Search Documents

By H. Lagendijk, I. J. Reinecke

Mintek was contracted by Oriel Resources plc in 2004 to conduct a preliminary assessment study on smelting ferronickel from the large but relatively low grade Shevchenko nickel ore deposit in Kazakhstan. A detailed feasibility study (?DFS?) was awarded to Bateman BV following promising results from the preliminary assessment study (?PAS?) and small-scale pilot plant test work. As part of the DFS, a total of 450metric tons of ore was collected from three different locations in the deposit and shipped to Mintek. After sampling, the bulk sample was prepared for smelting. This comprised crushing, screening and calcining with each step done separately for the three different lots. The chemical composition of the ore from the deposit is relatively high in silica and therefore falls out of the MgO to SiO2 range that is normally processed by pyrometallurgical means to produce ferronickel. The main objective of the testwork was to demonstrate that a method could be found and successfully applied to smelt these siliceous ores and produce an acceptable nickel-containing alloy. A 2-m ID DC arc furnace was installed with a twin-cathode (electrode) configuration to replicate the proposed commercial-scale furnace and also incorporated an advanced design of water-cooled copper panels in the lower furnace sidewalls to withstand the aggressive nature of the high SiO2-containing slags. The reductant used was a high-volatile coal from Karaganda in Kazakhstan. The reductant addition was adjusted to achieve a 90% recovery of nickel. In the assessment of the process metallurgy, some deviation from equilibrium conditions was observed. This deviation is ascribed to the intermittent existence of a smelting bath partially covered with feed during the testwork. Optimization of smelting conditions should result in the metallurgy (slag metal equilibrium) being closer to the theoretical predictions and make the production of a 20% nickel alloy possible at 90% nickel recovery. The solution for the successful processing of these siliceous ores was found in the attainment of the necessary operational stability through the control of arc length, operating temperature, open-bath smelting conditions and flux additions of up to 10% dolime for the most siliceous of the three ore types. The test work carried out by Mintek provided the basis for the process flow sheet and engineering design of the DC arc smelting furnaces for the Shevchenko Nickel project.

Jan 1, 2007

By D. J. Greeff

By making use of genetic programming, empirical models for metallurgical processes can be evolved that are more cost-effective than models determined by means of classical statistical techniques. These methods explore populations of candidate models assembled from sets of variables, parameters and simple mathematical operators, and do not require explicit specification of model structures. The application of the proposed strategies is illustrated by means of a case study pertaining to the leaching of nickeliferous chromite ores. Modelling of the nickel and cobalt extraction from the ores yielded models of similar accuracy compared to those obtained by non-linear regression and artificial neural networks. However, in the case of the iron extraction from the ores, the genetic programming model was significantly more accurate than both the regression and neutral network models.

Jan 1, 1998

By Sabine Verryn, Johan de Villiers

"Through the application of the Rietveld method, X-ray diffraction analysis has developed into a fully quantitative method for phase analysis. The Rietveld method itself has progressed from an unstable method that required constant operator intervention to a stable and robust method suited even for routine analysis. The method however, requires a good initial calibration and periodic checks on its precision and accuracy.Several examples from minerals processing, pyrometallurgy, and materials science show the strengths and applicability of the method. The limitations and sources of error are also discussed.1. IntroductionDiffraction of X-rays by matter has been used for more than 80 years, initially to elucidate the structure of crystalline matter, and to investigate the bonding between atoms. The first development of powder diffraction cameras and the later development of X-ray diffractometers saw the development of methods to identify phases and to try to quantify them in mixtures. A comprehensive database and search-match techniques have been developed over the ensuing years. Effective and accurate quantification had to wait for the so-called Rietveld' analysis where the total diffraction pattern is used and where the crystal structure data for the constituent phases are needed as input. Overlapping of diffraction peaks of different phases is handled without difficulty and reliable results can be obtained in spite of this occurrence.The development of methods for structure analysis from powder data has also progressed rapidly and more and more complex structures are being solved from first principles, i.e. without knowledge of unit cell or space group data. Because of the ease of use of the Rietveld method, it is finding increased application in metallurgy, especially in the quantification of phases of importance in minerals processing, in pyrometallurgical processes, and in materials characterization. This study will examine the principles of the Rietveld method, its application in metallurgy, and finally also the common pitfalls that need to be avoided.2. Rietve1d AnalysisAs the Rietveld method compares the experimental diffraction pattern with one calculated from known crystal structure data, the following data are needed:•,An XRD Pattern with as Iowa background as possible. This should have good resolution and high diffraction peak intensities. With modem X-ray detectors, this can be achieved in minutes rather than hours.•,Instrumental parameters such as goniometer radii and slit sizes are needed. These are the so-called ""Fundamental parameters"". They are used to calculate the shapes of the resultant diffraction peak profiles that are caused by the instrument. The parameters are used to correctly separate the instrumental effects on the diffraction pattern from the sample effects."

