Search Documents

By Pierre Gaucher

It is possible to selectively mine an orebody by combining the use of the SSW probe with any bulk mining methods as well as narrow vein exploitations. In other words, thanks to the use of the SSW probe, mining operators will be able to reduce and control dilution that is generally associated to every mining operation. Already, quick and substantial savings have been obtained. Falconbridge mines have demonstrated in Sudbury and Raglan operations, that the SSW probe can log nickel, copper and iron sulphides in blast holes. They have raised the grade and reduced dilution by outlining the limits of the ore zones before selectively loading explosives in the blast holes. By lowering the probe in a blast hole, a profile of the ore content is instantly measured and recorded. Logging cored diamond drill holes at the mine have demonstrated that the ore content (nickel, copper, cobalt, PGM) as assayed is proportional to the intensity of the probe?s electromagnetic response (EM), probably because the nickel / pyrrhotite ratio is uniform within a given orebody. The probe also measures the intrinsic conductivity of the sulphides and the percentage of magnetite. All probe readings are displayed and automatically stored at a 10-cm interval within the same reading unit. A 30-meter blast hole takes less than 2 minutes to survey. The whole instrument is light (12 kg) and very simple to use. One operator can carry the SSW system and survey either down or up-holes. The probe works from ?40°C to +50°C. Plotting the measurements of the SSW probe in blast holes (2-3-4-6-10 inches in diameter) before blasting allows to determine the exact shape of the orebody within the waste rock and uneconomic low-grade ore. Thus, only the portion of the holes that contains ore is blasted. The dilution is then much reduced and, by leaving the waste and low-grade ore in place, the mine saves on transportation, blasting, crushing, backfilling, milling, etc. Thousands of dollars are thus saved. Some savings may also be achieved during the development of stopes by guiding development drifts and by replacing diamond drilling by percussion drilling. In some circumstances, when the probe shows that some of the rich ore was not drilled-off, additional blast holes will allow to recover pockets of rich ore that otherwise would have been abandoned in the walls of a stope.

Oct 1, 2001

By Marcel Vallee, Fernand Dubuc

"The St-Honoré carbonatite complex, located 8 miles north of Chicoutimi, Quebec, was discovered in September 1967 as abnormal radioactivity was detected in the course of SOQUEM's aerial surveys. The complex, covered by a shallow layer of Trenton limestone, has been explored by aeromagnetic, ground gravimetric and magnetic surveys, and 12,013 feet of diamond drilling. Its age, from potassium-argon dating, is 650 million years. The carbonatite is approximately kidney-shaped and has a surface area of 6 square miles, 20 per cent of which is explored. It shows a central core of coarse-grained massive dolomitic carbonatite and an outer ring of foliated dolomitic carbonatite.The exploration work to date has resulted in the discovery, in the foliated carbonatite, of an incompletely drilled niobium (columbium) zone of pyrochlore-bearing carbonatite, at least 1,000 by 800 feet in size. This zone contains 5,000 tons per vertical foot grading 0.86 per cent Nb205 or at least 15,000 tons per vertical foot grading 0.66 per cent Nb205 or 45,000 tons grading 0.48 per cent Nb20s. The pyrochlore contains an average of 64 per cent Nb,Os. The central core contains a zone of rare-earth-bearing carbonatite (as monazite), grading up to 4.5 per cent rare-earth oxide, 3,500 ppm zinc and 290 ppm molybdenum. Stocks of nepheline syenite and magnetite diorite accompany the carbonatite. The total analysis and trace-element contents of typical rocks are presented."

