Search Documents

By L. A. Homeniuk, R. Bonnar

"The Fond-du-Lac uranium deposit is located on the northern rim of the Athabasca Basin. The uranium mineralization is, for the most part, confined to the Athabasca Group, which is underlain by pre-Helikian metamorphic rocks of the Western Craton.The deposit is characterized by a remarkable train of mineralized glacial erratics which led to the original discovery. The mineralization is present as a ""high-grade"" core and a diffuse ""low-grade"" aureole. The ""high-grade"" core occurs as a stockwork of steeply dipping pitchblende veins which strike N 50°E. Hematite, siderite and secondary silicate are also abundant. The ""low-grade"" aureole contains uraniferous goethite, argillaceous material and rare carbon buttons. Recent alteration to coffinite has taken place along the margins of pre-existing ore minerals.The ""high-grade"" core is 390 m long and 10 to 40 m wide, and is surrounded by an irregularly shaped zone of ""low-grade"" mineralization with a similar length and a width of up to 350 m.Comparing the Fond-du-Lac deposit to other unconformity-type deposits, several important differences can be noted:1. Ninety per cent of the ore is above the unconformity, in the Athabasca sandstone.2. The deposit is not associated with underlying graphitic rocks or a major structure.3. The clay-rich alteration zone is not extensive around the Fond-du-Lac deposit.Although there are differences with other Athabasca unconformity-type deposits, the high-grade portion below the unconformity suggests a common origin.The ore deposit is postulated to have been formed from uranium-bearing solutions which entered the stockwork of fractures. Following the reduction in part of these solutions by pre-existing carbonaceous matter and pyrite and/or chemical reaction with pre-existing hematite, deposition continued as a result of decreasing temperature and pressure. Subsequently, minor supergene redistribution of the uranium has taken place."

Jan 1, 1982

By N. D. MacFarlane, D. J. Mossman

"The Nemeiben Lake ultramafic complex, in the Churchill Province of the Canadian Shield in north-central Saskatchewan, is a small I. 6-km circular plug largely composed of high-alumina pyroxene cumulates forming a series of grossly concentric layers of clinopyroxenite, websterite and wehrlite. Minor dunite and gabbro are present in the northwestern part of the pluton.Disseminated primary magmatic pyrrhotite, pentlandite, chalcopyrite, magnetite and chromite occur throughout the intrusion. Sulphides occur in proportions of economic interest in the northern outcrops. A secondary assemblage of fine-grained oxides, sulphides and native metals occurs in serpentinized and uralitized peridotites and pyroxenites. Primary opaque minerals are largely altered to marcasite, violarite and hematite. The ores represent a primary magmatic assemblage extensively modified by metamorphism and, to a lesser extent, by supergene alteration.The complex intruded an Early Aphebian supracrustral succession during the waning stages of the Hudsonian orogeny. The metamorphic peak during Hudsonian time reached middle to upper amphibolite facies, granitized the country rocks and contributed to the partial amphibolitization of the ultramafic pluton.The Nemeiben complex has a number of features in common with the zoned intrusions of southeastern Alaska, including: the diopsidic composition of clinopyroxene, highly magnesian olivines, ubiquitous primary magnetite, relatively high alumina content of clinopyroxenes and the unlikelihood that associated gabbroic rocks are derived from a magma common to the ultramafic rocks. However, at Nemeiben, orthopyroxene occurs as a widespread postcumulus phase and, to a lesser extent, as a cumulus mineral. This fact, together with geochemical data on whole-rock and mineral compositions, indicates a tholeiitic parentage.The nickel-copper deposits of the Nemeiben Lake ultramafic complex are not currently economic, although standard technology for recovery of sulphide minerals in the clinopyroxenite (and websterite) would probably be adequate. Most ore minerals in the altered peridotites belong to the fine-grained secondary assemblage of opaques due to the formation of retrograde hydrous silicates and are probably too fine grained for standard recovery methods."

