Search Documents

By S. Esfahani, M. Barati

Heat recovery from blast furnace slags is often contradicted by another requirement, to generate amorphous slag for its use in cement production. As both the rate and extent of heat recovery and slag structure are determined by its cooling rate, a relation between the crystallization kinetics and the cooling conditions is highly desired. In this study, slags with different basicities were studied during non-isothermal cooling. Their continuous cooling transformation (CCT) diagram were plotted and compared with each other. Then, a mathematical model was developed that predicts the amount of crystallization during cooling. The results were validated by experiments performed by Single Hot Thermocouple Technique and image analysis. A second mathematical model that calculates temperature history of slag during its cooling was coupled with the above model, to allow optimizing the slag/air ratio for both heat recovery and slag glass content.

Jan 1, 2015

By Amin Jafari

Macrosegregation has always been an important issue with the solidification processes, particularly in Direct-Chill Casting of Aluminum alloys, where uneven properties, surface and bulk defects and limitations in productivity can be arisen due to macrosegregation in the cast product. Following the global attempts to practically predict the macrosegregation, in the present work, a numerical model was developed based on an industrial scale DC casting process to simulate the solidification and macrosegregation in an Al-4.5%Cu billet. Interesting aspects of this investigation are concerned with an efficient numerical scheme to keep simplicity, consistency and desired physical resolution of the solidification phenomena together. In the mathematical model, coupled conservation equations of mass, momentum, energy and species were solved numerically using finite volume method. A different numerical scheme, called SIMTLE, was introduced to link the energy and species equations with the phase diagram of the alloy. Calculations were performed on an industrial case and obtained results were compared to available experimental data to assure the performance of the model. Different macrosegregation features were predicted and discussed on the solidifying Al-alloy billet.

Oct 1, 2011

By M. Cala

Underground coal gasification is technology which enables energy to be extracted from coal beds where mining by means of classical methods is either impossible or uneconomical. The process of coal gasification itself is a complex phenomenon which includes chemical and physical processes: thermal, hydrological and mechanical. Additionally, the analysis of underground coal gasification is difficult to carry out for environment reasons, this being due to the local characteristics of the areas where it is carried out. This paper deals with interaction of geo-reactor with surrounding rock mass, it omits the chemical processes inside geo-reactor itself. Due to the complexity of the processes proceeding and during underground coal gasification coupled with minimal practical experience in using this technology, it is difficult to estimate its influence on the surrounding rock mass. Within this scope, the use of numerical programs can be useful. This paper presents a trial of modeling the processes accompanying underground coal gasification. The processes proceeding and during the underground coal gasification are characterized, and the significant, specific phenomena are discussed, with respect to the influence on the surrounding rock mass. For the chosen processes, examples of numerical calculations are presented. These enabled conclusions to be drawn and also provided directions for the modeling of the underground coal gasification processes.

Aug 1, 2013

By Michael Klichowicz, Holger Lieberwirth

"For a detailed prognosis of mineral comminution processes, simulation tools like DEM still pose various challenges. Less realistic mineral structures can affect the results of simulation models such as bonded-particle models (BPM). Hence, in order to design mineral processes with these models as tools, representative mineral input data should be used. The article shows, how realistic 2D-structures can be modelled by taking advantage of the parameters identified by the Quantitative Mineralogical Analysis (QMA). Important quantitative parameters can be derived by analyzing three orthogonal thin or polished sections. For this reason point, line, and area analysis are applied. The mentioned parameters precisely describe the texture and structure of minerals. The newly developed software is able for the first time to semi-automatically analyze images of mineral structures using QMA. Moreover, statistically equivalent structures of minerals can be modelled using the QMA- parameters. Generating synthetic, but equivalent mineral structures opens the door for more reliable BPM based simulations. Within future research, the procedure will be adopted to generate 3D-structures. Therefore, QMA-based routines that already have been applied to generate 2D-models shall be utilized as basis. The aim of this procedure is to synthesize realistic microstructures based on certain statistical figures in order to improve comminution simulations.INTRODUCTION Due to its increasing capability, the use of computer technology is permanently intensifying in the design of mineral processes. The recent past has impressively shown that computer models can enhance the understanding of mineral processing. There is in fact a rising number of research activities, which are using simulation approaches to study various aspects of it. Weerasekara et al. (2013) give a comprehensive overview over the application of discrete element modelling (DEM) in the science of comminution.Nonetheless, using simulation tools such as DEM in general still poses a challenge. For a detailed simulation of a mineral comminution process with DEM, bonded particle models (BPM) appeared suitable in the past. The following issues, however, affect an appropriate prediction when modelling with BPM:• Simulations with high numbers of particles may need a lot of time for computation. • Internal modeling parameters like the spring and damper constants in DEM have to be adjusted by comparing its specific crushing behavior in the simulation to reality.• In order to use DEM for prediction of mineral processing, it is essential to validate the correctness of the models and assumptions, which is sometimes difficult. As Weerasekara et al. (2013) have stated it is crucial that the DEM method as well as the DEM code work properly.• It is challenging to implement the complex geometric structures of real minerals into the model."