Jan 1, 1970

By A. F. Matheson

The St. John Del Rey Mining Company, Limited, is an English company owning 150 square miles -of mining lands near Belo Horizonte, Minas Geraes, Brazil. The area is 2,300 to 5,000 feet above sea level, with a pleasant and healthy climate. Bedrock is Precambrian. The Nova Lima series of metamorphosed sediments and some volcanics is overlain uncomfortably by the Minas series of quartzites, itabirites. etc. Batholithic granite and gneiss cut both series and basic dykes cut all these rocks. There are important deposits of gold, iron, and manganese on the Company's holdings, as well as occurrences of arsenic, antimony, cobalt, nickel, dolomite, day, quartz, -ochre, bauxite, kyanite, and asbestos. Except for gold and consequent recovery of arsenic, all the other materials are relatively unexploited. The Company operates the Morro Velho gold mine and the Espirito Santo and Raposos gold mine. The Morro Velho mine was purchased in 1834 for £56,000. To the end of 1952 it had produced 7,000,000 troy ounces of gold from 15,000,000 short tons of ore. The ore z?ones are replacement deposits in a sinuous siliceous dolomitic rock locally termed "lapa seca," and plunge east, near surface at 45 °, at 8,000 feet at 15°. The ore minerals are pyrrhotite, arsenopyrite, pyrite, and chalcopyrite. Gold is finely distributed and almost nowhere visible. Ore reserves at the end of 1952 were estimated at 5.5 million short tons grading 0.39 oz. gold per ton. Chances exist for new ore within the mine area. The Espirito Santo and Reposos mine, in folded banded iron formation, has mineralization similar to Morro Velho but sulphides are less abundant. The mine to a depth of 2,500 feet has estimated ore reserves of 1.5 million tons of an average grade of 0.28 oz. gold per ton. New ore may be expected both laterally and at depth. To the end -of 1952, the ?Company had paid dividends of almost £4,- 600,000, largely earned from the operation of the gold mines.

Jan 1, 1956

By Tassos Grammatikopoulos

The St. Lawrence deposit is a large wollastonite skarn (ca. 9 Mt @ 41.3% wollastonite) adjoining the gabbroic-to-syenitic Leo Lake pluton in the granulite facies of the Frontenac Terrane of the Grenvillian Central Metasedimentary Belt. It occurs within a horseshoe-shaped horizon of quartzite, open to the east. The skarn extends over 1.2 km2, and comprises wollastonite-dominant, wollastonite-clinopyroxene, and diverse quartz-feldspar-sulphide (-titanite) layers, interbanded with, and strongly folded within, the quartzite. As in the world-class wollastonite deposits of the Willsboro district, New York State, no carbonate protolith is preserved and calcite is a negligible constituent of the mineralized zones. Wollastonite development is nonetheless ascribed to metasomatism of a metacarbonate unit by magmatogene, silica-rich, CO2-poor (XCO2 < 0.05) fluids, at P = 350 MPa and ca. 560 oC, or, alternatively, 550 MPa and ca. 630 oC. Several high grade zones, averaging >40%, but locally exceeding 80%, of translucent, white, tabular wollastonite grains, with lengths of 0.2 - 2 cm, have been delimited by drilling. Preliminary beneficiation studies yield high aspect-ratio and high-purity (low Fe and Mn) concentrates. St. Lawrence compares favourably to other known prospects and operating wollastonite deposits; having good chemical and physical properties, low iron content, and high aspect ratios (>20:1). In addition, the deposit has a favourable size and location, and will benefit from a low Canadian dollar. Canada currently has no wollastonite production.

May 1, 2002

By T. A. Grammatikopoulos, B. Vasily, A. H. Clark

"The St. Lawrence deposit is a large wollastonite skarn (ca. 9 Mt @ 41.3% wollastonite) adjoining the gabbroic-to-syenitic Leo Lake pluton in the granulite facies Frontenac Terrane of the Grenvillian Central Metasedimentary Belt. It occurs within a horseshoeshaped horizon of quartzite, open to the east. The skarn extends over 1.2 km2, and comprises wollastonite-dominant, wollastonite-clinopyroxene, and diverse quartz-feldspar-sulphide (-titanite) layers, interbanded with, and strongly folded within, the quartzite. As in the world-class wollastonite deposits of the Willsboro district, New York, no carbonate protolith is preserved, and calcite is a negligible constituent of the mineralized zones. Wollastonite development is nonetheless ascribed to metasomatism of a metacarbonate unit by magmatogene, silica-rich, CO2-poor (XCO2 < 0.05) fluids, at P = 350 MPa and ca. 560°C, or, alternatively, 550 MPa and ca. 630°C.Several high-grade zones, averaging >40% but locally exceeding 80%, of translucent, white, tabular wollastonite grains, with lengths of 0.2 cm to 5 cm, have been delimited by drilling. Preliminary beneficiation studies yield high aspect-ratio and high-purity (low Fe and Mn) concentrates.St. Lawrence compares favourably to other known prospects and operating wollastonite deposits: having good chemical and physical properties, low iron content, and high aspect ratios (>20:1). In addition, the deposit has a favourable size and location, and will benefit from a low Canadian dollar. Canada currently has no wollastonite production."

