Search Documents

By Hannweg L. A.

In a first for the diamond industry, Koffiefontein Mine in the Free State, South Africa, opted for the front cave mining method to extract a 90 metre high block of kimberlite ore. Block caving, because of its high initial capital requirements, resulting in a negative internal rate of return (IRR),was ruled out as a feasible mining method for Koffiefontein Mine. Front caving is essentially a combination of the traditional block cave and sub-level cave mining methods, but uses two or more levels of retreating drawpoints. Two extraction levels, in the case of Koffiefontein Mine, are spaced 12 m apart vertically, with the upper 478 m level (48Level) acting as the undercut/extraction level, and the lower 490 m level (49 Level) as the extraction level. Caving is achieved by undercutting a small column of ore, which is then drawn, on both the 48 and 49 Levels, until the planned extraction percentage is achieved. The next column of ore is then mined by advancing the undercut (48 Level), and the process is repeated until the entire ore block is depleted to the contact. Caving-by-gravity techniques of mining rely on closely controlled draw of the caved ore to ensure proper caving action and to minimize the dilution of ore with waste material from the open pit. This paper discusses the need for, and implementation of, a draw control system at Koffiefontein Mine — a computerized production management system, and a draw control system based on linear programming, to allow control over the draw rate and mining sequence — a major factor in all production planning to optimize production efficiency, ore recovery and cave management. Keywords: Draw control, Koffiefontein Mine, Front cave, Caving

Sep 1, 2001

By R. B. Khumalo, M. S. Nyarela, R. C. Nemathithi

Palabora Mining Company is one of the largest low-grade copper mines globally. The mine uses block caving for the extraction of the orebody. This paper enumerates the drawpoint loading strategies for the overall head grade improvements, particularly for a block that is nearing depletion. A comprehensive literature review of various considerations relating to improving productivity in block caving is presented to contextualize the draw control in caving. From this study, an optimized draw control strategy is presented, which focuses on three parameters that include grade distribution, loading compliance, and tonnage splits per sector. An empirical method based on the relational study between various parameters is used to outline the key criteria to be used in the optimization of drawpoint loading in block caving.

Nov 30, 2022

By R. Hummel

In the quest to reduce overall costs and improve operating efficiency, the application of GPS based technology in open pit mining has evolved significantly in recent times. Venetia Mine has been leading the way in the De Beers group in the implementation of these systems and the realization of significant benefits from them. Following on from the successful results and the notable benefits obtained from the Wenco Truck Dispatching system and the Caterpillar CAES system on the loading and dozing equipment, Venetia has implemented the first fully functional and integrated GPS based drill monitoring system in southern Africa to its drilling operations. This paper elaborates on the concept of drill monitoring and how the vision for the application of the system at Venetia has developed and been implemented. The paper further describes the workflow involved, beginning with the initial test work done with SSI Kaltex and the Australian Drill Advisor system through to the final details of the integration of the Aquila system with the CATERPILLAR Computer Aided Earthmoving System (CAES) and the alliance with SandvikRock Tools. Most importantly, the paper details the benefits that are derived from drill monitoring and the use of the information generated by such a system. Venetia has pioneered the move towards smart partnerships and alliances with strategic suppliers within the De Beers group. The area of drilling, as the important start of the entire mining process, has been no exception and the final part of the paper covers how drill monitoring provides vitally important information that enables a supply partnership, to function cost-effectively and profitably for both parties involved. By having the type of accuracy, detail, validity and timeousness in the information being received as a result of the implementation of such a system, better management decisions can betaken, creating a more focused and efficient mining environment. In these times of increasing costs and reduced commodity prices, the mining industry will be required to continue pushing the boundaries on these technology applications in order to remain competitive.

Sep 1, 2001

Drilling, Blasting, and Ore winning A General Meeting and Colloquium on the above subject was held on November 13th, 1974, at Kelvin House, Johannesburg. Professor R. P. Plewman (President) was in the Chair. The Colloquium was attended by 235 delegates and was opened by the President at 09h30.

