixtures of limestone and shale in various ratios. Results are illustrated and show the percentage removal of carbon, carbonates, sulfur, alkalies, and volatiles as a function of the limestone-shale ratio. Tests with varying quantities of solid fwls, added to mixtures containing limestone and shale in a 4 to 1 ratio, were made to attain optimum elimination of the volatile constituents. Experimental results show that 90 pct of these constituents were removed during the calcination sintem'ng process. The advantages of using the beneficiated material for making cement are discussed with regard to prepam'ng, handling, and clinkering operations. A sintering process for treating raw materials or kiln waste products which contain high amounts of alkaline materials is described. Tests were performed with a high alkaline waste dust mixed in a 1 to 1 ratio with raw cement meal. The data from these tests and others using different halides for aiding alkali removal are evaluated by the alkali content of the cement clinker. Test results showed that the Dwight-Lloyd process could be applied with facility in beneficiating raw materials for cement making. Substantial quantities of deleterious volutile constituents were removed by calcining and sintering techniques. The continuous sintering process has been applied for a number of years as a means of beneficiating minerals for subsequent conversion to merchantable products. The process was developed and first used for nonferrous metallurgical applicatfons. However, it has risen to prominence for ferrous metallurgical applications where last year in the U.S. and Canada nearly 40 million tons of iron ore were treated by grate firing processes. Through the years of process development many investigators have realized the versatility of the sintering process and have directed experiments toward the use of it for applications with nonmetallic minerals. These have included calcining limestone, carbonizing coal, expanding shale, and burning cement raw meal. Today commercial sintering plants produce cement clinker from mixtures of limestone and shale, lightweight aggregate from shale or clay, and calcined products from phosphate shale. The mechanics of the downdraft sintering process have been presented by many authors. In general practice the materials to be agglomated are mixed as moistened fines with a solid fuel and this mixture is spread uniformly on the grates of the sintering machine. The charge is then momentarily directed under an ignition furnace. After ignition a continuous downdraft of air promotes combustion of the fuel and through heat transfer particles become partially fused into a coherent mass. This is cooled from continued draft induced after combustion. Many investigators have shown that distinct zones are formed during the process of sintering iron ores. At the midway point of the sintering process these are prominent and are, respectively, from the top of the bed to the bottom, comprised of a cooling zone of sintered material, a combustion zone of sinter formation, a calcination zone, a drying zone, and a zone of unreacted materials. Completion of sintering occurs near the discharge end of the machine where the firing zone approaches either the grates or grate dressing material called hearth layer. Here the peak draft temperature usually can be noted in the windboxes. The zonal pattern has been illustrated with the use of graphs which show thermal gradients as they progress through the bed of materials during sintering. Fig. 1 shows, in simplified form, thermal gradients existing when clinkering cement on a sintering machine. The thermal gradients illustrated are for periods of initiation, midway and completion of the clinkering process. The occurrence of these zones has importance for the beneficiation of cement raw materials. A research program was performed at the Dwight-