Jan 1, 2003

By T. A. Grammatikopoulos, B. Vasily, A. H. Clark

"The St. Lawrence deposit is a large wollastonite skarn (ca. 9 Mt @ 41.3% wollastonite) adjoining the gabbroic-to-syenitic Leo Lake pluton in the granulite facies Frontenac Terrane of the Grenvillian Central Metasedimentary Belt. It occurs within a horseshoeshaped horizon of quartzite, open to the east. The skarn extends over 1.2 km2, and comprises wollastonite-dominant, wollastonite-clinopyroxene, and diverse quartz-feldspar-sulphide (-titanite) layers, interbanded with, and strongly folded within, the quartzite. As in the world-class wollastonite deposits of the Willsboro district, New York, no carbonate protolith is preserved, and calcite is a negligible constituent of the mineralized zones. Wollastonite development is nonetheless ascribed to metasomatism of a metacarbonate unit by magmatogene, silica-rich, CO2-poor (XCO2 < 0.05) fluids, at P = 350 MPa and ca. 560°C, or, alternatively, 550 MPa and ca. 630°C.Several high-grade zones, averaging >40% but locally exceeding 80%, of translucent, white, tabular wollastonite grains, with lengths of 0.2 cm to 5 cm, have been delimited by drilling. Preliminary beneficiation studies yield high aspect-ratio and high-purity (low Fe and Mn) concentrates.St. Lawrence compares favourably to other known prospects and operating wollastonite deposits: having good chemical and physical properties, low iron content, and high aspect ratios (>20:1). In addition, the deposit has a favourable size and location, and will benefit from a low Canadian dollar. Canada currently has no wollastonite production."

Jan 1, 2003

By John E. Udd, Peter Leinberger, Roman Kozarycz

"This paper is based on work done by the authors in a study of the structural features at a quarry excavated in Chazy limestone on the Island of Montreal. Observations on failures on the quarry walls and benches were recorded, and back analyses of small-scale failures were carried out, thus enabling an assessment to be made of the in-situ strength properties of the rock. Using this information, and data from shear tests in the laboratory, the authors made an analysis of the stability of the south wall of the quarry.IntroductionQuarrying, and excavating for foundations, in the Montreal area involves the removal of million s of tonnes of rock on an annual basis. Even when compared with the quantities mined at major open-pit mining operations, the production figures are impressive. At present, for example, crushed stone is produced at almost 20 quarrying operations either on, or near, the Island of Montreal. The annual capacities of the larger quarries are in excess of one million tonnes each. Lesser, but still substantial, production is achieved at the smaller quarries.Excavations, for foundations , especially during periods of peak construction activity, must also involve large quantities of rock . The writers, however , are not able to produce an estimate of the actual annual tonnages originating from excavations."

