Search Documents

By A. Gene Collins

This report discusses some of the chemistry and geochemistry of cesium and rubidium. Knowledge of the cesium and rubidium content of oilfield waters aids in resolving the origin of waters and petroleum, exploring for petroleum and other valuable minerals, discovering water pollution sources, and augmenting the knowledge of geologic formations. The methods described in this report permit the detection of less than 0.01 mg/l of cesium and/or rubidium in a complex oilfield brine or water. Solvents possessing high-dielectric constants were evaluated for their ability to extract cesium and rubidium tetraphenylboron from oilfield waters and for their flame emission characteristics. Nitroethane was selected and used for the extraction and flame spectrophotometric determinations because it gave the highest sensitivity. Cesium 137 and rubidium 86 were used to determine the extraction efficiencies, which were about 87 percent and 58 percent respectively using a single 10 ml nitroethane extraction from a distilled water matrix. The standard deviation of the determination was 0.0008 mg for cesium and 0.0007 mg for rubidium in the 0.01 mg range.

Jan 1, 1965

By W. E. Young

This study was made to present the mining methods and costs of a uranium mine typical of other mines in the highly productive Westwater Canyon member of the Morrison formation in New Mexico. Four mining methods have been used at the Section 23 mine: the retreat- room-and-pillar method, a sublevel-slicing method (also called top-slicing), the horizontal-cut-and-fill method, and a modification of the ring-drill method. The application of the methods at this mine and at other mines in the area should be of benefit to operators with similar problems. Ore bodies in the Section 23 mine are irregularly shaped and vary in size, in rock strength, in moisture content, and in uranium concentrations; different mining methods are required and mining costs are not constant. A 6-month period of operation at the Section 23 mine was analyzed and mining costs, not including amortization, depreciation, or Federal taxes, averaged about $6.80 per ton.

Jan 1, 1965

By W. S. Landers

This report presents a detailed study of low temperature, entrained-bed carbonization of an Australian coking coal. The coal studied was high-volatile B bituminous from the Foybrook mine, an open-cut operation in the Liddell seam, New South Wales, Australia. Carbonization was conducted in an 8-inch diameter, continuous vertical reactor at several temperatures from 960° to 1,300° F. It was demonstrated that this bituminous coal can be carbonized within this temperature range to produce tar and a nonagglomerated char, without prior oxidation or char recirculation. Carbonization rates from 138 to 287 lb/hr (as-carbonized basis) were investigated. It was found that the carbonization temperature and the air-to-coal ratio must exceed minimum values to insure continuous operation. At the higher air-to-coal ratios employed, all or most of the carbonization heat was provided by internal combustion with air in the reactor. At the lower air-to-coa1 ratios, part of the heat for carbonization was supplied externally. On the moisture-and ash-free basis, the yield of tar plus light oil ranged from about 26 to 44 gallons per ton, and the char yield ranged from approximately 1,160 to 1,370 pounds per ton. The heat in the gas ranged from about 900 to 3,000 Btu/lb of moisture-and ash-free coal. Carbonization product yields correlated well with air-to-coal ratio and carbonization temperatures. The volatile matter in the char was found to be temperature dependent. At 1,300° F carbonization, the volatile matter in the char was 8.7 percent (dry basis), whereas at 9600 F carbonization, the residual volatile matter was about 16 to 18 percent (dry basis).

Jan 1, 1965

The principal activities of the Bureau of Mines Explosives Research Center from July 1, 1963 to June 30, 1964 are described briefly in part 1. Part 2 gives short abstracts of publications that appeared during fiscal year 1964; in general, the research reported in these publications antedates the report period. Part 3 describes a short-term investigation into safety problems associated with shipping of molten sulfur; this investigation is not at present destined for publication elsewhere.

