Search Documents

The distribution of chrome spinels in a magnetically fractionated ilmenite concentrate sourced from the Murray Basin was characterized by XRF assaying, quantitative electron microprobeanalysis, grain mapping, automated mineral phase clustering, and modal analysis. At least 14 distinct chrome spinel types were present in the concentrate. There is considerable variation in the amount of each chrome spinel type present, although a high-Mg, high-Al phase makes up close to 45 per cent of the total spinel population. Magnetic fractionation results showed significant variation in the composition and relative abundance of spinels reporting to each fraction. Low magnetic field strength fractions (ie. high susceptibility grains) were dominated by chrome spinels that are mid-range in Al and Cr. These spinels have the highest magnetite, ulvospinel and Fe(Al,Cr)2O4components. In comparison, the high field strength fractions (i.e. low susceptibility grains) have the majority of the grains with high-Al contents indicating a higher proportion of Mg(Al,Cr)2O4component. Spinels high in a (Al,Cr)2.67O4non-stoichiometriccomponent are absent at low field strengths but tend to be concentrated in the high field strength, non-magnetic fractions. Intermediate field strength fractions tend to exhibit a broad spread in spinel compositional types. A mild roast treatment of the sample had no clear effect on the distribution of chrome spinels between different magnetic fractions, but it did cause a change in the magnetic properties of the accompanying ilmenite grains. The effect of more extreme roasting conditions on the magnetic properties of the chrome spinels is to be determined.

Jan 1, 2003

By S. M. Spottiswoode, Linzer. L. M.

We report on further progress in improving seismic locations by using the so-called double-difference method (Spottiswoode and Milev, 1998 and Waldhauser et al., 1999). Double-differences are obtained either using picked arrival times or various measures of time differences obtained from waveform pairs. The double-difference method provides for much improved relative locations by reducing the effect of the errors in the wave velocity of ray paths between each event and each geophone. Further improvements are obtained by using known locations, such as blasts. One of the difficult problems that we have overcome is that of finding the best “weights” for the time corrections. Experience obtained in relative moment tensor inversions by Andersen (2001) suggests that use of median corrections is both more stable and more accurate, even while the locations of the individual events is based on weighted least-squares minimization. A hybrid location program with known reference events has been developed. Tests on a synthetic data set gave relative locations that were much less widely spread than the absolute locations. The use of known event coordinates (blasts) moved the relative locations back towards the real locations. These results are confirmed in preliminary analysis of data from a mine. The absolute locations are adjusted using blast events restricted to the line of tunnel development. Inter-event distances are distributed in a power-law fashion that suggests that the relative location accuracies are improved by a factor of three or more. Nous rendons compte des progrès faits dans l’amélioration des locations de séismes en utilisant la méthode appelée de double- différence (Spottiswoode and Milev, 1998 et Waldhauser et al., 1999). On obtient les double-différences soit en utilisant des temps d’arrivée choisis soit des mesures variées de différences de temps obtenues de doublets de forme d’onde. La méthode de double-différence fournit des locations relatives très améliorées en réduisant l’effet des erreurs dans la vitesse d’onde des trajectoires de rayon entre chaque évènement et chaque géophone. D’autres améliorations sont obtenues en utilisant des locations connues, telles que les coups de mine. Un des problèmes difficiles que nous avons surmontés est celui de trouver les meilleurs coefficients de pondération pour les corrections de temps. L’expérience obtenue dans des inversions de phases tensorielles relatives par Andersen (2001) suggère que l’utilisation de corrections médianes est à la fois plus stable et plus exacte, même lorsque la location des évènements individuels est basée sur minimisation pondérée de moindres carrés. Nous avons développé un programme hybride de location avec des évènements connus pour référence. Des tests sur des données artificielles ont donné des locations relatives qui étaient beaucoup moins étendues que les locations absolues. L’utilisation de coordonnées d’évènements connus (coups de mine) a ramené les locations relatives vers les locations réelles. L’analyse préliminaire des données d’une mine a confirmé ces résultats. Les locations absolues sont ajustées en utilisant des évènements de coup de mine restreints à la ligne du développement du tunnel. Les distances entre chaque évènement sont distribuées comme par loi exponentielle ce qui suggère que les degrés d’exactitude des locations relatives sont améliorés par un facteur de trois ou plus. Wir berichten über einen weiteren Fortschritt, die seismische Positionen unter Verwendung der zu sogenannten Doppel-Unterschied-Methode (Spottiswoode und Milev, 1998 und Waldhauser et al.,1999) zu verbessern. Doppel-Unterschiede werden entweder mit ausgewählten Ankunftszeiten oder verschiedenen Messungen von Zeitunterschieden erreicht, die von den Wellenformpaaren erhalten werden. Die Doppel-Unterschied-Methode liefert viel verbesserte relative Positionen unter Verringerung der Auswirkung von Fehlern in der Wellengeschwindigkeit von Strahlengängen zwischen jedem Fall und jedem Geophon. Weitere Verbesserungen werden erreicht, indem man bekannte Positionen, wie Sprengungen verwendet. Eines der schwierigen Probleme, die wir überwunden haben, ist jenes des Findens der besten "Gewichte" für die Zeitkorrekturen. Die Erfahrung, die in den relativen Momentspannerumkehrungen von Andersen (2001) gewonnen werden bietet den Schluß an, daß der Gebrauch von mittleren Korrekturen beständiger und genauer ist, sogar wenn die Positionen der einzelnen Fälle auf der bewerteten Reduzierung der Methode der kleinsten Quadrate basiert. Ein hybrides Positionsprogramm mit bekannten Bezugsfällen ist entwickelt worden. Tests auf einem synthetischen Dataset gaben relative Positionen, die viel weniger weit gestreut waren als die absoluten Positionen. Der Gebrauch von bekannten Fallkoordinaten (Sprengungen) schob die

