Search Documents

By J. H. Wiggins

"The tests described below were conducted by the Bureau of Mines at a lease in Oklahoma on installations designed to decrease evaporation losses of crude oil Pram storage tanks. Use of the lease was granted by the Oklahoma Producing and Refining Corporation of America. Tankage was obtained through the courtesy of the Parkensburg Pig and Reel Co. The purpose of the installations and tests was to demonstrate the value of making crude-oil storage tanks gas-tight, rather than to determine the amount of evaporation in any one type of tank. None of the tanks used were absolutely gas-tight, but one of them was very nearly so. They comprised a tank of the ordinary open type with an 18-inch manhole, a tank with a ""4-inch vent"", a tank with a ""smaller vent"", and a tank which had only ""pin holes"" through which air and vapor could pass freely. On the last two tanks any excess pressure was taken care of by an automatic differential pressure regulator.The results obtained in these tests indicate that tight tankage will soon pay for itself. They will not, however, serve as a basis on which a producer can compute the actual number of days necessary for tight tankage to pay out, because the oil used was exceptionally volatile. It is probable that the average evaporation loss in the Mid-Continent field is at least one-half as great as that shown by these tests, and if this is true, the saving that would be effected by providing tight tankage on the lease will undoubtedly justify the expense. The installation of evaporation-proof tanks on the lease has been delayed by the failure of production managers to realize, first, that their evaporation losses are enormous, and, second, that they can practically eliminate these losses by a simple and inexpensive installation."

Apr 1, 1921

By R. V. Ramani, P. M. T. White, D. Sutton

This report was prepared by The Pennsylvania State University under USBM Contract No. G0111808. The contract was initiated under the Coal Mine Health and Safety Program. It was administered under the technical direction of DMSE, with Mr. G. R. Schottler acting as the technical project officer. Mr. J. A. Herickes was the contract administrator for the Bureau of Mines. This report is a summary of the work recently completed as part of this contract during the period June, 1971 to December, 1973. This report was submitted by the authors on March 31, 1974. The project personnel express their thanks to Dr. Jay Politzer, The Pennsylvania State University Computer Center for providing the subroutine POLITZ and function IFIND, to Dr. Ray Masters, Department of Architectural Engineering, for permission for the use of the GRID program and to Dr. Lother Weyher of Bethlehem Steel Corporation for providing coal data.

Jan 1, 1974

By Bruce I. Thomas

Reconnaissance studies of beach sands along the eastern part of the Gulf of Alaska were conducted by the Bureau of Mines to determine if any of these coastal areas warranted investigations as possible sources of valuable minerals. Because of difficult access and limited transportation facilities only a minimum of sampling, surveying, and camping equipment is utilized to obtain spot samples from key areas as well as information indicating the location, size, and character of the deposits. Such data were obtained from beaches located along approximately 247 miles of the Gulf of Alaska coastline during parts of the 1957 and 1958 field seasons. A total of 201 3-inch-diameter auger holes, spaced roughly at 1 mile intervals, were bored by hand methods to depths ranging from 3 feet to 27 feet; also 33 shovel samples were collected from selected localities. Samples were reduced to a rough concentrate in the field by panning; the rough concentrates were shipped to the Bureau of Mines laboratory at Juneau for further concentration and for petrographic and chemical analyses. Particular attention was given to the heavy-mineral content of the concentrates, although the types and relative amounts of rock-forming minerals were also determined. The reconnaissance indicated that, generally, the valuable mineral content of the beach deposits was too low to be of further interest except in the vicinity of Yakutat and Lituya Bays where erratic but possibly significant concentrations of magnetite and/or ilmenite were found. At Yakutat, about 20 miles of beachline extending southeasterly from Ocean Cape, yielded samplas containing from 1 pound to over 300 pounds of iron and from a trace to over 100 pounds of titanium dioxide (TiO2) per cubic yard of beach material. However, the higher grade samples represented local concentrations of minor importance. The general tenor of the Yakutat beach, as indicated by the airthmetical average of 27 auger-hole samples, is about 35 pounds of iron and 20.5 pounds of titanium dioxide per cubic yard of beach material. Ilmenite is the predominant heavy mineral of the beach deposits in the vicinity of Lituya Bay, but it was found in concentrations only in limited areas near the

