Search Documents

By G. L. Neumann

Owing to the need for additional sources of supply of both zinc and lead following World War II, the Bureau of Mines investigated many abandoned lead-zinc mines in the eastern United States. A series of shallow veins in south-western St. Lawrence County has long been a subject of speculation. These veins, which average about 4 feet in width and cut across the bedding of the country rock at right angles, are filled with calcite-carrying galena and sphalerite. The deposits have been worked sporadically during the last 115 years. From 1837 to 1852 the Coal Hill, the North, and the Victoria mines near the village of Rossie were at their peak of activity. Other calcite veins were prospected and a small production was realized. The Bureau of Mines began diamond drilling May 1, 1950, under the general supervision of McHenry Mosier, chief, Mining Branch, Bureau of Mines, Region VIII, and under the immediate supervision of the author) who was project engineer, following the preliminary examination by Robert S. Sanford. A total of 3,870.2 feet was drilled in 18 holes on four of the numerous deposits scattered over Macomb and Rossie townships. Drilling was completed September 21, 1950.

Jan 1, 1952

By S. H. Ash

THE information obtained by examining and analyzing the core drillings from 15 diamond-drill holes shows that with the proper equipment little difficulty should be experienced while sinking the shafts at the 15 selected sites. Although a number of holes penetrated formations containing a high percentage of silica,, the health hazard from dust can be removed by using proper dust-control equipment. Methane was detected in small amounts in only one (hole 5) of the boreholes. The methane hazard should present no difficulty if adequate ventilation is employed while sinking the shafts.

Jan 1, 1952

By H. W. Wainwright

.1. The purification pilot plant and the equipment, solution, and gas cycle used for removing hydrogen sulfide and carbon dioxide are described. 2. As sulfur recovery is necessary in any large Fischer-Tropsch plant, pilot-plant runs were made at 300 p.s.i.g. to study the efficiency of tri-ethanolamine solutions in removing selectively hydrogen sulfide from gases containing varying amounts of carbon dioxide. 3. Aqueous solutions of TEA of 20, 30; 35, and 50 percent were investi¬gated. Data indicate that 30 to 35 percent is the optimum concentration if both selectivity and economy are considered. Slightly better selectivity is obtained with the.20 percent solution, but steam consumption is greater owing to the higher solution rates. Results from our pilot plant runs indicate that a 50 percent solution not only produces an acid gas of lower hydrogen sulfide content but also requires high solution rates to effect hydrogen sulfide purification. 4. Data from 37 runs using TEA are presented in tabular form. In addition, the data are correlated and presented in three sets of curves. By using these curves, it is possible to calculate the compositions of the purified and acid gases for various raw gas mixtures. 5. In cooperation with the Southern Natural Gas Co., investigations were carried out at 300 p.s.i.g. on the simultaneous removal of hydrogen sulfide and carbon dioxide, from gases using various concentrations of diethanolamine. 6. Data from 17 runs employing 20, 30, and 40 percent DEA are reported in both tabular and graphic form. 7. A comparison of the data from one DEA run made at 200 p.s.i.g. with those from the runs operating at 30O p.s.i.g. shows float the absorption capacity of the solution, and, hence, the steam requirements per gallon are about the sage for both pressures. .The only real advantage of the higher pressure is the additional volume of gas that can be treated. 8. The quantity of steam needed to reactivate fouled TEA and DEA solutions increased as the reactivator pressure was increased about 1,0 to 1.1 pounds of steam was required for each gallon of circulating solution when the reactivator was operated at 5 p.s.i.g. 9. A curve is included that shows the effect of the hydrogen sulfide con-centration in a lean 35 percent TEA solution on the hydrogen sulfide content of the purified gas and on steam consumption for reactivation. 10. Both TEA and DEA reduced the organic sulfur content of the raw synthesis gas considerably. Analyses of the lean amine solutions showed a gradual build up of sulfur compounds, indicating that the compounds formed by the amines and organic sulfur do not break down under the ordinary operating conditions of the reactivator. 11. Considerable operating difficulty was encountered in the pilot plant owing to foaming of the amine solutions. Laboratory experiments in which the effectiveness of certain antifoam agents was studied showed Alkaterge C to be most promising for the particular conditions studied.