Jan 1, 2003

By C. Haberfield, J. Szymakowski

Recent studies by the authors into the behaviour of jointed rock masses using direct shear testing have confirmed that joint spacing has a significant effect on rock mass strength. The rock mass failure envelopes assessed from these tests have been compared to failure envelopes obtained using the Hoek-Brown GSI criterion. Good agreement between measured and estimated GSI strength envelopes where obtained when joint spacing was considered in the assessment of GSI. Les études récentes conduites par les auteurs sur le comportement des joints rocheux employant l'essai direct de cisaillement ont confirmé que l'espacement a un effet significatif sur la force de la masse rocheuse. Les enveloppes de ruptures obtenues pour ces essais ont été comparées à l'enveloppe de rupture obtenue en utilisant le critère GSI Hoek-Brown. Une bonne corrélation a été constatée entre les enveloppes obtenues expérimentalement et les enveloppes calculées par la méthode GSI quand l'espacement des joints a été pris en considération dans l'évaluation de GSI. Kuerzliche Untersuchungen der Autoren betreffs Reaktionen von gebrochenen Felsmassen zu direkter Scherkraft, bestaetigen, dass die Abstaende von Rissen einen deutlichen Einfluss auf den Widerstand der Felsmassen hat. Die Bruchbereiche der Felsmassen die von diesen Untersuchungen entwickelt wurden, wurden verglichen mit den Bruchbereichen, die man mit der Anwendund der Hoek-Brown GSI Formulierung erhaelt. Eine gute Uebereinstimmung zwischen gemessenen und errechneten GSI Festigkeitsbereichen wurde erzielt, wenn der Abstand der Risse in der Berechnung der GSI in Betracht gezogen wurde.

