Search Documents

By Robert M. Cox

A thorough geological engineering investigation is required before surface lands overlying abandoned underground mines can be safely recommended as building sites. The major problems confronting the geological engineer are assembling accurate geologic and mining information and developing an accurate rock mechanics model of the situation. A successful investigation requires a combination of technical expertise in rock mechanics and engineering geology tempered with practical engineering judgment. The results of a good study are not always favorable to the prospective builder.

Jan 1, 1975

By R. J. Sweigard, R. V. Ramani

Productive and beneficial use of reclaimed surface-mined land is a concern of industry, government, and the general public. A process has been developed that will aid mine planners and public planners in the evaluation of postmining land use potential. This process involves the application of site planning principles to surface-mined land in a way that ensures productive end use of reclaimed land. The process consists of 10 basic components and is iterative in nature. Termination of the process depends on the amount of data collected and the evaluation requirements of each mining site. The analysis centers around the economic, environmental, and social impacts of the alternative land use plans.

Jan 1, 1987

By Sheridan A. Glen

As the Federal government along with individual states continue to grapple with the job of refining a comprehensive energy policy, coal continually stands out as an energy source which heralds a combination of old and new capabilities like an energy planners prophecy, but which is plagued with serious environmental constraints. To determine what level of coal utilization is ultimately possible for states East of the Mississippi, whose high sulfur content coal presents the most paramount of challenges, one must consider product availability, via existing transportation modes, the developing industrial markets and the ability of coal to meet the challenge of becoming an environmentally acceptable fuel. Gasification is emerging as a form of utilization, which during the next twenty years stands a good chance of being able to meet the challenge of making coal an environmentally clean, easily transport-able and usable fuel. It can be argued that, of all the potential ways of utilizing high sulfur coal, coal gasification is perhaps the most expensive, the most financially risky and carries environmental liabilities of its own. Synthetic gas and oil markets will undeniably be a function of price and demand, which, for the purposes of this paper, I'm assuming will begin to merge in the late 1980's and into the 1990's. This is also presuming that public utility commissions will allow favorable price structure ruling so that gasified coal products can be rolled into their respective rate base, much the same as synthetic natural gas from petroleum by-products are currently being priced. The comparative economic markets of coal to gas pro-duct have plenty of time to mature. There is an approximate twelve-year lead time needed to bring coal gasification plants on line which will be able to compete in the market place for natural gas and oil customers.

Jan 1, 1977

By M. Kehnemuyi

The U.S. Department of Energy is charged, by federal law, with the responsibility for developing and implementing programs for long- term storage and terminal disposal of high- level radioactive wastes from both commercial and defense nuclear operations. Approximately 288,000 cubic meters of defense high-level wastes are currently in storage at the government's Hanford Reservation in the State of Washington, the Savannah River Plant in South Carolina, and the Idaho Chemical Processing Plant in Idaho (U.S. Department of Energy, 1980a). High-level wastes from commercial nuclear power production are stored in water pools or basins at various power plant sites. At the end of 1980, approximately 7.460 metric tons of uranium, contained within 28,300 fuel assemblies was in storage at various reactor basins. Although the present inventory of defense wastes are many times larger in volume and in total level of radioactivity than the commercial wastes, in the future, the latter will constitute a substantial quantity of wastes that will have to be disposed of. The present electric generating capactiy of nuclear power plants in the United States is 56.5 Gigawatts-electric (GWe). The amount of spent fuel that would be discharged and accumulated by the year 2000 from these operating reactors would be 38,000 metric tons. With a projected growth of the nuclear industry to 180 GWe in the year 2000, the amount of spent fuel accumulated at the turn of the century could reach 89,000 metric tons of uranium or approximately 318,000 assemblies. In any case, whether one postulates a no growth pattern or one where nuclear power provides its share in the country's electric generating capacity in the next two decades, a means for safe and environmentally accept- able disposal of high-level nuclear wastes must be found. Storage of commercial wastes in water basins, either at reactor (AR) sites or at away from reactor (AFR) sites, and storage of reprocessed defense wastes in surface or near surface tanks is a temporary solution and is not an alternative for permanent disposal.