Jan 1, 2016

By S. A. Briggs

Bioremediation has been accepted as a treatment technique for groundwater contamination in subsurface soils and shows promise for contaminated fractured rock environments. Biological growth in fractured rock is expected to occur predominantly as biofilms attach to the fracture surfaces. Biofilms in rock fractures are subject to a complex system of forces and other phenomenon due to the dynamics of the bulk fluid in which they grow. In this paper, through the applications of computational fluid dynamics (CFD) to rock fractures, where the boundaries are rough and the flow is complex, a precise analysis was conducted of the interaction of a fluid flow and the rock fracture. Specifically, hydraulic parameters and velocity profiles of an actual rock fracture were calculated and compared to a fracture of equivalent aperture. From the analysis it is clear that it is important to use more complex models such as the Lattice Boltzmann Method used is this paper to describe fracture flow.

May 1, 2009

By M. R. Hudec, M. A. Nikolinakou, P. B. Flemings

"We model the shale response to the large deformations associated with salt bodies, and we identify the implications of the stress changes for hydrocarbon exploration. We employ both the static and evolutionary approach, and show that while the static one can model actual geologic geometries, only the evolutionary approach can provide a detailed description of the stress history of shales, which is essential for predicting stress, porosity, and pore pressure and, more generally, for understanding Earth processes related to salt-hydrocarbon systems.INTRODUCTIONDuring the last two decades, understanding the stress, material behavior, and pore pressure in shales around salt bodies has become increasingly important. The energy industry routinely drills near salt (Beltrão, Sombra, Lage, Fagundes Netto, & Henriques, 2009; Meyer, Zarra, Rains, Meltz, & Hall, 2005; Seymour, Rae, Peden, & Ormston, 1993), because a significant number of hydrocarbon reservoirs around the world are found in layers dipping away from salt diapirs.Salt is a viscous material that cannot sustain deviatoric stresses. Under differential loading it flows, changes shape, and eventually relaxes to an isostatic stress state (Urai & Spiers, 2007). Therefore, emplacement of a salt body and its viscous relaxation process may cause significant deformation of the surrounding sediments, perturb their state of stress and create local overpressures (Dusseault, Maury, Sanfilippo, & Santarelli, 2004; Seymour et al., 1993). As a result, drilling near salt is particularly challenging, and problems leading to additional expense or even abandonment are common (Bradley, 1978; Dusseault et al., 2004; Meyer et al., 2005; Seymour et al., 1993; Willson et al., 2003).Historically, salt and the evolution of its cross section to the present day geometry have been studied using kinematic restorations (Rowan & Ratliff, 2012). This approach aims to explain the present geologic section through a sequence of plausible past sections; however, it does not model the constitutive response of the wall rocks, hence it cannot provide any prediction on their state of stress. Similarly, largestrain numerical studies (Albertz & Beaumont, 2010; Chemia, Schmeling, & Koyi, 2009; Goteti, Ings, & Beaumont, 2012; Gradmann, Beaumont, & Albertz, 2009) have focused on the rheological evolution of salt systems without modeling the geomechanical response of the sediments."

