Search Documents

By M. Nduna

Surface properties of metal sulphides have a great significance in various areas of engineering and science, such as acid mine drainage, contaminant sorption, and metal separation. In various attempts at producing metal sulphide particles from synthetic solutions, prodigious quantities of nuclei that grow only to colloidal dimensions have been frequently reported. This copious nucleation is promoted by the high levels of supersaturation that characterize most precipitation reactions. Colloidal particle formation in precipi¬tation-based separation processes results in sub-optimal solid-liquid separation, which is alleviated by the production of more highly crystalline particles or agglomerates. The current work approaches this challenge from an electrochemistry perspective, by measuring surface charge potential of precipitant particles during metal sulphide precipitation with respect to the concentration of metal sulphide lattice ions in solution. Electrophoresis was used to measure the metal sulphide particle zeta potential and the settling properties were obtained by performing settleability measurements using an Imhoff settling cone. A suspension of copper sulphide particles was precipitated from synthetic solutions of copper and sulphide ions at equimolar concentrations. Immediately after precipitation the copper sulphide particles had a zeta potential of -50 mV and a settleability of about 7 ml.l-1. With the addition of copper ions the settleability increased by a factor of nearly three times and the zeta potential also increased to a maximum of -40 mV. A decrease in zeta potential to a minimum of -60 mV was observed after the addition of sulphide ions and this was associated with a settleability of 0 ml.l-1.

Jan 1, 2013

By L. J. Leach

Quench and tempered Cr-Mo plate steel was found not to contain a fully martensitic structure as a result of either slow slack quenching or insufficient hardenability at the cooling rates used. The resulting microstructure contains bainite in combination with martensite. It is necessary to examine the implications of bainite for the toughness of the final product. Loss of toughness arises primarily from the inter-lath carbides that typically form in upper bainite. An investigation into the effect of upper bainite in a martensitic matrix of a steel grade containing 0.17% C, 0.1% Cr, 0.54% Mo, and 20 ppm Bindicated lower toughness than in a fully martensitic structure.

Jan 1, 2013

By P. G. H. Pistorius, D. S. Konadu, G. Lubbe

The aim of this investigation was to determine whether the composition of a shielded-metal arc-welding electrode coating affected the low-temperature impact toughness of austenitic stainless-steel weld metal. It is generally accepted that increases in the δ-ferrite and nitrogen contents result in a decrease in toughness at low temperatures. Weld metal from electrodes with a basic coating also generally exhibit better toughness than those from rutile (acidic) electrodes. An increase in basicity was expected to decrease the number and size of inclusions, which in turn provides a tougher weld metal. Three commonly available potassium–rutile E308L electrodes were used, complying with the E308L-16 and E308L-17 specifications. Analysis of the electrode coatings showed very similar chemistry and basicity. Significant differences in the inclusion contents of the weld metals were observed: the E308L-17 weld metal had a lower inclusion content (1.4% by volume) than the E308L-16 weld metal (3.7%). The former had higher impact toughness at all temperatures, despite a slightly higher nitrogen content. Regression analysis confirmed that the inclusion content had a significant effect on the impact toughness at all temperatures.

Jul 2, 2022

By B. van Beek, J. H. Zietsman, A. Lexmond, N. J. Andrew

"In platinum group metals (PGMs) smelting, the slag-to-matte ratios are very high (approximately 4:1 to 9:1). The slag temperature therefore has a strong influence on matte temperature, which is a continual concern due to the low matte melting temperature and its resultant high superheat. Maintaining a stable slag temperature is therefore a critical safety and operational issue. This project aims to improve the understanding of the slag bath temperature drivers so that a more effective slag bath temperature control strategy can be implemented.With the aim of developing a multiphysics model of the furnace, extensive data analysis was performed to develop an in-depth understanding of the process before the start of modelling work. In this work, the effect of fluctuating furnace feed composition on slag temperature was examined. The results are based on equilibrium calculations using FactSage, implemented with ChemApp.A method was developed, using an equilibrium calculation at 25°C, to convert the available chemical assays to approximate mineralogical assays in order to determine the feed enthalpies. Actual 2013 furnace feed data was used and the average specific energy requirement to produce slag and matte at 1600°C was calculated to be 671 kWh/t concentrate. The furnace energy input was then kept constant, and it was found that the slag temperature varies significantly as a function of the feed composition. These results were compared to actual slag temperatures measured on site. It was found that close management of the furnace energy balance is important for maintaining a stable slag temperature."

