Search Documents

Assessment of the Consistency Between Different Laboratory Froth Stability Measurements

Sep 13, 2010

Previous methods for the assessment of the explosive potential of gas mixtures have required the plotting of apeexplosibility diagram. These became cumbersome if a large -number of assessments of various sampling locations over a period of time wererequired. This may make the approach of a dangerous situation more difficult to predict. With the aid of a programmable calculator, a new method for the rapid assessment of the explosibility of coal mine sample gases has been developed. This method does not require that an explosibility diagram be drawn to indicate the explosive status of a gas mixture. Simple Cartesian co-ordinates representing the explosive potential of,mixtures are obtained, which may readily be plotted to show changes with time.

Jan 1, 1981

By Meloy TP

Several important, fundamental aspects of the grinding behaviour of mineral systems are addressed. The Levenberg-Marquardt algorithm for systems of constrained non-linear equations was used to solve the steady-state and dynamic population balance model (PBM) grinding equations to obtain the mill matrices and grinding selection and breakage rate functions, respectively. The fact that the PBM model equation Inverse Problem is degenerate or underspecified is demonstrated. Multiple solutions to the same PBM equations are provided. It is shown that there is no unique solution to the Inverse Problem unless additional constraints are provided or assumptions are made such as the Arbiter-Bhrany normalisation assumption. The severity of the non-uniqueness problem for steady state grinding is demonstrated in several examples using typical feed distributions and mill matrices. In addition, it is also demonstrated that when higher than single powers are used in steady-state mill matrix expressions during simulation or calculation (or iterative procedures are used during numerical simulation) and four or more size intervals are used considerable amount of error is propagated throughout any calculation. Each solution to a PBM, while giving the same prediction during a single mill pass, gives different solutions or predictions for mill composition upon subsequent passes. In addition, it is shown that there is a problem with building up a grinding mill knowledge base with PBMs. A similar analysis was done for the dynamic or kinetic PBM equations. The fact that the dynamic PBM Problem is degenerate or underspecified is also demonstrated. Multiple solutions to the same dynamic PBM equations are provided. Again, it is shown that there is no unique solution to the Inverse Problem unless additional constraints are provided or assumptions are made such as the normalisation assumption. Each solution to a dynamic PBM, while giving the same prediction for a given grinding time interval, gives different solutions or predictions for mill composition for other grinding times. Actual experimental grinding data was assessed to determine the functionality of mill selection and breakage functions. The functionalities obtained through constraints were compared with those obtained with the normalisation assumption of Arbiter-Bhrany which relates breakage functions to particle size distribution. The capability of the population balance model to predict grinding behavior over time in various mineral grinding systems was assessed. The required functionality of selection and breakage functions for effective prediction of grinding behavior in mineral systems is discussed.

Jan 1, 1993

By A J. Cornah

Critical decisions in iron ore project evaluation and production are based on global and local spatial estimates of primary mineral deposit properties (such as in situ geochemical grades) and geometallurgical responses (such as screened, washed or concentrated product yields and grades), which are derived from limited sample data. These spatial estimates are typically made using classical geostatistical techniques, which fundamentally assume that the attributes of interest behave additively. This assumption is generally appropriate for æprimaryÆ variables but æresponseÆ variables may behave non-additively and therefore their direct linear estimates may be biased.In this paper an existing additivity testing mechanism is used to quantify the bias resulting from direct linear estimation of a non-additive iron ore attribute. Data from a magnetite project are used to determine the circumstances under which such biases may be of material impact. The implications for iron ore resource estimation, geometallurgical modelling and grade control are outlined and discussed.CITATION:Cornah, A J, 2013. Assessment of the impact of non-additivity in the estimation of iron ore attributes, in Proceedings Iron Ore 2013 , pp 129-136 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By Stewart R

Potential acid rock drainage from the destruction of metalliferous sulph-ides is recognised as a critical factor in the design and economics of any mining venture. While this realisation is relatively new, mining companies have embraced the issue with the aim of scientifically quantifying the magnit-ude of the problem, specific to indiv-idual properties.Coinciding with the development of the open pit mine at Porgera, a comprehensive assessment of the potent-ial for the formation of acid rock drainage was initiated in 1991. Detail-ed study of the mineralogical charact-eristics of all rock types, along with extensive test work to determine the maximum potential of rocks to generate and consume acid (known as acid base accounting or ABA), has been conducted. Correlating this with the known and interpreted geology of the open pit has indicated a strong relationship between rock type, sulphur content and the acid base character. This relationship is used daily as a simple, cost effective means for classification and management of the variety of material types produced from the minincx operation.

