Search Documents

By J. Aguilar-Santillan, H. Balmori-Ramirez, R. C. Bradt, I. Vernet-Patiño, F. Cunha

Kyanite is an alumino-silicate mineral that has been widely used for the production of refractory products for industrial applications. Kyanite provides a high alumina content, it readily produces mullite during firing, good hot strength of products and can be adapted to produce dimensional stability of products during firing. This research addresses the application of kyanite in mixes to produce (0 dense mullite aggregates with the addition of alumina, (ii) dense composite refractory aggregates of forsterite / spinel with additions of magnesia, and (iii) dense cordierite aggregates with the addition of talc. Effects of attrition milling and conventional ceramic processing are addressed as they affect the properties of these unique aggregates.

Jan 1, 2004

By P. R. G. Brandão, E. E. Ferreira

The presence of metallic cations in solution will affect the aggregation or dispersion of the fine hematite particles, depending on the type of cation adsorption: either specific or non specific adsorption. In this work, the zeta potential measurements were carried out on a sample of pure hematite as a function of pH and metallic cations concentration (Ca2, Mg2+, Mn2+, K+, Na+ and Al3+). The objective of these studies was to clarify the effect of these metallic cations on the surface chemical properties of pure hematite. The cations K+ and Na+ adsorbed as non-specific species and caused only the reduction on the values of zeta potential (in terms of absolute value) over the entire range of pH values tested. For the Al3+ cation, in the acidic pH range it adsorbed as a specific species and increased the zeta potential values. The cations Ca2+, Mg2+ and Mn2+, adsorbed as a non specific species at pH levels less than 6.0 and caused the reduction of zeta potential due to the compression of the electrical double layer. However, for pH values greater than 6.0, these cations adsorbed as a specific species causing the zeta potential to increase and became more positive as the pH value increased (alkaline). This effect could be due to the adsorption of some hidroxy complex species of these cations, which contributed to the positive charge. The effect of metallic cations (Ca2+, Mg2+ and Al3+ concentration, at pH 4.0, 7.0 and 10, showed the following results: a) at pH 4.0, increasing the concentrations of Ca2+ and Mg2+ resulted in on a small reduction in the value of the zeta potential. At this pH, increasing the concentration of A131 cations caused the zeta potential to increase due to specific adsorption of a negatively charged Al3+ hydroxy complex b) at pH 7 and 10, increasing the concentrations of Ca2+ and Mg2+ caused the zeta potential to change its charge from negative to positive.

Jan 1, 2004

By Lawrence Bragg

WE associate metals with hardness, toughness, and strength. But a curious paradox lies at the root of the valuable mechanical proper-ties of the metallic state: in order to be strong, a metal must be weak. This paradox, and the equally surprising fact that, in a sense, metals are not true solids at all, are among the topics here discussed by Sir Lawrence Bragg. (1) WHAT METALS MEAN TO US We employ various materials to build or fabricate the many objects we use in everyday life, choosing those whose properties are most suitable for the purpose which the object has to serve. Certain of these materials have been used from the earliest times, such as stone, wood, leather, and animal or vegetable fibres, each with its own peculiar valuable properties. Stone resists crushing and is very durable and permanent, as indeed it must be, since it has so long resisted change as a part of-the earth's crust. It is there-fore ideal for walls and buildings, and very early in his history man discovered how to make artificial stones by burning clay, with the advantage that they could be given any desired shape, and made into bricks or given elaborate forms as pottery. Wood is strong and tough and light, it resists tension as well as compression, and is nor brittle like stone. It forms beams and furniture and parts of tools or weapons. Leather is tough but at the same time iris flexible; it is ideal as straps or sheers. Vegetable fibres such as linen or cotton, and animal fibres such as wool and silk, owe their value to their flexibility and strength in resisting extension. They can be spun into yarn or rope, and woven into cloth. The technological age in which we are now living is replacing the natural products used by early man by a series of artificial products, but it is remarkable to see how in nearly every case we are copying Nature's materials. The wide use of concrete represents a developed art of making artificial stone. Artificial fibres such as rayon or ?nylon replace cotton, wool, and flax. Plastics are coming very much to the fore; they correspond to early man's use of horn, another substance with peculiar properties of roughness in all directions without the 'grain' of wood. For the most part we are following in the footsteps of our remote ancestors, though we can make for ourselves what they had to cull from wood and field. There are exceptions; for instance, we have discovered comparatively recently the number of uses to which natural rubber can be put, and are now making it artificially. This is a really new discovery; our ancestors had nothing with such remarkable powers of elastic stretching without breaking, and resistance to being abraded.