Jan 1, 2003

By T. Ertekin, X. Dong

This paper identifies the need for the development of specialized inverse solution techniques for the analysis of pressure transient data for the characterization of the transport and sorption properties of coal seams. Central to the proposed inverse solution technique is a specially structured artificial neural network (ANN). The most important transport and sorption characteristics of coal seams are butt and face cleat permeabilities, macropore porosity, Langmuir volume constant, Langmuir pressure constant, and sorption time constant. Conventional methods, such as type curve matching techniques and laboratory-derived measurements are handicapped in terms of being representative over the entire domain of interest. In this paper, we utilize analytical forward solution techniques for various combinations of characteristics of coal seams to generate training and testing patterns. These training patterns are shown to an ANN structured to learn the ubiquitous non-linear relationships that exist between coal seam properties, input conditions and the pressure transients measured. The trained networks are then extensively tested to ensure that they have effectively learned the training patterns. In the final stage of the development, the networks are run in the prediction mode. The responses of the networks are found to be in agreement with the input data. The developed networks are able to generate results generally within 5% error margin for permeability and porosity and 20% error margin for the sorption characteristics of coal seams. A number of examples highlighting the capabilities and degree of effectiveness of the network in characterizing the coal seams areincluded. Keywords: artificial neural networks (ANNs); coal seam characteristics; pressure transient analysis

Jan 1, 2003

By W. Zhu

ABSTRACT: This paper presents further developments of the principle of Construction Process Mechanics of rockmasses, The principle of loading variations analyses in space-time is systematically described. To demonstrate the applicability of the theory and method, the effect of the construction process of two practical engineering cases are analysed. ZUSAMMENFASSUNG: Das Mechaniksprinzip vom Konstruktionsprozess des Massenfels wird in diesem Aufsatz weiter Entwickelt.. Das Prinzip von Variationsladungsanalyse mit dem Zeit-Raumseffekt wird systematisch erklaert. Um die Anwendungsmoeglichkeit der Theorie und der Methode zu anschaulich darstellen, das Mechanikseffekt des Konstruktionsprozess wird fuer zwei praktische Anwendungsbeispielen zergliedert. : RESUME: Dans ce papier le development se fait pour principles de la mechanique de process de construction . Le principle de variable analyse considerant effet de temps et de Space est present ´e . Pour demonstrer l´appilicabilite de le theorie et la methode , l´èffect de processe de construction pour ce deax examples sont analysés .

Jan 1, 2003

By S. Carter

this paper describes an innovation in computer software that permits mining professionals to collaborate on exploration and mining projects regardless of geographic location. Growth of mining companies through merger and acquisition has created a greater need for mining professionals to collaborate, especially as projects and project participants are becoming geographically remote. Surpac NetVision, the name given to this new collaboration technology, satisfies this need by deploying interactive 3D graphics sessions across computer networks. It achieves this by using common web browser technology as the deployment medium. A plug-in architecture that supports diverse file formats permits transparent read and write of foreign data to further enhance the collaboration process. Surpac NetVision supports any number of connections from web browsers on remote computers using existing networks. Software components required to enable the collaboration session are deployed to the remote computer as required and cached for future sessions. The collaboration session at each computer is characterized by a fully functional replica of the user interface for Surpac NetVision from which any function can be executed by any client, at the owners discretion. All geometry and display attributes deployed to remote clients to render 3Dgraphics are highly compressed to reduce bandwidth requirements. The key benefits of this collaboration technology is improved communication in regard to exploration and mining projects leading to: •More informed decision making •Improved deployment of project objectives and plans beyond the technical planning group to project management and operations staff •Improved technical support for software users. Keywords: 3D graphics, project collaboration, interactive graphics, internet 3D graphics, mining software

Jan 1, 2003

By Y. Y. Jiao, J. G. Cai

To investigate the dimensional effect on shock wave propagation in jointed rock masses, a 2-D and a 3-D calculation of a site test are performed respectively by using Discrete Element Method, the simulated results are compared with test data. It shows that, in modelling shock wave propagation and attenuation in jointed rock masses, when the explosive along explosion chamber is long enough and the joints are dense enough or uniformly distributed, the model can be considered as plane-strain problem, 2-D results are good enough to fit with test data. 2-D modelling, with much more details of rock masses taken into account, can be applied to make critical engineering judgements instead of 3-D modelling in some cases.