Jan 1, 1994

By B Mohanty, D Zwaan

Systematic near-field vibration monitoring of stope blasts was carried out in a large, deep underground mine. A total of 31 production blasts were studied in order to investigate the effectiveness of existing blast designs. This involved the vertical retreat mining method, which requires drilling a raise bore or blasting a slot raise (typically 1.22 m in diameter) using large diameter boreholes (165 mm). The diagnostic technique employed multistation near-field monitoring of blasts with high-g (100 g) and high-frequency (>10 kHz) triaxial accelerometers. The amplitude of the vibrations is correlated with the strain energy transmitted from each explosive deck. The results showed that more than 30 per cent of the explosive decks contributed little energy to the rock breakage process in these blasts, and an equal number contributed only inadequately. These findings are indicative of serious blast malfunctions. The problems can be traced to inadequate deck blast design and possibly to drill hole deviation. The various causes for such malfunctions are discussed and remedial measures suggested.CITATION:Mohanty, B and Zwaan, D, 2015. Assessment of underground production blast designs and blasting performance, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 607–616 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

Mining software systems have provided a basis for integration of resource, survey, and design functions. They can similarly provide a basis for incorporating ground conditions into the process.Exploration and mine geologists have a prime role to play in this process, extending their responsibilities further across the geological spectrum, into exploration of ground conditions, analyses of results, and assessments of their implications for mining. Ground conditions are as much a part of the geology of a prospect or mine as its mineralisation, and can have critical imnlicationa for mining.

Jan 1, 1993

British Coal has always been a big mining company and its management has been beset with many of the problems one would associate with such an undertaking. These include its accountability to Government, its market vulnerability to competing fuels and to imported coal and its relationship with its workforce but also with its own history and size. As a fragmented private industry up to and including the Second World War, it was starved of capital and its management developed an historic relationship with its workforce which was often counter productive to success. Once nationalised, it contributed greatly to post-war industrial regeneration, investment was forthcoming to reconstruct existing mines, sink new ones and to mechanise production operations. British manufacturing companies contributed to this mechanisation drive, the very success of which drove up production and productivity and against a declining market, contributed to the reduction in size of the industry. Production machinery design evolved in the 1960s with close collaboration between manufacturers and users such that an inevitable proliferation of machinery types and specifications developed to meet local needs. Longwall mining internationally outside Western Europe only became significant in the 1970s. It became apparent that international operators demanded higher levels of plant performance from British manufacturers than British Coal did. This was the birth of the "heavy duty" plant concept. As international performances outstripped our own then British Coal moved in to invest in itself, in this heavy duty. This re-investment commenced in the mid 1970s but only gained real momentum in the 1980s when it became a virtual re-equipping exercise for the whole industry.

Jan 1, 1988

By S B. Sheldon

Wall control programs tend to be expensive and consequently require financial justification in order to get approval for the expenditure required. The difficulty faced in getting this approval is that the outcomes of a wall control program are all subjective – a prediction of wall stability and what the wall would do with and without the program. Determining a net benefit is difficult and often justification of a wall control program is based on gut feel, history and a good selling campaign to build a perceived need.This paper outlines a simple solution to this problem by applying risk management principles to wall control. The process is to identify the risks to the operation associated with current wall conditions and then build a risk database for different potential scenarios for each risk. A financial impact is assigned to each risk scenario to complete the database. A consequence and likelihood analysis of each of the risks is undertaken and a formula applied to estimate the projected cost to the operation for the current risk profile. The process is repeated for the predicted wall control conditions after the application of the wall control program. A successful wall control program will reduce an operation’s risk profile so this projected cost should be less than that calculated for the current scenario. The difference in the two projected costs is the value that the wall control program has produced and this value can be used to determine the net financial benefit potential for the wall control program.This methodology can also be applied to other improvement programs that focus on risk reduction such as vibration control.

Nov 8, 2011

The paper reviews the majority of associations and institutions which operate in support of the Australian mineral industry. The review covers historical aspects of each organisation and the current activities and management structure. The linkages between the organisations through membership are briefly discussed. The paper comments on the evolution of the formation of the organi- sations and the networks between them that do exist and operate regu- larly. Rationalisation or a process to consider formation of new groups to fill gaps in the network are recommended for further research.