Jan 1, 1975

By L. Rojas Mendoza, F. J. Hrach, A. Gupta, K. P. Flynn

ST Equipment & Technology (STET)’s tribo-electrostatic belt separator technology allows for the beneficiation of fine mineral powders by means of an entirely water-free technology with high throughput and low energy consumption. The STET separator is suited for separation of very fine (<1 μm) to moderately coarse (500 μm) particles, in contrast to other electrostatic processes that are typically limited to particles >75 μm in size. STET has performed exploratory studies with several iron ores including tailings and experimental results to date have demonstrated that low-grade iron fines can be upgraded by means of STET tribo-electrostatic separator to commercial grades (58-65%Fe). Experimental results together with high-level economic evaluations indicate that scavenging processes involving low drying costs, DSO operations and tailings beneficiation offer a commercially viable processing method to recover fine iron that would otherwise be lost by traditional processing. Dry electrostatic processing of iron ore presents a clean, low-energy opportunity for iron producers to reduce costs and wet tailings generation associated with traditional gravimetric, flotation and wet magnetic separation circuits. Moreover, STET technology allows for mining waste utilisation and resource recovery from iron ore fines and tailings, therefore offering processors a novel method to recover fines that would otherwise be difficult to process to sellable grades with existing technologies. Keywords: Iron fines, industrial minerals, dry separation, calcium carbonate, talc, barite, quartz, tribo-electrostatic charging, belt separator, fly ash

Jan 1, 2020

By M. Le Roux, Q. P. Campbell, N. Hughes

Water plays a significant role in minerals processing; this is especially true in coal preparation where water-based beneficiation is widely accepted and consistently delivering sharp separation efficiencies and high product yields. Although wet processing is favoured, the substantial process water requirement may prove this impractical and unsustainable in some parts of the world. Many coal-rich regions (including South Africa) have experienced severe water shortages. Coupled with the effects of drought, some countries experience freezing winters from which problems related to frozen process water and machinery may arise. Hence coal preparation practices will soon have to adapt, irrespective of the technical and economic feasibility offered by the currently employed water-based methods. As a result, extensive research into the development of dry methods for effectively beneficiating coal has progressed. This review paper intends to provide a collection of the relevant information pertaining to dry coal processing globally, and aid in understanding the applicability, performance, success or failure thereof. The methods available for dry materials preparation, with special regard to those applicable for coal beneficiation, are detailed in terms of principle, applicability, limitations and performance. Dry coal beneficiation has potential to aid the current wet-based methods with some considerations to possible limitations set forth by coal geology, application, product specification, particle size distribution, moisture, efficiency, capacity and cost. These methods may be established in future, especially in the arctic, arid and under-developed regions through new plant installations, expansions and small mines processing. Keywords: Dry coal processing, preparation, cleaning, beneficiation

Jan 1, 2020

By L. von Ketelhodt

Dual energy X-ray transmission (DE-XRT) sorting is a recent development in the range of sensor-based sorting technologies available today. DE-XRT is particularly suitable for dry coarse coal beneficiation in the size range -120 mm +12 mm. In this paper, we describe the technology and show the results of a number of test runs conducted on different types of coal from the USA and South Africa. The results have shown that DE-XRT is an effective technology not only for deshaling of coal and removing pyritic sulphur but also for separating coal and torbanite. The use of dry deshaling methods will be more important as water availability becomes a greater concern. DE-XRT is one such technology which will be incorporated in future dry coal processing plants.

Jan 1, 2010

This paper sets out to consider a specific type of corrosion protection system, which is referred to as a Duplex Coating system. The dictionary describes a duplex system as consisting of two elements or a “twofold” composition. The duplex system described in this presentation is such a two-part corrosion protection coating, viz, hot dip galvanizing as the firm base or primer, followed by a top paint system designed to combat severe corrosive environmental conditions encountered in nature. In principle, the duplex system is a cost effective and balanced, designed coating that is suited to the environmental conditions and service life requirements.