Jan 1, 2003

By K. Coleman, C. Visser, N. Selby, X. W. Pan, T. Letwaba

A prototype weightometer soft sensor is under development at DebTech, De Beers in partnership with Venetia Mine. Its main function consists of an online data source; data validation; dynamic weightometer models; online detection of weightometer failure; alarming and replacing a weightometer when it fails. 31 dynamic models have been developed. All models with R2>= 85%are accepted as good models and they generally have satisfactory results with a daily error of less than 8% within 90% confidence level. By using those models, a set of soft sensors can be set up to cover all weightometers in the entire processes starting from primary crushing to the stock piles of dense medium separation (DMS). Some practical issues and concerns on model development are discussed, including data collection, data analysis, data pre-processing, variable selection, time delay, model training and model validation. When deploying the weightometer soft sensor system, the potential benefits could include: reduction in plant downtime; reduction in unplanned maintenance and even replacement of non-critical weightometers, particularly where nuclear weightometers are used. Keywords: soft sensor, weightometer, dynamic modelling, neural network modelling

Jan 1, 2003

A comprehensive review of ore pass records, from ten Quebec underground mines, indicated some of the limitations of available design tools to predict the occurrence of ore pass interlocking hang-ups in metal mines. The Distinct Element Method was used to perform a series of numerical experiments in order to investigate the influence of ore pass geometry, rock fragments shape and size distribution on material flow in an ore pass. Guidelines have been developed to help limit the occurrence of interlocking hang-ups in an ore pass. The proposed guidelines were evaluated with respect to field observations. Ein kompletter Bericht der Erzrollezeichnungen, von 10 Quebec unterirdischen Gruben, hat einige der Beschränkungen der vorhandenen Designwerkzeuge angezeigt, um das Auftreten Erzrolle der blockierenhang-ups in den Metallgruben genau vorauszusagen. Eine Reihe numerische Experimente mit der eindeutigen Element-Methode, wurden aufgenommen, um den Einfluss von Erzrollegeometrie, Partikelform nachzuforschen und Felsenkorngrößenverteilungen auf Materialfluss in ein Erz überschreiten. Dieses hat zu die Entwicklung der Richtlinien geführt deren Implementierung das Auftreten der blockierenhang-ups in eine Erzrolle begrenzen sollte. Die vorgeschlagenen Richtlinien wurden in Bezug auf Labor- und Feldbeobachtungen ausgewertet. Une revue de la performance actuelle des cheminées à minerai dans 10 mines souterraines du Québec a indiqué les limites des outils de conception servant à dimensionner les cheminées pour minimiser le nombre d’accrochages par enchevêtrement rocheux. Des séries de modélisations numériques, utilisant la méthode des éléments distincts, ont été réalisées afin d’évaluer l’influence de la géométrie des cheminées, de la forme des fragments rocheux et de la distribution granulométrique sur l’écoulement du matériel dans les cheminées. Cet exercice a permis de développer des lignes directrices pour le dimensionnement des cheminées afin de limiter l’occurrence d’accrochage par enchevêtrement rocheux. Les lignes directrices proposées ont été évaluées en fonction des observations effectuées sur le terrain.