Jan 1, 1952

By H. L. Gilbert

Improvements in production of high-purity chromium metal by magnesium reduction of anhydrous chlorides and by hydrogen treatment of electrolytic chromium are reported. Hydrogen-treated chromium has been arc-melted, and the arc-melted material has been successfully forged, rolled, and swaged. The material also has been forged at liquid-air temperatures. X-ray and metallographic studies indicate the recrystallization temperature of rolled chromium sheet to be about 750° C. Preliminary investigation of hot-bending characteristics of rolled chromium sheet shows the minimum bending temperature to be about 325° C. The heat resistance of chromium has been investigated.

Jan 1, 1952

By A. L. Engel

This report is a compilation of results of preliminary tests on scheelite (tungsten) ores and tailings. These investigations were made to assist in establishing satisfactory treatment methods for small-scale concentrator operations, or to indicate a. method for conserving previously lost mineral values in old tailings, if possible. A discussion of test procedures is included, as it was felt that this would add to understanding the results reported under the several projects. The treatment of scheelite ores has become more or less standardized. Important differences occur in textures of ores from various mining districts. However, and this must be considered when planning ore-dressing operations. In most of the present investigations, only a limited amount of work was done, usually just enough to answer a specific question in regard to a particular ore or concerning local conditions. Two methods of treatment included gravity concentration, magnetic separation, and flotation.

Jan 1, 1952

By William L. Crentz

Floyd County, KY., contains sizable deposits of high volatile bituminous coal. Some of the coals have been blended with higher-rank coals and used in the manufacture of high-quality metallurgical coke. The Upper Elkhorn No. 3, Upper Elkhorn No. 2, and Upper Elkhorn No. 1 beds produce the bulk of the present output in the county and contain the main known reserves of coal. Little information is available concerning the quality and extent of the deposits underlying the Upper Elkhorn No. 1 bed, although small operations in the past have worked a bed that is reported to be; the Lower Elkhorn. Undoubtedly, these lower beds occur in Floyd County, but depth Will preclude their development into a major source of fuel as long as large deposits of more-accessible coal are available. More is known of the occurrence of the beds above the Upper Elkhorn No. 3 owing to sporadic mining ventures in the upper measures. Many of the coal samples from beds above the Upper Elkhown No. 3. were collected in mines that had been abandoned. Almost all of the present production of Floyd County coal is taken from the Upper Elkhorn beds, and it is unlikely that their dominant position as coal producers will be challenged in the near future. Table 1 shows the coal production of the county by beds, during 1950.

Jan 1, 1952

By G. L. Humphrey

Although silicon carbide has been an important manufacture refractory for many years, knowledge of its thermodynamic values has been seriously lacking. In fact, some of the very properties that make it a useful substance, particularly chemical inertness, obstruct determination of its heats of formation and reaction. This paper reports the results of new measurements of the heats of combustion and formation, low-temperature heat capacity, entropy at 298.16°K., and heat-content and entropy increments between 298° and l,800°K. Two varieties of silicon carbide were studied -the common, hexagonal (type II) and cubic. The data are combined to obtain heat and free-energy-of-formation functions, which are given in tabular form. It is shown that the cubic variety is the more stable at temperatures to at least 1,800°K but, because of the inherent difficulties and errors in the heat-of-formation determinations at 298°K, it was not found possible to specify the free-energy difference accurately. The mechanism of silicon carbide formation from silica and carbon is not known and is not ascertainable from thermodynamic data. It appears improbable, however, that it can be a single-step reaction. Some reactions involving silicon monoxide gas and metallic Silicon, as possible intermediates in silicon carbide formation, are considered and shown to be thermodynamically feasible.

Jan 1, 1952

By G. L. Neumann

The Guymard mine in Orange County, N. Y., is reported to have been discovered in 1862 and mined until 1876, producing 10,000 tons of lead and zinc ore. The property was examined by an engineer of the Bureau of Mines in 1948. Development work was done by the Bureau in April and May 1949 and March 1950. During these two periods four drill holes totaling 2,090 feet were completed. The mineralized sections of the core were sampled and assayed.