Jan 1, 1961

By C. R. Kuzell

STAFF: Editor, Gerhard Derge Carnegie lnstitute of Technology Schenley Pork Pittsburgh 13, Pa. Editorial Assistant, M. A. Redmerski Production Editor, Otto T. Johnson THE METALLURGICAL SOCIETY: C. C. Long, President; John Chipman, Past-President; J. S. Smart, Jr., Vice-President, T. D. Jones, Treasurer; R. W. Shearman, Secretary. PUBLICATIONS COMMiTTEE OF THE METALLURGICAL SOCIETY: D. J. Carney, Chairman; Robert Maddin, Past-Chairman; J. H. Hollomon, J. H. Jackson, H. H. Kellogg, T. B. King, F. C. Langen-berg, D. L. McBride, W. O. Philbrook, J. S. Smart, Jr., R. L. Smith, J. D. Sullivan, and F. L. Vogel Review and selection of manuscripts is under the supervision of the following Publications Committees: Extractive Metallurgy Division: H. H. Kellogg, Chairman; T. 8. King, Post-Chairmon; R. P. Hermsdorf, W. A. Krivsky, R. E. Lund, C. L. McCobe, Poul Queneou, A. 5. Russell, M. E. Wadsworth, and W. D. Wilkinson. Institute of Metals Division: R. L. Smith, Choirman; P. A. Beck, I. I. Bessen, J. O. Betterton, Jr., R. S. Davis, J. J. Gilmon, R. 8. Gordon, C. D. Graham, Jr., R. W. Guard, J. C. Gurlond, J. J. Heger, M. Hermon, J. N. Hobstetter, H. H. Johnson, Jr., I. R. Krarner, W. C. Leslie, R. A. Meussner, R. R. Nosh, G. E. Pellissier, T. N. Rhodin, A. U. Seybolt, L. L. Seigle, I. S. Servi, P. G. Shewmon, L. Slifkin, J. K. Stanley, C. D. Starr, and J. Washburn. Iron and Steel Division: F. C. Longenberg, Chairmon; H. L. Bishop, C. W. Sherman, J. 8. Wagstaff, and E. Whittenberger. Published bimonthly by the American lnstitute of Mining, Metallurgical, and Petroleum Engineers, Inc., 29 West 39th Street, New York 18, N. Y. Telephone: PEnnsylvania 6-9220. Subscription $20 per year for nan-AIME members in United States and North, South, and Central America; $25, foreign; $5 far AlME members. Single copies, $4.00, single copies foreign, $5.00. The AlME is not responsible for any statement mode or opinion expressed in its publications . . . Copyright 1960 by the American Institute of Mining, Metallurgical, and Petroleum Engineers, Inc. . . . Registered cable address, AlME New York ...Indexed in Engineering Index, Industrial Arts Index, and Chemical Abstracts ... Second class postage paid at New York, N. Y., and Ann Arbor, Mich. Volume 218, Number 4

Jan 1, 1961

By W. N. Poundstone, G. R. Spindler

A comprehensive report on extensive experimentation in degasification of the Pittsburgh Coal seam is presented. Detailed accounts of the procedures and results are given for permeability tests, vertical bore hole tests, measurement of gas flow from sealed drainage areas, horizontal rib hole tests, and water infusion tests. The removal of methane gas from coal seams in advance of mining is not a new idea with mining men—much attention has been given to the possibility for many years. In other parts of the world, a principal concern has been in the recovery and utilization of the gas and a number of successful projects have been developed in Europe and elsewhere. In this country, the principal motivation has been related to the safety aspect with some possible side benefits concerning costs and efficiency in mining as secondary objectives. To date, experimental work in this country has been largely or entirely exploratory to determine bed characteristics with respect to the liberation of combustible gases to investigate or establish the possibility of degasification in advance of mining and as an aid in projecting mine ventilation systems to provide for safe, effective and economical handling of combustible gases liberated during mining. With these objectives in mind, the School of Mines and Engineering Experiment Station at West Virginia University, in cooperation with the Christopher Coal Co. of Osage, W. Va., initiated some experimental work in May 1952 and the project has been more or less continuous since that time. The work has been centered entirely in mines of the cooperating company in Monongalia County, W. Va., and Greene County, Pa. LOCATION AND GENERAL CONDITIONS OF THE AREA The principal mining in the area involved is in the Pittsburgh coal seam which lies at the bottom of the Monongahela series of the Pennsylvanian. The Pittsburgh coal in the area is generally uniform in its structure and physical characteristics. The bed thickness averages about 7 to 8 ft and the coal has a characteristic blocky structure as the result of pronounced face cleats and definite, but somewhat less pronounced, butt cleavage. It is a medium volatile coal, averaging about 37 pct, and is marketed principally as a steam fuel and for metallurgical purposes. The Pittsburgh coal outcrops along the Monongahela River and dips gradually, but not uniformly, slightly north of west (about N75°W). The westward extensions of the bed, from the areas contiguous to the Monongahela River which have been heavily mined, constitute the principal reserves and are all well below drainage with the depth of cover increasing with the distance from the river. In general, with deeper cover, it may be expected that methane liberation will be more of a problem in future mining as compared to areas mined previously; therein lies the interest in possible de-gasification in advance of mining. Fig. 1 shows the Pittsburgh coal area in the vicinity of Morgantown in Monongalia County, W. Va., and Greene County, Pa., in which the experimental work discussed is located. Fig. 2 shows the contours on the Pittsburgh coal in the test area. It will be noted that the first two bore holes for the experiments were at the edge of a bench or terrace with considerable change in the gradient in the immediate vicinity of the test holes and that the same general condition applies to later test areas. Mining is intensively mechanized in the area and in the mines involved in the experimental work with corresponding rapid advance of working faces a typical characteristic. In the areas now mined the total methane liberation ranges from moderate to relatively heavy, but the actual face liberation is extremely variable and may range from practically

