Search Documents

By McKew M, OÆRegan

Rapid access longwall mining' or 'longwail punch mining' is a proposed extraction method whereby longwall gate roads are driven into a seam directly from an opencut highwall. The longwall panel thus formed is retreated back to within 40 m of the highwall providing an extremely simple, reliable and therefore highly productive longwall mining system. The concept is of particular benefit for the recovery of isolated pockets of coal (adjacent to a highwall) not easily accessible from a conventional underground mine. As panel gate roads are driven directly from the open strip, minimal delays are incurred between the end of open cut and start of underground production, allowing the method to bridge the gap between open cut mining and a total underground commitment. The study was specific to the Bowen Basin, and given the likely conditions, no significant operational or geotechnical hinderances to the concept could be identified. It was therefore concluded that longwall punch mining would not expose the operator to any additional risks above that normally associated with the introduction of longwall mining. Thus, longwall punch mining is an attractive option, both operationally and financially, for open cut mines reaching their maximum economic Death.

Jan 1, 1988

By Rennie J. W

In the first five years of longwall mining at Pacific Colliery, special techniques of goaf sealing, gas drainage, goaf edge ventilation and goaf sampling were developed and used to o crcome the concurrent problems of spontaneous combustion and high methane emissions. The English-inspired back-return face ventilation system was modified to suit Australian mining methods and was first used as part of a 'Y' ventilation system and more recently was used with a 'U' system of ventilation. In conjunction with this ventilation system, the maintenance of a sealed goaf area was an essential element in the control of the spontaneous combustion in the goaf.

Jan 1, 1988

By D T. Ribeiro, J F. C L Costa, J C. Koppe

Drilling and sampling are responsible for most of the costs during mineral exploration, especially in multi-elements and polymetallic deposits, such as iron, manganese and bauxite deposits. On these deposits, often it is necessary to estimate multiple attributes at several granulometric fractions, ie distinct particle sizes. This paper investigates the effect of sampling at a close spacing grid only the head grades for the multiple chemical species in iron ore deposits. The remaining required data at the various grain sizes are sampled at a sparse grid. The derived geological model is checked for precision and accuracy comparing the output obtained against a model obtained using a complete isotopic data set including head grades and chemical analysis at each granulometric fraction analysed at all sampled positions. Among the several tested alternatives, the best procedure for dealing with the posed problem involved utilising the correlation coefficients between the grades at distinct fractions to obtain an isotopic database prior to interpolation. Cokriging was the method used, based on the intrinsic coregionalisation model. Estimates were obtained with the quality needed for the proposal of the study. Results showed that at least 50 per cent of the blocks were estimated with errors less than ten per cent relative to the grades obtained at the reference model, using only 15 per cent of the granulochemical data employed to obtain the reference model. The methodology also preserved the correlations between the attributes in their several granulometric fractions on the estimated model.

