Search Documents

Recovery of Vanadium from Stone Coal Through an Environmentally Friendly Acid Leaching Technology

Sep 13, 2010

A novel approach to validate size distributions obtained from bubble sizing techniques is introduced. The experimental rationale consists in verifying whether the output features the anticipated bi-modality when two uni-modal populations (ca. 0.5 and 5 mm) are mixed in a bubble column. The degree of deviation is quantified by comparing the calculated and real proportions on a volumetric basis. A sampling-followed-by-imaging technique was used to proof the concept. The results showed the anticipated bi-modality in which the real and calculated proportions corresponded with a deviation of less than 15 per cent, considered good given the severity of the test. However, the deviation was correlated to the superficial gas velocity (Jg) in the column and was consistently against smaller bubbles. Possible sources of bias are suggested.

Jan 1, 2005

Early efforts to control the dust necessarily produced during dry crushing operations, took the form of venturis at loading chutes and other places where dust was most evident. These venturis discharged to the atmosphere and for obvious reasons were not very satisfactory.Attempts to collect the dust drawn off by the venturis, using dry cyclones, were not successful, the cyclones catching only the coarser particles. Further, no satisfactory method of continuously discharging the dust catchment was evolved. Water sprays were also used, and will be referred to later.In 1940, a single discharge fan of 3,000-4,000 cu. ft. per minute capacity, was installed to draw the dust-laden air from the Symons crushers and ·screening sections with their attendant conveyors. Suction was through two 15 in. ducts which branched off into 10 off-takes situated over the conveyers at points of discharge from crushers and screens.A dry cyclone was installed in front of the fan, which exhausted into a bag-house.The cyclone suffered from the defects of the smaller units mentioned earlier. When the collected dust reached a certain level in the cone, no more collection would take place until the cone was emptied. This objectionable feature was overcome by introducing a jet of water ahead of the cyclone. The water and dust collected overflowed a weir and were pumped to the mill.

Jan 1, 1948

The Wamum and Idzan Creeks Prospect, located 79km W of Lae, Morobe Province, Papua New Guinea (PNG) was discovered by the exploration arm of Conzinc Riotinto of Australia Pty Ltd (CRAE). The detailed surface exploration and 11 vertical holes drilled by CRAE, combined with the recent work by Highlands Gold Limited, indicate the occurrence of porphyry copper-gold mineral- isation and associated alteration. The prospect occurs within andesitic volcanics of the Middle Miocene Langimar Beds. It is bounded by NE trending faults to the NW and SE. The alteration and mineral- isation is hosted in the andesitic tuffs adjacent to high level quartz diorite and hornblende diorite stocks. A NW trend to alteration and mineralisation is obvious in Wamum and Idzan Creeks. The main alteration type is propylitic with minor zones of potassic alteration. A late sericite-quartz-kaolinite-pyrite alteration overprinted the earlier alteration and mineralisation. Copper and gold mineralisation is related to a quartz-carbonate-chalcopyr-ite-pyrite (¦ bornite) vein stockwork and biotite ¦ K-feldspar alteration. The mineralisation system at Wamum and Idzan creeks is low in total sulphides. It is considered as a high- level fracture-controlled system with limited low grade Cu-Au mineralisation.

Jan 1, 1991

By L Torckler, J Hobbins

Favona is a blind low-sulfidation epithermal vein deposit in the Waihi Vein System approximately two kilometres east of the world class Martha Hill deposit that has produced nearly 6.8 M oz Au to date. The Favona epithermal system has surface expression in variously altered and mineralised hydrothermal eruption breccias forming a series of low hills that are windows through post mineral dacites and ignimbrites. The tip line of the Favona vein is about 50 û 100 m below surface with a steeply east dipping principal vein structure carrying numerous hanging wall splays in the upper flatter section and thickening down dip where the vein steepens. Host rocks comprise feldspar phyric andesite flows with minor pyroclastics. Although Favona has a strike length in excess of 1000 m and vein widths up to 25 m over a vertical range in excess of 400 m it was only recently discovered after nearly thirty years of exploration by various companies involved in the Martha Hill joint venture that operates the Martha Mine. Since discovery in 2001 a feasibility study based on 27.5 km of diamond drilling in 83 holes has been completed reporting a reserve of 1 Mt @ 10 g/t Au against a resource of 1.8 Mt @ 10.3 g/t Au. Exploration is continuing with a further 20.5km of diamond drilling completed to date on nearby prospects.