Jan 1, 1981

By K. M. Kim

A site-specific blasting model has been developed for the Asarco Mission mine. The main inputs to the model are the in-situ block size (F80), the post-blast fragmentation (P80) and the intact tensile strength (To). The output from the model is the specific blast energy (ESE). Modern techniques are being used to obtain the input parameters for the site-specific blast fragmentation model. In particular, image processing software is used to obtain both the in-situ block size and the post-blast fragmentation, and the Schmidt hammer is used to obtain the tensile strength at numerous locations throughout the rock mass. An initial model was developed using five test shots in one area of the mine that contains Argillite and is relatively homogeneous. This also included calibrating Schmidt hammer readings against actual Brazilian tensile measurements. The model for Argillite will be updated as more tests are conducted, and the model will be extended to the other four primary rock types at the Asarco Mission mine.

Jan 1, 2011

By R. L. Loofbourow, Robert R. Miller

Deep, stable, unlined space promises secure, efficient, acceptable solutions to several current problems. With truly favorable conditions, it can be economic as well. The basic requirement is sufficient sound, tight rock at required depth. This and unusual surface requirements point to special testing. An objective is to describe conditions for planners, estimators and contracts. A first stage concept study needn't be prolonged but should overlook nothing significant. Although observations and tests on core are considered essential, time and expense can be cut by supplementing then with tests on walls of rotary or percussion holes. In some places initial drilling could be shallow.

Jan 1, 1981

By Norman D. Harte, George W. Holl

The development of the most important tool used in Site Testing is reviewed briefly and the application of the information gained is described. The operation of Site Testing and pregrouting of underground excavations is dealt with in detail. Practical experiences (and pitfalls into which the inexperienced might fall) are recorded. But for the application of Site Testing and grouting of shafts, tunnels and other excavations, vast areas of the present goldfields in South Africa would remain unexploitable.

Jan 1, 1981

By J. Kemeny, K. M. Kim

A site-specific blasting model has been developed for the Asarco Mission mine. The main inputs to the model are the in situ block size (F80), the post-blast fragmentation (P80) and the intact tensile strength (To). The output from the model is the specific blast energy (ESE). Modern techniques are being used to obtain the input parameters for the site-specific blast fragmentation model. In particular, image processing software is used to obtain both the in situ block size and the post-blast fragmentation, and the Schmidt hammer is used to obtain the tensile strength at numerous locations throughout the rock mass. An initial model was developed using five test shots in an area of the mine that contains argillite and is relatively homogeneous. This process also included calibrating Schmidt hammer readings against actual Brazilian tensile measurements. The model for argillite will be updated as more tests are conducted, and the model will be extended to the four other primary rock types at the Asarco Mission mine.

Jan 1, 2011

In order to analyze and quantify distinct environmental properties in the vicinity of sites, the Site-Specific Natural Resources Information System (SARIS) has been developed based on a Geographic Information System (GIS). SARIS is one of the fundamental databases of a collaborative research program aiming at the resource orientated analysis of metallic raw material flows with aluminum and copper serving as exemplary case studies. The spatial database incorporates all present production sites of ore extraction, refining and smelting. Environmental data for each location were derived from global digital survey data covering land cover, soils, morphology, climate, topography and population density. The main application of this database is the characterization of environmental safeguard objects, which may be affected by the activity of concern. This site-specific environmental impact assessment is used to determine the relevance of environmental issues based on the distribution pattern of sites in a global framework. The derived results are used to suggest a tailored indicator approach to measure progress and performance of industrial developments relative to the predetermined site-specific conditions.

Jan 1, 2003

By S. A. Shoop

Vibrations from thirty-seven blasts were monitored using three seismographs. Data analysis showed that square root, cube root, and site-specific scaling predicted ground motion with equal reliability. Imprecise prediction is caused by geologic and blast variability, particularly inaccurate delay times. Vibrations at some mines were consistently lower or higher than vibrations reported in the U.S. Bureau of Mines studies. Regulations based on USBM data could then be too conservative or lenient. Predominant vibration frequencies were generally less than 50 Hz, but several blasts had significant energy up to 125 Hz. In some cases energy was concentrated at frequencies corresponding to delay intervals.