Sep 26, 2011

By P Mulvey, M Stuckey

"Inter-aquifer leakage due to fractures caused by coal seam gas extractions or longwall mining is an important issue for both the gas and coal industries. Currently, predicting stress induced macro-porosity associated with hydraulic fracturing, depressurisation via dewatering or collapse of overlying seams to infill a void left by longwall mining, is problematic. If fractures can be located the fracture can be sealed. Locating fractures is difficult. The non-geophysical approaches to locate fractures has been to consider the mixing of different waters, particularly that of more recent shallower groundwater with older deeper groundwater, via differences in radio-isotopes integrated with geochemical models to predict likely mixing of waters. This approach is applicable under appropriately complex settings; however, it is an expensive technique and is based on the assumption that the daughter isotopes are equally non-reactive which may not always be the case.Potentially a cheaper and faster technique is to consider integrating geochemistry (mineral weathering) and hydrogeology. The chemistry of groundwater, controlled by the weathering of primary rock?minerals and?formation of secondary minerals, can not only be differentiated between geological strata but also within strata as different stages in weathering results in differing impacts on water quality (ie different reactants).Field analysis of pH, electrolytic conductivity (EC), oxidation reduction potential (ORP) and dissolved carbon dioxide together with laboratory analysis of dissolved constituents characterise the chemistry of the water. Collection of rock samples at the time of drilling for bore installation can provide the (only) opportunity to assess the media in which the groundwater resides and migrates through. An assessment of aquifer matrix chemical makeup, via bulk sample chemical analysis, X-ray diffraction (XRD) and petrographic analysis can achieve this.The chemistry of groundwater is dependent on the water velocity. Water at deposition and post-diagenesis dissolution of minerals by hydrolysis and oxidation will result in equilibria of the dissolved phase with the solid phase. Post-depositional fractures caused by either tectonic activity or weathering alter the rate of weathering and thereby the geochemistry. Slow water flow in microfractures results in water in equilibrium with the rock minerals. Faster flow in larger fractures results in water being in disequilibria with rock minerals.Fractures can alter groundwater chemistry by two pathways: changing groundwater velocity, which changes the rate of hydrolysis or oxidation mixing water from different geological strata.Both pathways cause subtle changes in the water chemistry.It is however, the dissolved phase chemical data, which can be observed over time at individual locations and/or at a point in time along a flow path, which allows the hydrogeologist to ælook up-gradientÆ and locate the zone of leakage. Hence, influences on rock/groundwater chemistry, from anthropogenic sources to natural mixing of waters, can be assessed via appropriate interpretation of geochemistry, hydrogeochemistry and flow data.This paper will use the example of the geochemical and hydrogeological characterisation of aquifers within the Hawkesbury and Bulgo Sandstone of the Southern Coalfields to the south of Sydney in New South Wales to demonstrate this approach.CITATION:Stuckey, M and Mulvey, P, 2013. Looking for fractures - integrating geochemistry with hydrogeology to find inter-aquifer leakage above dewatered or collapsed coal seams, in Proceedings Water in Mining 2013, pp 99-108 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 26, 2013

By Sneyd R. J, Walton M. C

In early 1987 Minproc acquired a license from the inventor to engineer and construct acid plants incorporating the Fattinger technology. The process offers a simple and reliable method of producing sulphuric acid from metallurgical off gases at significantly lower capital and operating costs than the more familiar contact process. The process also offers the simultaneous production of nitric acid, if the NOx content of the off gases is high enough. A development of this latter process has other applications within the minerals industry, particularly in conjunction with refractory gold ore preoxidation.

Jan 1, 1989

The basic make-up of the majority of currently produced bulk explosives has changed little in the last 20 years. These explosives would be described as mature in a life cycle analysis. Therefore these explosive products and the practical rules for their use are well understood and well established. In recent years there has been interest in low density explosives, predominantly due to ammonium nitrate shortages and the associated increase in the cost of explosives. In the use of low density explosives some of the practical rules for the more commonly used bulk explosives do not apply. Therefore a shift in the thinking among users is required. At a number of mines low density explosives have been trialled or are being used, utilising the practical rules that apply to bulk explosive products. This has led to poor blast results in many situations. These poor blast results have often then led to a reduction in the use of low density explosives at the mine. This reduction does not acknowledge the advantages that can be gained from this product in the area of reduced cost of mining. This paper looks at low density explosives and discusses how and why these products work. Included in the paper are some practical ideas and examples of how low density explosives can be effectively used at the mine site.

Jan 1, 2007

Whilst the fossil fuel-based power industry moves towards carbon capture and storage (CCS) or so-called 'geosequestration', the minerals industry should adapt to reap the benefits of the new technology. If CCS becomes viable, the door is open to potential key developments in mineral processing. For example, truly continuous steelmaking could at last be realised using natural or manufactured gas combined with generic melt circulation. Iron ore fines would form a thin molten layer moving countercurrent to the gaseous reductant on one side of a melt circulation loop with efficient post-combustion without deleterious effects of slag accumulation on the other. This eliminates oxygen steelmaking because carbon has no access to the circulating molten iron. Steelmaking merely requires addition of the appropriate low level of carbon and in-line impurities removal to meet product specification. Concerning non-ferrous smelting, nothing short of virtually zero gas emission will be acceptable in the future. For dolomite-hosted Zn/Pb sulfide ores, typified by those in the Carpentaria region of Northern Australia, the way forward proposed is sulfur fixation at the mine site employing the highly exothermic reaction of SO2 with dolomite, followed by encapsulation of sulfated dolomite in fused ore slag. This releases enough energy for direct ore smelting to individual metal products. However, without CCS the strategy would be unacceptable because of greenhouse gas emissions. The scheme is advocated for direct ore smelting at McArthur River. As a result, the environmental problems of disposal of flotation tailings are avoided. Also, highly energy intensive ultra-fine grinding is eliminated, as indeed froth flotation itself, with overall very significant energy savings and exceptionally high increases in metals recovery. Zinc and lead recoveries approaching 99 per cent are predicted to be entirely feasible.