Jan 1, 2009

By G. Dhakal, J. -I. Kodama, K. Neaupane, T. Yoneda

ABSTRACT Durability tests and evaluation of sub-zero temperature effects to some argillaceous clastic rocks were carried out. Welded tuff, limestone, sandstone and schist samples collected from different parts of Japan were tested and results are presented. Schist and dolomite from Ganesh Himal area along the higher Himalayas of Nepal were also tested, and the results are compared. The slaking tests were performed on all samples in pure water. The results reveal that the slaking index of schist from Japan is lower than that of schist from Nepal. Regarding carbonate rocks, the slaking index of limestone from Japan is higher than that of dolomite from Nepal. A tendency of decrease in slake durability with an increase in porosity is also observed. Freezing and thawing experiments conducted on welded tuff and schist reveal that crack initiates earlier but extends slower in schist than in welded tuff. It is also observed from the freeze-thaw experiment that the welded tuff deteriorates and wears faster than the schist. However, sandstone remains relatively intact for a long run of freeze-thaw cycles. Zusammenfassung Beständigkeitstests sowie die Bewertung der Auswirkungen von Minusgraden auf Tonschiefer Trümmergestein wurden durchgeführt. Dabei wurden geschweißter Tuff, Kalkstein, Sandstein und Schiefer aus verschiedenen Gebieten Japans sowie Schiefer und Dolomitgestein aus dem Ganesh Himal Gebiet, dem höheren Himalaya Nepals, untersucht und die Resultate verglichen. Für alle diese Gesteine wurden Slaking-Tests in reinem Wasser vorgenommen. Die Resultate zeigen, dass das Slaking von Schiefer aus Japan höher als das von Schiefer aus Nepal war, wohingegen bei kalkhaltigem Gestein das Slaking von Kalkstein aus Japan niedriger als das von Dolomitgestein aus Nepal ausfiel. Es wurde dabei auch eine Tendenz zur Löschbeständigkeitsverringerung bei gleichzeitig erhöhter Porosität beobachtet. Gefrier- und Tautests an geschweißtem Tuff und japanischem Schiefer zeigten, dass Risse in Schiefer schneller auftraten, aber sich langsamer ausweiteten als in geschweißtem Tuff. Bei Gefrier- und Tautests wurde ebenfalls beobachtet, dass geschweißter Tuff schneller verfällt und verschleißt als Schiefer. Sandstein hingegen blieb über lange Tau- und Gefrierzyklen intakt Résumé Des tests de solidités et l’évaluation de l’effet des températures en dessous de zéro sur les rocs argileux ont été effectués. Les rocs d’origine volcanique (cendre), les rocs calcaires, sableux et les schistes de différentes régions du Japon, ont été étudiés. Les schistes et les dolomites de la région de Ganesh Himal le long du haut Himalaya (Népal) ont été étudiés et comparés à ceux du Japon. Les tests de désintégration sur les rocs ont été effectués dans l’eau pure. Les résultats montrent que l’index de désintégration des schistes du Japon est inférieur aux schistes du Népal. En ce qui concerne les rocs carbonyles, l’index de désintégration des rocs calcaires du Japon est supérieur à ceux des dolomites du Népal. Une décroissance de la résistance à la durabilité est observée avec une plus grande porosité des rocs. Les tests de congélation-décongelation sur les schistes et les rocs d’origine volcanique (cendre) du Japon montrent une apparition précoce des fissures mais l’expansion des fissures est plus rapide dans les rocs volcaniques. Des tests similaires montrent que les rocs volcaniques (cendre) se désagrégent plus rapidement que les schistes. Cependant, les rocs sableux restent intacts après plusieurs cycles de congélation-décongélation.

Jan 1, 2003

By R. G. Coyle

"In an earlier paper the author explored the consequences of price-stabilizing effects, on an industry-wide basis, of various production strategies. These ideas have now been applied to an illustrative case of an individual mine. It is shown that the turning of production and financial policies can affect financial performance over a five-year period by as much as 22 per cent.No generality is claimed for the results and they would differ from mine to mine. It is, however, asserted that the results show that the proper turning of production, reserves and financial policies are more critical determinants of mine performance than has been realised. It is also asserted that the methods of dynamic analysis are the most appropriate means for studying this policy-design problem."

Jan 1, 2014

By J. Drzewiecki, J. Kabiesz

Coal mining using longwall methods of mining can lead to intense disturbances of undermined roof strata. The disturbances may extend beyond the extraction area and the resulted rock mass deformations will appear differentiated. In the case of stiff and undermined roof strata, the energy stored in these rock masses may be frequently dissipated in the form of high-energy seismic tremors. Such events can occur if these strata should fail or „free themselves” either from the constrainment of rock environment or from adjacent strata. It has also been found that the amount of the stored energy closely depends on the size and/or slenderness of these strata. Thus, it would be possible to apply specific preventive measures to reduce the energy of mining – induced seismic tremors. The methods are based on artificial disintegration of the structure of energy – storing strata. One of the most efficient methods is a method of directional hydraulic fracturing, which is regarded as an alternative solution from the traditional blasting and hydraulic methods.