Jan 1, 1988

Blasting has been the most frequently used method for rock breakage since black powder was first used to fragment rocks, more than two hundred years ago. This paper is an attempt to reassess standard design techniques used in blasting by providing an alternative approach to blast design. The new approach has been termed asymmetric blasting. Based on providing real time rock recognition through the capacity of measurement while drilling (MWD) techniques, asymmetric blasting is an approach to deal with rock properties as they occur in nature, ie randomly and asymmetrically spatially distributed. It is well accepted that performance of basic mining operations, such as excavation and crushing rely on a broken rock mass which has been pre conditioned by the blast. By pre conditioned we mean well fragmented, sufficiently loose and with adequate muckpile profile. These muckpile characteristics affect loading and hauling (Scott, 1996). The influence of blasting does not end there. Under the Mine to Mill paradigm, blasting has a significant leverage on downstream operations such as crushing and milling . There is a body of evidence that blasting affects mineral liberation (Djordjevic, N, 2001). Thus, the importance of blasting has increased from simply fragmenting and loosing the rock mass, to a broader role that encompasses many aspects of mining, which affects the cost of the end product. A new approach is proposed in this paper which facilitates this trend æto treat non-homogeneous media (rock mass) in a non-homogeneous manner (an asymmetrical pattern) in order to achieve an optimal result (in terms of muck-pile size distribution)Æ. It is postulated there are no logical reasons (besides the current lack of means to infer rock mass properties in the blind zones of the bench and onsite precedents) for drilling a regular blast pattern over a rock mass that is inherently heterogeneous. Real and theoretical examples of such a method are presented.

Jan 1, 2001

An asymmetrical floating point Array Processor is a special-purpose Scientific Computer which operates under asymmetrical control of a host Computer. Although an Array Processor can receive fixed point input and produce fixed point output, its primary mode of operation is floating point. The first generation of Array Processors was oriented towards time series information. The next generation of Array Processors has proved much more versatile and their applicability ranges from Petroleum Reservoir simulation to speech synthesis. Array Processors are becoming commonplace in Mining, the primary usage being construct- ion of grids - by usual methods or by Kriging. The Australian Mining community is among the world's leaders in regard to computer-assisted Exploration and Exploitation Systems. Part of this leadership role must be providing guidance to Computer vendors in regard to current and future requirements.

Jan 1, 1983

In mid-1998 Atlas Copco Rock Drills AB introduced the first member of a new family of drill rigs. This new family, Rocket Boomer L1C/L2C/L3C, is based on modern computer technology and also on what is characterised as information technology. The design of the drill rigs are modularised both in hardware as in the software. This means that the functionality of the drill rigs is upgradable step by step. Added upon the basic drill rig functions are the new options as ABC Regular (known also as Contour Control), ABC Total, drillplan generator and communication products. The main objectives of these functions are to facilitate real quality drilling.

Jan 1, 2003

By E N. Isaev, L E. Levin

New data on the geology of the Late Jurassic to Holocene sediments cover of the World and associated mineral resources (oil, gas, ferromanganese nodules, ores of massive sulphides and other metals) have been compilled in the Atlas at scale 1:25,000,000 and 1:10,000,000. The work was performed by scientists from four Institutes of Russia (VNIIzarubezhgeologia, VNIIoceangeologia, Vernadsky Institute of Geochemistry and Analytical Chemistry of theRussian Academy of Sciences and Geological Institute of the Russian Academy of Sciences). The Atlas shows variation of thickness and formational composition of the large complexes (Upper Jurassic-Early Cretaceous, Upper Cretaceous Eocene, Oligocene-Neogene, Pliocene-Pleistocene), distribution of oil/gas and ore deposits in each complex, data of deepsea drilling (leg 1-130),  thermo-pressure condition in the sedimentary basins within Circum-Pacific Rim.

Jan 1, 1995

By Isaev EN, Levin LE

New data on the geology of the Late Jurassic to Holocene sediments cover of the World and associated mineral resources (oil, gas, ferromanganese nodules, ores of massive sulphides and other metals) have been compilled in the Atlas at scale 1:25,000,000 and 1:10,000,000. The work was performed by scientists from four Institutes of Russia (VNllzarubezhgeologia, VNlloceangeologia, Vernadsky Institute of Geochemistry and Analytical Chemistry of the Russian Academy of Sciences and Geological Institute of the Russian Academy of Sciences). The Atlas shows variation of thickness and formational composition of the large complexes (Upper Jurassic-Early Cretaceous, Upper Cretaceous- Eocene, Oligocene-Neogene, Pliocene-Pleistocene), distribution of oil/gas and ore deposits in each complex, data of deep- sea drilling (leg 1-130), thermo-pressure condition in the sedimentary basins within Circum-Pacific Rim.