Jan 1, 1961

By J. L. Gillson

The word "other" in paragraph 4, line 11, column 1, page 205, should read "over;" the correct version of reason 2, this paragraph, is: 'L. . . 2) to evaluate the usefulness of certain geo-chemical techniques, V. C. Kennedy and S. W. Hobbs of the USGS had already studied the distribution of copper, lead, and zinc in the soils (both in background areas and over veins) and in the water and plants, providing a criterion for measuring the magnitude and effect of soil contamination; ...9 On page 206, in the top left hand corner of Fig. 1 (in the area bounded by 47°35' and 116°10), the reference to Fig. 3 is incorrect. The area of Pine Creek, South Fork Coeur d'Alene River, and portion of Big Creek (the area which includes, from left to right, Kingston, Pinehurst, Smelterville, and Kellogg) should be identified as that of Fig. 2A. The headings for columns 1, 3, and 4, Tables I and 11, page 209, column 2, were reversed when the paper was printed. The corrected tables are:

Jan 1, 1961

By B. J. Kochanowsky

The idea of a portable crusher is not new. Many such crushers are available but they are small and designed for construction work. For many years the author has suggested, both in this country and in Europe, the building of larger portable crushers intended expressly for use in quarries or open pits. Although not applicable under all conditions, there are mining operations where a mobile crusher arrangement could be more profitable than the facilities now used. The primary use of a portable crusher, i.e., a crusher mounted on crawlers or tires, in the rock and mining industries is to reduce costs by permitting the substitution of conveyor belt haulage for truck or track haulage. The usual sequence of operations in surface mining is drilling, blasting, loading, haulage, and crushing. Haulage is normally accomplished by truck or track-mounted cars, the latter method being used for the longer distances. However, by using a portable crusher in the pit, the sequence of operations would be changed so that the crushing stage would occur before haulage (Fig. 1). Such a sequence would permit the use of conveyors to replace the more expensive truck or track haulage methods. Since most quarry and open pit operations normally require a crushing stage, the only additional costs incurred will be due to the investment required to purchase or construct a mobile arrangement for a crusher. But this factor has to be weighed against the advantages to be gained by conveyor haulage. As shown in Fig. 2, transportation of material by belt conveyor over short distances is less expensive than by truck. The inclination of the belt has no effect on belt speed; consequently, the hourly tonnage moved remains the same. Conversely, the output rate of trucks as expressed in tons or ton-miles per shift decreases proportionally to the haulage speed, which is considerably slowed by the steepness of the road (Fig. 3, left). Although maximum possible grades and maximum economic grades of haulage are greater for a belt than for a truck (over the same total lift), the longer haulage distances favor the use of trucks. Although power consumption for hauling on a grade increases for both conveyances, the rate of power consumption increases faster for trucks than for conveyor belts (Fig. 3, right). Since the output rate and related fixed costs are affected by the travel speed, total haulage costs with trucks would increase with the grade more rapidly than the similar costs of conveyor belts (Fig. 4). Travel distance, road grade, speed, size and number of pieces of equipment, efficiency of operation, and many other factors affect such haulage costs. In general terms it can be said that the shorter the distance, the steeper the grade, and the greater the output, the more advantageous the belt becomes in comparison to truck or track haulage. In addition to potential cost savings in haulage procedures, a portable crusher would allow better utilization and performance of shovels. Loading operations would not be interrupted as often by the necessity of waiting for cars or trucks. Unfortunately, the application of belts in open pits for haulage from bench sites is generally not practical under existing conditions because a belt fed directly by a mechanical shovel can be torn, damaged, or worn out quickly by the large rock fragments falling on it during loading. However, by using a mobile crusher this situation can be avoided. As shown in Fig. 1 (b), the shovel feeds rock into the crusher located behind it. The crushed material is initially transported by an extensible and/or movable belt, thence by a longer stationary conveyor to the plant where the material is subjected to further treatment by secondary crushing, screening, etc. The first-mentioned conveyor, needed to bridge the distance between the shovel and the stationary conveyor, is necessarily variable in length owing to the continuous movement of the shovel and the desire to keep the stationary belt at a safe distance from the bench during blasting operations. The remarkable part of mobile crusher operations is the extra-ordinarily high output per man-shift, the low maintenance and power requirements for haulage, and the increased output of the loading shovel. A cement quarry which has been using a portable crusher and conveyor since 1956 requires only three men to operate the shovel and crusher and to transport the crushed rock by belt from the quarry face to the screening plant. If truck haulage