Jan 1, 1982

By John C. McKay

"The five papers which follow, under the heading of ""Technology Transfer-Universities to Industry"", were originally presented at the 20th Annual CIM Conference of Metallurgists in Hamilton, Ontario. They are a unique group of papers, unique because each paper is concerned with applied research done wholly or partly in a university environment and then translated into industrial practice.Universities can rightly be regarded as one of our nation's greatest resources-a veritable storehouse of knowledge and expertise. Yet, too often, this resource is overlooked or, at best, sparingly used by Canadian industry. Of course, university-based research cannot supplant industry-based research, nor vice versa; each type of research activity has its proper role in the over-all process of technology development.University-based scientists are best equipped to conceptualize, innovate, determine viability of basic premises and to verify these at the bench or small pilot-plant level. Industry based scientists are best equipped to develop ""bench-scale"" innovations into mature manufacturing practices. Thus, university-based scientists and industry-based scientists do not compete with, but rather complement, each other. Active, relevant university research enhances industrial research provided good communication between the two ""solitudes"" is continually nurtured.Good communication between industry and university is a prime objective of CSIRA/ACRIS (Canadian Steel Industry Research Association /Association Canadienne pour la Recherches dans d'Industrie Siderurgique), The directors of CSIRA/ACRIS foster improved communication by making regular visits to universities, by sponsoring projects and by providing lists to professors of uncharted areas where basic research is needed. More can be done to improve communication between industry and university, and it is the intent of the Association to do more.The five papers sponsored by CSIRA/ACRIS are examples of good communication and healthy cooperation. It is interesting to note when reading these papers that the cooperation arose, in each instance, as a result of different circumstances. However, there is a common thread and it is personal acquaintanceship-the university scientist/professor and the industry investigator/manager knew each other prior to the initiation of the project."

Jan 1, 1982

By J. J. Gillman

"The coal deposits from Cape Perce on Cape Breton Island have been known to supply the coal requirements of the people living in or visiting the area for close to 300 years.A major block of coal has been identified off Cape Perce, which has several seams from which coal can be taken. The initial development by the Cape Breton Development Corporation will be in the Harbour Seam and constitutes the Donkin-Morien Development Project.The CBDC's confidence in this indicated resource is based on its knowledge of the Sydney Coal Field and from boreholes driven into the block during the summers of1977, 78 and 79. In 1980, further geological data were gathered from surface drilling and an intermediate-depth high-resolution seismic survey. The surface facilities for the Donkin-Morien Development Project will be located on the northern half of the cape, with access declines extending 3.9 km in a north-northeasterly direction to the Donkin block of coal reserves. The development has the potential of supplying all the coal needed f or the future electrical power generation requirements of Nova Scotia for many years to come.The planned mine, for which a project definition study has recently been completed, will have a production rate in excess of 3 million tonnes per year.IntroductionAt the Second CIM District 1 Meeting held in Halifax in October 1980, a background paper on Phase II of the Donkin-Morien Development Project was presented. The project involves a 3.2-million-tonne, saleable, underground coal mine. At that time, the chronological sequence of events had unfolded, starting with the initial boreholes through to the feasibility study, and on through site clearing and site preparation. This led to engineering design contracts for the portals and the two tunnels to be driven to intersect with the Harbour Seam close to 4 km from their entry point."

Jan 1, 1982

By T. Alan O'Hara

"The decision to invest capital in developing a mine and constructing a mineral processing plant and services is usually made after a feasibility study shows 'that the estimated future cash flow from mine operations will yield an adequate return on the estimated capital expenditures.The actual return on investment may differ substantially from that estimated in the feasibility study, because of the probabilities of errors in estimating capital costs, ore reserves, operating costs, mineral revenue and operating productivity. This paper outlines the R.S.S. (root sum of squares) risk analysis procedure of computing the overall probability of the actual project D.C.F. (rate of discounted cash flow), differing from that estimated in the feasibility study.Variation in Project D.C.F.It is assumed that a feasibility study of the project has been completed which has defined the estimated values for all the project parameters, such as ore reserve tons and grade, capital cost, concentrate recovery, metal revenue, daily milling capacity and operating costs.The financial analysis of the mining project will have determined that the cumulative cash flow will yield an expected D.C.F. on the capital cost if all project parameters attain the estimated values. If, however, the actual value of any parameter varies from that estimated, the actual project D.C.F. will vary from the estimated D.C.F. Risk analysis methods attempt to determine the overall effect of probable variations in the estimated values of all project parameters on the D.C.F. of the mining project. This overall effect is expressed as a probability profile, which shows the likelihood of actual D.C.F. values greater or less than that estimated.Thus, a completed risk analysis of a mine project, with an expected D.C.F. of 15.51%, would display the characteristics shown in the preceding diagram."