Jan 1, 2014

By K. A. Annan

The last seven hot rolling passes of the ferritic stainless steel AISI430 were simulated on a Gleeble-1500D® thermo-mechanical simulator to investigate the effect of temperature, strain rate, and interpass time on the texture. The compression tests were carried out over a wide range of strain rates (0.1 s-1 to 5 s-1) and temperatures (1100°C to 820°C) with different interpass times (2, 10, 20, and 30 seconds). The dynamic recrystallization to dynamic recovery transition temperature was determined from examining the relationship between the mean flow stress and the inverse of the deformation temperature in multi-pass tests. It was found that the texture in the central layer of the compressed sample is a strong recrystallization-type. The through-thickness textural and microstructural banding, to a large extent, were found to be weakened by hot deformation in the two-phase (a+ ?) region, as opposed to the single-phase (a) region.

Jan 1, 2013

By M. Saghaeian, R. Hejazi, L. Hosseini, M. V. Sheikhzadeh

Blaine number has long been used to evaluate the pelletising ability of iron concentrate in the industry. Much information and practical data are available about the effect of Blaine number on pelletising efficiency of different concentrate types. But not many researchers have focused on the effect of Blaine increasing method on pelletising behaviour of coarse concentrates. In this paper the effect of two different grinding methods (i.e. HPGR and Ball Mill) on physicochemical properties of coarse magnetic concentrate green and fired pellets were investigated. Microstructural studies by Field Emission Scanning Electron Microscope (FESEM) showed that the concentrate for which the Blaine number had been increased through HPGR grinding, has flake-like morphology. In contrast, increasing the Blaine number through ball mill grinding results in more granular particles. Two samples were prepared using HPGR and ball mill. The Blaine number of the HPGR product and ball mill product were 900 cm2.gr-1 and 1200 cm2.gr-1 respectively. The results revealed that pellet properties of this HPGR product are comparable to that of the ball mill product; this is due to the fact that the flake-like morphology leads to enhanced pelletising performance of coarse magnetite concentrates. Keywords: Iron pelletising, Blaine number, HPGR, ball mill, coarse particles

Jan 1, 2020

By Y. I. Yang, Y. -B. Tang, D. -J. Ma

Chlorine-containing minerals are commonly present in coal. Associated minerals such as pyrite can undergo exothermic reactions. Consequently, it is of great significance to study the effect of inorganic chloride on the spontaneous combustion of coal. In this study, the effects of five inorganic chlorides (sodium chloride, magnesium chloride, potassium chloride, calcium chloride, and zinc chloride) on the spontaneous oxidation of coal were investigated. Analysis of the gaseous products of coal oxidization at low temperatures (323K to 453K) showed that the presence of inorganic chlorine in coal markedly decreases O2 consumption and the generation of CO and CO2. Samples of raw coal and chlorine-loaded coal were oxidized for 36 hours under the same experimental conditions. Infrared diffuse reflectance spectroscopy results showed that inorganic chloride can inhibit the oxidative decomposition of some functional structure components (methyl, methylene, methine, and hydroxy) in the coal. The influence of inorganic chloride on the oxidation characteristics of the functional groups in coal during spontaneous combustion was investigated using benzyl alcohol and 1-phenylpropanol as model compounds, which were tested under the same experimental conditions as the coal samples. The oxygen consumption of model compounds with and without the addition of inorganic chloride further suggested that inorganic chloride may hinder the oxygenolysis of these structures during low-temperature oxidation. This phenomenon can be attributed to the radical reaction from the perspective of radical chemistry. It can therefore be concluded that inorganic chlorides play an inhibitory role in the spontaneous combustion of coal.

Jan 1, 2015

By M. R. MacIver, M. Pawlik, H. Alizadeh

Treatment of tailings is an integral component of mineral processing. Tailings with a high clay content are a challenge for the mineral processing industry; e.g. the clay slimes produced from production of phosphate in the mid-western United States and the fine tailings produced from oil sands production in western Canada. Dispersants are a commonly used process aid, but their impact on the structure and settling properties of high clay content tailings is not well understood. The paper describes the changes in composition and bitumen release that occur when mature fine tailings (MFT) are treated with a polymeric dispersant (lignosulfonate.) Synchrotron-source computed tomography (CT) was used to obtain high-resolution 3D images of samples prepared at varying dosages of dispersant. The CT method permits a powerful visualisation of the internal structure and composition of the samples. These insights will enhance our understanding of the structural characteristics of mineral tailings relevant to solid-liquid separation by flocculation and thickening. Keywords: Dewatering, dispersion, dispersants, chemical treatment, computed tomography