Sep 13, 2010

Magnetic separation using particle rotation in a continuously rotating magnetic field offers very low to insignificant non-magnetic particle entrapment, and precise magnetic fractions. The precision of rotating magnetic field separations makes the method ideal for dry laboratory magnetic analysis work, where conventional laboratory magnetic separators can give misleading or uncertain data. The very low entrapment characteristics make the method ideal for entrapment-critical separations within the diamond exploration industry or in gold recovery. A single wet rotating magnetic field (RMF) unit is able to achieve a cleaner separation (at similar or better recovery rates) than a three-stage separation using conventional wet drum separators. The RMF separator is able to work effectively at particle sizes below 50 ¦m, and RMF separation could, at least in theory, be used down to single domain particle sizes. Rotating magnetic field (RMF) separation is carried out by magnetically spinning the particles at frequencies up to 300 Hz. The particle rotation itself may be used to roll the particles out of the separator. At angular velocities of 100 Hz, magnetic flocs are unable to form, and any entrapped particles are energetically expelled. In an RMF separator, the outer drum can be stationary while the inner magnet rotor rotates, allowing, for example, the injection of cleaning water underneath the separating magnetics to help remove small suspended non-magnetic particles.

Jan 1, 2000

By H Sofatzis, J Kinal, J Siliezar, B Kirkwood

Ernest Henry Mining (EHM) is a copper, gold and magnetite mining and processing operation located 38 kilometres north east of Cloncurry in the Mount Isa - Cloncurry mineral district of north west Queensland, Australia. The EHM ore body is an iron oxide copper gold deposit with an average grade of 1.1 percent copper, 0.5 g/tonne gold and 22 percent magnetite.At the end of 2009, after a series of promising laboratory test work, EHM converted the ball mill media charge from forged steel to high chrome media. Laboratory test work also indicated that with the use of high chrome media, the pH was able to be reduced with no negative impact on plant performance. At high pH values (above 10.5), the forged media is passivated, so as the pH of the system drops the media corrosion rate increases and floods the system with corrosion products, affecting flotation. As the high chrome media is much more inert, pH has less of an effect on copper flotation response.This paper provides an overview of the effects of reducing the pH in the EHM copper rougher flotation circuit. The pH in the roughers was dropped from 10.6 to 9.6 to determine the impact on the rougher performance and the subsequent performance of the whole copper flotation circuit. It was found that there was a slightly increased improvement in copper recovery and no statistical change in either the rougher or final copper concentrate grades for copper and gold.With the reduction in pH, there was a noticeable reduction in lime usage from 0.85 kg of lime per tonne of ore processed to 0.55 kg/t. This reduction in lime is equivalent to approximately $700,000 per annum at current production rates.CITATION:Kirkwood, B, Kinal, J, Siliezar, J and Sofatzis, H, 2013. Low pH trial in the Ernest Henry Mining copper rougher flotation circuit, in Proceedings MetPlant 2013 , pp 371-377 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By Moxon N. T

A series of low shock energy water resistant emlulsion based explosives have been developed by combining inert materials, such as Perlite P500, into the formulation. The material handling, water resistance and explosive properties of these mixtures were determined as a function of inert additive type, density, charge diameter and emulsion base. Of the emulsion bases tested Emulite produced the best and most stable low density mixtures ranging in density from 0.8 to 1.35 g/cm3 producing velocity of detonations (unconfined) ranging from 3000 to 5500 nits. The mixtures could be detonated successfully at these densities at diameters as low as 25mm. Low shock mixtures formed by combining Emulite with Perlite P500 were successfully trailed at the Cadjebut zinc mine in Western Australia. The performance of the explosive, at three densities, was monitored using both continuous and point to point VOD techniques. The fragmentation produced by the blasts were compared by photographic analysis. During this trial the low shock emulsion mixtures were shown to be as effective as the currently used explosives (packaged emulsion) at a significantly reduced cost.