Jan 1, 2015

By G. C. Weatherly, D. S. Wilkinson, A. M. Limarga

Competition between stress generation and relaxation mechanisms during the oxidation process has been observed. However, the nature of the intrinsic growth stress in thermally grown scales is not well understood. In this talk, we will propose a conceptual model to calculate the intrinsic growth stress based on the analysis of stress-driven diffusional process of oxygen ions along the oxide grain boundary. The calculated stress, which is considered to originate from the constrained lateral expansion of the oxide, is in agreement with a range of experimental observations.

Jan 1, 2004

By Makhlouf Boubahziz

The HNIA field is part of the Tinrhert project which consists of developing 17 fields containing essentially gas with a few small rings of oil. It is considered as one of the main fields in this project in terms of its area and the number of geological structures that has formed it. It is a wide anticline of Cambro-Ordovician age, orientated NNE-SSW and located in the South-eastern part of Illizi basin. This structure extends from Alrar-center in the North, to the North of In Amenas in the South. The area is 1350 km2. The main reservoirs forming HNIA field are the Devonian (F2, F3 and F4), Siluro-Devonian (F6) and Cambro-Ordovician. These latest are formed by 4 sandy units alternated by layers of shale and shaly silt termed from the base to the top as follow: Unit II, Unit III-3U, Unit IV-2L and Unit IV3; these units are the subject of this study. The HNIA field is essentially gas, up to day this field is at the stage of appraisal and evaluation in order to establish a development plan; therefore the main target of this study is to contribute to this frame work. The following objectives are: ?To build a structural model of the study area. ?To integrate all the sedimentological, structural and petrophysical data in order to build a 3D geological model

Aug 1, 2013

By M. Kucharski

The model of the Outokumpu direct-to-copper process deals with a steady-state process the parameters of which do not depend on time. To give a prediction for the process outcome, "a modified black box" method, which ignores most of the chemical reactions in the furnace, was used. This method takes input and output parameters into consideration. The presented model describes the Outokumpu direct-to blister process in the form of the set of linear equations which give mass and enthalpy balances as well as the distribution of elements between blister copper and slag. However, only major substances where quantities in the feed charge exceed a certain level (for example 0.5 kg/ lMg of smelted concentrate) are taken into consideration. Minor elements are distributed among slag and metal phases in a different way. Some of the equations are derived from distribution coefficients. The value of distribution coefficients can be calculated from plant production data.

Jan 1, 2007

By S. A. Vazhnov, A. G. Kalimov, A. A. Potienko

In this paper we describe a mathematical model of the magnetic field and magnetohydrodynamic processes simulation in aluminum reduction cells developed in St. Petersburg State Polytechnic University, Russia. The model includes: (a) calculation of the currents in the busbar system and inside the aluminum cell construction elements including cathode and anode structures, aluminum and electrolyte layers; (b) magnetic field simulation using the integral equation method; ( c) investigation of the magnetohydrodynamic characteristics on the basis of a shallow-water approach. The developed model was used to investigate operational characteristics of the different industrial aluminum cells. Calculated magnetic field distributions and MHD stability parameters were compared with the available experimental information; the comparison demonstrated a reasonably good agreement.

Jan 1, 2006

By Amir Asadi

Various damage modes that evolve with time in polymer composite laminates, such as transverse cracking, vertical cracking, delamination, and fiber fracture, as well as the interaction among them, influence the time-dependent degradation in modulus (creep) and strength (creep rupture) of polymer composite laminates. This study is focused on modeling the time-dependent evolution of transverse cracking in [90] plies of a multidirectional polymer composite laminate [0m/190n]. This model uses a two-dimensional variational analysis to determine the stress state at any given creep time. The elastic stored energy, determined using this stress state, is compared with a critical energy for fracture to determine the crack evolution with creep time. Model predictions are compared with experimental results to validate the model.

Jan 1, 2010

By N. Shi, T. G. Joseph

ABSTRACT Before any large plant is moved onto an oil sands dominated surface, particularly those surfaces encountered in-pit, it is imperative that the ground be evaluated for bearing capacity. A 2230 tonne mobile in-pit hopper/crusher facility designed for operation in the Canadian oil sands was modeled. This evaluation focused on track and outrigger pad versus ground interactions as the key performance indicators of appropriate ground performance below the unit in both operating and repositioning propel modes. A study of cyclic oil sand behaviour was also inferred from laboratory cyclic plate load data as an extension of the simulation model indications.