Jan 1, 2004

Future depth and production limitations of an ore hoisting system are fixed by its initial design criteria. There is little scope to extend these limitations once installation is completed. Depth and production rate upgrades from the initial duty to the hoistÆs practical limitations require capital expenditure in stages, each of which can be defined when assessing the initial system design criteria. A means of presenting and assessing the design criteria, the limiting factors in each option and the relative present and future capital costs is necessary to arrive at a solution that delivers the best value to the mine. Application of this technique to recent friction winder installations and upgrades in the Australian mining industry is of particular interest; however, the analysis methods are also applicable to drum hoists. It is usual to specify a minimum hoisting capacity and depth, based on mine ore handling design and production needs. The final hoist depth and production rate are usually a result of the initial hoist design and hence it is useful from the outset to specify a required production versus depth envelope for the mine. Technical solutions can then be modelled within this envelope at their initial and final duties and a comparative analysis made against the cost of installing and progressively upgrading each solution. Understanding the factors that constrain each solution to a maximum production rate at a given depth is important, as the costs of overcoming limiting parameters such as rope tread pressure and motor power can be significant. The task of understanding and evaluating the options open to the hoisting system designer is simplified using this approach. Communicating the results of a multi-dimensional problem such as hoist specification is also made easier using the graphical methods inherent in the analysis.

Jan 1, 2005

A brief review of currently available "commercial" information on methods of treating ilmenite s to produce high titanium content "upgrades" is made. In this back- ground the CSIRO/Murphyores Process is described and its relationship to other methods Discussed.

Jan 1, 1972

By Y A. Stepanyants, J Crawford

A practical field method for determining the maximum value of the intrinsic oxidation rate, Smax , of sulfidic materials in waste rock dumps is proposed. Knowledge of the intrinsic oxidation rate of sulfidic materials distributed in a dump is necessary for predictive modelling of oxidation and pollutant generation over time. The suggested method uses the fact that drilling waste rock dumps to install probes for monitoring temperature and oxygen concentration causes large volumes of air to be injected into a dump by the drill rig. By measuring the rate of decrease of oxygen concentration along the length of a borehole immediately after installation, it is proposed that Smax can be calculated at different depths. The aims of this work were: to derive a simple, practical formula for the estimation of Smax from the oxygen concentrations measured over time, based on some simplifying assumptions; to use a two-dimensional numerical model that incorporates all the necessary physical processes to model the behaviour of an aerated dump over time for a reasonable range of dump and material parameters; and to compare the results of the two approaches to assess the validity of the simple formula as a method for estimating Smax. It has been found that the technique can provide reliable estimates of Smax when the value is of the order of 10-7 kg(O2) m-3 s-1 or greater. At the lower end of the range however the radius of the zone aerated during drilling becomes an important parameter and further work has been recommended to investigate this aspect of the method.

Jan 1, 2003

Segregation studies in ternary systems of glass ballotini, iron ore and coke particles (with size range of 1-8 mm in each) in filling and emptying a laboratory size Paul Wurth hopper are described. In-bin segregation is shown to be a function of the position in the hopper, the nature of the material and the feed composition. The in-bin results are correlated by the equation C = C0k, where C and C0 are the size compositions (wt per cent) in the hopper and feed respectively, and k is an experimentally obtained segregation constant. The results of now pallern measurements show that material discharges from the hopper according to the sequence; core now - wall now - scaffold now, where the latter represents stagnant material at the hopper wall that discharges last. Size segregation in the discharge stream from the hopper is shown to be a function of in-bin segregation and hopper now pallern. A method of predicting discharge segregation from these two sets of data is suggested. The results of the model studies are also compared with industrial data and these show satisfactory agreement. Discussion of the hitherto ignored effect of size segregation on hopper now rates, stoppages and other operating problems is also included.