Jan 1, 1962

By John J. Henn

An evaluation is presented for an ammonium sulfate leaching process designed to extract manganese from Cuyuna, Minn., and Aroostook, Maine, deposits. In this process the manganese and iron in the ore are reduced to MnO and Fe 3 0 4 in a shaft furnace; the reduced ore is then leached with ammonium sulfate solution forming soluble manganous sulfate while leaving most of the iron undissolved. After filtration, the manganese and some impurities are precipitated from solution as carbonates which are then pelletized and calcined to form a product composed mainly of Mn3O4. The plants are designed to produce 100 tons per day of manganese contained in a product that is suitable for the production of ferromanganese. A byproduct credit, together with the extra processing cost, is included for the Cuyuna ore processing plants because Fe2O3 may be recovered for use in blast furnaces. The estimated operating costs per ton of manganese, excluding income taxes and return on investment, are: [ ] The process with or without byproduct recovery, when treating Cuyuna or Aroostook ores, is not economically competitive with ores available at $71.43 per ton of contained manganese.

Jan 1, 1968

By Reinhardt Thiessen

This paper presents only the highlights of previous research on the paleobotany of coal. The accumulated material has become so vast that a comprehensive review of all findings relating to paleobotany would be far too long. The fact that coal is derived from plants is now so well-known that no further comment is required, but knowledge of the mode of transformation of plant substances into coal is not so general. The plant matter goes first through processes of semirottins-, maceration, and elimination of certain material to form peat, which is then further transformed into coal. The first stage has been termed the "biochemical process," because the more important changes take place under the influence of micro-organisms. Near the end of the biochemical action an unconsolidated peat is formed. The second or "dynamochemical process," caused by the addition of superincumbent rock strata such as sandstones and shales and application of additional pressure and possibly heat through mountain-building forces, results in the formation of higher-rank coals ranging from brown coal to anthracite. These stages in trans-formation of plant material to coal have been described in previous reports.4 The main object of this paper is to bring to the notice of paleobotanists the fact that coal contains an enormous amount of material in a remarkably good state of preservation. Although some of the coal-forming matter has lost its identity, much of the original structure is retained. A large proportion of the coal, therefore, particularly of common bright coals, comprises constituents or components that invariably have retained some of the original plant structure, and many of these structures may be assigned to certain plants. The identity of these plants and of the remains forms the subject of this paper.

Jan 1, 1941

By James H. Gary

Data regarding the composition and physical properties of Florida land-pebble phosphate-waste slime are presented, and the feasibility of dewatering and beneficiating the slime by several different methods is discussed. Chemical analyses, electron micrographs, and X-ray diffraction data showed that principal constituents of the slime included quartz, attapulgite, and flaorapatite. Viscosity of the slime changed with pH; thixotropic, Newtonian, and rheopectic states were observed as the pH increased. Use of various flocculating agents was not effective in improving thickening properties of the slime. Dewatering tests using pressure filtration showed that temperature influenced the filtration rate more than pressure; the filtration rate at 165° C was tenfold that at room temperature. Selective flotation of the slime, using two different processes, gave promising results. About 25 pct of the phosphate was recovered in a concentrate assaying 31 pct P205, Other tests demonstrated that the slime could be successfully fractionated at 20-microns using a hydrocyclone. In hydrometallurgical tests about 80 pct of the phosphorus and alumina were chemically extracted from the slime using sulfuric acid. Limited bacteriological studies made of the slime showed that several types of microorganisms were present and grew in the material despite the presence of fluorine-bearing minerals.