Jan 1, 1982

By W. B. Morrey

"In recent years, the major effort in detonator development has been concentrated on ""non-electric"" systems. Existing types all involve some form of explosive reaction to transfer ignition energy from outside the borehole to the pyrotechnic delay element contained within the detonator. These may be based on low-energy detonating cords having grained or plasticized explosive cores, shock tube energy transmission principals and explosive gas ignition systems. Each has properties of internal and external effects not present in electric conductors.The MAGNADET System introduces transformer coupling into electric blasting circuits. Safety features with respect to current leakage, stray currents of AC or DC source, electrostatic energy and radio-frequency radiation are comparable to ""non-electric"" systems, with advantages in simplicity, speed of hook-up and range of application.The transformer device used is a small ferrite ring or toroid which is an integral part of each specialized detonator. The detonator legwires form the secondary side of the transformer winding. The primary side is a single wire loop common to all units within the circuit. Power is supplied from a frequency-tuned portable exploder with unique circuit-sensing features.The MAGNADET System is expected to have particular application to shaft sinking, raising and tunnelling where the protective features as well as speed and efficiency are critical factors. Applications of the 'MAGNA' booster in quarries, open pits and longhole deck charges offer control over vibration problems and elimination of surface noise.IntroductionFor many years, electric detonators and electric blasting systems dominated surface and underground applications where controlled delay times were required. Control over the instant of detonation by blasting machines or power-line switches is the major safety feature.Electrical energy exists in many forms. It may originate from many sources. Electrical energy can be difficult to contain. It may enter or escape through a variety of conductive paths. It may fluctuate, concentrate or dissipate to pose a most elusive potential hazard."

Jan 1, 1982

By J. R. Pronovost, P. M. Tiley, D. W. Watts

"In 1980, J.S. Redpath Limited were retained by Dickenson Mines Limited to increase hoisting capacity from 700 to 1000 tons per day. The hoisting capacity of the present skip-over-cage system could not be increased significantly through design modifications. The other constraint was a minimum of disruption to the current production. The Dickenson shaft was a three-compartment shaft from surface to the 8th level and four compartments before the 8th to the 23rd level. The solution to the problem was to remove the services from the shaft man-way compartment from the 8th level to surf ace by drilling a borehole close to the shaft and rerouting those services through the borehole to the 8th level. A service compartment would then be available from surf ace to the 23rd level.By providing a service hoist in this compartment, the skip hoist would then be free to produce the 1000-tons/day required production. This paper will describe the search for the required hoist and the friction hoist selected for the project, and trace the design modifications required to modify the hoist to suit the Dickenson application and satisfy the Department of Labour safety requirements.The paper has been co-authored by J.S. Redpath Limited and C.L. Tiley Associates, who participated in the design changes and eventual commissioning of the hoist.IntroductionIn the earl y part of 1980, J.S. Redpath Limited conducted an engineering study on the Dickenson Mines Limited No. 1 Shaft materials handling system. The object of the engineering study was to investigate the possibility of increasing the tonnage hoisted from the No. 1 Shaft complex by adding a service cage compartment and service hoist. This would permit utilization of the existing hoisting plant solely for production hoi sting. A further consideration of the engineering study was that any alterations had to be accomplished with little, or no, interruption to production."

Jan 1, 1982

By G. Kollberg

"IntroductionThe SALA Caravan Mill system represents a proven concept for the design and operation of mobile and semi-mobile ore dressing plants.The Caravan Mill has been developed to meet the demand for a flexible processing plant to be used for small and medium-sized orebodies or for pilot investigations of deposits directly at the mine site e •The first Caravan Mill installation was put into operation in 1970 and a number of plants have been delivered world-wide since then.The Caravan Mill system has great flexibility both in capacity, ranging from 50 to 1000 tons per day, and in process combinations. The process modules available are:• crushing by jaw and cone crushers;• pre-concentration by the Dyna Whirl Pool dense media system;• grinding by wet rod or ball mills;• separation by gravity, magnetic, flotation or leaching-CVP adsorption methods;• dewatering by lamella or conventional thickeners and vacuum filters.To form complete plants, auxiliary equipment is also available, such as:• bins, feeders and conveying systems;• power generator units;• water tank and pump for process water;• interconnecting piping and cables;• erection and service tool kits;• set of spare and wear parts.For mine sites with rainy or winter conditions, a plastic tent with air heater can be supplied to cover the ore dressing equipment. Each module is workshop assembled complete with slurry pumps, internal pipe work, electric wiring with plug-in connections, hoses, etc., all arranged for quick and simple connection between the units. Before delivery, each unit is tested in the workshop."