Jan 1, 1952

By James J. Dowd

The investigation to evaluate the reserves of coking coal is being made by the Bureau of Mines in three parts: (1) To estimate known measured and indicated recoverable reserves of all coking coal; (2) to upgrade marginal coals through effective preparation; and (3) to study the carbonizing properties of coal and coal blends not now widely used for metallurgical coke making. This is the tenth of a series of reports giving the results of studies by counties under part (1) of the investigation. (See appendix.) This report covers Knott County, Ky., which comprises parts of the Salyersville, Prestonsburg, Troublesome, Hindman, Pikeville, Cornettsville, and Whitesburg quadrangles. (See fig. 1.) A base map for each bed in each quadrangle was made to the scale 1 inch equals 1,200 feet. Maps of mines, locations of drill holes, bed and total coal thicknesses, and the outcrop of the bed were plotted on the maps. With all available data plotted, isopach lines were drawn to limit areas of known unmined reserves in beds up to 14 inches thick, 14 to 28 inches thick, 28 to 42 inches thick, and over 42 inches thick. These areas of coal reserves also were divided into "measured" and "indicated" categories. All areas in each thickness range and category, mined-out areas, areas excluded from the estimate but which may contain reserves based only on geologic inference, and areas outside of the outcrop were measured by planimeter on the base maps. Estimates of total reserves 14 inches and more thick and maps for individual beds were prepared from these data.

Jan 1, 1952

By John W. Taber

Discovery of these unusual fluorite deposits was brought to the attention of the Bureau of Mines late in 1951, shortly after the first locations were made. A brief investigation of the deposits by the Bureau revealed seven principal outcrops of fluorite in two areas. The smallest outcrop continuously exposes massive fluorite over an area 25 by 55 feet; the largest outcrop is a similar exposure 180 by 240 feet. The deposits appear to be sharp-walled, low-angle-, tabular ore bodies in granite and are at least 10 feet thick. The Bureau investigation of the deposits included bulldozer strip-trenching, drilling and blasting rock cuts, and channel sampling across three of the largest outcrops. This sampling indicated an average grade of 97.2 percent CaF2 and 1.44 percent SiO2. Preliminary metallurgical tests on the ore indicate that it can be concentrated to acid-grade specifications by simple gravity methods. One laboratory test recovered 78.4 percent of the fluorite in a product containing 98.7 percent CaF2, 0.25 percent SiO2, and 0.10 percent Fe2O3.

Jan 1, 1952

By R. V. Holmes

The properties of the Colorado Copper Co. in Sinbad Valley, Mesa and Montrose Counties, Colo., were rehabilitated and sampled by the Bureau of Mines in October, November, and December 1942. The several deposits were reexamined in March and April 1945 to obtain information disclosed by company work after December 1942. The development program included surface trenching, rehabilitation of several edits, and channel sampling of the exposures. Assay determinations wore made on 204 samples from the surface and underground workings. The results are given in the appendix. Several copper deposits in the Sinbad Valley area are similar in origin. The host rocks are sedimentary and mice in age from Pennsylvanian to Cretaceous. The Colorado No. 3 deposit occurs in the Cutler formation, which consists of many small lenses of conglomerate, sandstone, and shale. Mineralization is closely associated with faulting. On the Pyramid group the enrichment occurs in a zone of fracturing and jointing end also spreads into the adjoining sandstone. The ore deposition on the Copper Rivet claim is associated with a fault zone and is confined to en area above the contact of the Dolores-Wingate formations. Mineral deposits on the Sinbad claims occur at intersections of faults with blue-gray Pennsylvania limestone. Copper enrichment occurs along faults and as replacement of the surrounding limestone. Metallurgical tests indicate that ores from the Colorado No. 3 and Pyramid claims can be treated successfully by leaching with sulfuric acid. This method cannot be applied to ores from the Copper Rivet or Sinbad deposits because of high calcite content. Flotation tests at Boulder City, Nev., showed a recovery of less than 60 percent with a 14.24 percent copper concentrate.

Jan 1, 1952

By K. C. Dean

During the course of the investigation of manganese mineral occurrences in the western United States, the Bureau of Mines collected several lots of ore' from properties in the vicinity of Winkelman, Ariz. As none of the ores would be marketable directly, an investigation was made to determine their amenability to concentration by ore dressing. The Geronimo group of claims is in Pinal County, 8 miles west of Winkelman, Ariz. The manganese oxides occur as cementing material in ore zones of conglomerate. Representative samples of a 2-ton lot of ore cut from outcrops of two lenticular deposits were laboratory-tested. Two 1-ton samples from the Benningfield property were similar in physical characteristics but differed in grade. This claim is 11-1/2 miles south of Winkelman and about 1 mile west of the San Pedro River on the south side of Putman, Wash. The manganese minerals occurred as nodules and lenses, replacing limestone, in a capping over a dark, igneous dike. The North Star group consists of five claims on the west side of the San Pedro River 14 miles south of Winkelman. The ore consists of a low-grade, manganese oxide-calcite occurrence interspersed with stringers of higher-grade material and is present as filling in a fissure zone in porphyry. Two samples were obtained by the examining engineer; one sample represented run-of-mine material, the other represented ore from the vein that could be hand-sorted or selectively mined.