Jan 1, 2013

By Shoma Sinha, Nirmal K. Sinha

Deformation in a material at any temperature is known to consist of two major components - a reversible (elastic) part and an irreversible part (often called plastic). What is not universally known is the fact that at high temperatures greater than about 0.4Tm, where Tm, is the melting point in Kelvin, the reversible part includes not only elastic but also a delayed elastic (recoverable but time dependent) component. A very simple computational model is presented here for a constant-strain stress relaxation test (SRT) on the basis of a three-component constant-stress rheological equation derived from strain relaxation and recovery test (SRRT) data. It is shown that the rapid stress reduction during the early periods of relaxation when the stresses are high is governed primarily by delayed elasticity irrespective of the imposed strain level. This is in contradiction to the popular concept prevailing today. The asymptotic approach to a quasi-stable stress rate at longer times and lower stresses is, however, controlled by viscous flow (power-law creep). The validity of the theory is examined by comparing the predictions with experimental results obtained for a titanium-base alloy Ti-6246 at 0.45Tm.

Jan 1, 2004

By Sadough vanini Ali

Charpy impact energy of functionally graded steels produced by electroslag remelting in crack divider configuration has been modeled in various strain rates. It has been well known that majority of materials indicate different behaviors under different strain rates and temperatures. Therefore, modifying the elastic-plastic model considering the effects of strain rates and temperature gives us an acceptable prediction of these composites behaviors in impact test. In this investigation, graded steel was divided in to several layers in which the layers have the same strains under the impact. Constitutive equation describing the flow stress variations as a function of strain rates and temperatures, have been used to express the stressstrain behavior of layers. The parameter values of constitutive equation determined for all the layers via using the boundary conditions based on composite graded behaviors which were the characterized ferrite, austenite, bainite and martensitte phases. Consequently by applying the rule of phase mixtures and ascribing the impact energy of each layer to the area of stress-strain curve of the same layer, the whole impact energy of composite is the sum of layers impact energy with considering the layers volume fraction.

Oct 1, 2011

By M. Abdollahi, M. R. Khalesi, Y. Kianinia, A. Khodadadi Darban

High cyanide consumption during the processing of gold ores with high sulphide minerals can make the typical cyanidation uneconomic. Also cyanide is a toxic material and environmental concerns of cyanide compounds are serious. Optimization of cyanide consumption requires a methodology to estimate the amount of exposed cyanicides, the kinetic of their dissolution and estimation of formation of cyanide complexes which consume the free cyanide. In this paper, a methodology to estimate cyanide consumption by modeling the minerals and gold leaching kinetic based on a liberation model and speciation of all possible cyanide related species in the solution is presented. The results showed that this methodology could successfully estimate the cyanide consumption based on mineralogical data with very lower number of parameters compared to empirical models present in the literature, while it offers the prediction of formation of all cyanide complexes which could be used for optimization purposes.

Jan 1, 2017

By Mohsen Mohammadi, Edward Cyr

"To date, several studies have been performed on the static mechanical properties of SLM-AlSi10Mg alloy. There have also been more recent studies on the relation between scan strategy, texture, and mechanical properties of SLM metals and composites. However, there is a huge knowledge gap in the available literature regarding texture and mechanical behavior of SLM-AlSi10Mg alloy under high strain rates. Therefore, in this study, dynamic mechanical behavior of AlSi10Mg_200C alloy manufactured by DMLS technique was investigated at high strain rates ranging from 900/s to 1700/s using Split Hopkinson Pressure Bar. Texture using X-ray diffraction technique of the initial samples were measured. The yield strength, peak flow stress, and ductility increased in all samples with increase of strain rate. TEM studies have also revealed evidence of continuous dynamic recrystallization in grains after 900/s–1700/s strain-rate tests. A Taylor polycrystal crystal plasticity constitutive model was then developed to capture and predict the texture evolution and mechanical response under dynamic loading, using plastic work as a critical parameter for the onset of recrystallization.INTRODUCTION Additive manufacturing (AM) powder techniques are among the fastest advancing breakthroughs in manufacturing in recent years, defined by a bottom-up layer by layer process of joining with energy input from lasers or electron beam (Herzog et al., 2016; Gibson et al., 2015). Among alloys fabricated by SLM, AlSi10Mg is of high interest to industry and academia due to its low density, high specific strength and excellent corrosion resistance, making this alloy a viable contender for aerospace, automotive, and marine applications. Circumstances such as car crash or bird aircraft strike hazards subject potential additively manufactured AlSi10Mg parts to impact loadings. This drives an interest in understanding and predicting dynamic behaviour of these alloys. AlSi10Mg is the AM counterpart of A360 die-cast aluminum, which possess hypoeutectic microstructure (Li et al., 2015). Up to the present time, many studies have presented the mechanical properties of SLM-AlSi10Mg alloy. The mechanical properties and microstructure of AlSi10Mg produced by selective laser melting (SLM) or DMLS techniques can be controlled using different parameters, such as feedstock powder (Asgari et al., 2017), and process parameters (Olakanmi et al., 2015). The microstructure and mechanical properties of AlSi10Mg can also be controlled using post heat treatment after SLM process Li et al., 2016). The mechanical properties of SLM-AlSi10Mg are sensitive to strain rate and can both change under quasi-static (Rosenthal et al., 2017) and high strain rates (Asgari et al., 2018). However, a significant knowledge gap in available literature regarding modeling these behaviours, and especially micromechanical modeling of dynamic behaviour."