Jan 1, 1943

By F. Habashi

In the period 1970-1995, a number of hydro metallurgical processes to treat copper concentrates to overcome the pollution problem due to S02 emission in smelters were developed. Pilot and commercial scale plants were built and operated for some time, but eventually all were abandoned a few years later. It is constructive to examine why these processes were abandoned after so much expenditure of funds and effort, so that errors should not be repeated in the future and lessons from the past are learned.

Jan 1, 2007

By J. E. Rehder

IN A DISCUSSION of use of any material of ?construction in the mining industry, two points of view must 'be kept in mind - that of the producer or manufacturer of mining and metallurgical equipment, and that of the maintenance and operating staff of the mining plant. In the first case, the choice of material of construction is up to the manufacturer and the user of the equipment has little direct say in the matter. However, if materials are badly chosen and the equipment does not function properly, wears out rapidly, or costs too much, repeat orders ?will likely go to a different manufacturer, so that, in the end, the consumer or mine operator does have the final voice. In the case of materials for maintenance work and plant operations, however, .the mill personnel have direct control over purchases and it is then that a well-balanced knowledge of materials, their properties, and their costs, can be directly useful. With all materials of construction, the final criterion is unit cost versus service performance, so that the lowest possible total operational cost will be obtained. Sometimes this means using the cheapest material available, sometimes the most expensive, but in any case careful analysis of service performance, replacement cost, and material cost is essential to determining the material that produces lowest total cost.

Jan 1, 1956

By J. C. O'Rourke

"Gibraltar Mines Ltd. has been operating its open pit copper mine for fifteen years. In that time, over 140 million tons of waste and low-grade material has been placed on the mine waste dumps. Laboratory and in situ testing indicated that enough leachable copper was recoverable from the dumps to justify a leaching operation which would include the construction of a solvent extraction-electro winning plant. The plant, which was commissioned in October 1986, was designed to process 3000 USGPM of dilute copper solution to produce 5000 tons per year of high-quality cathode copper.This paper deals with the start-up and initial year of operation of this plant. The three areas: leaching, solvent extraction, and electrowinning are presented with emphasis on the innovations which were made to help overcome the problems unique to the Gibraltar operation.The Leaching CircuitThe mine waste dumps are leached to produce a pregnant copper solution as feed to the SX-EW plant. To achieve this the dumps are sprinkled with a mildly acidic solution which percolates through the dumps. In travelling through the dumps the solution contacts the surfaces of the liberated copper minerals and dissolves the soluble copper into the form of copper sulphate. The leaching reaction is achieved by a combination of bacterial action to oxidize the sulphides and solubilization of the copper into the acid solution.For the bacterial action to occur the dumps must be near the ideal pH of 1.9 to 2.1 and the necessary elements of the reaction must be present. Because a bacterial reaction is involved there is a lag time between the time when the conditions for bacterial growth are achieved and when the bacteria are in their active growth phase. Laboratory leaching tests with Gibraltar ore indicated that bacterial action takes two to three months to reach its maximum rate (Fig. I).The expected lag time for the planned rate of bacterial leaching prompted Gibraltar to start irrigating the dumps in late June 1986 for a plant start in early fall. The lag time proved to be longer than expected and the dumps took until November to start producing copper at the expected rate (Fig. 2)."