Jan 1, 2020

By K. C. Sole, M. E. Mitshiabo

Although surfactants have proven to increase metal extraction by improving solution flow in porous media, these reagents have not been widely adopted in heap leaching operations because of potential incompatibilities with downstream processes that are subject to surface properties. The BASF leaching aid, LixTRA 118, was previously found to have no significant effect on post-leach operations. This study evaluated its performance in ores of different particle size distributions and the impact on acid consumption and metal recovery. Column leach studies, carried out on a copper oxide ore and mixed oxide–sulfide ore, showed that the effect of LixTRA 118 was more pronounced in ores with wider particle size distributions than in those with more uniformly sized particles. Solution percolation rates increased by up to 18% in the presence of leaching aid, and increased copper recovery and acid consumption. Improved wetting facilitated the kinetics of acid diffusion at macroand micropore level. There was no significant effect on iron recovery

Jan 1, 2023

By S. M. Bradshaw

In order to assess the requirements for online matching when using a transverse electric field (E-field) applicator to treat mineral ores continuously, the effect of varying load properties on matching has been investigated by simulation. The effective permittivity of the ore to be treated is expected to show variation on both short (< 1 s ) and long (minutes) time scales. By modelling the ore as a series of slices with alternating effective permittivity values, it was shown that permittivity variations on the scale of the expected particle size are attenuated significantly and matching is not required. For variations in permittivity on the length scale of the free-space wavelength, variations in reflected power are at most within ±10% of the mean. This is not considered operationally significant, as extreme permittivity variation over this length scale is unlikely, given the expected distribution of ore particle sizes to be treated. At typical ore transport speeds through the applicator, these variations occur on a time scale an order of magnitude shorter than the response time of typical industrial online matching equipment. This implies that online matching is neither required nor possible for short time scale variation. Long-term variations in dielectric properties can be adequately compensated for by current matching technologies. It is concluded that the transverse E-field applicator is robust to changes in the dielectric properties of crushed ores within the expected range of their variation.

Jan 1, 2012

By P. G. Toledo, R. I. Jeldres, G. R. Quezada

Chile is the main producer of copper in the world and lately the mining industry has suffered challenges due to the lack of water in the north of the country, along with the new policies of not using fresh water for the industry. This has prompted the use of seawater as an alternative source for mining. Several studies have been driven due to this new scenario, which have shown that seawater can be beneficial, if certain ions are removed from the process. This is the Mg that generates precipitates at high pH, that have been shown to make mining operations difficult. In particular, thickening operations are impaired by the presence of Mg ions, where aggregate formation and sedimentation decreases substantially. Our studies suggest the competence of the precipitates in adhering to the polyacrylamide (HPAM) flocculant and not towards the surface of the quartz minerals. This motivates the present work to use molecular dynamics to study the adsorption of a HPAM molecule on quartz surfaces and the surfaces formed by Mg precipitates. The surfaces are immersed in a saline solution or seawater that includes the HPAM molecule. Results are obtained by measure the adsorption frequency and duration. We obtained that the HPAM molecules are preferably absorbed on the surfaces of magnesium hydroxide. This gives us a good agreement with what is observed experimentally and strengthens the premise of the competition of hydroxide with the flocculant. Keywords: Molecular dynamics, adsorption, tailing flocculation, magnesium removal

Jan 1, 2020

By C. M. Sellars, W. E. Stumpf

SYNOPSIS The effects of concurrent recovery, prior creep deformation and concurrent high temperature fatigue on the coarsening of some carbides in steels have been studied. It was found that concurrent recovery enhances the coarsening rate by orders of magnitude and prior creep deformation causes an enhancement of about two times. Finally, concurrent fatigue causes an initial greatly enhanced coarsening rate but after prolonged cycling dissolution of the carbides occurs.