Jan 1, 1990

By C Li

Removal of gangue minerals from ilmenite concentrates can beaccomplished by relatively low temperature roasting in controlled gasatmospheres to selectively enhance the magnetic separationcharacteristics of the ilmenite. At roasting temperatures below 800¦C the magnetising reactions are often not consistent with phase equilibria considerations. Metastable phases can nucleate and control the roasting products. In weathered ilmenites the phase assemblages and microstructures in the altered ilmenite grains can influence the roasting reactions. In this paper we give an overview of the phase chemistry of chemically weathered ilmenites and of metastable phases formed by low temperature roasting. We also report the results of roast experiments conducted in a neutral gas atmosphere. Major increases in magnetic properties after short roasting times at low temperatures were obtained for a range of ilmenite concentrates. For example heating a secondary ilmenite concentrate from Western Australia for 15 minutes in nitrogen at 600¦C gave an increase in the three kilogauss magnetic fraction from three to 92 wt per cent. The solid state phase changes accompanying the inert atmosphereroasts were characterised by combining elemental analyses withquantitative phase analyses of the ilmenite concentrates and their roast products. It was found that the phase reaction that is principally responsible for the increase in the magnetic properties of weathered ilmenites involves a transformation of disordered ferrous-containing pseudorutile to an ordered ilmenite-hematite solid solution containing typically ten to 35 mole per cent of the hematite component. Examples are given of the application of the inert atmosphere roast to effect separations of ilmenite from gangue minerals.

Jan 1, 2001

The effect of temperature, time and SO2 concentration in the atmosphate have been studied for a complex Pb-Zn concentrate, which contained four sulphides and some organic material, in order to determine optimum roasting conditions. Under static roasting conditions virtually complete sulphation was achieved after roasting at 650¦C.2 hours in 10% SO2 in air. Both zinc ferrite and zinc silicate were observed to form early in the roasting, but continued exposure to SO2 -containing gases caused decomposition of these as the roasting time increased. Water and acid solubilities of iron, silica, calcium, magnesium and aluminium in the calcine were determined, as a function of roasting time, temperature and atmosphere composition.

Jan 1, 1970

Productivity of mines can be improved by taking fewer, but larger blasts. The initial blasts taken in starting a mining block are restricted by the low amount of void or space to fire into. Block cave mines are using a blasting technique to blast areas that have less than the normally accepted minimum void to establish drawbells for their orebody development. This technique used in block caving mines can be used to improve productivity in mining operations that utilise other mining methods. Some larger blasts have been done in mines, using open stoping methods, which have had void ratios as low as 13 per cent. This has been possible with the use of the explosive gases to transport the broken rock out of the area normally considered to be available to blasts. This trapping of the explosive gases in the broken rock has allowed rock to be moved over 30 m, horizontally, to allow for more void to be available in the blast area. This gives the necessary void ratio allowable to fire larger blasts. This paper will discuss the blasts where this technique has been used in mines to increase the tonnes fired in low void situations. It will also discuss where this type of blasting may improve the productivity of underground mines. Figure 1 shows the how explosive gases have enabled the broken rock to flow out of a draw point without the typical air blast and fly rock that would normally cause a rope suspended sign to be damaged beyond use.

Jan 1, 2008

By King R. L

Low-enthalpy geothermal groundwater resources occur at relatively shallow depths in the Upper Cretaceous/1'ertiary sedimentary sequence in the on-shore Gippsland Basin. The main stratigraphic unit containing hot groundwater is the Latrobe Group. Groundwater temperatures in the range 30 to 70¦C have been recorded from depths between 500 and 1000 m. The hottest groundwater is in the Latrobe Valley and Lake Wellington depressions. Geothermal gradients in these areas range from less than 2¦C/100 m to over 10¦C/100 m (compared to a world average of about 3¦C/100 m). A number of theories have been advanced to explain the geothermal anomalies including exothermic reaction such as oxidation of coal, mixing with deeper, hotter groundwater and high geothermal fluxes along fault zones. Variations in geothermal gradients can also result from type and thickness (and hence thermal conductivities) of the sedimentary pile, depth to consolidated basement rocks, and influence of groundwater flow patterns including proximity to recharge zones. The hot groundwater in the Gippsland Basin has substantial potential as a source of energy for direct heat applications such as process heating, space and water heating for buildings, and agricultural and aquaculture. Geothermal energy has a number of environmental advantages over traditional sources of energy. It is clean, safe, causes minimal land disturbances and in most cases is naturally renewable.