Jan 1, 2003

By R. C. W. Webber

Mining up to depths of 5 000 m would be a world first and, accordingly, no previous experience in the determination of acceptable heat stress limits, criteria or indices is wholly applicable. However, some South African gold mines are already operating at depths beyond 3000 m and much of the knowledge gained in reaching and working at such depths will be helpful in making adequate provision for acceptable environmental control at the greater depths being contemplated. Accordingly, it is necessary to take cognisance of the industry?s experience in deep-level mining and of standards and regulations already established in South Africa and elsewhere in order to ensure acceptable working conditions and control standards, that compare favourably and defensibly with those in other mining industries. The local and international use of heat stress limits, criteria and indices were investigated as it was necessary to determine to what extent any other indices, limits or criteria would be applicable to South African deep mine conditions. In addition, it was necessary to establish whether there was a single heat stress index that could be used for South African ultra deep mining conditions. It was found that an appropriate combination of heat stress indices would be required in planning for and ultimately controlling thermal conditions in ultra-deep mining. The depths being contemplated and the concomitant potential heat hazard present too great a risk for reliance on a single environmental component of heat stress, such as wet-bulb temperature at present in common use locally. The study recommends that a heat stress index, preferably Air Cooling Power (ACP), be used to design an ultra deep mine?s ventilation system and that wet-bulb temperature be used to monitor and control the system once it is implemented.

Jan 1, 2003

By M. Kuchta, A. Newman

LKAB’s Kiruna Mine, located above the Arctic Circle in northern Sweden, is the second-largest underground mine in the world today. The orebody is a world-class high-grade magnetite deposit, from which three raw ore products are extracted. We use mixed integer programming to determine a production schedule, i.e., which production blocks to mine, and when to start mining them, so as to minimize deviation from planned production quantities while adhering to the operational constraints of the mine. The resulting model contains thousands of binary variables and a commensurate number of constraints, precluding us from obtaining a schedule in a reasonable amount of time. We describe a method that builds on prior, related work, to expedite solution time. Keywords: underground mining, production planning, optimization, integer programming

Jan 1, 2003

By M. Ghoreychi, X. Daupley

ABSTRACT: The paper is devoted to two major aspects related to the abandonment of salt mines: 1)- Long-term risk associated with the mechanical instability of surface and its consequences for public security and properties. 2)- Long term dissolution and transport of salt resulting from its communication with groundwater. Basic characteristic features of salt deposits and mining methods are presented through the studies already undertaken on French mines. This analysis allows to identify major hazards encountered in different traditional salt mines and solution-mining cavities. In particular, the role of overburden (presence and thickness of salt layer in exploitation roof, presence of clayey rocks or hard rocks e.g. dolomite or anhydrite), presence of water-bearing strata and possibly natural brine levels, discontinuities, etc. are discussed. In the second part, the main features of mechanical behaviour of salt (creep, damage) as well as transfer processes of this material are presented. The influence of these aspects on the long term evolution of abandoned salt mines is then analysed. KEY WORDS: exploitation, abandonment, salt, mechanical, stability, transport, solution, brine. ZUSAMMENFASSUNG: Der Artikel bezieht sich auf zwei bedeutende Aspekte beim Salzabbau: 1)-Das langsfristige Risiko zur Bodenoberflächeunbeständigkeit und sein Einfluss über Mensch= und Gütersicherheit. 2)-Die langsfristige Auflösung und Beförderung des Salz beruhen sich auf Studien über französiche Bergbauen. Diese Analyse emöglicht es, die bedeutendesten Risiken in verschiedenen Salzgruben zu identifizieren, bzw. Traditionellen oder durch Auflösung abgebauten. Insbesondere wird die Rolle des Deckgebirges (Vorhandensein und Dicke von Salzschicht am Dach des Grube, Beisein von Tanlager oder hartem Gestein wie Bitterkalk oder Anhydrid), Beisein von wasserhaltigem Boden und/oder gesalzenen Wasserflächen, Trennflächen, usw… erötert. Im zweiten Teil werden die haupsächlichen Eigenschaften des Salzverhaltens (Kriechen und Beschädigung) beschrieben. Ihr Einfluss über das Verhalten von stillgelegten Bergwerken lässt sich analysieren. SCHLÜSSELWÖRTER: Bergwerksbetrieb, Stilllegung, Mechanik, Beständigkeit, Ausbreitung, Aussolung, Solewasser. RESUME: L’article est consacré à deux aspects majeurs liés à l’abandon d’exploitations de sel : 1)- Le risque d’une instabilité à long terme de la surface du sol et son incidence sur la sécurité des personnes et des biens. 2)- La dissolution à long terme et le transport de sel sous l’effet d’une communication avec des eaux souterraines. Les principales caractéristiques de gisements et d’exploitations de sel sont présentées en s’appuyant sur les études antérieures réalisées sur les exploitations en France. Cette analyse permet d’identifier les risques majeurs rencontrés dans différentes mines de sel traditionnelles ou exploitées par dissolution. En particulier, le rôle du recouvrement (présence et épaisseur d’un banc de sel au toit de l’exploitation, présence de terrains argileux ou de roches dures telles que la dolomie ou de l’anhydrite), présence de terrains aquifères ou de nappes salées éventuelles, discontinuités, etc. sont discutées. Dans la deuxième partie, les principaux traits du comportement mécanique du sel (fluage, endommagement) ainsi que les processus de transport de ce matériau sont présentés. L’influence de ces aspects sur le comportement à long terme d’exploitations abandonnées de sel est ensuite analysée. MOTS CLES: exploitation, abandon, mécanique, sel, stabilité, transport, dissolution, saumure.