Jan 1, 1963

By D. R. Mathews

Electrorefined vanadium was evaluated with respect to tensile properties and the effects of interstitial contaminants in the temperature range of 77° to 273° K. The yield strength of 18,500 psi and hardness of 63 diamond pyra-mid hardness (DPH) of electrorefined vanadium are approximately equal to that of iodide crystal bar vanadium. The ductile-brittle transition temperature was found to be below 77° K, but with 0.175 weight-percent oxygen or 0.10 weight-percent nitrogen, it increased to between 123° and 190° K. With carbon content up to 0.11 weight-percent, the transition temperature remained below 77° K. The yield strength of the interstitial-containing alloys can be expressed by: au = 7.5 + 480 (pct N) + 290 (pct 0) + 280 (pct C), where au is the upper yield stress in 1,000 psi at 273° K. Profuse deformation twinning occurred in the alloys tested at 77° K. However, twinning could be suppressed by dissolved oxygen or nitrogen in excess of 0.15 and 0.086 weight-percent, respectively. Carbon, even though present in excess of the solubility limit, did not affect twinning.

Jan 1, 1965

By John B. Goodman

This report summarizes the work done by the Koppers Company, Incorporated, in cooperation with the Bureau of Mines on the commercial evaluation of the primary low-temperature tars produced from Texas lignite in the Rockdale, Tex., plant of the Aluminum Company of America in conjunction with the Texas Power and Light Company. The interest of the Bureau of Mines in this project is twofold. First, through its cooperative agreement with the Texas Power and Light Company the Bureau has assisted in the technical design and practical operation of the prototype, externally heated, entrained-state carbonizer for producing char for electric-power production and for primary low-temperature tar. Second, the first successful operation of the prototype carbonizers employing the Bureau of Mines-Parry process on lignitic coal in 1953-54 led to the production of large quantities of primary lignitic tar, concerning which too little was known or had heretofore been published in this country.

Jan 1, 1959

By Townsend. James W.

"INTRODUCTION As a byproduct of its mineral investigation program, the Bureau of Mines has developed a number of operating devices and techniques worthy of note. This paper, prepared under the direct supervision of Paul T. Allsman, chief, Salt Lake City Division, Branch, and under the general supervision of Lowell B. Moon, chief, Mining Branch, reports upon one such device. A simple device has been developed for measuring angles of deviation from the horizontal as recorded on a glass tube by acid etching. The device has facilities, also, for measuring the angle between the long axis of the ellipse and the north-south reference points established by a Maas compass or from an established axial lamina, on the tube, which was ori¬ented to a specific direction in the hole by rod alinement.The device was found accurate within half a degree on repeated orientations of the same tube. However, the degree of accuracy is dependent on the accuracy of personal manipulation in orienting the tube to the correct plane."

May 1, 1947

By J. B. Gayle

Oven widths for experimental and commercial slot-type ovens differ appreably in most instances; the experimental ovens usually ranging from 10 to 14 inches and the commercial units from 14 to 21 inches. Application of results obtained with experimental ovens to commercial practice thus requires major extrapolations. A critical survey of the literature indicated that sufficient information about the effects of variations in oven width on the carbonizing process is not available to permit such extrapolations to be made with any considerable degree of confidence.

Jan 1, 1960

By J. T. May

The Federal Bureau of Mines investigated the extraction of lithium from hectorite-type clay deposits found on the Nevada-Oregon border. Two clay samples were used in the investigation; one contained 0.36 pct Li and the second contained 0.64 pct Li. The purpose of this laboratory-scale research was to determine how these clays responded to different extraction techniques. Extraction techniques investigated were sulfuric acid leach, sulfuric acid bake-water leach, and roast-water leach procedures with cholorides, sulfates, carbonates, and combinations of these reagents. The processing characteristics of the clay samples showed significant variations, and no one technique was effective for both materials. Lithium extractions near 90 pct were achieved during these exploratory studies.