Jan 1, 2014

The South African Institute of Mining and Metallurgy mourns the passing of one of its most distinguished sons. Professor J. de V. Lambrechts died at Franschoek on 30th January, 1988, at the age of 76 years after a long illness. Mintek Application Reports A new series of Mintek reports made its appearance in 1987. These are Application Reports, which present an overall perspective of each of Mintek's technical thrusts to ensure that the existing expertise can continue to be readily accessed. The successful development of an industrial process for the recovery of platinum-group metals from the UG-2 Reef. Application Report no. 1. 1987. 16 pp. The development and implementation of a computer control strategy for conventional milling circuits. Application Report no. 2, 1987. 15 pp. The development of an integrated carbon-in-pulp process for South African conditions. Application Report no. 3. 1987. 17 pp.

Jan 1, 1988

[The following notations will be used: O an ore body. z a point in O. z' another point in O. w0 (z) a point support of infinitely small dimensions w0 centred in z. w (z) a sample (or block) of finite dimensions kv centred in z. W (z) a block of size W greater than or equal to w. W'(z) a block of size W' greater than or equal to W. W" (z) a block of size W" greater than or equal to W'. x (z) value of the regionalized variable x with support wO at point z. p (z) average value of x in w (z). pw WZ) = E[x(z')l zt in w(z) pw (z) average value of x in W (z). pwl (z) average value of x in W' (z). pwU (z) average value of x in W" (z). Note that pW (z), pw (z), pwf (z) and pw,, (z) are (regular- ized) regionalized variables with support w, W, W' and W" respectively. The relative sizes of wO, w, W', W" and O are represented schematically in Fig. 7.1. The variance of pw (z) when w (z) takes all possible positions in O is known as the dispersion variance of w in O and is denoted by a? (w in O) or a\: 0; = a2(w in a = Ew,z, inn {[p~ (z) - p121. (7.1) For convenience, the following simpler notation will be used: a> Ew in n [(p w - pl21. Consider now a large block W (z) in O with average value p~(z), and all the possible smaller blocks (or samples) w (z') of size w in W (z). We can calculate the variance of the blocks w (z') in the block W(z), which is the dispersion vaciance of w in W (z), from the relationship a2 [w in W(z)l = Ewcz,, in W(Z) {[PW (z') -pw (z)l21. (7.2) Provided the intrinsic hypothesis is satisfied (§3.4.4), this variance is a function only of the dimensions of the supports w and W, and is independent of the position z of the block W (z). We can therefore define the dispersion variance of w in W, as follows: u2 (win W) = Ew in w [(ptti - PW)~]. (7.3) In cases where the intrinsic hypothesis is not satisfied, the variance of samples w in blocks W may vary only slightly from block to block, so that the average dispersion variance of w in W (z) for all possible W (z) in O can be used: ayw in W) = Ew(,, ~n n {a2 [W in W (z)]}. (7.4) The following example will help to illustrate the importance of the variance of dispersion. Assume that we plan to develop a bedded coal deposit Q. We consider mining the ore body with only one giant dragline, which will extract each day a block of coal of size W'. The total area mined in a year will have a size W". We want to know whether this scheme is acceptable, given that the daily variation in ash content must not exceed a given percentage specified in the sales contract, which is renewable on a yearly basis. On a given day, if we mine the block W' (z), the ash content will average pwT (z). In a period of one year, the expected daily variation in ash content is measured by the expected variance of pwf (z) in W", i.e. by a2 (W'in W"). An alternative mining method might be to use two smaller draglines, each one mining W'/2 of ore per day, and Wn/2 per year. If the draglines are used to mine two distinct sections of the deposit, the expected daily variation in ash content will be u2 (W'/2 in Wj1/2)/2 Other situations, where economic decisions cannot be made without knowledge of the dispersion variance, are illustrated in § 7.4 and 7.5 below. Remark: The notation a2 (w in W) is used in this publication because of its clarity. An alternative notation, which is increasingly accepted in the literature, is s2w/W. ]

Jan 1, 1978

By M. G. Spengler

Mr More O'Ferrall must be complimented on a paper that will be a useful reference for the re-working of previously abandoned workings. His paper so closely mirrors experiences at East Rand Proprietary Mines, Limited, that it could well have been based on occurrences in that mine. Corrosion The Scientific Society of Mechanical Engineers is organizing the 115th event of the European Federation for Corrosion in Budapest, from 18th to 22nd October 1982.