Jan 1, 1981

By C. G. Bruce

"ON NOVEMBER 15th, 1950, the Department of Mines and Technical Surveys announced the discovery of vermiculite near Perth, Ontario. The announcement followed nearly a month of study to determine so far as possible the potentialities of the deposit and quality of the material from surface indications. The mineral was identified by the writer in the field among samples submitted by Mr. Arthur Powers of Stanleyville or, September 22nd, 1950. Within a week of the announcement, mining rights to properties covering a major portion of the deposit had been acquired by commercial interests.Hitherto, Canada has had to import her entire requirements of vermiculite. Prospects of .a domestic supply gave promise of considerable benefit to many industries, particularly the building industry, and to the consumer public. Should the deposit •prove large enough there was also the possibility of exporting to centres in the United States.Field and laboratory studies were continued at the Mines Branch during the winter of 1950-51 as opportunity occurred. It is the purpose of this paper to describe the results of these •preliminary investigations, to attempt to present the Stanleyville occurrence in its proper perspective with regard to similar occurrences elsewhere, and to review the salient features of the vermiculite industry.Properties and UsesVermiculite is a hydrated magnesium aluminum silicate. In appearance it resembles mica, having the same micaceous cleavage, but it differs from that mineral in being very soft, pliable, and inelastic. Colours range from black through dark olive-green and brown to almost colourless."

Jan 1, 1952

By T. Patching

"MINING operations at the Star Key Mine provided an example of a small-scale prairie-type coal mine that employed several interesting procedures and achieved good productivity with low capital expenditures. The mine was located about 11 miles north of the city of Edmonton, on the north side of the Sturgeon River valley. It opened in 1945 and operated until 1979. Output in the winters reached about 500 tons a day in the late 1940s, but in the spring and summer periods activity was usually limited to only servicing and development work. In the later years of the mine's life sales fell to less than 100 tons per day. Most of its output was bought for domestic use in furnaces and stoves so production of large sizes was desired. A modest market for stoker coal did exist for a time. Screenings (-5 / 8 in.) were sold to the city's power plant until it converted to natural gas and were also used for thawing frozen ground for work on pipelines. These markets were comparatively small and the small sizes did not command as high a price as did the larger sizes. However the extension of natural gas services to rural markets cut into the domestic heating market and finally led to closure of the mine. The coal was strong when freshly mined, but because of its high inherent moisture content, about 25%, it did not store well on surface but tended to disintegrate. It was of subbituminous Crank with a heating value of about 8000 Btu per pound and burned with a clean flame. The seam mined was in the Edmonton Formation, of Upper Cretaceous age, at a depth of 60 to 80 ft below the surface. The seam in the mine area was about 11 feet in thickness but thinned gradually to the north and south and split to the west (1). It was approximately horizontal but gentle rolls in the floor of several feet in height necessitated brushing in places to produce suitable haulage grades. The floor material was of bone and clay, overlying a thin layer of coal. Above the seam there were only a few feet of mudstones and weak sandy shales while the remainder of the overburden was clay and unconsolidated glacial till and surface soil. Because of the soft floor and weak roof material the miners usually left about a foot of coal in the floor to provide a firm working surface and about a foot of coal above the rooms and two feet of coal above the entries to provide a competent roof."

Jan 1, 1985

By Doug Smith, Ross MacFarlane

"The Star Lake Mill was commissioned by Cameco (formerly Saskatchewan Mining Development Corporation) in 1986 to process a small high grade gold deposit in a remote location of Northern Saskatchewan. The lean approach to the 200 t. p. d. CIP mill to minimize capital and operating costs employs a number of unique features which are described along with highlights from the initial two years of operation.1.0 INTRODUCTIONThe Star Lake Mine is located 520 kilometers north of the City of Saskatoon (Fig. l) with the nearest population centre in La Ronge 130 km to the south. Gold showings were first discovered in the area in the 1940's with the Star Lake ""21 Zone"" ore body discovered in 1983. The Star Lake Mine started operations in 1986 becoming the first primary gold producer in Saskatchewan in over 40 years. The mine is operated by Cameco (formerly SMOC) with 50\ ownership in a joint venture with starrex Mining Corporation (35\) and Uranerz Exploration and Mining (15%).The limited reserves coupled with the remote location and the price of gold ($300-$350 u.s./oz) at the time the project feasibility was being assessed required a lean approach to make the short term operation successful. This paper describes the approach taken in the design and construction of the Star Lake Mill and describes the mill operation with highlights of the initial two years of operation."