Jan 1, 1985

By R Vleggaar

In addressing a short-term operational need for the relocation of a tailings storage facility reclaim pond, a mine has achieved a host of water management objectives. Through effective planning and adoption of a strategic æwhole of mine lifeÆ approach, the mine has achieved significant environmental, social and economic benefits. A review of all water management aspects across the site identified a host of other interrelated water issues and concerns which, if dealt with individually, would prove too costly for individual operational departments. When considered as a whole, however, the issues became opportunities and provided the stimulus for integration of the site water management system. The development of site water and solute balance models provided the tool by which a number of water management options/strategies could be evaluated. The conceptual design and costing of the proposed water infrastructure further facilitated the evaluation of the multiple benefits to be gained from each option. A business case could then be made to mine management for the preferred option. The recommended water management strategy finally recommended to the mine not only provided a tailings storage facility (TSF) reclaim pond, but also provided for:increased wastewater recovery from the TSF, the capture of all waste rock dump run-off, additional water harvesting from local creeks, increased wastewater reuse, improved environmental water management, infrastructure that could be used by the local community after mine closure, and overall cost savings. This paper illustrates how effective water management planning can provide both short-term economic and environmental benefits, as well as long-term social benefits.

Jan 1, 2006

ALTHOUGH discovered as long ago as 1817, by Strohmeyer, the use of cadmium did not become in anyway general for nearly a century. Its properties, although well known, did not recommend it to users of metals generally, and it was, on the whole, regarded more in the light of a nuisance to zinc producers than anything else. Its real value was not appreciated until both the United States of America and Germany, who are entirely dependent on outside sources for their supplies of tin, were faced with the unpleasant fact that their tin stocks were being rapidly depleted, with practically no prospect of having them replenished. This resulted in serious efforts being made in the UnIted States of America to conserve what tin was available, and, as a consequence, several metals were tried in the hope that they would prove satisfactory substitutes for tin. Among these was cadmium, and it was found that cadmium could replace tin in a manner sufficiently satisfactory to permit of its use in many directions where tin had been used before.It is on this ability of cadmium to replace tin that its use became in any way general at first; but since then new avenues of development have been opened up in which its physical and chemical properties are proving their value. It is highly probable that its use will extend very considerably as time goes on. OCCURRENCE OF CADMIUM.There are several cadmium minerals known, but none of them occur in profitable quantities as ores. The cadmium of commerce is derived almost entirely from zinc minerals and ores in which it is almost invariably present in proportions which are usually very small. Cadmium behaves metallurgically almost the same as zinc, and hence constitutes a fraction of 1% of almost all spelter.