Jan 1, 1961

By S. J. Noesen, J. R. Hughes

Several four-inch-diameter tungsten ingots were arc melted in vacuum or in hydrogen atmospheres. Melting pressures, melt-off rates, effect of atmospheres, and other pertinent factors were examined. Two of these ingots were extruded at 1650°C. Subsequently, forging and rolling were carried out at lower temperatures. For a 60 per cent area reduction by rolling, a one-hour recrystallization temperature of 1250°C was obtained. This temperature is considerably lower than those reported in previously published work, and can probably be attributed to the extreme purity of the as-cast ingots (N, H, 0 all less than 1 ppm). EVER since W. D. Coolidge, in 1909, described his process for producing tungsten metal of high density and good workability via the powder metallurgy tech-

Jan 1, 1961

By A. H. Daane, B. J. Beaudry

The yttl-irtm-nickel system has been investigated by metallo-graphic, thermal ard X-ray methods. There are nine intermetal-lic compounds present: Y3Ni, Y3Ni,, YNi,, YNi,, Y,Ni,, YNi,, and Y,Nil, which rodergo peritectic decomposition and YNi and YNi, which melt congruently. There are eutectics at 34.8, 57.5 and 93.3 at pct Ni which melt at 805°, 950 and 1285 C, respectively. Crystallographic data are given for YNi, YNi,, YNi,, YNi5and Y,Ni,. The terminal solid solubility is low. In recent work by Fisher and Fullhart' in which yttrium crucibles to be used for containers of uranium-chromium eutectic were clad with a high nickel steel, a low melting phase formed where the yttrium was in contact with the steel. To investigate the cause of this phenomenon, Daane, et al. made a survey study of yttrium systems with chromium, manganese, iron, and nickel and found an 18 wt pct Ni (weight percent) alloy to melt at approximately 950°C. voge13 in a study of the systems of cerium, lanthanum, and praseodymium with nickel found six compounds of the same formula in each system, i.e., R3Ni, RNi, RNiz, RNi3, RNi4, and RNi5. Since there is a great similarity between yttrium and the rare earths, compound formation was likely to occur also in the yttrium-nickel system. voge13 observed that the ability of transition metals to form compounds with the rare earths diminishes in the order nickel, cobalt, and iron while no compounds are formed with manganese, chromium, and titanium. Available data on yttrium systems with these elements indicate similar behavior, except that a slightly greater tendency toward compound formation is apparent. Simple eutectics with limited solid solubility have been found in the yttrium-titanium4 and yttrium-chromium5 systems, but at least one compound is present in the yttrium-manganese system.' In the case of yttrium-iron, at least three compounds are present,5 while only two are present in the cerium-iron,' and no compounds are present in the lanthanum-iron5 system. On the basis of both the trend in the alloying behavior of yttrium and rare-earth metals with the first transition series metals and the large number of compounds in the cerium-nickel system, one might expect six or more compounds to form in the nickel-yttrium system. A consideration of Hume-Rothery's rules of alloying based on size factor, electronegati-vity, and valence predicted low terminal solid solubility and possible compound formation. The present study was undertaken to confirm these predictions of