Jan 1, 1982

By J. A. Stewart

"A common problem in the mining industry involves the overloading of established conveyor systems. This overloading can have a number of causes, such as new production technology or a changing market condition which increases demand. An overloaded system usually spells disaster and leads to clean-up problems, equipment failures and lost production. The Cape Breton Development Corporation's Lingan Mine had a serious overloading situation on its underground coal clearance system, and equipment was being damaged and production was being lost. It was rectified, in part, by increasing the coal clearance capacity through the use of booster conveyors. This paper discusses the problems which led to this situation, the booster concept and the installation of the first unit at the Lingan Mine.IntroductionThe Lingan Mine is a submarine coal mining operation with an annual production of 1.5 million tonnes from three advancing longwalls. Coal is conveyed 3400m up a 13% slope to the surface. Designed and installed in the early 1970s, the system's 820-tonne/hour design initially proved adequate; however, by the late 1970sthe system was handling surge loads of 1640 tonnes per hour due to the introduction of new face equipment.The coal clearance system consisted of three 485-Kw, two 210-Kw and one 105-Kw conveyors. Each conveyor was designed for 820 tonnes per hour using 1050-mm, Type 10 belt with a 35-degree troughing profile.There were many effects of the overloading on the system:• Loading beyond the physical capacity of the belt resulted in spillage along the conveyor, which increased operational and maintenance costs.• Overloading of the drive components resulted in premature equipment failures.• Spillage at the drive pulley often resulted in damage to the belt and pulley lagging and, under extreme conditions, the conveyor would require partial unloading before it would operate. This was a particular problem under wet conditions because the 485-Kw conveyor drives were fitted with single-drive drums."

Jan 1, 1982

By W. H. Stheeman

"The high rock pressures at the deeper levels of the Tsumeb Mine have necessitated the changing of the mining methods and the introduction of cable bolts. After two rockfalls in the cable-bolted stopes, the mechanics of cable bolting were investigated. Practical methods were developed to find the best grout mixtures, the bond stresses between cables and cement, the bond stresses between rock and cement and the load on the cable bolts, which was mathematically calculated from data observed underground. The design of the cable bolt support system as used at the Tsumeb Mine is explained. GeneralThe Tsumeb Mine is in northern South West Africa/Namibia, approximately 400 km by road from the capital city, Windhoek, at an elevation of 1300 m above sea level. Mining operations in Tsumeb were started in 1905 by the Otavi Minen und Eisenbahn Gesellschaft and continued, with an interruption during the Depre ssion, until 1940, when the mine was closed and taken over by the Custodian of Enemy Property. The present owner, Tsumeb Corporation Limited, obtained the mine in 1947 and restarted the underground mining operations in 1949 after the mine was dewatered. Currently, the stoping operations are between 26 Level (840 m below surface) and 38 Level (1260 m below surface). In addition, the mine is an important silver producer and has produced 670,100 kg of silver since 1947."

Jan 1, 1982

By B. Lewis

Paper did not make deadline for printing

Jan 1, 1982

By R. E. Jones

"INTRODUCTIONCominco Limited, one of the free world's largest producers of lead and zinc having majority ownership in Pine Point Mines Ltd., operates a mining and concentrating complex on the south shore of Great Slave Lake in the Northwest Territories. The mine was developed in 1963-64 and commenced operation late in 1964 with the direct shipping of high grade ore. The concentrator started production in November 1965 at a design throughput rate of 5,000 T.P.D.In 1968, the Company acquired the mining rights to a large ore body located to the east of the Pine Point claims and subsequently an expansion program at the concentrator raised the throughput rate to 8,000 T.P.D. The expansion included a third grinding circuit and additional flotation capacity. The flotation capacity took the form of a completely separate circuit from the existing flotation plant. In 1972, the zinc flotation circuits were modified to include two additional stages of cleaning. This change concluded the ""Pre-Consolidation Flotation"" circuit at Pine Point.In considering these modernization programs of the flotation section of the concentrator, the philosophy was to utilize the largest available machine having proven and modern technological changes. With the advent of the large capacity machines available in the late 1970's, it was considered a suitable time to revamp the entire flotation circuit at Pine Point in 1979. The Circuit Consolidation Project was developed to meet this requirement."