Jan 1, 1981

By F. J. N. Stassen

SYNOPSIS The effect of conditioning energy on the flotation of gold, U308, and pyrite was investigated in the range 0,1 to 100 kWh per tonne of dry ore for various combinations of conditioning time and impeller speed in a cylindrical con¬ditioning tank. It was found that, when the conditioning energy was increased to between 5 and 10 kWh per tonne of dry ore, the total recovery and flotation rate of the valuable minerals (expressed as Klimpel parameters) increas¬ed substantially. The Klimpel parameters are dependent on conditioning energy, but are independent of condition¬ing time or impeller speed (at constant conditioning energy). The Klimpel parameters of the gangue are indepen¬dent of conditioning energy.

Jan 1, 1991

By S. J. Thomas, P. A. Lilly, J. A. L. Napier

An industry research project has been established to examine the issue of rock mass failure in large open pit slopes. The approach began with numerically modelling failure at the laboratory scale with a displacement discontinuity program. The interim results from the program suggest the output failure mode is dependent upon the input parameter cohesion weakening. Es wurde ein Forschungsproject mit unterstützung von Bergbauindustrie bearbeitet. Die Zielsetzung der vorliegenden Arbeit war die Analysierung des Böschungsgefähr im größen Festgesteinstagebauen. Das Verfahren besteht aus der numerischer Modelierung mit Ansatz einen sonderen Rechnerprogram. Die erste Ergebnis zeigt, daß die Aufgabe am Angabendaten (cohesion) abhängig sein wird. Un project de recherche industriel fût conduit avec le but d’examiner les éboulements de roche dans les mines a ciel ouvert. La premiere étape a été de modelliser numériquement les éboulements dans un laboratoire en utilisant un programme de déplacement discontinu. Les resultants préliminaires du programme indiquent que la prédiction des ébouliements est directement reliée à la magnitude de la cohesion.

Jan 1, 2003

By G. J. de Korte

South Africa’s best-quality coal, located in the central Highveld basin, is becoming depleted and alternative sources of coal, such as the Waterberg coalfield, will have to be developed to supply the country with coal in the future. The quality of the coal being mined in the central basin is gradually becoming poorer. This necessitates that more of the coal be processed to improve the quality to meet customer requirements. The challenge to the coal processing industry is to process low-yielding coals to produce goodquality products and at the same time ensure that coal mining remains economically viable. This requires that more cost-effective coal processing technologies be investigated and implemented.

Jan 1, 2015

By G. L. Smith

This paper introduces and defines the concept of a linkage between long-term planning parameters (?global assumptions?) and possible future world views as conceived in scenario planning. Scenario planning, the tool that is used to arrive at plausible future worldviews, is described in the context of the platinum industry. The interpretation of the scenarios into long-term planning parameters is made, followed by an illustration of how the long-term planning process has been adapted at Anglo Platinum to include the notion of uncertainty.

Jan 1, 2008

By J. Daavittila

In the latter part of the 1980s Outokumpu Chrome in Tornio, Finland, was in a situation when its twenty-year-old ferrochrome plant was becoming too inefficient to sustain economically sound production. The company made extensive studies on the then available processing methods to find out the best possible processing route. As a result, the whole plant was practically rebuilt and expanded. When equipment was proven in practical operation, an application for FeMn production was developed. Now as the Tornio FeCr-plant is considering expansion, the same type of exercise is to be performed with today?s challenges, which will be discussed in the paper. These challenges include increasing costs or decreasing quality of raw materials, increasing energy costs, stricter environmental regulations and demand for better working conditions. The possibilities of resolving to these challenges will be discussed in the paper. The future and continuing development with FeCr includes the better utilization of process dusts and a lower consumption of energy. By adapting the latest automation tools to better control the process, even higher efficiencies can be achieved with present technology. New processes are considered for development in the future and some possible technologies will be described.