Jan 1, 1988

By S. Jain

Construction industry is considered as labour intensive, having shortage of skilled labour, unsafe with large number of industrial accidents. Construction industry requires high technology automation products (Robots) for improving productivity, safety, quality etc. Robots are developed by various countries in different areas like demolition, earthwork, bridge, tunnels, road work, underwater works, trenches and piping, maintenance etc. however they are still not used to their full potential by construction industry. Hence in this paper, the authors propose a ?model for adoption? of robots in construction industry. This model considers how a construction firm will adopt full scale robots like manually controlled machine, tele-controlled machines, computer controlled machines and cognitive robots and assimilate them through various stages.

Aug 1, 2013

By F. J. Gauthier, R. G. Gray

"The possibilities of expanding the production rate from the Copper Mountain Mine have been examined using computer programs for analysing a complete range of data, beginning with the diamond drill assays and embracing all steps up to the final rates of return.Programs have been developed to calculate the mineralization inventory file, a matrix of blocks containing the grade and the type of mineralization estimated for each block. Given the topography, prices of metals and costs, the pit limits are optimized using a three-dimensional technique. Within the pit, ore reserves at any cutoff can be calculated. Mining of the pit is then simulated using an interactive production scheduling program on a timesharing computer. The annual tonnage and grade figures from the production schedule are input to a financial analysis program, where the present value and the rate of return are calculated at various metal prices. The expansion possibilities can be run through the programs with their respective costs, and evaluated using the rate of return on the marginal cash flow compared to the additional capital expenditure."

Jan 1, 1971

By A. Welty, T. Garn, K. Lyon, B. Jakovljevic, R. S. Herbst, M. Greenhalgh, Cytec Solvay Group

"Industrial rare earth separation processes utilize PC88A, a phosphonic acid ligand, for solvent extraction separations. The separation factors of the individual rare earths, the equipment requirements, and chemical usage for these flowsheets are well characterized. Alternative ligands such as Cyanex® 572 and the associated flowsheets are being investigated at the pilot scale level to determine if significant enhancements to the current separation processes can be realized. These enhancements could be defined as higher separation factors, reduced stage requirements, or reduced chemical consumption. Any of these enhancements can significantly affect the costs associated with these challenging separation proccesses.A mid/heavy rare earth element (REE) separations flowsheet was developed and tested for each ligand in a 30 stage mixer-settler circuit to compare the separation performance of PC88A and Cyanex® 572. The ligand-metal complex strength of Cyanex® 572 provides efficient extraction of REE while significantly reducing the strip acid requirements. Reductions in chemical consumption have a significant impact on process economics for REE separations. Partitioning results summarized Table 1 indicate that Cyanex® 572 offers the same separation performance as PC88A while reducing acid consumption by 30% in the strip section for the mid/heavy REE separation."

Jan 1, 2016

By Rodney Trevor Jones, Arthur Robert Barnes

Anglovaal Minerals acquired the Nkana slag dump from Zambia Consolidated Copper mines (ZCCM) in 1998 and embarked on an ambitious project to pioneer the recovery of cobalt from slag using DC smelting technology. Anglovaal Research Laboratories performed initial pioneering smelting tests in a 250 kW DC furnace over a 3-year period before engaging Mintek for three piloting campaigns at the 1.5 MW level. Mintek had previously developed a reductive smelting process, patented in 1995, using a DC arc furnace for the recovery of cobalt from slags. The results of the pilot-plant test campaigns were used as the basis for engineering the commercial 40 MW operation installed at Chambishi Metals plc in Zambia in 2001. This paper traces the development of understanding of the metallurgical fundamentals ultimately used to predict furnace performance, reviews some of the extreme technical challenges faced, how solutions were identified and highlights some of the critical issues identified during piloting and how these impacted both positively and negatively on the final commercial operation.