Jan 1, 1952

By M. A. Cook

Crude titanium metal, produced by the reduction of titanium tetrachloride with magnesium, is contaminated with some excess magnesium end adhering magnesium chloride when it is removed from the reaction pot. The method of vacuum 'purification is described in which the crude mixture is heated in a vacuum at a temperature of about 1,700° F. and the magnesium metal and chloride are volatilized away from the titanium, leaving it practically magnesium-free in a sponge-metal form. The pilot-plant equipment is described in detail, together with the technique of operation and methods of sponge recovery. Operating data is given, which compares ten 24- to 30-hour heats with ton 48-hour heats, and finally, power and labor requirements are discussed. Vacuum purification of raw titanium produced by the Kroll process has boon employed for treating of several tons of raw titanium with results for superior to those achieved by the method of leaching and grinding. The operations described, while on but little more than pilot-plant scale, indicate commercial feasibility of the process, even though it is a batch-typo operation. All equipment is either of standard manufacture or can be readily fabricated from standard materials, and operation of the units can be satisfactorily maintained by semiskilled labor.

Jan 1, 1952

By M. E. Volin

The tungsten potentialities of the Combination mine were examined by a mining engineer of the Bureau of Mines in 1947. A report based upon his personal knowledge of the mine and the results of the examination contained recommendations for further investigation. This report presents factual data from Bureau of Mines field investigations begun in August 1947 and continued until December 1948, except for a 5-month recess during the first winter. The Combinat.ion mining property of 52 patented claims and 15 patented mill sites is in the Black Pine mining district, Granite County, Mont., 11 miles northwest of Philipsburg. The altitude in the mine vicinity is approximately 6,500 feet.

Jan 1, 1952

By J. B. Zadra

After the discovery of the rare-earth mineral deposit in the Clark Mountain area near Mountain Pass, San Bernardino County, Calif., two samples wore obtained through the Mining Division of the Bureau of Mines for investigation of possible method of concentration. Three other samples were received later from different locations in the same area. The rare-earth mineral in this ore had been identified by E. T. Schonk as bastnaesite, a fluocarbonate of the rare-earth metals containing cerium, lanthanum, praseodymium, thorium, uranium, etc. Associated with the bastnaesite were barite, silica, and some calcite. The bastnaesite contained a small amount of iron as a coloration and some manganese. Twenty to fifty percent of the weight of the samples studied was bastnaesite, or ten to twenty-five percent total rare-earth oxides; about half was cerium oxide. Apparently, none of this mineral occurred in pure form. Even the highest-grade particles 'wore contaminated by fine, interlocked grains of barite, calcite, and silica; barite contamination predominated, and the barite was interlocked with varying amounts of bastnaesite. While the specific gravities of pure bastnaesite and barite (approximately 5.0 and 4.50 respectively) differ enough to allow separation by gravity, the interlocking of the minerals nullified this difference. Consequently, only a partial separation could be made by gravity concentration. The extremely fine grained texture of most of the ore prevented grinding to a size that would make concentration by flotation practicable; a partial separation of barite by this means was effected.

Jan 1, 1952

By G. W. Jones

From evidence made available during the investigation, it was concluded that the first of a series of explosions occurred at 1:15 to 1:20 p.m. September 21, 1951, in an underground vault that housed pressure regulators on the gas-distribution lines that served Brighten. This explosion damaged the pressure regulators and permitted high-pressure gas to enter the distributing mains and individual-service lines. As a part of the gas-distribution system was not provided with means for protection against such excessive pressures, gas gained access to the interiors of many residences in this area and caused a series of disastrous explosions and fires, which took place during a period of approximately 2 hours after the initial explosion in the pressure-regulator vault. Two persons were killed in the first explosion in a residence, and a third person died of a heart attack attributed to the excitement that prevailed during the explosions and fires, Twenty-three persons were listed as injured. Forty-one residences were either destroyed or damaged - 11 by explosion and the remainder by fires, which developed as a result of gas leakage into residences. Fifteen residences were listed as "completely down" or "gutted." Unofficial estimates of property damage ranged from $1,000,000 to $1,500,000. In view of observations made and information obtained during the investigation, recommendations are presented in this report relative to the natural-gas distribution system in Brighton, which may be helpful in the prevention of similar accidents in this and other communities.