Jan 1, 1989

By J. C. O'Rourke

"Gibraltar Mines Ltd. has been operating its open pit copper mine for fifteen years. In that time, over 140 million tons of waste and low-grade material has been placed on the mine waste dumps. Laboratory and in situ testing indicated that enough leachable copper was recoverable from the dumps to justify a leaching operation which would include the construction of a solvent extraction-electro winning plant. The plant, which was commissioned in October 1986, was designed to process 3000 USGPM of dilute copper solution to produce 5000 tons per year of high-quality cathode copper.This paper deals with the start-up and initial year of operation of this plant. The three areas: leaching, solvent extraction, and electrowinning are presented with emphasis on the innovations which were made to help overcome the problems unique to the Gibraltar operation.The Leaching CircuitThe mine waste dumps are leached to produce a pregnant copper solution as feed to the SX-EW plant. To achieve this the dumps are sprinkled with a mildly acidic solution which percolates through the dumps. In travelling through the dumps the solution contacts the surfaces of the liberated copper minerals and dissolves the soluble copper into the form of copper sulphate. The leaching reaction is achieved by a combination of bacterial action to oxidize the sulphides and solubilization of the copper into the acid solution.For the bacterial action to occur the dumps must be near the ideal pH of 1.9 to 2.1 and the necessary elements of the reaction must be present. Because a bacterial reaction is involved there is a lag time between the time when the conditions for bacterial growth are achieved and when the bacteria are in their active growth phase. Laboratory leaching tests with Gibraltar ore indicated that bacterial action takes two to three months to reach its maximum rate (Fig. I).The expected lag time for the planned rate of bacterial leaching prompted Gibraltar to start irrigating the dumps in late June 1986 for a plant start in early fall. The lag time proved to be longer than expected and the dumps took until November to start producing copper at the expected rate (Fig. 2)."

Jan 1, 1988

By J. C. O'Rourke

"Gibraltar Mines Ltd. has been operating its open pit copper mine for fifteen years. In that time over 140 million tons of waste and low grade material has been placed on the mine waste dumps. Laboratory and in-situ testing indicated that enough leachable copper was recoverable from the dumps to justify a leaching operation which would include the construction of a solvent extraction-electrowinning plant. The plant, which was commissioned in October, 1984 was designed to process 3,000 usgpm of dilute copper solution to produce 5,000 tons per year of high quality cathode copper.This paper deals with the start up and initial year of operation of Gibraltar's SX-EW plant. The three areas: leaching solvent extraction and electrowinning are presented with emphasis on the innovations which were made to help overcome the problems unique to die Gibraltar operation.THE LEACHING CIRCUITThe mines waste dumps are leached to produce a pregnant copper solution as feed to the SX-EW plant. To achieve this the dumps are sprinkled with a mildly acidic solution which percolates through the dump. In travelling through the dumps the solution contacts the surfaces of the liberated copper minerals and disolves the soluble copper into the form of copper sulphate. The leaching reaction is achieved by a combination of bacterial action to oxidize the suphides and solublization of the copper into the acid solution.For the bacterial action to occur the dumps must be at or near the ideal pH of 1.9 - 2.1 and the necessary elements of the reaction must be present. Because a bacterial reaction is involved there is a lag time between the time when the conditions for bacterial growth are achieved and when the bacteria are in their active growth phase. Laboratory tests with Gibraltar ore indicated that bacterial action takes two to three months to reach its maximum rate. See figure 1.The expected lag time for the planned rate of bacterial leaching prompted Gibraltar to start irrigating the dumps in late June 1986 for a plant start up in early fall. The lag time proved to be longer than expected and the dumps took until November to start producing copper at the expected rate. See figure 2."