Jan 1, 2011

By Scott A. Stebbins

Cost evaluation models constructed specifically to evaluate the economic potential of an individually motorized railcar system of ore and waste transport demonstrate that the approach may be considerably more cost effective than traditional rubber-tired haulage methods. The system design places a motorized drive unit on each railcar, as opposed to the more common configuration in which a series of un-motorized cars trail behind a single locomotive. These motorized railcars are directed to various load and dump points by a computerized dispatch system, and as such have the advantage of operating unmanned. In addition, the tractive effort of the rail-type drive system is noticeably more efficient than that of the rubber-tired mode of transport. The savings are realized primarily through comparative reductions in the requirements for labor and, to a lesser degree, energy.

Nov 1, 2011

By Edmond Chow

Shovel bucket blast fragmentation analysis is an alternate way to assess blast performance and its effects on downstream mining processes. A camera is installed on the boom of cable shovels, and the stick of hydraulic shovels. Images are captured automatically as the shovel digs, and are processed to acquire rock size information. The automatic data acquisition makes this method safe to use with minimal manual labour. It also allows for a large set of sample data to be captured from both the surface and the interior of a bench face. The system has been deployed in several mines to provide an objective assessment of blasting performance. Images are captured from their cable or hydraulic shovels. The images are grouped into sets based on the shovel location and time to match the fragmentation to specific blasts. Blast fragmentation reports are created for each blast after reviewing the results. Measuring blast fragmentation from the shovel bucket proves to be an effective alternative for blast performance assessment with unique advantages. The blast fragmentation information has been valuable to the mines, and the mines have begun adopting it into their operations.

May 1, 2011

By Jessica Egan, Daniel Hodouin, Mohammed Reza Khalezi, Steve Bellec, Claude Bazin, Carl Duchesne

"A model for gold leaching was developed and implemented into a simulator. The simulator uses a description of the ore that is based on the mineral composition and precious metal content. The model accounts for the distribution of minerals and precious metals through the size intervals. An ore texture model based on precious metals and minerals grain sizes within the ore is used to predict the exposed surface of the species in the various size intervals. A model is proposed to predict the rate of dissolution of any species dissolution using the exposed surface, particle size, cyanide and oxygen concentrations, temperature, pH and agitation. The flow of slurry through a leaching tank is modelled using a parallel arrangement of perfect mixers to simulate a bypass and a Cholette-Cloutier mixer model. The simulator can be used for circuit optimization but was developed to provide an environment for learning the basic concepts of process analysis methods. Examples are given to illustrate the application of the simulator for planning tracer tests and sampling campaigns.INTRODUCTIONThe constant pressure to improve the operation of processes that are already close to optimum imposes to plant engineers to be aware of the available process analysis tools and to be able to use them to assess process operation and make a diagnosis to possible problems. Some of these tools are:•,Sampling the streams of a process;•,Data reconciliation;•,Analysis of mixing in reactors;•,Estimation of rate parameters;•,Optimal tuning and flow sheet modification;•,Automatic control and real time optimization.Although some of these tools are part of the curriculum of many university engineering programs, the students are not exposed to actual process analysis problems. In addition the complexity of the ore dressing processes compounded with unavoidable measurement errors and plant disturbances can discourage many motivated engineers. These factors often lead to an incomplete valorization of the collected data and a poor return on the investment associated with the sampling, testing and analysis of the samples.Simulators are readily available for process optimization (Yalcin and Shang, 2006) by allowing:•,The simulation of various flow sheet configurations;•,The simulation of a change of operating conditions;•,The simulation of various control strategies;•,The training of plant operators.However few simulators have been developed with the objective of providing an environment for training plant engineers and technicians to the use of tools for process analysis and optimisation."