Jan 1, 1995

By Hirst H, McAfee J

In December, 1934, Mr. R. Sussex extruded some silver lead alloy wires in order to determine their electrical resistance. After the determinations had been made each wire was threaded through a sheet of paper on which the composition was noted. The wires were placed in a more or less tangled mass in a cupboard in March, 1935. It was not until September, 1936, that they were re-examined, and it was found that during the eighteen months some of the wires had corroded very badly. It was not until March, 1938, that the wires and the corrosion product could be examined, and the results are given in the following pages. It is of interest to note that none of the numerous silver-lead alloys which have been used for creep testing in the rolled condition have shown a similarphenomenon. The silver content of the rolled alloys was, however, never greater than 0·1%.GENERAL APPEARANCE OF THE CORRODED WIRESThe wires contained 0·1% up to 28% of silver, and a general examination showed that the corrosion had progressed farther the higher the silver content. This can be seen in Fig. 1, which is a photograph taken in March, 1938, of typical wires at a 'magnification of five diameters. In the early stages the corrosive action seems to be localized and an area of grey, yellow or reddish brown powder appears. The grey corrosion product is by far the one, most frequently seen, and in the later stages the only one visible from the outside. The reddish coloured product is sometimes seen on the residual metallic centre when the grey product has been broken away.The irregular extent of the corrosion can be seen in Fig. 2, which shows (natural size) the 5% silver wire after standing two years. The corroded parts are seen to be much thicker than the slightly corroded ones. The corrosion product, being non-metallic, is quite brittle and falls away from the wire on bending. In the extreme case the' whole wire has corroded and presents a cracked appearance as seen in Fig. 1 (281% silver).An approximate idea of the extent of corrosion can be obtained by measuring the diameter of the corroded part. The original diameter in each case was ·050/ ·051 inches and in Table I are given the diameters of the corroded parts after Hand 3 years respectively. When the diameter...

Jan 1, 1941

Resonance re-emission from nickel vapour affords a convenient method for isolating the resonance lines at 3415A, 3515A, and 3524A. The vapour is generated by cathodic sputtering and is illuminated by light from a nickel atomic spectral lamp. The resonance lines thus isolated can be usefully employed for absorption measurements on mineral samples where the nickel concentration is too high for measurements with the more sensitive line at 2320A. A spectrophotometer employing a resonance lamp as monochromator possesses several advantages where a great number of determinations are made under routine conditions. The wavelength setting is stable under even the most rigorous conditions and with the provision for automatic setting of full scale deflection the instrument requires virtually no adjustment. The instrument has been used under routine conditions for the determination of nickel (in the range O· 05-2 per cent) in mineral samples.

Jan 1, 1968

By B M. Moudgil

Atomic force microscopy (AFM) has become an important tool for understanding the nano- to molecular scale mechanisms predominant in multiphase systems. In flotation research, the use of AFM holds promise for unlocking and establishing fundamental mechanisms, ultimately leading to significant advances in process performance. From measuring and characterising surface forces, the structure of molecules at interfaces, and nanoscale features on flotation media, AFM is a powerful tool that has only begun to impact flotation research. Highlights of advances made in the utilisation of AFM for flotation research at the University of Florida are given with an emphasis on interpreting the mechanisms behind calcium activation in phosphate flotation and the impact of nanoscale asperities on collector-born surface hydrophobicity.

Jan 1, 2005

In essence, these statements concur, However, management predominantly controls the organisation's communication environment (5), Consequently, the participation by employees in safety is greatly influenced by the quality of upward communication, (See section on authority for discussion on two way communica-ò tionò) Emotional survival contributes to the communications and it is said to occur as follows: -- We. aU tend to move towaAA 6.itw tLon,s which aid the achievement oj5 owc goa o and way {y/wm ones which testh ict achievement." Consequently, although the work force are prepared to contribute, they will not make the effort for long if management does not respond in deed. The Robers report includes the following statement; "Satiety and heat h at wank is a matte o6 e66ic,ient management. But it .L not a management pn.enogative. Wank people muht be encouAagad to pattiaipate úu.Uy in the making and movutoni:ng ob a/vua.ngements ban .6aJety and heath, at their. pace ofj wonk.t'(3) Attitudes dominate within this region. Emotional surviv- al is paramount. Management is the catalyst. They dominate the communication channels. Participation does not exist without two way communications and positive responses by those involved, Fault Doctrine. Eliminate faulty human behaviour. This concept lives with us as the predominant prior- ity of many safety programs. The concept is a drain on limited resources., Remember, malaria. At one stage this disease was believed to be caused by the mat or bad air emanating from persons whose profaneness or impious behaviour incurred such reprisal. Today, such a concept of malaria seems so ridiculous, (9)

Jan 1, 1979

Jan 1, 2004