Jan 1, 1992

By B Clements, R Dunne, J Dioses, S Hart

In April 2003 plant upgrades in the æLow GradeÆ Cadia Hill circuit were undertaken in order to improve concentrate quality and metal recoveries from the flotation circuit. The major changes involved: circuit reconfiguration to allow all concentrates to be reground to less than 38 ¦m prior to final cleaning; increasing ball charge in the regrind mill to fully utilise all of the installed power; desliming of the cleaner scavenger concentrate to improve the circuit water balance; and the inclusion of a gravity concentrator in the regrind circuit to recover more free gold to bullion.Once the flotation circuit had stabilised under the new operating conditions concentrate launder modifications and increased froth crowding on the scavenger flotation cells permitted the introduction of stronger collectors without compromising concentrate quality or circuit stability.Twelve months on, the copper concentrate grade has increased by two per cent and metal recoveries increased by three per cent and seven per cent for copper and gold respectively. The project capital outlay of approximately $2.0 million has been repaid in less than three months. This paper will review the project from the design, construction and commissioning perspective as well as the subsequent debottlenecking exercise that was required to eventually yield the full benefits of this upgrade.

Jan 1, 2005

By J L. Mauk

The Gladstone Hill area hosts epithermal veins similar to those at Martha Hill, which is less than one kilometre away. There are several vein types in the Gladstone Hill area including (1) pyrite-marcasite, (2) quartz, (3) base metal sulfide, and (4) calcite. Pyrite veinlets formed first, whereas the quartz and carbonate veins formed later. The base metal sulfide vein occurs at depth and is predominantly comprised of quartz and chlorite intimately intergrown with pyrite, sphalerite, galena, and rare chalcopyrite. Platy calcite and massive calcite veinlets were the last vein types to form. Several vein textures occur in the Gladstone Hill area, including colloform and crustiform banding, lattice-bladed, zonal, comb, massive and feathery textures. Crustiform banded veins are the dominant texture and contain variable gold-silver grades. Colloform banded veins consist of ubiquitous quartz and minor chalcedony with gold grades as high as 60 g/t. The lattice-bladed texture forms from the deposition of calcite, which has been replaced in many samples by quartz, indicating that boiling and later cooling has taken place. Unreplaced platy calcite only occurs at deeper levels (>300 m). Zonal and comb textures are preserved in quartz and late-stage amethyst veins. Feathery textures within quartz are commonly associated with breccias and some colloform banding, and with significant Au-Ag grades.   The homogenisation temperatures (Th) of primary and secondary inclusions in quartz, amethyst and platy calcite range from 166 to 274¦C, with salinities <1.3 wt% NaCI equiv. The presence of vapor-dominated inclusions and primary fluid inclusions in platy calcite suggests that boiling occurred intermittently throughout deposition. The veins formed under a relatively flat lying paleowater table that occurred 280 - 300 m above sea level. The fluids involved in vein formation were alkali chloride in composition and low in CO2.

Jan 1, 2001

By C Li

Removal of gangue minerals from ilmenite concentrates can be accomplished by relatively low temperature roasting in controlled gas atmospheres to selectively enhance the magnetic separation characteristics of the ilmenite. At roasting temperatures below 800¦C the magnetising reactions are often not consistent with phase equilibria considerations. Metastable phases can nucleate and control the roasting products. In weathered ilmenites the phase assemblages and microstructures in the altered ilmenite grains can influence the roasting reactions. In this paper we give an overview of the phase chemistry of chemically weathered ilmenites and of metastable phases formed by low temperature roasting. We also report the results of roast experiments conducted in a neutral gas atmosphere. Major increases in magnetic properties after short roasting times at low temperatures were obtained for a range of ilmenite concentrates. For example heating a secondary ilmenite concentrate from Western Australia for 15 minutes in nitrogen at 600¦C gave an increase in the three kilogauss magnetic fraction from three to 92 wt per cent. The solid state phase changes accompanying the inert atmosphere roasts were characterised by combining elemental analyses with quantitative phase analyses of the ilmenite concentrates and their roast products. It was found that the phase reaction that is principally responsible for the increase in the magnetic properties of weathered ilmenites involves a transformation of disordered ferrous-containing pseudorutile to an ordered ilmenite-hematite solid solution containing typically ten to 35 mole per cent of the hematite component. Examples are given of the application of the inert atmosphere roast to effect separations of ilmenite from gangue minerals.