Jan 1, 1988

By J. D. Clucas, D. B. Dreisinger

"The Starved Acid Leach Technology (SALT) has been developed by Search Minerals to extract nickel and cobalt VALUES (from nickel laterite ores (saprolites) and Caron plant residues. The technology consists of sulfuric acid atmospheric leaching of the ores or residues followed by neutralization and recovery of nickel and cobalt. The acid addition is carefully controlled to maximize nickel and cobalt extraction while minimizing overall consumption of acid by various gangue reactions. The final recovery processes can be tailored for maximum economic benefit. The use of resin-in-pulp processing is advocated as the most cost effective method for initial recovery of nickel and cobalt from lower grade materials. INTRODUCTIONCommercial processes for laterite ore treatment vary according to laterite type and local conditions. The two general categories of laterite ore are saprolites and limonites.Saprolites are generally treated by pyrometallurgical processes for reduction of nickel to matte or ferro nickel alloys. The high cost of drying, chemical reduction and electric furnace smelting requires that the saprolite grade for economic processing is of the order of 1.8% nickel or higher. There are of course large amounts of saprolite that fall below this “cut-off” grade that are not currently economic.Limonites can be treated by the Caron Process which involves drying of the ore, a reduction roast of the whole ore to reduce nickel and cobalt (and some iron) to the metallic state followed by ammonium – ammonium carbonate solution to leach nickel and cobalt. Nickel and cobalt recovery are low (70-85% for Ni and 20-50% for Co). The Caron plant tailings therefore contain high levels of unrecovered nickel and cobalt. Relatively few plants have used the Caron Process and new installations are not anticipated due to the high energy cost of drying and reduction roasting. Nevertheless, plants in Brazil (Niquelandia), Australia (Yabulu) and Cuba continue to operate.The high pressure acid leach (HPAL) process was pioneered at Moa Bay in Cuba in the 1960’s in the treatment of limonites. In the 1990’s the HPAL process was touted to revolutionize the nickel industry with low capital and operating costs for new installations. Murrin Murrin, Cawse and Bulong in Australia were started and in each case the technical difficulties of operating at extreme temperature and pressure conditions and the challenges in “ramping up” a complex hydrometallurgical facility conspired to cause these plants to fail economically. At present, Cawse and Bulong are closed and Murrin Murrin continues to operate after undergoing a financial restructuring."

Jan 1, 2012

By N. Waters

"Nickel saprolite ores are normally mined as feed to Fe-Ni smelters or Ni matte smelting operations. The smelting processes typically require high Ni cut-off grades of approximately 1.5 to 2.2% Ni, depending on the operation. These very high cut-off grades result in a significant portion of the saprolite profile being regarded as “waste” and hence having little to no value. The Starved Acid Leach Technology (SALT) was developed to recover nickel and cobalt from nickel saprolites and Caron plant residues. Relatively small amounts of acid are applied to ground saprolites or Caron residues in order to selectively leach nickel and cobalt. The leaching is performed atmospherically under low free acid conditions. Nickel and cobalt may be recovered from the leachate as a mixed hydroxide. The mixed hydroxide may be added directly to a saprolite smelting operation or refined separately. InCoR Technologies is advancing the application of SALT at a number of sites. Bench scale testing has provided a relationship between acid addition and nickel extraction in leaching. Conceptual engineering studies have been completed by SNC Lavalin. The simplicity of the SALT technology provides the benefits of low capital and operating cost and an expected rapid ramp up to full production.INTRODUCTION The recent history of hydrometallurgical nickel laterite treatment plants has demonstrated mixed financial and operational performance. Table 1 summarizes the next generation plants built after the financial and/or technical failure of the Bulong, Cawse and Murrin-Murrin plants in Australia. The Coral Bay plants (Line 1 and 2) stand out (and now Taganito) as relatively low capital cost, simple (no acid plant, production of mixed sulfide product), and modest in scale (10, 12 and 36 kt Ni/a). However, the other plants in the list (Ravensthorpe, Ramu, Goro and Ambatovy) are all characterized by financial and technical challenges. All plants have a very high capital cost ($67,000 to $120,000 USD/annual t of Ni production). Ravensthorpe was sold by BHP Billiton after a poor startup. Ramu has had a steady ramp up but only produces mixed hydroxide for refining by others. Goro has had an extended construction period (since 2001), is high cost and has been very slow to ramp up to design production rates. Ambatovy has had a steady ramp up."