Jan 1, 2003

By G. van Aswegen, J. D. Bosman

Gold bearing deposits in the Witwatersrand consist predominantly of narrow tabular conglomerates with quartzite host rock. Extensive mining of these deposits at depth results in significant stresses being induced in the periphery of the tabular excavations. Where remnant pillars are created excessive stresses have resulted in the dynamic failure of the abutments. At the Hartebeestfontein Mine four brittle shear zones have recently been exposed and investigated. For most part, they represent abutment failure into the weaker hangingwall strata, striking parallel to the abutment, dipping towards the stope, with a sense of displacement consistent with closure of the stope from above. These shear zones are similar to those described in various publications by Ortlepp2: they are essentially brittle shear zones characterised by the presence of very finely comminuted ‘rock flour’ on an obviously freshly sheared surface. The angle between the shear zone wall and extension fractures indicate the sense of shear and the intersection of the extension fractures with the shear zone walls define a strong lineation normal to the direction of slip. It is suggested that these structures are referred to as ‘mining induced dynamic brittle shears’. Les gisements d’or du Witwatersrand consistent principalement de conglomérats tabulaires peu épais contenus dans une quartzite mère. Une exploitation poussée de ces gisements en profondeur a pour résultat l’apparition d’importantes contraintes induites à la périphérie des excavations tabulaires. Là où des piliers restants sont créés, des contraintes excessives ont eu pour résultat une rupture dynamique des appuis. Dans la Mine d’Hartebeestfontein, quatre zones fragiles de cisaillement ont été récemment exposées et étudiées. Dans la plupart des cas, elles représentent une rupture des appuis dans les strates moins solides de la paroi suspendue, orientée parallèlement à l’appui, inclinée en direction du chantier d’abattage avec une direction de mouvement consistante avec l’affaissement du toit de la galerie d’abattage. Ces zones de cisaillement sont similaires à celles décrites par Ortlepp2 dans diverses publications: Ce sont essentiellement des zones cisaillement fragiles caractérisées par la présence de « farine de roche » très finement réduite sur une surface évidemment fraîchement cisaillée. L’angle entre la paroi de la zone de cisaillement et les fractures de tension indiquent le sens du cisaillement et l’intersection des fractures de tension avec les parois de la zone de cisaillement définit une forte délinéation perpendiculaire à la direction du glissement. Il est suggéré que l’on se réfère à de telles structures comme des « cisaillements dynamiques fragiles induits par l‘exploitation ». Goldablagerungen im Witwatersrand bestehen überwiegend aus schmalen tabularen Konglomeraten mit Quarzitwirtgestein. Der umfangreiche Abbau dieser Ablagerungen in der Tiefe resultiert in signifikanten Drücken, die auf die Peripherie der tabularen Aushöhlungen wirken. Wo Restpfeiler hergestellt wurden, resultierten exzessive Drücke im dynamischen Versagen der Auflager. In der Hartebeestfontein Grube wurden kürzlich vier spröde Scherzonen freigelegt und untersucht. Zum größten Teil representieren sie Auflagerversagen im Stratum der schwächeren Stollenfirste, parallel zum Auflager verlaufend, in Richtung Abbaustelle abfallend, mit einem gewissen Grad an Verschiebung konsistent mit der Schliessung der Strosse von oben. Diese Scherzonen sind jenen ähnlich, die in den verschiedenen Publikationen von Ortlepp2 beschrieben werden: sie sind im Wesentlichen spröde Scherzonen, charakterisiert durch das Vorhandensein des sehr fein pulverisierten „Gesteinsmehls“ auf einer offensichtlich frisch abgescherten Oberfläche. Der Winkel zwischen der Scherzonenwand und den Bruchverlängerungen deutet die Richtung der Scherung an und die Kreuzung der Bruchverlängerungen mit der Abscherzone grenzt sich gegen eine starke Lineation normal zur Richtung der Lehne ab. Es wird vorgeschlagen, daß diese Strukturen als `vom Abbau verursachte dynamisch spröde Scherungen’ bezeichnet werden.