Jan 1, 2004

Ladies and gentlemen, it is a privilege to be able personally to welcome you to the opening of this Symposium. It is particularly pleasant to be able to extend a warm South African welcome to al our visitors from foreign shores. We trust you will enjoy your stay in our country. It is a singular honour for me to be present here today, and to have been asked to open this international Symposium. MINING IN SOUTH AFRICA Mining is the single most important contributor to this country's foreign-exchange earnings. Minerals and processed mineral products together account for about 70 per cent of South Africa's total foreign exchange earnings. The mining sector employs in excess of 670 000 people, and is one of the largest employers in the country. The construction and development of cities and towns like Johannesburg, Welkom, Orkney, Springs, Benoni, Witbank, and Klerksdorp is a direct result of the contributions of the mining industry to economic activity in these areas, as well as of the multiplier effect of secondary industries.

Jan 1, 1993

By E. Yan

Electrostatic separation has been a mainstay of minerals sands flowsheets for over 50 years. Recent electrostatic developments have shown better conductor/non-conductor separation than technology previously available. Results to date show significantly increased separation efficiency over prior-art high-tension roll electrostatic separator (HTR). These improvements allow greater simplification of MSP circuits by minimizing re-circulating loads. The distinct features of the eForce include: 1) A provision that minimizes the affects of particle size to improve separator performance, 2) an enhancement of the design and arrangement of the static electrode providing a greater attraction force for separating fine conductive particles, and 3) inner roll and outer plate electrode configuration to improve separation efficiency and throughput capacity. Key Words: eForce, Electrostatic, Ion bombardment, HTR, Separation Efficiency, Electrostatic Classifier

Jan 1, 2003

By D. W. Dean, J. A. Ryder

"A computer system designed to assist in maintenance scheduling and costing, and in monitoring the performance of equipment, is described. The emphasis is on the information retrieval and implementation aspects of the system.INTRODUCTIONThe cost of the maintenance of equipment can account for a substantial proportion of the total costs of any large industry. These costs are made up of the following elements:(i) capital expenditure,(ii) maintenance labour,(iii) maintenance spares,(iv) maintenance overheads,(v) production losses.Control of these cost elements cannot be achieved without a system which maintains and retrieves the necessary infor¬mation efficiently.The system should provide engineering management with the information necessary to:(i) establish the cost of maintaining items of equipment,(ii)establish the economic life of equipment,(iii) determine breakdown patterns for the establishment of optimum inspection, service and overhaul frequencies,(iv) establish work schedules for those responsible for the maintenance of equipment,(v) establish the optimum maintenance labour complement,(vi) establish the optimum stockholding of maintenance stores items,(vii) improve the performance of equipment,(viii) justify the selection of a particular type and make of equipment,(ix) establish the reasons for any abnormal usage of materials and labour, and to(x)reduce the dependence on the human element for the control of equipment maintenance activities.Many industries have comprehensive and numerous equipment maintenance records but they experience great difficulty in retrieving the required information in the time available and with the labour available. Many industries do not bother to maintain meaningful records, because of this difficulty."

Jan 1, 2014

The following contributions were received to the paper entitled 'Safety in South African mines: An analysis of accident statistics', by H.S. Eisner and J.P. Leger, which appeared in the J. S. Afr. Inst. Min. Metal., vol. 88, no. 1, Jan. 1988, pp. 1-7. Contribution by H. WAGNER* The paper by Dr H.S. Eisner and Mr J.P. Leger is critical of the safety situation on South African mines and portrays the industry as having little concern for the health and safety of its workers. Moreover, the casual reader gains the impression of deliberate misinformation by the industry to the public concerning safety maters. Furthermore, certain socio-economic reasons are advanced for the apparent differences between the fatality and injury rates reported for coal mines in South Africa and those for the United Kingdom. Contribution by S.A. WATTS. Authors Eisner and Leger are to be commended on their paper, which highlights, according to their interpretation, various shortcomings of both the Chamber of Mines accident statistics and those published by the Department of Mineral and Energy Affairs. Authors' Reply We gratefully acknowledge Dr Wagner's contribution to the discussion on our paper. For convenience, we shal use his sequence of comments in our reply. Before doing so, however, it may be useful to explain how our paper came to be written. After the explosion at Hlobane Colliery in 1983, one of us (HSE), in February 1984, was retained by the lawyers acting for some of the dependants of the victims to advise on technical maters relating to the explosion. Contribution by Ms S.A. Wats Some of the points made by Ms Wats have already been answered in our comments on Dr Wagner's contribution. We are fully aware that the number of accidents leading to absences of less than 4 days would be much greater than shown in our bar chart, and are grateful to Ms Wats for drawing attention to the specific exceptions that can make a 1-3 day accident compensable and that are clearly responsible for the relatively low count in that category of the chart.