Jan 1, 2017

By P. Pyykkö, E. Peuraniemi, J. Järvi, P. V. Latostenmaa, V. Törölä, S. Junnikkala

"Nickel concentrate smelting started in Harjavalta in 1959. First, flash smelting - Peirce-Smith converting route was applied, and the high-grade converter matte was further refined to nickel cathodes. In 1995 the original smelter flow sheet was simplified with the novel DON (Direct Outokumpu Nickel) technology. In Harjavalta with the DON technology, high-grade nickel matte with low iron content is produced in flash smelting furnace directly without subsequent converting stage. The metal values in the smelting slag are recovered in an electric furnace as an iron containing bottom alloy. Main special features in Boliden Harjavalta nickel smelter are smelting of high-magnesia concentrates, the high recoveries of nickel and copper, as well as those of PGM`s and cobalt.Sulfur and dust emissions to air can be seen generally as one main disadvantage of nickel smelting operations. In Harjavalta continuous improvements in environmental performance has been rewarded by minimum sulfur and dust emissions to the environment and working atmosphere. Today Boliden Harjavalta’s nickel smelter is presenting state-of-art-technology at nickel smelting.This paper describes the nickel smelter process and includes recent production and emission data. It describes features required to achieve environmental and occupational hygiene goals and compares environmental performance data to that published on other smelting operations. General description of New Boliden Way is presented and a case example of production stability project is also presented."

Jan 1, 2014

By R. Hammen, J. Lifton

"The purification of rare earth elements (REE) at mining operations is traditionally accomplished by multiple chemical phase-transfer processes including precipitation, solvent extraction, and ion exchange. We describe REE purification results with Solid Phase Extraction (SPE) columns that were developed to improve the speed and economy of REE purification. The SPE columns have the properties of enhanced equilibration kinetics, so that residence time of a few seconds will accomplish selective chemical transfers from solution phase to solid phase. We describe the separation of REE’s as a class from leach solutions and the further purification of REE salts. INTRODUCTIONHistorically the rare earths were first chemically separated from each other and purified by fractional crystallization. This slow, cumbersome, and laborious process was not suited to commercial production. Solvent Exchange (SX) technology was applied to the problem of separating and purifying the rare earth elements when it was determined in the late 1960s that there might be commercial uses for them individually. At the same time the very slow and expensive technique of ion exchange was applied either for ultra-purification of the desired “light” rare earths, or for the recovery and purification of the tiny amounts of higher atomic numbered, “heavy,” rare earths. Solvent Exchange (SX) has today become the standard for separating the rare earths across their atomic number spectrum. Whereas the separation of the light rare earths commercially may take 30 “cascades’ in a modern Chinese plant, the total separation of all of them from each other may take up to 80 such “cascades,” and is only even “practical’ with preconcentrated feed stocks, such as those produced in China by heap-leaching techniques performed in situ on very low grade radio-nuclide free ionic absorption clays.. Ultra-pure materials of all types are produced today by ion-exchange processing of ionic species already separated by solvent exchange.Hard rock deposits and refractory residues of tin mining and residues from uranium mining have been identified outside of China with very high ratios of dysprosium and other heavy rare earths to the majority lighter ones. Several issues face those who wish to process these materials so as to separate the heavy rare earths commercially:"