Jan 1, 1982

By T. P. Lim, N. K. Davé

"A modified accumulator method was devised to measure surface radon flux from porous media. It consists of a collector hood type of accumulator with a homogenizer pump and a pressure balancer. The latter was used to compensate any pressure changes produced during sample withdrawal and hence eliminate additional radon transport from the media. Errors resulting from radon back diffusion due to decreasing concentration gradient with time across the interface were also eliminated by measuring radon concentrations in the accumulator for two different periods of time and calculating the true radon flux, J(o), from the solution of a time-dependent radon transport equation in the absence of any pressure and temperature gradients.Core samples from the observation site were also withdrawn for laboratory determination of porosity, moisture content, bulk and grain densities, Ra-226 source concentration and the fraction of Rn-222 produced in the void volume. The data were used to calculate the radon diffusion coefficient for the media.Using the present method, the true value of surface radon flux for an abandoned uranium tailings pile was obtained as J(o) = 2020.2 mBq/m2/sec (54.6 pCi/m2/sec) compared to the value J = 1406.0 mBq/m2/sec (38.0 pCi/m2/sec) obtained by the conventional method. The bulk diffusion coefficient of radon for the media was obtained as 1.2 x 10-7 m2/sec.IntroductionRadon-222 (hereafter called radon) released from uranium mill tailings is a continuous source of environment radioactivity in terms of its transport as an airborne gas and its decay products. The particulate daughter products readily attach to aerosols or dust particles and can further be transported by various other environmental pathways. Typical radon release rates from existing tailings piles vary between 740 and 14,800 mBq/m2/sec (20-400 pCilm2/sec), depending on the nature of the tailings material, moisture content, etc. The United States Nuclear Regulatory Commission (NRC) is proposing radon release rates of 74 mBq/m2/sec (2 pCi/m2/sec) above that of background."

Jan 1, 1982

By John Clancy, Andrew J. Freyman

"Trends in world coal markets indicate that the next twenty years could be a period of intensive development for British Columbia's coal resource. This paper examines demand projections for metallurgical, thermal and chemical feedstock coals, with particular reference to domestic and Pacific Rim markets. Supply possibilities, from the point of view of British Columbia's competitive position, are explored, with emphasis on the interaction of such factors as capital, labour, port and transportation requirements.The paper concludes with an examination of British Columbia's strategies in light of the foregoing, and comments on the government's role in ensuring that development of the coal resource be attained in a manner consistent with over-all provincial goals and objectives.IntroductionFor the purposes of this paper the Pacific Rim is defined as including, in addition to Canada, the following: Japan, Korea, the People 's Republic of China, Hong Kong, Taiwan, the countries of the Indonesian Archipelago, Australia, New Zealand and the Pacific-bordering countries of South America and Mexico. The United States has been excluded in this definition in order to better illustrate the economic growth potential for British Columbia coal in the Pacific Rim economies.In the past decade, the Pacific Rim economies have grown faster than most other economies in the rest of the world; economic growth rates of 10 per cent were common in the region prior to the 1974 slowdown and the average rate of economic expansion in the mid-1970s has exceeded 6 per cent. Rapid expansion of international trade in the region has been a major stimulus in this process. By 1979, Pacific Rim two-way trade has reached an estimated $550 billion-about 20 per cent of world trade."