Jan 1, 2008

By John Taylor

"The Highvale Mine in Alberta is owned by TransAlta Utilities Corpora/ion and operated by Mana/fa Coal Lid. It is the largest coal mine in Canada and in 1982 supplied 8.6 million 1onnes of sub-bituminous ""B"" coal to TransAlta's Sundance Ceneraling Plan/. Annual produclion is scheduled to increase in 1983 when the firs/ unit of the new Keephil/s Generating Plant comes on stream and is expec/ed to exceed 11 million tonnes by 1985 when the second unit is commissioned. Coal is mined from several pits in a multi-seam operation. Comprehensive maintenance, drainage and environmental programs form a major part of the operation.IntroductionThe Highvale Mine is located eighty kilometres west of Edmonton, Alberta on the south shore of Lake Wabamun (Fig. I). The mine is owned by TransAlta Utilities Corporation (T.A.U.) and is operated by Manalta Coal Ltd. In 1982, 8.6 million tonnes of coal were supplied to T.A.U.'s 2100 MW Sundance Generating Plant, making it the largest producing coal mine in Canada. By 1985, with two 375 MW units on line at T.A. U .'s new Keephills Generating Plant, annual production is estimated to exceed eleven million tonnes. The generating plants accept crushed unwashed coal from the mine via the coal handling plant system conveyor belts. The coal is classified as sub-bituminous ""B"" and has an average heating capacity of 18.6 MJ I kg.HistoryPrior to 1943 only small scale mining took place in the Highvale area. Between 1943 and 1961 two strip mining companies, Mount Royal Collieries and Continental Collieries operated on the present mine site. Both operations excavated coal along the south shore of Lake Wabamun."

Jan 1, 1985

By B. C. Legg, G. L. Tiley

"Many of the ore bodies presently being developed are in remote locations and are, or will be, served by electrical power supply systems of limited capacity.The largest single components of the electrical systems of an underground mine are usually the production hoist drives; the power demands of these drives vary continuously throughout each hoisting cycle.Before 1970mine hoists were driven by either wound rotor induction motors or DC motors in conjunction with motor generator sets.Static Power conversion equipment now costs less to purchase and install and is claimed to be more efficient than motor generator sets. On the debit side, however, it can adversely affect the hoist motors, it operates at relatively low power factors, and it produces harmonic currents.This pa per discusses the effects of static equipment on both DC motors and AC power systems, and evaluates the relative consumption of the three classes of drives."

Jan 1, 1993

By Sina Mostaghel, M. Guo, E. Klaffenbach

The current paper is focused on evaluating the behavior of copper in a copper production slag and the assessment of metal recovery possibilities. For this reason, thermodynamic calculations were carried out to determine the influence of parameters such as slag composition, temperature and oxygen partial pressure on recovery of non-ferrous elements. It was found that the formation of a solid face centered cubic (fcc) phase, mainly consisting of iron, limits the extent of reduction that can be achieved for an industrial process. However, it could be discovered that solubility of iron in the Cu-rich liquid alloy strongly depends on presence of other elements, particularly arsenic. As part of the results of this study, the solubility of Cu in the slag at onset of fcc phase formation is presented as function of temperature, oxygen partial pressure and concentration of MgO and CaO. It was concluded that lower temperature (1200°C) and higher CaO addition (16 mass-% in this study), would result in the highest achievable copper recovery from slag. INTRODUCTION Copper slag is produced as a by-product of the copper production process. The slag is still containing a high amount of copper and other valuable metals. This demands further treatment of the slag as a secondary source of metals. In addition, the physical/mechanical properties of slag allow its use in several applications such as hydraulic engineering, civil engineering, as an abrasive and many more. These applications help reducing the use of natural resources like rock and sand. By decreasing the content of heavy metals such as Cu, Pb, Zn and As in the slag, its application in abovementioned fields becomes more attractive as the probability of releasing these elements to the environment is further reduced. To develop a pyrometallurgical slag reduction process, it is necessary to understand what describes the end point of the reduction. This point is expected at maximum copper recovery without facing operational challenges. Existing literature provide some information on the effect of different parameters such as temperature or concentration of different slag formers, on solubility of copper and heavy metals in different phases. However, due to complexity of industrial slags, equilibrium experiments and accurate thermodynamic modelling are essential to be able to reliably predict the behavior of different elements in the system and determine the end-point of reduction.