Jan 1, 2003

By T. Struminski

The paper is aimed to assess the possibilities of usage of pyrometers and thermal cameras to study ventilation and environmental conditions in underground mines. Surface and underground thermovision tests were carried out in the Rudna mine and included channels and diffusers of some selected fan stations, shaft crest closures, engines of central fans and their instrumentation. The thermovision underground tests in the Rudna mine consisted of ventilation barriers, underground fans, temperature of rocks, ventilation machines, parts of belt-conveyors and electric machinery.

Jan 1, 2003

By K. Kotwica, P. Gospodarczyk, J. Sosnica, J. Pawlik, Z. Iwulski, K. Pawlik

The paper presents problems resulting from the mobile mining machines functioning and requirements concerning a machine control system, which controls successive operation stages of such machines. The problem is presenting on the example of a mobile hydraulic support to remove residual pillars in copper ore mines. The paper describes an algorithm and a flow chart to be followed when designing a supports control system. Design of control systems to ensure machine function under given circumstances is also presented.

Jan 1, 2003

By M. Lu, E. Broch

Abstract: The formation and mechanism of rock cavern roof arches are studied and effects of rockbolts reinforcement are evaluated. It is concluded that a self-supported roof arch may be formed by the excavation. To stabilize such a roof arch, fully grouted rockbolts are effective. Tensioned cable anchors may have a negative influence on the arch stability. Zusammenfassung: Die Formation und der Mechanismus von Deckenbögen in Bergkavernen wird studiert und der Effekt von Verstärkung mit Bergbolzen wird bewertet. Es wird festgestellt, dass die Exkavation einen selbst-stützenden / freitragenden Deckenbogen formen kann. Eingegossene Bergbolzen sind effektiv um einen solchen Deckenbogen zu stabilisieren. Spannkabel können unter Umständen eine negative Einwirkung auf die Stabilität des Bogens haben. Résumé: Le mécanisme et la formation de voûtes dans les cavernes rocheures sont étudiés et l'effet du renforcement par boulonnage est évalué. Nous arrivons à la conclusion qu'une voûte autosupportêe peut être formée par excavation. Des boulons entièrement scellés par coulis de bêton s'avèrent efficaces pour stabiliser de telles voûtes. Les tirants d'ancrage peuvent quant à eux nuire à la stabilité de la voûte.