Jan 1, 2001

The purpose of the Lower Lea Valley Cable Tunnel project is to relocate the overhead power lines circuits, which currently cross the proposed site for the 2012 London Olympics in East London. This was the first contract to be awarded as an Olympic project and is on the critical path for the proposed Olympic Park as the construction of the Olympic village, stadium and other venues cannot begin until the tunnels are complete, the cables installed and the overhead power lines removed. The tunnelling works for the scheme include two parallel tunnels between Hackney and West Ham. Each tunnel is approximately 6 km in length. One tunnel is 4.15 m ID and connects the National Grid substations. The other is 2.82 m ID and connects the EDF Energy substations. The tunnels were constructed through mixed ground using four earth pressure balance tunnel boring machines. These were driven simultaneously from two drive shafts within a single site. The 12 km of main tunnels were constructed within a year from start to finish, with completion in June 2007. The shafts range between 6 m and 15 m ID. These were constructed using a combination of caisson sinking and underpinning techniques. Dewatering was adopted to suit the groundwater conditions.Other works include the design and construction of the head house buildings, cable and ventilation culverts, mechanical and electrical (M&E) installations and all associated works. In addition to the above, a further 1 km of tunnel and two shafts were added to the project scope connecting the EDF Energy tunnel to the substation at Bow. These additional works provided further challenges to the project to ensure that these works were constructed within the program constraints for the 2012 London Olympics. This involved refurbishing one of the tunnel boring machines from the main EDF Energy tunnel drives and relaunching the machine to construct the Bow tunnel. The Bow tunnel was constructed within two and a half months, with the tunnel boring machine breaking through in August, ahead of schedule. The main challenge presented by this project is the program constraints. This project outlines the requirement for team work between the client, stakeholders, contractor and designer in order to provide program certainty. A close working relationship between the contractor and the designer is required to provide value engineered, time-saving solutions to mitigate the risks associated with the design and construction program.

Jan 1, 2008

By Grant BPM

The lower levels at the CSA Mine have been developed to mine reserves between theNo.7 level and No.9 level.Work on major excavations for the project began during 1982 with the develop-ment of the crusher chamber, on No.9 level. The brows and walls were pre-dowelled to improve stability before mining by mass blasting techniques.At the same time work commenced on theextension of No.2 Shaft from No.7 level toNo.11 level. The shaft was stripped, using hand held drilling, to a raise bored holeand concrete lined to a diameter of 5.5 metres. Plats were developed at No.8 level, No.9level and the loading station.

Jan 1, 1985

By S C. Dominy

A high nugget effect and the presence of coarse gold characterises many vein-gold deposits. The effective sampling of these deposits is often difficult because of the relatively low concentrations involved and erratic nature of the gold. Geological complexity often compounds this effect. Underground development, in-fill drilling and bulk sampling/trial mining are often required to delineate Ore Reserves. Winzing is an historical technique that was used to gather geological and sampling data during underground exploration. It permits access to the mineralised structure below the current datum to help determine viability. Winzing has always been considered an arduous and dangerous task. Modern technology has led to the development of the Mobile Supersucker, essentially a giant vacuum cleaner. This system permits safe and efficient winzing activities, and allows the collection of bulk samples for grade estimation. Bulk samples from horizontal development have long been collected to help define mineable grade. However, when defining blocks below current development, there has been over-reliance on ineffective æsmall sampleÆ drill data. The Mobile Supersucker permits safe and cost-effective development of winzes and off-winze sublevels.

Jan 1, 2003