Jan 1, 1952

By H. C. Fuller

This paper discusses 105 production runs at Boulder City, Nev., in which titanium metal was made in 200-pound batches. It describes the equipment and techniques used in preparing raw material, the reduction process, and the removal of the reaction mass from the reaction vessel. Also, some data on man-hour requirements are presented. The main emphasis was on producing ductile-grade titanium and developing a standard procedure for obtaining a consistently pure product. Some departures from techniques used before were found to be desirable. The most important of these was the use of a sealed room with a controlled dry atmosphere in which the reaction vessel was opened and the reaction mass removed. This minimized the moisture taken up by the magnesium chloride in the reaction mass, and it could be purified successfully by vacuum distillation. Using the dry room also made it possible to leave al-inch shell of the reaction material on the walls of the vessel, which lowered the iron contamination and eliminated the labor and time-consuming job of cleaning the vessel after each reduction. Another change was lowering of the temperature during reduction to 750° C. instead of 850° C. This was found to give good results more consistently. The first poke to break the crust during reduction was eliminated, as it was found to be unnecessary and only added more work and was another possible way of introducing air. A rotating feed arm was installed in the reaction vessel to distribute the titanium tetrachloride over a larger area and, thus, prevent local overheating. The process, conducted in a batchwise manner as described and followed by good purification and fusion, produces a metal adequate in quality for nearly all purposes.

Jan 1, 1952

By R. R. Wells

As a part of the strategic mineral program, examining engineers of the Bureau of Mines collected samples several manganese properties in Colorado. As all of the ores were too low-grade to be acceptable to manufacturers of ferromanganese, beneficiation studies were required .to determine the amenability of the ores to concentration. Manganese in the form of impregnations in sedimentary beds is found in the Denver plains area a few miles east of the Rocky Mountain front. Deposits are reported to occur intermittently over a distance of more than 200 miles. The manganese oxides occur in beds of conglomerate or arkosic sand, generally accompanied by limonite. The Manganese and iron oxides,, however, usually are found in separate layers. Three samples were submitted for beneficiation tests, two samples from Buckley Field bombing Yang, Arapahoe County, and one from near Franktown, Douglas County.

Jan 1, 1952

By O. C. Blade

A comparison of certain properties of the commercial aviation gasolines produced in the United States during October 1949, 1950, and 1951 is presented in table 1, the 1951 data being average values from tables 3 through 6 of the present report. Trends in the average values of certain characteristics of these fuels may be seen in figures 1 through 4 which also indicate the minimum and maximum values. As may be observed, with the exception of changes in kinematic viscosities, the properties of commercial aviation gasolines have not varied greatly during recent years. A list of aviation-gasoline survey reports published by the Bureau of Mines is given on page 6. A summary of the average values of the properties on jet fuels is shown in table 2.

Jan 1, 1952

By G. B. Shea

In the search for possible future sources of petroleum products, the recovery and utilization of bitumens from the large outcropping deposits of bituminous sandstones in the United States have been under study by the Bureau of Mines for the past several years. The results of laboratory research in the adaptation of the hot-water separation process to recovery of bitumen from bituminous sandstones were reported in an earlier publication, on the Edna deposits near San Luis Obispo, Calif. This publication included analytical data on the cracked products and asphalts obtained from the extracted bitumen and on the cracking and distillation of the bitumen. Comparable hot-water separation tests have been run in the San Francisco, Calif., laboratory of the Bureau of Mines on quarry samples from the large deposits of bituminous sandstones near Vernal and Sunnyside, Utah. The bitumens were isolated from the extracts of the separation plant and analyzed at the Petroleum and Oil-Shale Experiment Station of the Bureau of Mines, Laramie, Wyo. Part I of this report summarizes the general characteristics of the Vernal and Sunnyside deposits and discusses the hot-water separation process as applied to those bituminous sandstones and the results obtained. The separation tests showed that these bituminous sandstones also respond to treatment by the hotwater method of separation. The bitumen in the Vernal sandstone was extracted more readily by the action of hot water than was the Edna bitumen, which greatly simplified plant operation. The Vernal sandstone contains no water-soluble iron compounds, such as were found in the Edna sandstone, and, therefore, required no preliminary water washing. Recovery of bitumen from the Vernal sandstone was about 96 percent.

Jan 1, 1952