By R. Boom, J. Halder, B. Snoeijer, B. Deo, A. Overbosch

Operational data of BOF and the slag samples for different starting conditions of phosphorus(0.06–0.26 per cent P) and silicon content (0.3–1.2 per cent Si) of hot metal have been analysed. The contribution of parameters that are well known to affect phosphorus distribution at tap, like basicity, temperature, FeO content of slag, slag mass etc., is investigated through the models of ionic theory of slag, optical basicity, regular solution approach and molecular theory of slag. The best overall results are obtained by the model based on molecular theory of slag in which several operational parameters are also incorporated. The investigations of different slag samples, based on optical, SEM, EPMA and X-ray studies, reveal the effect of MgO and Al2O3on slag morphology and phosphorus distribution in different phases. It is important to consider phosphorus distribution ratio in the solid and liquid part of slag. The solid part of slag, which is mostly dicalciumsilicate, can contain up to 5 per cent phosphorus. The phosphorus content of the liquid part of slag may depend upon the phosphorus content of hot metal or phosphorus load of slag. It is found that incorporation of effect of dicalciumsilicate in the model improves the accuracy of prediction. For better process control, the addition of iron ore towards the end of blow must be avoided while treating high phosphorus hot metal or during the production of ultra low phosphorus steels. Keywords: steelmaking, BOF, phosphorus distribution, slag morphology, MgO, Al2O3,dicalciumsilicate, process control, models

Jan 1, 2004

By L. Li

The performance of microemulsified diesel and conventional diesel collectors in coal flotation was compared by flotation indicators, including combustible recovery, ash content of the clean coal, and the flotation index. An efficient separation with lower dosage was obtained using the microemulsified diesel collector. Under optimum separation conditions, the microemulsion consumption was 100 g/t less compared with diesel. The saving in diesel consumption using the microemulsion reached about 70%, disregarding the consumption of the surfactant and cosurfactant. Frothing tests showed that the frother dosage was decreased by using the microemulsion collector, because of the surfactant and cosurfactant added during preparation. The microemulsified diesel collector is superior to the conventional diesel collector in terms of diesel consumption and separation efficiency, but the selectivity requires further improvement. Keywords froth flotation, microemulsified collector, coal.

Nov 1, 2013

By A. Yañez, J. Yianatos, P. Vallejos, R. Grau

This paper presents an evaluation of the effect that the mineral feed characteristics have on the metallurgical performance in an industrial flotation circuit. Variables such as mineralogy, particle size, solid content and mineral grade were evaluated using a flotation simulator, which was previously developed and validated using industrial data from different concentrators. The metallurgical performance was evaluated not only from the point of view of recovery and concentrate grade, but also by analysing less common variables such as froth carrying rate, froth and collection recovery, water recovery and others. Then, new data from the industrial flotation circuit was used to complement this analysis and evaluate the simulator predictability by comparing simulated and measured data. The results allowed for the quantification of the significant effect that mineralogy and particle size have on recovery and/or concentrate grade. Therefore, the grinding stage and flotation cells design become important factors to avoid a significant loss in metallurgical performance when feed mineral characteristics change in an industrial operation. In this context, an evaluation of cells design and arrangement should be performed to compensate the loss in recovery and concentrate grade in order to find an optimal operating condition. Keywords: Flotation circuits, mineral feed, modelling, particle size, liberation, mineralogy

Jan 1, 2020

By T. Nghipulile, G. Dzinomwa, J. Kurasha, M. Amwaama, B. Mapani, K. Maweja, T. E. Moongo

The effect of mineralogy on the grindability was investigated using three copper ores – two sulphides and one oxide. The dominant copper minerals were identified by optical microscopy and mineral chemistry derived from SEM-EDS analysis. The sample designated sulphide 1 was borniterich, sulphide 2 ore was mainly chalcopyrite, and the oxide ore was predominantly malachite and minor azurite. The gangue minerals were identified using semi-qualitative XRD analysis. Sulphide 1 contained more than 80% (w/w) of quartz compared to about 70% in the other two ores. The Bond work indices were 13.8, 21.6, and 17.3 kWh/t for sulphide 1, sulphide 2, and oxide ore respectively. This suggested that the chalcopyrite-rich ore is the hardest, while the malachite-rich ore has intermediate hardness, and the bornite-rich ore is the softest. The brittleness indices of the ores were calculated using the chemical composition of the gangue, and a good correlation between brittleness indices and Bond work indices was observed, which highlights the importance of the gangue composition in determining the fracture behaviour of the ores. There is scope for further investigation into the relationship between ore mineralogy and comminution behaviour using other breakage characterization techniques.