Jan 1, 1983

By Matthew Horsnell

Greenbank Terotech is a member of the Halley & Mellowes Group of Companies and is accredited t AS3902. Greenbank has been involved within the wear resistant lining industry for over 20 years. Initially supplying cast Basalt piping systems through to the present day breakthroughs with SiTech cyclone linings. The challenge of finding the most cost effective cyclone lining has been a difficult process. Over the years many varieties of ceramics have come and gone. In particular within cyclone applications, many people have become disillusioned with the term "Ceramic." In practice, it was discovered that if a ceramic worked in one part of the plant, it did not necessarily work in the cyclone area. A good example of this is Alumina chute and pipe linings. An Alumina lined cyclone underflow bend would provide exceptional wear resistance, whereas an Alumina Spigot would have failed miserably. After Alumina's were tried, Silicon Carbides were experi­mented with. The results in many trials were mixed. What worked at one mine did not work at another. The results did not conclude decisively that ceramics were here to stay within the hard rock cyclone area. It was then that Greenbank Terotech started to look at the reason "Why do some linings work and others don't." We came to the conclusion that the matrix holding the particles together had to be the key to a successful cyclone material. At the time we looked at materials such as Alumina Bonded Silicon Carbides, Metallic (Aluminium) Bonded Silicon Carbide, 99% Alumina Ceramics and Nitride Bonded Silicon Carbides, but all these materials either suffered from chemical attack on the Aluminium matrix (via cyanide) or the matrix simply was not hard enough causing wear rates to be excessive. It was then we looked at SiTech. SiTech is a unique material in that the primary particles are Silicon Carbide, but the matrix is made up of a Secondary Silicon Carbide formed within the reaction bonding process.

Jan 1, 1995

By Steven G. Vick

Not too long ago a mill superintendent, when asked where his tailings were being disposed, could simply shrug his shoulders and point to the open end of the thickener discharge pipe. This “out of sight, out of mind” approach to tailings disposal is a practice of the past. Today there are very few planned hardrock or energy-related mining facilities where tailings disposal has not been identified as the major area of impact and controversy. In fact, development of some ore bodies has been stymied altogether by lack of suitable sites or methods for tailings disposal. The bottom- Iine result is that tailings disposal often controls the permitting lead time and has a significant influence on construction cost (up to 2070 in some cases) of new minemill complexes. The following article, the first in a series of three, explores technical background and historical perspectives on siting and design of tailings impoundment facilities.

Jan 6, 1981

By William G. Wilson

In the U.S. today a number of tentative synthetic fuel plants have been sited by a number of major corporations. Each of these for a number of reasons have deferred construction. The only synthetic fuel plants under active development are those being built with the Energy Research and Development Administration (ERDA) under the authority of the Non-nuclear Energy Research and Development Act of 1974 (Public Law 93-577). Under this Act in joint sponsorship with industry, a series of coal conversion pilot and demonstration plants are being built to produce environmentally acceptable fuels from high sulfur coals. Before entering into a discussion of the factors associated with the siting of the ERDA coal conversion program, the difference between a pilot plant and a demonstration plant should be explained. The terms pilot plant and demonstration plant iridicate a size of plant rahter than technology. A pilot plant will vary from an "add-on" to an existing facility to an independent unit. Demonstration plants are a wholly independent, self contained plants, capable of independent operation to demonstrate the environmenta1, economic, and technica1 feasibility of a technology. These plants are from one-third to one-tenth the scale of a commercial operation and often described as plus 1000 tons per day of coal consumption. Their purpose is stated in the Act (Section 6, (3)(E),) "to accelerate the commercial demonstration of technologies for producing syncrude and liquid petroleum products from coal: Provided. That the Administrator shall invite and consider proposals from potential participants based upon Federal assistants and participation through guaranteed prices or purchase of the products .... " In site selection and plant design it has been suggested that special interest groups should be allowed to dictate the site and specify the design. Under the present program the industrial partner who is contributing 50 percent

Jan 1, 1977

Coal preparation plant simulators are used to study flowsheet alternatives and determine product quality and quantity that can be produced under various operating conditions for individual circuits. Some simulators also provide an estimate of the cost per ton of clean coal by determining the number and size of different processing units required for a specific raw coal tonnage and by computing both capital and operating costs for individual units. However, to the authors? knowledge, none of these simulators have the ability to optimize plant performance while satisfying multiple product quality constraints and selecting the most profitable flowsheet from many alternatives. A novel coal preparation plant simulator (SIU-Sim) that maximizes the overall plant yield using a robust optimization tool and selects the best plant cleaning circuit configuration based on maximum plant profitability is presented. The simulator also identifies the best operating conditions for individual circuits of a plant to satisfy multiple quality constraints for the overall clean coal product. It uses a genetic algorithms- (GA) based technique to maximize the overall plant yield for each cleaning flowsheet alternative and uses a net present value (NPV) analysis technique to maximize plant profitability for the entire life of a new plant or the remaining life of an existing plant. The step-by-step development of the simulator along with a case study demonstrating its specific features is presented.