Jan 1, 1965

By Jr. Norman

Thermoelectric properties of depleted uranium selenides and tellurides were investigated from room temperature to 700 C. Several depleted uranium monoselenides and monotellurides were doped with selected cationic and anionic materials to determine the effect of impurity additions on the thermoelectric properties. The undoped uranium selenides and tellurides were semimetallic conductors exhibiting low Seebeck coefficients and electrical resistivities. Partial or complete degeneracy was in evidence, indicating a charge carrier energy distribution similar to that in a metal. Doping increased the Seebeck coefficients of the uranium monoselenides and monotellurides; however, the corresponding change in the power factor in the figure of merit was small because of the increase in electrical resistivity.

Jan 1, 1965

By G. A. Crowder

Far infrared spectra, most of them in the region 15-200 microns and for both the liquid or solution state and for the vapor state, were obtained for twenty-seven compounds.

Jan 1, 1965

By Stephan Stecura

Crystallographic modifications and kinetics of solid-state phase trans-formations were determined for five rare-earth" sesquioxides--La2O3, Nd2O3, Sm2O3, Eu2O3, and Gd2O3. Oxides used for crystal modification studies were prepared by thermal decomposition of the following high-purity salts of the five rare-earth elements--carbonates, chlorides, fluorides, nitrates, oxalates, and sulfates. X-ray diffraction patterns of the cubic and hexagonal oxides were indexed by a graphical method and patterns of the monoclinic oxides by Ito's method. The kinetics of crystallographic transformation were determined by high-temperature X-ray diffractometry. The kinetic data were interpreted using a shrinking sphere model. All of the transformations followed first order kinetics. Activation energies were calculated by application of the Arrhenius equation. These solid-state phase inversions were concluded to occur by a reconstructive transformation mechanism.

Jan 1, 1965

By C. O. Hawk

A PART of the Bureau of Mines effort to improve the conversion of coal to liquid fuels, batch autoclave tests were made on the hydrogenation of bituminous coal by a dry method, which featured charging the autoclave with dry ingredients only-coal, catalyst, and hydrogen. This innovation, which omitted the liquid vehicle used in earlier work, limited the products to those made from the coal charged. The effects of the common process variables (catalyst, hydrogen pressure, temperature, and residence time) were studied. Tin catalysts showed the highest activity in the widest variety of forms and were the easiest to disperse; dry mixing in the autoclave during the heating-up period usually sufficed. Ammonium molybdate, on the other hand, was inactive when dry mixed, but it compared favorably with the best catalysts known when applied by impregnating the coal with a solution of a molybdenum compound. As a group, metal naphthenates were the most effective; in fact, molybdenum naphthenate was the most active catalyst the Bureau tests disclosed. One-hundredth of a percent of molybdenum in this form (calculated as the metal in weight-percent of maf coal) induced 90-percent conversion of coal. However, because of their high cost, naphthenates have as yet only technical significance in coal hydrogenation. Long residence time and high reaction temperatures tend to increase the amount of thermal decomposition products formed (light hydrocarbon gases and/or char). High hydrogen pressure favors the production of liquids.

Jan 1, 1965

By K. C. Dean

This report is the first of a series concerned with processes for producing magnesium. These reports will evaluate metallothermic, carbothermic , and electrolytic production methods, and will furnish a cost basis for comparing the processes. Areas deemed most promising for future research will be delineated for each procedure. This report presents briefly the history of the metallothermic process, and describes the operations of the Defense Plant Corp. (DPC) plants that employed the process. A hypothetical plant designed to produce 12,000 tons of magnesium per year, using ferrosilicon as a reductant, is described, and raw materials, energy, and major equipment requirements are estimated. Several process modifications are suggested for future research.

Jan 1, 1965

By A. T. Harris

Ground quartzite, known in the industry as amorphous silica, is produced from a quartzite deposit near Honey Brook, Pa., by George F. Pettinos, Inc., of Bala-Cynwyd, Pa. The quartzite is mined by the open pit method and processed in a mill at the mine. The operation regularly produces five standard grades of sand and one grade of crushed stone; however, the company accepts special orders and will produce material to meet the customer's specifications. Beneficiation (chiefly crushing and screening) is controlled by laboratory screen tests on samples taken during preparation of the sand. The chief uses of the sand are for foundry operations, furnace lining, concrete aggregate, and Other specialized uses. The quartzite in this deposit is of uniform composition and does not require control by chemical analysis. However, for special purposes, analysis will be furnished.