Jan 1, 1982

By Erwin L. Zodrow

"The neglect of including the toxic metal mercury in the list of escaping elements (Zodrow, CIM Bulletin, September 1982, pp. 138-140) was pointed out to the author in a private letter by J.E. Rehder, dated September 21, 1982. I welcome this opportunity to present my preliminary mercury research data based on coal investigations supported by N.S.E.R.C and the University College.As mercury is a volatile element and liquid at room temperature, special analytical techniques are required to determine concentrations in whole coal. In the investigation, the coal is analyzed by flameless atomic absorption with a lower detection limit of approximately 10 parts per billion, which, however, is a function of the ash contents of the coals (personal communication, J.L. Brooker, XRAL, 1981).Coal seams of the Sydney Coalfield studied so far include: the Point Aconi, a thin shaly coal, the Upper Bonar, an overrider of the Harbour seam, and the Harbour, Shoemaker and McAulay seams, all of which are shown in stratigraphic succession in Figure 1. The seams have been channel-sampled taking 15-cm coal intervals as one sample for analysis. One channel sample has been investigated from each of the seams listed (two channels were taken from the Point Aconi seam), resulting in 38 samples. Table 1 shows the results, which include mercury contents, ash and total sulphur per sample interval. Figure 2 is a frequency distribution of the 38 determinations."

Jan 1, 1982

By K. Wyper

"Gulf Minerals (Canada) Limited' s Rabbit Lake Uranium Operation is located in the northern portion of Saskatchewan, 198 miles southeast of Uranium City and 134 miles northwest of Lynn Lake Manitoba.This paper describes flow sheet changes to solve operating problems and briefly describes future changes to accommodate the new ""B"" Zone ore.The Rabbit Lake mill was designed to process 1600 dry tons per day of uranium ore, with an average grade of 0.370 percent u3o8. In 1981, the mill processed 2040 tons per day at a grade of 0.231 percent u3o8 . The process modifications and flow sheet changes that allowed this increase in tonnage will be discussed in relative chronological order. Mill feed was introduced on June 10, 1975, the original equipment consisted of an Ingersoll Rand hydraulic breaker mounted over a 24"" square grizzly. The - 24"" ore was fed to a 2011 X 6"" seflli autogenous grate discharge mill close circuited with 20"" cyclones, the mill discharge was screened on a tyler double deck screen with the undersize (8 rnesh) reporting to the cyclones, the screen oversize was returned by conveyor belt to the mill feed chute.The cyclone overflow (28 mesh) was thickened in a 100' diameter thickener to obtain 55 percent solids for the leach circuit.The leach circuit consisted of two slurry holding tanks and five leach tanks."

Jan 1, 1982

By Donald C. Craighead

"Overland conveyor systems to transport bulk materials from mines to processing plants or load-out stations have to be seriously considered as the viable alternative to truck and train haulage systems. With the ever-increasing price of diesel fuel, conveyors with their electrical drives generally prove to be the least costly when operating and maintenance expenses are analyzed for the life of the installation.IntroductionOverland conveyor systems are now considered as one of the viable alternatives which should be closely investigated when a mining company and its engineers initiate studies on methods of transporting raw materials from a mine to a processing plant or rail load-out station.This paper will generalize the overland conveyor and compare it with alternative handling systems. Each installation must be carefully studied to determine the best route, type of foundations river crossings; amount of excavation work for cut and fill, maintenance roads, etc. No two locations are the same nor are the principles of operation of an overland conveyor the same as those of a normal plant or mine belt conveyor. The proper time and effort must be put into the study of the system to evaluate the costs for comparison with other systems.The length of the overland conveyor depends on the layout of the mine and plant and the topography of the terrain between the terminals. Individual lengths may be up to 20 km, and a series of conveyors may extend 100 km or more.Advantages of Overland ConveyorsThe main advantage of overland conveyors is the low operating and maintenance costs which will be realized over its years of operation. Although truck haulage probably will permit lower capital investment during the initial phases of the mine development when the annual capacities have not developed to the design level, their operating and maintenance costs will be considerably higher. When evaluating the total costs per ton of material to be handled during the expected life of the operation and the projected increases for diesel fuel versus electricity, overland conveyor systems will generally prove to be economically more viable."