Jan 1, 2003

By J. Gummer, M. Williams, S. J. Hawksworth

A common problem encountered in British coal mines is bearing failure on conveyor system idler rollers, which on occasions has led to fires. The UK Mines Inspectorate initiated a study of such failures to assess the potential for ignition of explosive atmospheres. As part of this study HSL have developed a system to measure the temperatures generated within the bearings during controlled failure. Temperatures are measured using both infrared thermal imaging and contact thermometry. The work to date has shown that temperatures well in excess of the auto-ignition temperature of methane can occur.

Jan 1, 2003

By D. J. Steynfaard

Sishen Iron Ore Mine is situated 280 km north-west of Kimberley in the Northern Cape Province of South Africa. The mine produces and sells high quality iron ore of various specifications to various national and international clients. The saleable product is derived from the blending and beneficiation of different types and qualities of hematite iron ore. This paper documents the new developments which were implemented (or are in the process of being implemented) on the mine in the long-term planning, medium-term planning, grade control and material tracking in the beneficiation plant with special attention being paid to the quality of the final, saleable product. The process starts with the long-term planning where the pit shell and pit optimization is determined by Whittle 4X. New developments include the introduction of a linear programming based scheduling system to enhance the long-term schedule generated by Whittle 4X. The LP route was decided on in order to take into account all the constraining factors of the final product that could not be configured in Whittle. To complement this the XPAC Auto Scheduler scheduling package was introduced to do the medium-term mine scheduling. This 18-month rolling plan includes cost parameters to enable the planner to extract a detailed operational budget from the scheduling while ensuring that production standards are maintained and grade constraints are met. The existing grade control system was enhanced with GPS capabilities and a computer system to do material tracking. The high precision GPS system introduced on the shovels allows for the accurate control of the loading procedures at the mining face. Because of the complicated geology and grade composition of blasting blocks it is imperative to accurately differentiate between different materials in the same blasting block and being able to excavate that with the loading equipment. The GPS system on the trucks allows for accurate location monitoring of dumping in order to keep track of specific material types. The state-of-the-art material tracking system developed for Sishen will enable the grade control officer to keep track and record various parameters of the material from its in situ position in the blasting blocks, through the crusher and onto different stockpiles, in various stages of the beneficiation process and onto the blending beds, into the dispatching trains and eventually into the ships for international distribution. These developments elevate the Sishen planning and grade control systems to a new level of service excellence from which management can obtain accurate and timely information on product status. It also enables Sishen to maximize resource utilization while still complying with the tough market constraints.

Jan 1, 2003

By A. M. Bryukhanov, A. G. Mnukhin

The report states accident rates for gassy/dusty coal mines represented as an ergatic system "man – machine - environment" with further analysis by the method of conditional probabilities. A coal mine has been analyzed with allowance for the attending personnel, equipment and environment as a sequence of events and states. Probabilities of operational states have been determined and prediction of mine behavior has been made on the basis of investigation findings for equipment and the personnel states, and analysis of the environment (i.e. mine and mining conditions). Utilization of expert estimation methods has been considered for determining major operational parameters of gassy/dusty mines. The importance of standardized values of permissible occupational risks (permissible probability of accident, PA) is demonstrated. It is also stated that a procedure is essential to determine these values, involving regular check-ups of the integral safety criterion at all mines and further development of customized recommendations for individual mines on efficient improvement of accident situations. Methodology to determine the assessment criteria has been developed and scientifically substantiated for permissible accident rates in hazardous industries.

Jan 1, 2003

By Xu H.