Jan 1, 2003

By C. Steyn, J. D. le Roux

A dynamic model is used to represent the single-stage closed grinding mill circuit at Mogalakwena North Concentrator. The circuit consists of a ball mill closed by a hydrocyclone. The circuit is modelled according to a semi-mechanistic non-linear dynamic model available in literature. An algebraic routine is used to fit model parameters to steady-state process data. Preliminary validation results against dynamic data indicate that the model is capable of capturing the main dynamic trends of the plant. Since classical system identification techniques proved insufficient to produce accurate models; the non-linear model can be used as a reliable source for model-predictive controller design. Keywords: Grinding, modelling, process control, parameter estimation

Jan 1, 2020

By U. Singh, E. T. Brown, J. Coxon

The rapid fracturing and deformation that occurs around excavations during rock bursts demand that support and reinforcement systems have both deformability and damping capabilities. The energy demand and supply approach currently used in design is considered to be too simplified to represent adequately the rock burst process and the support and reinforcement system requirements. Momentum change may be a necessary second criterion for the analysis of dynamic loading situations. At the St Ives Gold Mining Company, DE plates made from conveyor belt rubber, and dynamic cables with sliding anchors have been developed and used to improve the dynamic performance of support and reinforcement systems. La fracturation rapide et la déformation qui se produisent autour des excavations lors de coups de terrain demandent que les systèmes d’armature et de support soient déformables et aient une capacité d’amortissement. L’approche basée sur l’énergie actuellement utilisée pour la conception est considérée être trop simplificatrice pour représenter adéquatement les coups de terrain et les paramètres de conception des systèmes d’armature et de support requis. Le changement de quantité de mouvement pourrait être un second critère nécessaire pour l’analyse des cas de charge dynamnique. St Ives Gold Mining Company a développé et utilisé des plaques « DE » constituées de caoutchouc de courroie de convoyeur et des câbles dynamiques avec ancrage coulissant afin d’améliorer la performance dynamique des systèmes d’armature et de support. Die ploetzliche Rissbildung und Verformung, die sich in Baugruben waehrend eines Felseinbruchs ereignet, verlangt Stuetz- und Verstaerkungssysteme, welche verformbare und mildernde Eigenschaften aufweisen. Die derzeitlich gebraeuchliche Methode den Entwurf auf den Energiebedarf und dessen Abdeckung zu basieren, wird als eine unannehmbare Vereinfachung betrachtet, da sie den Felseinbruch und die benoetigten Unterstuetzungs– und Verstaerkungssysteme unzulaenglich darstellt. Die Aenderung der Umstaende kann einen zweiten Ansatz fuer die Analyse der Lastsituation erforderlich machen. Die St.Ives Gold Mining Company hat DE Platten aus Foerderband-Gummi und elastischen Kabeln mit verschiebbaren Verankerung entwickelt und dazu verwendet, die dynamische Kapazitaet der Unterstuetzungs- und Verstaerkungssysteme zu verbessern.

Jan 1, 2003

By M. R. Grant, G. S. Kruger, H. D. van der Merwe, T. N. Huffman

Sixteenth to seventeenth century Kalanga miners dug a series of sub-vertical shafts into a 10 to 30 m wide zone of copper ore at the Thakadu Mine near Matsitama, Botswana. They went down at least 6 m in search of thick malachite veins. The host rock was hand &apos;cobbed&apos; to remove the veins, which were then smelted nearby in small bowl furnaces. Evidently, the furnaces lacked clay superstructures, since a simple pit was sufficient to smelt the almost pure malachite. The copper bloom was probably refined in villages further away.

Jan 1, 1995

By H. Hu, T. S. Golosinski

The paper reports on use of neural network algorithms to model performance and condition of mining trucks. The model inputs are selected digital data streams collected by truck Vital Information Management System, VIMS, during its operation in a mine. The models built as the result of this work allow for projection of truck condition and performance into future. As such they facilitate more efficient management of mine truck fleets. Keywords: Modelling, modeling, neural networks, mining equipment, Vital Information Management System, Intelligent Miner, mining truck