Mar 30, 2023

By F. Nakhaei, A. Noury, S. Ghodrati

To achieve maximum efficiency in any purification stage, the flotation should be continued until the concentrate grade reaches the feed grade. During sampling from rougher cells of the Iranian Sarcheshmeh copper concentrator plant 1, it was revealed that the concentrate grade of the last five cells of rougher circuit was close to feed grade. Therefore, it was suggested that the concentrate of the aforementioned cells be mixed with rougher feed. In this study, one of eight rougher circuit rows was selected and evaluated. The floatability tests were performed to compare the flotation behaviour of rougher feed and mixture of concentrate of the last five cells with rougher feed in the laboratory scale by a tree analysis process. The results showed that mixing of rougher last five cell concentrate with feed has a detrimental effect on flotation efficiency that leads to a 3% decrease in recovery. It was also observed that with grinding of this concentrate, recovery can be improved. Keywords: Efficiency, flotation, rougher, tree analysis, floatability, concentrate, mixing

Jan 1, 2020

By H. Matsuoka, M. Kawata, K. Mitsuhashi, C. Tokoro, T. Kato

Copper sulfide minerals generally have high floatability, but their floatability decreases when surfaces are oxidised under some conditions. Sodium hydrosulfide, NaHS, is known both as an activator and as a depressant for copper minerals. NaHS at low concentrations activates copper oxides by sulfurising surfaces, but at high concentrations depresses copper sulfides by interfering with the adsorption of collectors. In this paper, we applied NaHS to activate oxidised chalcocite and bornite and focused on the conditions of NaHS treatments such as dosages and pH, and the effect of these conditions on the floatability of those minerals. The pure minerals treated with NaHS were analysed using zeta potential analyser and X-ray photoelectron spectroscopy. Analyses indicated that the reactions of NaHS and the products on the mineral surfaces after the reactions (i.e. oxidation, pH change) depended on whether NaHS reacted with copper or iron, and the reactions between NaHS and iron depend on NaHS concentration and pH. Flotation tests using a small column cell were performed with a single pure mineral, and using a Denver-type flotation machine with a copper sulfide ore. The results of each flotation test were utilised to clarify the floatability. The relation between flotation behaviours and analysis results were also discussed. Keywords: Chalcocite, bornite, NaHS activation, flotation, floatability

Jan 1, 2020

By S. J. Moema, M. G. Maruma, L. A. Mampuru, M. E. Maja

"The most commonly used high-chromium white cast iron (HCWCI) is the hypoeutectic white cast iron that contains 2–3.5 wt.% C and 10–30% Cr. This type of material relies on hard, brittle M7C3 carbides to impart good wear resistance. Due to its good wear resistance, this material has found application in the mining industry and cement industry. However, it has low fracture strength and this challenge led to research aimed at refining the microstructure. This was done by the addition of niobium in the range between 0.1 and 0.6 wt.%. In the as-cast condition, the addition of niobium was found to increase the fracture strength due to the finer eutectic microstructure. The hardness was also found to have increased slightly compared to the reference alloy with no niobium additions. Low fracture strength after heat treatment was observed in the Nb-added HCWCI, which is believed to have been caused by the precipitation of secondary carbides and the transformation of the matrix from austenite to martensitic. IntroductionFor the past few years Mintek has been involved in a project in which a number of alloys have been identified for grinding media applications. The high-chromium white cast iron (HCWCI) alloys were among the alloys researched for this application. The knowledge acquired from the grinding ball media research has now been extended to mill liners, which have traditionally been made of manganese-, chromium- and chrome-molybdenum steels. The replacement of worn mill liners costs the mining industry a significant amount of money and this has led to a need for continuous research to prolong the life of the liners. During milling operations, liner wear has an adverse effect on the capacity of the mill, the energy efficiency and milling efficiency and finally leads to relining, to replace worn liners."

Jan 1, 2016

By C. Machio

This paper reports the results of a study to determine the effect of process control agent (PCA) on the characteristics of Ti-Mg powders during milling. It has been shown that a 2% increase in PCA content leads to up to a 40% increase in yield of the milled powder but reduces the kinetics of the mechanical alloying process. The introduction of 4% PCA decreases the mean powder particle size by up to 30%, whereas 6% PCA increases the mean particle size by up to 230%. The characteristics of the milled powders will be discussed in relation to the role of PCA in the milling process. Keywords Titanium?magnesium, mechanical alloying, PCA.

Jan 1, 2011