In recent years, the mineral applications dealing with more complex data in distributed environment have grown rapidly. Many mineral and mining organizations have to organize internally and globally distributed manufacturing and experiment sites, which share the roles of databases and other multi-services like software programs. Thus, there are commercial and technical pressures pushing the mineral software vendors to move their current service toward Web service. XML has gained wide acceptance for representing, storing and transferring structured data and documents of many kinds, especially in scientific communities. However, so far there is no such a Markup Language in mineral industry. A XML-based uniform encoding, which is called MineML(Mineral Markup Language), is proposed and developed in this project. The framework of the MineML specification is created. MineML will play the role as shared protocols within mineral domain for archiving, transferring the multi-nature data between the software packages on the desktop over the Internet and sharing the services between users at different sites. Inspired by MLA’s (Mineral Liberation Analyser, JKMRC, University of Queensland, Australia) Mineralogical Data Presentation Program, a proof-of-concept prototype of Web Service is developed here to validate and demonstrate the MineML specification. Certain strategies, specific technologies and tools are adopted to create such an environment. To accomplish that, a set of experimental MineML documents including correlated XML, XSD (schemas) and XSL(stylesheets) documents have been elaborated for archiving, presenting and transferring the mineralogical data information, with the persistence on flexibility and extensibility for generic mineral and mining data handling.

Jan 1, 2003

By J. W. Klokow, K. L. Riemer, R. I. L. Ferreira

As a result of the increased depth of mining in the South African gold mining industry mining induced seismicity is a severe problem. One of the strategies within the industry to contain the problem is to incorporate a system of regularly spaced stabilising pillars into mine layouts. At the Driefontein Gold Mine a system of closely spaced dip pillars is used to contain seismic energy emissions. Comparisons of seismic data for several mining clusters initially indicated a possible measure of success in the containment and occurrence of larger events. A detailed analysis of data over a 5-year period since the start of mining however, has revealed a delayed seismic response to the increasing strike spans. Significant changes marked by an increase in certain seismic variables have been observed at mining spans of between 100 to 120 meters and could be of significance to pillar spacing in the design of deep level mining layouts. La sismicité occasionnée par l’exploitation minière est un problème grave dans les mines profondes de l’industrie minière aurifère en Afrique du Sud. Une des stratégies utilisées dans l’industrie a été de maîtriser le problème en incorporant un système de piliers de stabilisation régulièrement espacés dans la disposition des mines. A la Driefontein Gold Mine, un système de piliers de pendage proches les uns des autres est utilisé pour contenir les émissions d’énergie sismique. Au début, des comparaisons de donnés sismiques pour plusieurs groupes d’extraction ont indiqué un succès possible dans la limitation et l’occurrence d’évènements sismiques. Cependant, une analyse détaillée des données sur une période de 5 années a révélé un délai entre la progression de l’extraction et une réponse sismique accrue. Des changements considérables dans les variables sismiques ont été observés dans des intervalles d’extraction entre 100 et 120 mètres, ce qui pourrait être significatif pour l’espacement des piliers dans la conception de la disposition des mines de fond. Resultierend aus den zunehmenden Tiefen des Bergbaus in der südafrikanischer Goldbergbauindustrie stellt sich die vom Bergbau hervorgerufene Seismizität als bedrohliches Problem dar. Es war eine der Strategien innerhalb der Industrie, das Problem dadurch einzudämmen, daß regelmäßig plazierte Stabilisierungspfeiler in den Bergbaulayouts inkorporiert wurden. In der Driefontein Gold Mine wird ein System von knapp aneinandergesetzten im Abfallbereich befindliche Pfeiler benutzt, um seismische Energieemissionen einzudämmen. Vergleiche der seismischen Daten für mehrere Bergbaugruppen zeigten anfangs ein mögliches Maß von Erfolg in der Eindämmung und im Auftreten von größeren Fällen an. Eine ausführliche Analyse von Daten über einen 5jährigen Zeitraum hat jedoch ergeben, daß eine Verzögerung zwischen der Progression des Bergbaus und einer erhöhten seismischen Reaktion besteht. Bedeutende Änderungen in den seismischen Variablen wurden an Bergbauspannen von 100 bis 120 Metern beobachtet und könnten für Abstandsbemessung von Pfeilern im Design des Tiefbergbaulayouts von Bedeutung sein.

Jan 1, 2003