Jan 1, 1965

By Tilman M. M.

The effects of substituting cobalt for nickel on the acid corrosion resistance of two types of austenitic stainless steel were determined. Cobalt substitutions to a maximum 2.2 weight-percent were made in types 302 and 309 stainless steels. Total immersion corrosion tests were made in 10 volume-percent hydrochloric acid, and boiling-acid tests were conducted in 65 weight-percent nitric acid and in undiluted glacial acetic acid. For modified type 309 in acetic acid, corrosion rates decreased for additions greater than 0.57 weight-percent cobalt. Corrosion rates increased as cobalt was increased up to about 1 weight percent for modified type 302 in nitric and hydrochloric acids and for modified type 309 in nitric acid, but these rates decreased with a further increase in cobalt content. A gradual increase in corrosion rates with increasing cobalt content was shown for type 302 in acetic acid and for type 309 in hydrochloric acid. Cobalt substitutions in larger amounts (above a ratio of 8 Ni to 1 Co) may increase the corrosion resistance of the austenitic stainless steels.

Jan 1, 1965

By L. B. Pankratz

Heat contents, measured above 298.15° K, and derived entropy increments are presented in tabular and equation form for the two crystalline forms of zinc sulfide (sphalerite and wurtzite) and for four solid solutions of iron and zinc sulfides having the compositions Zno.,,6Fe0.302S, Zno.750Fe0.250S, Zno.650Fe0.3505, and Zno.498Feo.502S.

Jan 1, 1965

By James D. Brown

The Bureau of Mines has written a computer program in FORTRAN to facilitate the calculation of concentrations from X-ray intensities in electron probe microanalysis. Philibert's absorption and Castaing's secondary fluorescence corrections are used; no atomic number correction is included. Background and dead time corrections are applied to the data before calculating the relative intensities. Data from any type of electron probe microanalyzer can be used with the program.

Jan 1, 1965

By J. B. Gayle

The Bureau of Mines studied the effects of air oxidation on the recovery of float coal. Both batch-and continuous-type tests were made on six bituminous coals, representing the range in rank of coals now commercially used for carbonization, and on one anthracite coal. The effects on flotation recovery of oxidation at 1000 C for periods up to 50 days were investigated using an alcohol-type frother and a kerosine-pine oil reagent. Two series of release analysis tests were made, using one medium-volatile bituminous coal. Float coal recovery was adversely affected by oxidation in all tests where the alcohol-type frother was used. Conversely, a small degree of oxidation improved recovery with kerosine-pine oil frother for some of the coals in continuous tests. Prolonged oxidation (beyond about 14 days) adversely affected float coal recovery for all coals, the effect being more pronounced for batch-type tests and for tests using alcohol-type frother. Reagent selectivity for the rejection of both ash forming and sulfur bearing minerals was reduced by oxidation. Severe reduction of reagent selectivity required only about 3 days' oxidation for alcohol-type frother but more than 10 days' oxidation when the kerosene-pine oil reagent was used.

Jan 1, 1965

By S. J. Gasior

A method for destroying the caking properties of bituminous coal was developed by the Bureau of Mines. Coal is treated in a fixed bed by heating through its plastic range under controlled temperatures in mildly oxidative atmospheres composed of inert gas and/or steam containing about 1 volume-percent oxygen. High-volatile A (hvab) and high-volatile B (hvbb) and low-volatile bituminous (lvb) coals in the size range 1/8 to 1-1/2 inches were successfully treated at 0 (atmospheric pressure) to 300 psig in static beds 6 to 18 inches deep. Conditions of treatment depended on the coal and ranged from 80 to 200 minutes at 350° to 510° C. Char produced in this manner from hvab coal was gasified with steam at 800° C and 100 psig in a fixed bed in one series of tests and in other tests was exposed to hydrogen in a dilute co current free-falling-bed system at 750° C and 3,000 psig without agglomerating.