Jan 1, 2018

By V. Pouyafar

Semi-Solid metal alloys, as used in SSM processing, have a special microstructure of globular solid particles suspended in a liquid matrix, which makes them behave differently in forming processes. The sensitivity of semi-solid slurries to temperature variations and their history and rate dependant behavior, make process design and control difficult. Precise selection of the process parameters is necessary in part production. Therefore, a numerical analysis and simulation of the process can be a valuable tool in process design. In this work we proposed a structural dependent model to account for the thixotropic behavior of semi-solid metals. The parameters of the model were then determined using rheometery tests. The results show a good agreement between the model and the experiments.

Oct 1, 2011

By M. G. Lipsett

One challenge in applying information technologies in Mining is building a business case. In Mine Maintenance, there is a complex flow of information that contributes to making informed business decisions. By understanding those information relationships and the cost of wrong decisions, analysts can estimate the value of information flow. Developers can then ensure that systems deliver key information in an accurate and timely way. In this paper, general maintenance decision-making is discussed, with examples of how model-based analysis can improve the information delivered to decision makers.

May 1, 2001

By F. Simon, A. Roth, M. F. Zaeh

Applying Friction Stir Welding in an industrial environment requires knowledge about the robustness of the welding process against imperfections in the joint line resulting from production deviations of the parts to be joined or from improper clamping devices. In this work the influence of gaps on the weld quality of friction stir welded butt joints of the aluminum alloy EN AW-5083-H111 is investigated in detail using the method Design of Experiments. As independent input variables, the rotation speed, the feed rate, the tilt angle, the lateral tool offset and the gap width were chosen. Tensile strength was selected as a measure for the joint quality. Moreover, the fundamental response variables of the FSW process, such as weld temperature, axial force and spindle torque, were recorded and integrated in the empirical process model derived by regression analysis. It was found that each response variable decreases with increasing gap width, whereas the largest impact was identified for the axial force and the temperature at the weld surface. In order to improve the joint strength for a given gap width, increasing the rotation speed and the tilt angle or lowering the feed rate, respectively, proved to be a suitable approach. However, interactions between the tilt angle and the rotation speed have to be considered.

Jan 1, 2014

By Chris Ryan

Operational excellence along with the need for a capital management strategy demanded an educated budgetary retirement age for haulage fleets, with uniform applicability. Given fleet size and volume of data for the Komatsu 830E fleet within Teck, this unit type was selected for development of a retirement age model suitable for all operations. The model is designed to act as a capital planning and fleet management tool aimed at minimizing costs. Life cycle parameters were examined to facilitate a visual and numerical representation of a fleet over a period of time. Physical availability and operating cost models were developed to obtain an understanding of the life cycle. These models became the drivers behind the fleet-wide retirement model. A wide analysis range of the equipment life cycle was used as it assured that the optimum retirement regime would be accurately captured. Average annual spend, including cost of operating and ownership was measured against the corresponding retirement age. Targeting the minimum within this range yielded the optimal retirement age.

May 1, 2010