Jan 1, 1961

By L. Sturkey

Quantitative X-ray diffraction studies of the precipitation of thorium in a Mg + 3.3 Th + 0.51 Zr alloy (HK31A) in both the as-cast and cold-worked states show that the precipitation may be described by f = 1 - e(t/T)1/2 over most of the aging period. The effects of cold work and temperature changes are determined. The precipitation of tile equilibrium Mg-Th compotund is Preceded by the formation of a transition phase of higher thorium content, with the cowposition Mg2Th and with a Laves-phase structure. Thorium-containing alloys of magnesium have assumed considerable commercial importance, especially for applications requiring exposures to temperatures greater than 500°F for appreciable lengths of time. The principal commercial wrought alloys in this system are HK31A, containing nominally 3 pet by weight thorium and about 0.7 pet by weight zirconium: and HM21A. containing 2 pet by weight thorium and 1 pet by weight manganese. These two alloys retain a high level of properties even after exposures of 100 hr at 600°F, while the more common alloys containing aluminum and zinc are badly overaged by these conditions. Therefore, in order to obtain some insight into the mechanism by which thorium produces high temperature stability in these wrought alloys, it seems desirable to investi- gate the effect of temperature and mechanical working on the precipitation processes involving thorium. Since the scattering power of a thorium atom for CuKa X-ray radiation is about ten times that for a magnesium atom, the magnesium alloys containing about 3 pet by weight thorium are ideal for quantitative measurements by X-ray diffraction of the amount of Mg-Th compound present at any time. Such quantitative measurements should be of theoretical importance in the study of the effects of time, temperature, and deformation on precipitation and precipitation hardening. Of the two commercial alloys, HM21A and HK31A, the latter is certainly the most suitable for study: In the Mg-Th-Zr2 system, only Mg-Th compounds need be considered, since no ternary compounds or binary Th-Zr3 and Mg-Zr4 compounds exist. The Zr is added to this alloy as a grain refining agent and probably plays a secondary role in precipitation. On the other hand. thorium and manganese form many

Jan 1, 1961

By Robert W. Shearman

An historical record of the history of iron-and steelmaking in the United States has long seemed a desirable project to many in The metallurgical Society of AIME. Over a period of five years, experts in their fields have been asked to put down on paper their knowledge. The series of historical articles has been published in JOURNAL OF METALS, beginning with A. B. Wilder's article in 1956, marking the first one hundred years of Bessemer Steelmaking. The Electric Furnace Committee honored the first half-century of the use of the electric arc furnace in America during their 1956 Conference, and S. B. Casey, Jr., wrote an appropriate article for JOURNAL OF METALS. The historical series was well underway. Articles soon followed on the history of the blast furnace, on the open hearth furnace, and on ferro-alloy manufacture. The final need was an authoritative article on coke ovens. The publication of the five-part article by C. S. Finney and John Mitchell this summer has concluded our series (but not the march of progress). We now present, between two covers, a comprehensive historical review, the work of 13 authors. We are hopeful that this book will receive a welcome among ironmakers and steelmakers. and that it will be a valuable reference for home or office library. We hope also that students will find the material helpful in their studies of this most important of American industries. Perhaps also, the historian of Americana will learn something new in searching through these pages. We are indebted to our authors who have spent much time on historical research, and to their companies who have supported their endeavors. We acknowledge the support of the National Open Hearth Steel Committee and of the Blast Furnace. Coke Oven, and Raw Materials Committee in jointly assuming the financial risks in publishing this book.

Jan 1, 1961

By F. C. Schora, H. P. Meissner

COUNTERCURRENT staged processes involving chemical reactions between solid and gas streams are becoming more common. Such operations are generally carried out in a series of fluidized beds with each bed acting as a stage. Fig. 1 is a schematic illustration of a series of stages located in a single column, with a solid stream moving down through this column from stage to stage counter to a rising gas stream. The reduction of iron oxides with hydrogen and carbon monoxide is one of the reactions which can be advantageously carried out in such a countercurrent system. Calculation of the performance of a countercur-

Jan 1, 1961