Jan 1, 2003

By J. W. Klokow, S. L. Mulder

Early removal of the shaft reef is usually considered necessary on deep level South African gold mines to avoid damaging stress build-up associated with traditional shaft-protection pillars. In the case of the relatively shallow Beatrix Gold Mine it was largely motivated by early access to ore and the consequent earlier return on invested capital. A number of options were considered to protect the shaft from possible damaging stress changes and to minimise deformations in the shaft-reef area. Numerical modelling was used to evaluate the options and to quantify as accurately as possible the likely deformations to be accommodated by the shaft steelwork designs. The option chosen was a combination of strategically placed satellite pillars and yield pillars, and backfill. Following the mining of a small inner cut during the shaft sinking process, full-scale mining is progressing away from the shaft. Suitable instrumentation has been installed to monitor deformations associated with the shaft reef removal. Enlever rapidement le filon du puits est en général considéré nécessaire dans les galeries de fond des mines d’or sud-africaines pour éviter l’accumulation nuisible de contraintes associée aux piliers de protection de puits traditionnels. Dans le cas de la mine d’or Beatrix, relativement peu profonde, l’enlèvement était motivé en grande partie par l’accès rapide au minerai et par conséquent un profit plus rapide sur l’investissement. Un certain nombre d’options furent considérées pour protéger le puits contre les changements de contraintes potentiellement nuisibles, et pour minimiser la déformation dans l’aire puits/filon. La modélisation numérique fut utilisée pour évaluer les options et pour quantifier aussi précisément que possible les déformations probables que la conceptualisation du puits devrait prendre en compte. L’option choisie fut une combinaison de piliers satellites placés à des points stratégiques avec des piliers de protection, et terre de remblayage. Pendant le fonçage de puits une petite coupure intérieure fut exploitée, et maintenant l’exploitation à grande échelle, au-delà du puits, est en cours. Les instruments nécessaires ont été installés pour surveiller les déformations associées à l’enlèvement du filon du puits. Die frühe Entfernung des Riffschachtes wird normalerweise bei südafrikanischen Tiefbaugoldmienen als notwendig erachtet um den zerstörende Druckaufbau zu vermeiden, welcher mit traditionellen Schachtschutzpfeilern verbunden ist. Im Fall der verhältnismäßig flachen Beatrix Goldmine war es hauptsächlich vom frühen Zugang zum Erz und dem konsequenten frühen Rückfluß des investierten Kapitals motiviert. Eine Anzahl an Optionen wurde erachtet um den Schacht vor möglichen zerstörenden Druckänderungen zu schützen und Deformationen im Riffschachtbereich zu minimieren. Um die Optionen zu bewerten und mögliche Deformationen so genau wie nur möglich quantitativ darzustellen die von den Schachtstahlkonstruktionen aufgenommen werden müssen, wurden numerische Modelle verwendet. Die gewählte Option war eine Kombination aus strategisch plazierten exzentrischen Pfeilern und Schutzpfeilern sowie Hinterfüllungen. Nach dem Vortrieb eines kleinen inneren Einbruches während des Abteufens wird der Vollvortrieb vom Schacht weg vorgenommen. Um die Deformationen, die mit der Riffschachtentfernung verbunden sind zu überwachen, müssen geeignete Instrumentenausrüstungen installiert werden.

Jan 1, 2003

Mixed integer programming (MIP) has been used for optimizing production schedules of mines since the 1960s. The major problem in the long-term production scheduling for an entire orebody is that the number of integer variables needed to formulate an MIP model is too large to solve the formulation. This number may reach well over one hundred thousand. To overcome this difficulty, this paper presents two new algorithms to reduce the size of the problem. These algorithms assign an earliest and latest possible start date for each machine placement, eliminating the integer variables that correspond to machine placement before its early start date and after its late start date. A case study based on Kiruna Mine, the second largest underground mine in the world, is summarized in the paper. It shows substantial improvement in the solution time required using the new algorithms. This increased efficiency in the solution time of the MIP model allows it to be applied to Kiruna Mine, with the potential to increase substantially the net present value (NPV) of the project.

Jan 1, 2008

By H. T. Clausen

This paper gives a brief review of the main environmental and ecological problems of slimes dams, both those created in the immediate vicinity of the dams and those influencing the region or catchment. Methods of dealing with these problems and influences on existing dams are described. The difficulties encountered in the growing of grass on steep slopes are explained, and, after an analysis of the conditions, a plea is made for flatter slopes on the sides of dams.

Jan 12, 1973

By T. Uysal

The increasing demand for rare earth elements (REE) in highly strategic sectors such as hybrid electric vehicles, renewable energy, communication technologies, and the defense industry has made REE production methods important. In recent years, studies on REE have increased rapidly; however there are many studies on REE, there are not enough studies in the literature on the economics of the beneficiation process. RE ores are generally leached after beneficiation by gravity, magnetic and flotation methods. In this study, direct leaching, attrition scrubbing and leaching, and flotation and leaching methods are evaluated economically based on the data for the Mountain Pass (MP) facility. According to the sensitivity analysis performed as a function of capital cost (CAPEX), operating cost (OPEX), and rare earths oxides (REO) recovery, REO recovery has the biggest effect on the process economies. Although the flotation method entails additional investment and operating costs, transportation and operating costs are significantly reduced result of the higher grade and recovery. The flotation method is more profitable, with larger NPV and IRR values and a shorter payback period.

Jul 2, 2022