Jan 1, 1980

By S. H. Katz

In the Bureau of Mines investigations of respiratory apparatus, a laboratory study of dust respirators has been conducted, and the results will be published in detail as a technical paper. Many industrial dust respirators, and many fabrics and filtering materials were tested. The principal results of these tests, and the conclusions drawn from them, are presented below. Reference to the patent literature discloses numerous types of dust respirators, mostly based on the filter principle. The present study included only representative filter-type respirators, purchased on the market.

Jan 1, 1926

By S. J. Schatzel, W. P. Diamond

Longwall mining alters the fluid-flow-related reservoir properties of the rocks overlying and underlying an extracted panel due to fracturing and relaxation of the strata. These mining-related disturbances create new pressure depletion zones and new flow paths for gas migration and may cause unexpected or uncontrolled migration of gas into the underground workplace. One common technique to control methane emissions in longwall mines is to drill vertical gob gas vent holes into each longwall panel to capture the methane within the overlying fractured strata before it enters the work environment. Thus, it is important to optimize the well parameters, e.g., the borehole diameter, and the length and position of the slotted casing interval relative to the fractured gas-bearing zones. This paper presents the development and results of a comprehensive, "dynamic," three-dimensional reservoir model of a typical multipanel Pittsburgh coalbed longwall mine. The alteration of permeability fields in and above the panels as a result of the mining- induced disturbances has been estimated from mechanical modeling of the overlying rock mass. Model calibration was performed through history matching the gas production from gob gas ventholes in the study area. Results presented in this paper include a simulation of gas flow patterns from the gas-bearing zones in the overlying strata to the mine environment, as well as the influence of completion practices on optimizing gas production from gob gas ventholes.

By R. Karl Zipf

Use of Salamon's stability criterion in underground mine design can prevent the occurrence of catastrophic domino-type pillar failure. Evaluating the criterion requires computation of the local mine stiffness and knowledge of the post failure behavior of pillars. This paper summarizes the status of the practical use of this important criterion and suggests important research to improve our capabilities. Analytical and numerical methods are used to compute the local mine stiffness. Work to date in computing local mine stiffness relies mainly on elastic continuum models. Further work might investigate local mine stiffness in a discontinuous rock mass using alternative numerical methods. Existing post failure data for coal pillars are summarized, and a simple relationship for determining the postfailure modulus and stiffness of coal pillars is proposed. Little actual postfailure data for noncoal pillars are available; however, numerical models can provide an estimate of post failure stiffness. Important factors controlling postfailure stiffness of rock pillars include the postfailure modulus of the material, end conditions, and width-to-height ratio. Studies show that the nature of the failure process after strength is exceeded can be predicted with numerical models using Salamon's stability criterion; therefore, a method exists to decrease the risk of this type of catastrophic failure. However, the general lack of good data on the postfailure behavior of actual mine pillars is a major obstacle. Additional back-analyses of failed and stable case histories in conjunction with laboratory testing and numerical modeling are essential to improve our ability to apply the stability criterion.

Jan 5, 1999

By Forrest T. Moyer

INJURY experience and employment data are presented in this (chapter for metal and nonmetal mines, stone quarries, sand and gravel pits, iron-blast-furnace slag plants, and metallurgical plants (including ore-dressing and nonferrous reduction plants and refineries) in the United States. Employment and injury experience data for all mineral industries are given in volume III. The 1963 figures are preliminary and are subject to revision. METAL MINES Preliminary estimates for the metal-mining industry of a combined fatal and nonfatal injury-frequency rate of 32.34 per million man-hours in 1963 indicate only a slight change from the rate of 32.00 in 1962. Metal operations had 41 fatal and 3,110 nonfatal injuries during 1963.

Jan 1, 1964

By Jerry Olson

The Bureau of Mines (Bureau) conducted a mineral resource investigation of the French Creek-Patrick Butte study area, in west central Idaho during 1989. No mineral resources or significant occurrences were identified. Other than small scale placer gold, no mineral production is known or recorded. At least 100 lode and 150 placer claims have been located in the study area. Most of the area was examined by ground or areal surveys, and 110 lode and 60 placer samples were taken. Four lode prospects were examined in detail, and all placer claim locations were sampled.