Jan 1, 1923

By M Kent, D Elder, J Woodward, R Edwards, B Catto

At Tropicana gold mine (TGM), mine planning is completed from ‘one source of truth’ known as the Integrated Planning Model (IPM). The IPM is a block model which forms a core component of the TGM Mine Planning System – used for short, medium and long-term mine planning cycles, and for Mine to Mill reconciliation.The IPM was developed from a desire to consolidate long-term information contained in mineral resource and ore reserve models, with short-term information from the grade control processes, including grade control models and ore polygons.The IPM is informed initially by resource models, upon which the longer term budget and schedules are based. The IPM is routinely updated with grade control models and ore design information, providing increased confidence for short to medium term mine planning. In this format, the IPM also provides a framework for reconciliation of resource performance with grade control, mining actuals and mining schedules, and ultimately milling. As well as a means for analysing past performance through reconciliation, it has proven its worth as a predictor of variation and an input to successful schedule sequencing and change management. The IPM is a critical component of the TGM Mine Planning System, providing a centralised framework for short interval mill feed prediction through to life-of-mine (LOM) planning.Current development of the IPM is working towards incorporating Mine to Mill optimisation and real-time material tracking projects at TGM. If successful, the model will provide a truly powerful mine planning data source. Current development outlines a mechanism for tracking material from Mine to Mill, and for transferring mill performance data back to the IPM. Increasingly advanced material classification and mine planning, incorporating the multiple geometallurgical variables, will enable the mine to provide consistent mill feed products and result in a steady state and optimised mill.This paper outlines the vision, creation and benefits of the IPM at TGM. It also introduces the ongoing developments to ensure the IPM becomes only more relevant to successful and integrated mine planning as TGM matures from the new kid on the block to the old hand in the neighbourhood.CITATION:Catto, B, Elder, D, Edwards, R, Kent, M and Woodward, J, 2017. An integrated approach to mine planning – building the integrated planning model at Tropicana gold mine, in Proceedings Tenth International Mining Geology Conference 2017, pp 305–314 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By A Ruotsalainen

Mining industry sees a comprehensive future in optimisation and process control. High resource utilisation is a starting platform when lower operational costs with higher rate of return are the target. Simulation is quickly penetrating the mining industry as a planning tool. A discrete event simulation helps to visualise the reality of a mine and the various mining processes, which typically include a fair degree of complexity. What-if scenarios can help to determine the impact of occurring changes to production. Understanding of critical points in the layout and resource allocation at an early stage can help to optimise the material flow. The obtained information may then be used as proposal or confirmation of the system applicability and economy. Simulation is a way to fine-tune and optimise the resources within. It helps to predict system sensitivity to various aspects. Although simulation today is used typically in a feasibility stage, there is an opportunity to continue using simulation for further process enhancement. In the future simulation will without doubt be used increasingly as a dynamic simulation and continuous improvement tool. This paper discusses the use of OptimineÖ simulation tool in resource optimisation. Some examples describe the way the tool operates and how it helps to view the technology, mine layout and operational data.

Jan 1, 2003

The unique chemical and physical properties that can be displayed by polypropylene and its copolymer derivatives are enabling its development as a truly versatile material for water filtration. Well known applications include spiral wound cartridge filters commonly used for household water or the office drinking fountain, to pressure membranes that provide micro, ultra or nano size filtration barriers, whilst needle-felt or woven cloth filter belts or inline pressure bag cloths are well known to the hydro metallurgist and process engineer. A relatively new filtration concept that is generating interest and applications across all industries including the mining sector involves use of a unique fabric type filtering media made from polypropylene fibres. This technology not only has a vastly wider window for potential applications, it delivers an attractive cost saving alternative to the traditional sand media or diatomaceous earth type filters, along with potential benefits for integrated filtration units. This paper discusses the proven potential of the fabric media technology with examples of performance comparisons and confidence gained from full scale operating installations at mine sites and other locations.

Jan 1, 2004

The reasons for and the methods of inte- gration of the gold treatment plant with the existing nickel concentrator are discussed. The integration was accomplished in three stages commencing in May 1980 and attain- ing current throughput in December 1982. The problems encountered and their solution, including the design and construction of a new tailings dam are also discussed.

Jan 1, 1984

By Mallett C

Coal mines are dynamic systems that change continually in size, shape, and condition. Large quantities of data about production, coal quality, ground stability, ventilation monitoring, equipment performance and location, vehicle and personnel movements and geology, are generated from all parts of the mine.Internet technology and virtual reality technology are now being combined to provide an intuitive, multi-dimensional information system which can simultaneously display any information that can be collected and stored by a computer. Physical information is directly displayed as 3-dimensional objects in the mine model. Numerical and text information is dynamically linked to these objects and accessed by "clicking" on them.