Jan 1, 1988

By H. Ruthert

An understanding of wear in systems conveying solids is extremely important from the standpoints of design and economics. The lifetime of any bulk solids-handling system depends on the type of solids present and the operating parameters of the transportation system. The relationship between wear in backfill pipelines on South African gold mines and the transportation system's operating parameters is well understood. However, the effect of the transported solids on the pipe wear is less well understood, because of an inability to characterize particle sharpness. The sharpness of the particles, together with their size and hardness, is responsible for the aggressivity of particles, or their ability to cause damage and wear. This paper presents a novel method for the characterization of particle sharpness. The results presented rank particles according to the sharpness of their surfaces.

Jan 1, 1993

By P. W. Lotz

Traditionally, bottle roll tests have been used to optimize the extraction process for best gold extraction and recovery. Such tests typically involve exposing the ore to defined reagent concentrations (lime, cyanide and sufficient oxygen) and balance the gold input with recoveries and losses. With mounting pressures to accommodate sustainability issues during development work, it became apparent that much more information would be required on the interactions and kinetic behaviour of solid and solution species during the entire leach process. This information is vital to enable proactive management of critical issues such as cyanide, arsenic, water and tailings management. Inadequate management of these aspects has led to temporary closures and, in cases of non-compliance, to the dynamically changing regulations. MINTEK?s advanced leach facility (ALF) is being developed with the aim of bridging the knowledge gap between the gold leach process and the predictable environmental impacts upon discharge. The facility aims to monitor all parameters of relevance such as pH, Eh, dissolved oxygen, metals, cyanide species, and viscosity during the entire process to enable more informed decisions on practical interventions. The presented set of data reflects first experiences gained from processing a refractory gold ore concentrate. Attempts at optimizing the process were limited due to the developmental nature of the work. Data relating to leaches with differing preoxidation conditions and cyanide staging is presented.

Jan 1, 2009

Beatrix Gold Mine, a deep-level gold mine in the Free State province of South Africa, has the highest methane emission rate of any gold mine in the country. Methane is emitted from underground sources intersected during mining operations and is liberated into the general mine atmosphere. The total methane emission rate for the mine is of the order of 16001/s and the South section of the mine emits approximately 10001/s of methane gas. The mine has a history of gas accumulations which have led to a number of underground explosions. Following the last explosion in 2001 and the subsequent investigation, a number of recommendations were made. Two of these were to consider extracting the underground mine methane to render the mine atmosphere safe, and to declare hazardous locations that require special operating procedures. A number of such workplaces have now been declared at the South section of the mine. Methane gas is a potent, explosive greenhouse gas whose contribution to global warming and climate change is 21 times higher than that of carbon dioxide. To reduce its inherent danger and to mitigate its global warming impact, a carbon credit project under the Clean Development Mechanism (CDM) of the Kyoto Protocol has been developed and implemented, the aim being to capture and destroy the methane at Beatrix mine. The mine has constructed an extraction system to capture and extract 400 (Is of the methane. Percentage methane (per volume) of the gas intersected at source is 85%, with negligible concentrations of other hydrocarbons and water associated. The mine contracted the services of Group Five to design and construct the flare and ancillary equipment on surface, and Promethium Carbon was contracted to assist with the carbon¬-related aspects, approval framework, and administration of the project. A number of design and construction challenges had to be faced to extract and transport the gas effectively to the surface of the mine as the emitters are approximately 3 600 m away from the mine shaft at a depth of 860 m. Further considerations were the requirements for the type of column to be used to transport the methane gas, the pressure loss over the system, the safety systems needed to address the risk factors involved in the transport of the methane gas, and a suitable pumping system to extract the gas to the surface. The system operates under negative pressure provided by two blowers on surface delivering the emissions to a flare capable of burning off 450 8/s of methane gas. In this paper a number of benefits for the mine are discussed. These include, but are not limited to, the removal of approximately 55% of the total volume of methane gas from the general body of the air in the geographical areas of the mine where the methane gas is emitted into the atmosphere, and reducing the risk of methane-related incidents. A further benefit of this project is the mitigation of the global warming impact of the methane gas and the reduction of the mine's carbon footprint by approximately 25%. This project could also assist in alleviating the energy shortage being experienced in South Africa by means of the planned generation of 4 MW of electrical power, utilizing the methane gas, as a second phase of the project.