Jan 1, 1991

By Robert Alfred

This paper is one of a aeries being published by the Federal Bureau of Mines on methods and practices used in mining and preparing crushed stone for market. Performance, in terms of units of work or tons produced per machine and per operator man-hour, is given whenever that information can be obtained. Direct operating costs are useful for comparing different methods and are included if available. In addition to descriptions of equipment and methods used the Bureau considered it desirable to discuss the engineering reasons for the choices that have been made, This paper is particularly concerned with the operation of the Liberty quarry and plant of the Campbell Limestone Co, The plant is in Pickens County, adjacent to the main line of the Southern Railway, and is about 18 miles west of Greenville, S, C. Access also is available by United States Highway No, 123, The company's main offices are at Knoxville, Tenn.

Jan 1, 1958

By James H. Russell

The Bureau of Mines, U.S. Department of the Interior, in cooperation with the Department of Energy, has attempted to increase the activity of nickel catalysts for converting synthesis gas, derived from coal, to a substitute natural gas. This report describes the effects of low-level additions of B, Ca, Ce, Co, Mn, Mo, Pd, Re, Ti, Y, Zn, and Zr on the methanation activity of Raney nickel. The methanation rate at 320° C and the resistance to poisoning by 2 ppm H2S were used to compare catalysts. The effects of the additions were small, and the experimental variances were large, necessitating the use of statistical methods to identify significant effects. Co, Ti, Y, and Zn improved the resistance to H2S poisoning, but only Co improved the methanation rate In some individual catalysts containing Ca, Mo, or Mn, both the methanation rate and resistance to H2S poisoning were improved.

Jan 1, 1980

High resolution seismic refraction tomography has proved to be a useful tool to effectively estimate depth of blast induced damage in a mine face. Excavation blast damage can be as shallow as 1 to 2m and requires resolution at a fraction of a meter for effective imaging. We used an accelerometer with flat frequency response to 1000Hz to record data at spacings of approximately 0.25 to 0.5m along mine walls. First arrival times from the seismic data were used to produce P-wave velocity tomograms. The tomograms show transition from low velocity zones to velocity associated with competent rock. We interpret the low velocity zones to indicate residual fracturing from blasting. Experiments on a concrete test block and at two underground mine locations give results that are consistent with fractured rock transitioning to competent rock. Our method can be applied efficiently in an underground environment to provide continuous velocity information with depth into a mine wall over a span of approximately 10m.

Jan 1, 2009

By W. E. Lamont

The Federal Bureau of Mines conducted research to develop methods of removing phosphorus from the earthy, calcareous hematite ores of the Birmingham, Ala., iron district while simultaneously improving the grade and recovery of the iron values prior to furnacing. An attempt was also made to identify the phosphorus minerals present in the ores. The ores contained about 36 percent iron, 12 to 16 percent CaO, 15 to 20 percent hydrochloric acid insolubles, and 0.30 to 0.36 percent phosphorus. Fractions containing 5 to 15 percent phosphorus were isolated from the ores. Collophanite, Ca3P2O3?nH2O, a member of the apatite group, was the only phosphate mineral identified. Beneficiation methods using flotation and reduction roasting with magnetic separation yielded good grade iron concentrates, but were not as effective for reducing the phosphorus content of concentrates. Reduction roasting followed by fine grinding, magnetic separation, and acid leaching gave iron concentrates containing 62.5 percent iron and 0.04 percent phosphorus with an iron recovery of 82.9 percent and a phosphorus rejection of 93.7 percent. Reoxidation of reduced magnetic concentrates followed by acid treatment gave iron concentrates containing 58.1 percent iron and 0.02 percent phosphorus with 89.6 percent recovery of the iron and 96.5 percent rejection of the phosphorus.

Jan 1, 1973