Jan 1, 1998

In June 1992, the High Court of Australia recognised native title of the Meriam people over parts of the Mer Island in the Torres Strait as a form of common law. The Court also indicated that native title may have survived European settlement of the mainland Australia where it had not been extinguished by Governments and Aboriginal people have maintained their traditional connection with the land. The decision meant that two systems of land law were seen as existing side by side in Australia: ò one which derived from grants from the Crown under laws passed by Parliament; ò another which derived from the diverse laws and customs of the many Aboriginal groups in Australia.

Jan 1, 1996

By S Munn

Today, it can be said that the majority of mines utilise communications equipment in one form or another. Either for communications between staff making their day-to-day operations more efficient, or for emergency communications, as well as linking computer based mine management systems, and providing remote control over complex mobile and fixed machinery. With the advances in technology now available, we are moving into the next generation of mine communications equipment, using digital communications in the underground mine environment. It is a proven fact that an efficient underground mine communications system can help maximise production, by providing major gains in areas such as equipment and manpower utilisation, staff and vehicle tracking, reaction times to break downs and emergencies. In this paper we will describe some of the facilities that are currently available, as well as what will soon be available to mining and tunnelling companies around the world.

Jan 1, 1999

Accurate geometric models of orebodies establish the framework for reliable mineral resource estimates that provide a basis for further exploration and mine planning, as well as for financial models that ultimately determine the economic viability of a deposit. Traditional, explicit geometric modelling techniques that are utilised for resource modelling by the general mining software packages, such as MineSight«, involve manually digitising interpreted ore outlines that must be carefully linked to create valid geometric solid models. An alternative, implicit modelling method, employed by LeapfrogTM software relies on a fast method of global interpolation, which offers several advantages over traditional modelling techniques. Although previous case studies have documented the relative efficiencies of the two approaches, the accuracy of the two methods has not been previously quantified and compared. This study quantifies the accuracy of solid models created using explicit and implicit methods, and compares the differences between the models. Solid models of the Doris Hinge vein gold deposit (located in the Hope Bay district, Nunavut, Canada) are constructed from preliminary and follow-up drilling data using both modelling techniques. The accuracies of the solid models generated using preliminary drilling data are determined by measuring the 3D distance between the surface of the models and the actual contact location defined by the follow-up drilling data. Additional comparisons based on volume, cross-sectional area and surface differences were made between both phase 1 solid models and solid models constructed from phase 2 drilling information. The overall results of this study find that the MineSight« and LeapfrogTM solid model accuracies are virtually the same, and that their volume, cross-sectional area, and surface differences are comparable. This study concludes that the implicit modelling technique generates accurate solid models that can be used in place of explicit models as ore shells for resource estimation in certain circumstances.

Jan 1, 2006

Experimental petrology may be used to accurately constrain PTX conditions in order to calibrate and understand geologic processes. This method may be used to answer postulated questions, by recreating known geologic conditions and observing changes in the experimental charges. The purpose of this project was to determine the eutectic composition and temperature in the ternary system PbS-FeS-ZnS ¦ (Ag2S), at ambient and elevated pressures and elucidate if the sulfides of the Broken Hill orebody may have been partially molten during highgrade (granulite facies) metamorphism. The study determined the eutectic temperature and composition in the system PbS-FeS-ZnS to be 800¦2¦C and 62.5% PbS, 30.5%FeS, 7% ZnS respectively, at one atmosphere, and the eutectic temperature at 27 kbars was found to be 960¦C¦10¦C, with a eutectic composition enriched in ZnS relative to the one atmosphere eutectic. the addition of lwt.% Ag2S to the system depresses the eutectic temperature to 772¦2¦C at 1 atmosphere and below 810¦5¦C at 5 kbars. The conditions of peak metamotphism for the cental and southern areas of the Broken Hill Block, New South Wales, Australia , lie above the solidus of the PbS-FeS-ZnS-Ag2S system, strongly suggesting that partial melting occurred in the orebody.

Jan 1, 1998