Jan 1, 2019

By G. G. Hatch

FOLLOWING World War II there was an urgent need for the development of domestic sources of ilmenite to take care of the expanding needs of the titanium dioxide pigment industry. In addition, there was the interest by the pigment manufucturers and others in titanium metal. Prior to the war the pigment industry in the United States had obtained its major tonnage of ilmenite, analyzing 55- ?60 per cent Ti02, from India. However, as a result of the shipping situation which developed during the war, the pigment manufacturers had to consider the use of lower grades of ilmenite located on this continent .and several companies undertook extensive exploration programmes to locate and develop such orebodies. Probably the most significant deposit that was found as a result of these ?programmes was the orebody .at Allard Lake, Quebec, owned by the Quebec Iron and Titanium Corporation. This ?Company was formed in 1948 by the Kennecott Copper Corporation and the New Jersey Zinc Company to mine this ilmenite ore and treat it in electric furnaces to produce titanium dioxide slag for the pigment industry and iron for the steel industry.

Jan 1, 1956

By W. Beres, R. E. Miller, B. Shiari, L. R. Zhao

A dynamic multiscale (MD/FE) method has been used to study dislocation generation and plastic deformation during a nanoindentation process which is physically associated with the generation of heat within the specimen and as a consequence with a temperature rise. Two different techniques are applied to study the temperature effect on the nanoindention process. In the first technique, a global Nose-Hoover thermostat is applied to the entire atomistic region to keep temperature constant during simulation (finite temperature approach). In the second method, the thermostat is applied only on a damping region along the MD/FE interface. Both techniques are able to effectively and efficiently absorb high frequency reflected waves from atomistic/continuum interface. The temperature profile of the atomistic region beneath the indenter is reported and discussed at four different initial substrate temperatures for both techniques. The loaddisplacement (load/unload) curves for different temperature-controlling techniques are compared and discussed. The nucleation and propagation of dislocations in the atomistic region are investigated for both techniques. Correlations between the observed features in the load-displacement curves with the motion and pile-up of dislocations are reported as a function of temperature.

Jan 1, 2006

Introduction Gold Mining is an Important Economic Activity in Canada n Total value added during 1990-99 was $15.5 bn n The gold price is an important factor in the value added process n The gold price affects gold mining output, profits, exploration expenditures, employment, etc. Some Factors that Affect the Gold Price n The value of the US Dollar affects the US Dollar price of gold: a weaker US$ correlates with a higher gold price n Supply affects the gold price: the higher the supply on the market each year, the lower the average gold price that year Central Bank Gold Sales n Yearly central bank gold sales add to supply, and affect the price of gold negatively n The negative impact on the price of gold reverberates through the Canadian gold mining industry n Despite the modest amounts, even Bank of Canada gold sales affect the Canadian gold mining industry

May 1, 2003

By J. A. Caceres

Mining planning and mineral processing are almost two unconnected areas. The mining area builds its economical models considering the plant like a constant parameter: a constant throughput, an average recovery and a unitary cost. On the other hand, the mineral processing area assumes a mine plan with grades, ore type, work index, estimating the performances in an independent way. Previous researches have evaluated the advantage for increasing throughput by increasing the liberation size, thus sacrificing recovery. These valuables approaches have left behind the work index factor, critical variable for Recovery-Throughput capacity estimation. This study describes a method combining mineral processing and mining planning. This method incorporates the grinding and flotation performances into the mining economic models optimizing simultaneously the Throughput- Wi(Work index)- Recovery relations with mining sequence, cut-off strategies, and reserve schedules. This method has been used at Andina Mine Chile, showing 18% net present value increasing with minimum investment associated.

May 1, 2003