Jan 1, 1965

By George R. Schottler

The objective of this research is to find the extent of the range of applicability of previously developed statistical methods for determining grade and tonnage of ore to bedded uranium deposits. Uranium assays obtained from gamma-ray logs of exploratory drill holes are used to compute grade and tonnage of ore in the deposit by a standard polygonal method and by statistical analysis. The results obtained by the two methods are compared. The uranium-assay frequency distributions are shown to be lognormal and a simple transformation permits the use of standard normal curve statistics. The effects on the assay frequency distributions of stratified sampling, a required minimum mining thickness, and increased assay-interval length are investigated. The addition of low-grade mineralization to make up the required minimum mining thickness results in a distinct change in the skewness of the assay frequency distribution. Any statistical inference regarding grade-tonnage relationships that will be produced, using the minimum mining thickness, should be made on the basis of this "revised" assay frequency distribution.

Jan 1, 1965

By George S. Scott

The Bureau of Mines conducted ignition, flammability, and decomposition experiments on gas mixtures containing ethylene to determine its flammability characteristics at elevated pressures and ambient temperatures. Pure ethylene was found to propagate a decomposition reaction at 1,000 psig and ambient temperatures when ignited with 1 gram or more of guncotton in a 2-inch-id bomb. The decomposition products were primarily carbon, methane, and hydrogen.

Jan 1, 1965

By James R. Boyle

The mining methods and practices used at the Young zinc mine, American Zinc Co. of Tennessee, have resulted in a low-cost, high-yield operation. Zinc ore (sphalerite) occurs in limestone-dolomite beds of the Kingsport Formation and is mined by modified room and pillar method. Utilizing trackless mining equipment which incorporates a high degree of flexibility, this operation has had a steady increase in productivity.

Jan 1, 1965

By Kung-Lee Wang

SUSTAINED growth characterized the U.S. economy in 1964. Many new peaks were achieved in production, sales, employment, employee earnings, and business profits. At the end of 1964, the economy had experienced 4 years of uninterrupted expansion, and the greatest net gains in output for all postwar cyclical advances had been registered. There were no indications of the various weaknesses which have previously characterized advanced stages of business expansion. Both gross national product (GNP) and national income were 6.7 percent higher than in 1963. In 1964 GNP totaled $628.7 billion, a gain of $39.2 billion over the 1963 figure. On an overall basis, prices rose 1.75 percent in 1964. The real volume of output of goods and services (GNP in constant dollars) increased by 5.0 percent ill 1964; this was more than the 3.8-percent gain in 1963 but less than the 6.6 percent gain in 1962. The 1964 output gain also exceeded the average 3.7 percent annual increase for the postwar period. Congress authorized a two-stage tax reduction designed to further stimulate economic growth and employment. The tax cut favorably affected the 1964 economy in the following ways: By helping to boost personal income, corporate profits, and industrial production; by accelerating the pace of consumer spending and business capital expansion; and by increasing employment, thereby reducing unemployment to 5 percent. Three major problems remained unsolved. These were unemployment of 3.7 million persons, poverty conditions among more

Jan 1, 1965

By D. R. Mathews

The solubility of carbon in electrorefined vanadium was determined to be approximately 0.27 wt pct at the eutectic temperature 1,650° C and 0.03 wt pct at 700° C. The tensile strength and hardness of vanadium increased with car-bon content to the solubility limit, but this effect was small, probably because of the narrow solubility range. Between the solubility limit and 0.3 weight-percent carbon, the second phase had essentially no strengthening effect in vanadium. The second phase, observed metallographically at the grain boundaries and within the grains, was shown by autoradiography to contain high-carbon concentrations. This second phase was identified as VgC by X-ray analysis. The VgC in the grain boundaries contributed largely to the poor cold-and-hot workability of vanadium-carbon alloys. Increased concentrations of V2C occurred at the grain boundaries of the high-carbon alloy ingots as a result of homogenization at 1,600° C for 1 hour. Alloy ingots containing more than 0.36 wt pet carbon (a calculated 2.9 wt pct VaC) following homogenization, cracked severely and failed by intergranular fracture upon swaging at 900° C.

Jan 1, 1965