Jan 1, 1982

By Erwin L. Zodrow

"For 25 chemical elements in electrostatically precipitated fly ash (Lingan coal-fired power station), concentration changes are studied as a function of increasing proportions of fines (ash particle diameter less than 45 micrometres). Elements that are involved when concentrations increase as the proportions of fines increase are likely to escape into the atmosphere. These are Th, U, As, S, P, Sb, Na, Ag, Zn, Pb, Ni, Ba, Sc, AI, Mo (and Bi, Ge, Ga, F and Li), i.e., more or less highly volatilized elements. Of the less volatilized metals such as Fe, Ca, Cu, Ti, K, Co, Mn (and lanthanides), certain portions presumably also escape as stack emissions. Diadochy and spinel formation in bottom slag is presented as an emission-reducing agent for certain metals.IntroductionThe Lingan coal-fired power generation plant, owned and operated by the Nova Scotia Power Corporation, produces annually about 140,000 metric tons of ash (the residual mineral content after burning coal). The tonnage is based on a 15 per cent average ash content of Cape Breton coal.For purposes of this report, samples of the hard, fused slag (bottom slag) that is accumulated at bottoms of boilers, and electrostatically precipitated fly ash (ep ash), were collected and investigated. Bottom slag is a minor component of the produced ashes.The ashes were surveyed and the presence of over 75 major, minor and trace elements is reported. From this survey, 25 elements were selected to establish elemental enrichment/depletion trends when the proportions of the less than 45 micrometre <45µm) fractions in ep ashes increase. The results are significant in that, taking the case of elemental enrichment, the elements involved are likely to escape into the atmosphere, i.e, highly volatilized elements. Depletion trends for elements are presumably associated with less volatilized elements during coal-firing. Quantification of the emission of atmospheric pollutants is not considered part of this work. ""Igneous"" minerals generated during coal combustion include spinels (found mainly in the bottom slag), quartz, glass and mullite."

Jan 1, 1982

By John C. Loretto

"The paper identifies two of the main problems encountered in recent hydrometallurgical plants for the recovery of gold and silver: firstly, the plant recovery is lower than anticipated from the testwork; secondly, the metallurgical accounting figures cannot be reconciled.The principal reasons for the plant recovery being lower than the testwork are discussed, together with solutions that can minimize these problems both during the design stage and during the plant operation after the problems have manifest themselves.The reasons for the difficulties in metallurgical accounting are analyzed by reviewing the various components of the plant figures. Recommended solutions are given for minimizing this problem and the realities of obtaining accurate figures are discussed.IntroductionThe start-up over the last few years of new hydrometallurgical plants for the recovery of gold and silver has brought to the surface again a number of problems. Most of the problems have existed for some time and they manifest themselves mainly in two ways. Firstly, the plant results do not agree with the metallurgical testwork figures; secondly, the metallurgical accounting figures do not balance.Metallurgical TestworkThe plant results not agreeing with testwork figures are mainly due to:a) testwork samples not representative of the eventual plant feed;b) misinterpretation or misunderstanding of testwork ;c) plant losses;d) plant design not allowing testwork results to be achieved;e) operating deficiencies."

Jan 1, 1982

By R. Ricketts, D. G. Vanderveer, F. Kirby

"A program of mapping, sampling and testing to determine the potential of the aggregate resources throughout Newfoundland and Labrador was commenced in 1978. A 6-km-wide corridor parallel to all transportation routes was selected as the study area.The study consisted of a preliminary surficial interpretation followed by field mapping and sampling. Granular resources were sampled at a 500-m interval and non-granular materials were sampled at a 1.5- to 2-km interval. Data were gathered on landforms and stratigraphy as well as a field description of the sample and deposit types. Particle-size and lithologic analyses of the samples were also conducted.The locations of samples and deposits were mapped on 1:50,000 topographic base maps and summarized for publication at a 1:250,000 scale. Surficial geology maps were produced at a 1:50,000 scale. A computer program is being developed for the search and retrieval of field data.The first phase of the Inventory of Aggregate Resources program is nearing completion and to date has collected information on approximately 9,500 samples throughout Newfoundland and Labrador. This data will be used to provide f or the effective management of these vital non-renewable aggregate resources.The mineral aggregate industry in Newfoundland and Labrador is very competitive, but undercapitalized when compared to other provinces. The demand for aggregates is forecasted to increase to in excess of23 million tons per annum by the year 2002.In terms of over-all mineral production, the extraction of sand, gravel and stone has a significant impact when compared to other minerals in terms of value and tonnage produced.IntroductionThe province of Newfoundland has approximately 18,000 km of coastline. A large proportion of the population lives in coastal communities where, traditionally, beaches have been a major source of construction materials. Beaches have, therefore, often been subjected to overutilization, resulting in erosion of back beach areas or adjacent headlands."

Jan 1, 1982