Jan 1, 2011

By M. McChesney

Modern materials for underground support* by M. McChesney The properties required of a support material for underground tunnels are discussed and, because concrete is both economical and easy to apply, a number of new reinforcing materials for concrete are examined with particular reference to these properties. From about thirty tests on different types of reinforced concrete, it is concluded that the addition of polymer to a concrete does not seem to influence the concrete's post-failure behaviour, and the on'y benefit to be achieved by this addition is to increase its flexibility (or to decrease it, depending on the polymer). Steel fibres tend to increase both the strength and stiffness of the concrete, but polypropylene fibres, although having definite loadcarrying capacities, provide non-stable failure, also known as brittle failure. The best result was obtained for concrete reinforced with steel wire: the post-cracking strength was very good and was maintained for a considerable deformation.

Jan 12, 1976

The visit which took place on the 18th February, 1972 was a departure in that the places visited had no direct connection with the work in which members of the Institute are normally engaged. It was refreshing and stimulating to see important and involved operations normally outside ones own trend of life and to have experts to speak about technical, financial and matters of general interest concerning their work, not forgetting their troubles and problems and how they overcame them. Carlton Centre The members of the Institute were received by Mr D. Appleton, Public Relations Officer of the Carlton Centre Limited, who introduced Mr L. R. M. Fee of W. Rhodes Harrison, Architect in charge of the project; Mr W. C. E. Skilton of Murray and Roberts, the Engineer in charge of the construction of the complex and Mr A. Home the Senior Operating Engineer of Carlton Centre Limited. Each of these gentlemen addressed the members giving short rundowns on the project with special reference to their particular sphere of the undertaking. A variety of particularly interesting statistics relating to the planning construction and the ultimate operation and maintenance of the complex was given. Mining engineers present had an opportunity to compare the problems encountered by them associated with depth to problems encountered by the civil engineer in the construction of a building rising to such an enormous height. To some of the members a sense of similarity of the labour problems encountered must have been recognised. After tea the visitors were divided into groups, each under the guidance of an official, and then visited the highest floor accessible and thereafter the 19th floor where the internal arrangements for airconditioning, lighting, plumbing, power supply and communication arrangements were explained. Thereafter a visit to one of the seven basements which houses all machinery required to serve this enormous complex enabled the visitors to see the standby power arrangements as well as the refrigeration plant. The visit finished in time to proceed to the Crest Hotel in Hillbrow for lunch. To our hosts for the visit to the Carlton Complex a special vote of thanks is recorded. Strydom Tower In the afternoon the party proceeded to the Strydom Tower where Mr Knight from the Public Works Department who was the Engineer in charge of the construction of the tower gave details on the construction and the extraordinary methods which had to be adopted to achieve the desired objectives and to overcome known as well as unforeseen difficulties. The comparatively short time taken to complete the project and the good safety record appeared to impress the visitors. The final phase of the visit was taken care of by Mr Bothma of Telecommunications Department of the Post Office, who gave an extremely interesting explanation of the telecommunication organization of the Post Office with particular reference to the part the Hillbrow Tower plays in the South African telecommunication system. Both gentlemen answered many questions willingly and interestingly. Following the explanatory talks the visitors were shown the technical equipment housed in the two top levels of the tower. Short explanatory talks gave members an insight into the workings of one of the most important aspects of modern life. Even to the amateur photographer opportunities existed to view and photograph the city from the highest available observation point. We are indebted to Mr Gouws, the Regional Director of the Post Office for granting permission to visit sections of the tower normally not accessible to the general public and to our hosts for the manner in which we were received and entertained on the explanation of the many interesting features of this important installation. In conclusion, the programme for the day can be classified as interesting, of exceptional educational value, and an opportunity to see something of the engineering skills put into two vast and ambitious undertakings and the results achieved.