Jan 1, 2012

By H. H. Fairfield

THE production and inspection of the materials of war involves thousands of observations. Logical action is generally based on the interpretation of many observations. The success of such action depends upon the accuracy of the observations and the soundness of the interpretation placed upon them. There are countless instances where the observer &apos;sees but perceives not&apos;; that is, the significance of a group of observations is lost, due either to faulty interpretation or to no interpretation at all being placed on the results. This condition is being partly corrected in the United Kingdom and the United States (1) by the promotion of certain principles by Ordnance officials. The term Quality Control has been adopted to describe a system of studying and controlling industrial products by methods of handling observations. In these pages an attempt is made to outline in a non-technical manner some of the ideas used in the handling of observations. Of course the authenticity of the observations determines the worth of any decisions based on them. No matter how brilliant is the theory built on unreliable sampling, it is usually of little practical value. n some fields it is almost impossible to obtain observations free from bias. Let us suppose that observers of speed in miles per hour were available for judgment: (a) a bystander, (b) a motorcycle policeman, and (c) a motorist accused of speeding. The bystander might be unbiased but probably would be very inaccurate. The motorist is usually biased on the low side. The policeman is the only qualified observer and, if over-zealous, he might be biased on the high side. Conclusions drawn from large numbers of biased observations naturally would be of little value.

Jan 1, 1943

By George B. Saunders

The mines in western Canada producing steam coal will find a better opportunity this year to market their product in Winnipeg - for two reasons: First, the new wage schedules, signed with local unions at each mine, have enabled them to reduce the selling price materially. Second, the duty on slack coal coming in from the United States has been raised to 50 cents, which is equal to the duty on run-of-mine coal. This has had the effect of raising the cost of mine-run to .the importer. Formerly, it was the practice to bring in slack coal under a duty of 14 cents and lump coal under a 53-cent duty and, by judicious mixing of the two, manufacture a mine-run coal at an average duty cost of about 22 cents. Fortunately, through efforts of the Alberta Government, and other friends of the Canadian coal trade, the Federal Government was persuaded to adjust the duty on slack coal as indicated. While it will be found that the Manitoba market, this season, is slightly more easy of access we have still a long way to go before we reach the desired goal. Geographically and economically the Manitoba market should belong to western Canada. However, it has been found a very profitable market for United States mines because large tonnages of coal can be shipped, practically at the convenience of the mines, via the Great Lakes, during seasons of slack business. They will therefore not relinquish this market without a struggle.

Jan 1, 1925

The primary steel industry of the Prairie Provinces consists essentially of three companies whose total annual melting capacity, as of January 1, 1963, was 333,000 net tons. These companies have steel rolling facilities. In addition, there are five other companies producing steel castings by melting scrap in electric furnaces which, with the plants having rolling facilities, gives a total annual furnace melting capacity of 380,000 tons. Since 1954, the annual production of steel ingots and castings has ranged from a low of 66,588 tons, in 1954, to a high of 211,138 tons in 1961. The present facilities on the Prairies for making steel ingots from scrap, and rolling them to produce light merchant mill products, appear to be sufficient for many years ahead. Steel scrap, as electric furnace feed to make steel ingots for the present line of products, will probably continue to be available at reasonable prices either on the Prairies or from the north-central United States. It is recognized, however, that residual elements in scrap may be-come of greater significance and necessitate more rigid control of scrap quality.

Jan 1, 1963

By M. S. Fotheringham

Recognition of the Growing Importance of Iron and Steel Few Canadians have yet become aware that Canada&apos;s vast iron ore resources, the greater part of which is only now beginning to be developed, will inevitably have a profound effect on the entire Canadian economy, benefitting in some measure the lives of all Canadians. The great iron mining developments of Ontario, Newfoundland, Quebec, and Labrador are destined to make Canada one of the world&apos;s major producers and exporters of this material, on which our industrial civilization is?based. These developments will create new employment, new communities, new transportation facilities, and new investment opportunities. Iron ore is the foundation and the keystone of modern mechanized civilization. The most prosperous nations of the world are the highest per capita consumers of iron and steel, and in these countries the per capita consumption is increasing steadily despite the advent of light metals, plastics, and other competitive materials. Three-quarters of the human race have too little steel -and consequently too little mechanization -to provide for themselves the necessities and comforts of civilized living. Progressively they will demand, and acquire, the machines, the transportation and communication facilities now lacking, and they will win them by making greater use of the world&apos;s iron resources. It is the good fortune of this generation that Canada&apos;s &apos;iron age&apos; is just getting well under way.

Jan 1, 1951