Jan 1, 2008

By O. R. Swendseid

The Mountain Con mine is a relatively old, deep mine located in Butte, Montana. Operations at this property through the present shaft were started before the turn of the century. As mining progressed to depth, increasing demand for ventilation facilities and changing mining conditions made it convenient to convert some nearby shafts to airways. The fact that these openings had not been originally planned for use as airways made it necessary in some instances to utilize long and inefficient already-estab¬lished entries to service working areas. This situation existed in the Lexington fresh air system. The Lexington system consists of a vertical, 3-compartment shaft extending from surface to the 3200 level and a series of 2-compartment air raises and old horizontal-haulage openings extending into a mining area several thousand feet west of the Lexington shaft between the 3900 level and the 4200 level. Because of restrictions and high resistance in the portion of the system between the bottom of the Lexington shaft on the 3200 and the mining area on the 3900, the capacity of this system is only 85,000 cubic feet of air per minute. It was calculated that the capacity of the system could be in¬creased to meet the demands of the current mining program in this section of the mine by utilizing a single, straight, horizontal air course on the 3200 and by driving an inclined air raise 740 feet long between the 3900 and the 3200.

Jan 1, 1967

Steven F. Leer, president and chief executive officer of Arch Coal Inc. will be the master of ceremonies for the 12th Annual National Mining Hall of Fame Induction Banquet. The black-tie (optional) affair will be held at the Adam’s Mark Hotel on Sunday, Oct. 10 in St. Louis, MO. Six legendary leaders will be inducted at the ceremony. They will join 145 mining greats previously honored in the annual ceremonies. R. Joe Wagner, vice president for exploration and chief geologist of The Doe Run Co., St. Louis, will be the evening’s keynote speaker. His father, Richard Edwin Wagner (1898-1979), was inducted into the National Mining Hall of Fame in 1998 at the banquet in Phoenix, AZ.

Jan 1, 1999

Historian and storyteller, Duane Smith, will be the keynote speaker at the National Mining Hall of Fame's 10th anniversary induction banquet on Saturday, Sept. 6,1997 in the Museum Convention Center at Leadville, CO.Smith is a professor of history and southwest studies at Fort Lewis College in Durango, CO. He is also an award-winning author of 28 books about the West and mining. Hall of Fame Board Chairman Richard Moolick said the induction banquet event will mark the National Mining Hall of Fame and Museum's 10th anniversary in its Leadville facility, a century-old Victorian schoolhouse. Karl Elers, chairman of Battle Mountain Gold in Houston, TX, will be the master of ceremonies. He is a member of the National Mining Hall of Fame and Museum's board of directors. The six inductees into the National Mining Hall of Fame will be enshrined by Thomas Falkie, president of Berwind Natural Resources of Philadelphia, PA. He is also chairman of the Mining Hall's board of governors. The six inductees will join 132 mining greats who were previously honored. The black-tie (optional) banquet will be highlighted this year by guests who prefer to don 1890s dress for the occasion in the old silver-mining boomtown. A cocktail reception and open house will precede the banquet, with tours of the district and special events to follow on Sun- day, Sept. 7.

Jan 1, 1997

The sixth annual conference of the Mineral Economics and Management Society (MEMS) was held Feb. 27 through March 1 in Boulder, CO. This year's event was attended by more than 100 academic, industrial, government and other professionals interested in mineral economics and materials management. With about 250 members worldwide, this not-for-profit society seeks to promote scientific and economic analysis of current relevant issues. This year's program was sponsored by Alcan, Bateman Engineering, Cyprus Amax Minerals, J.P Morgan, Knight Piesold LLC and Newmont Gold. The conference's technical program consisted of six sessions. These included "Financial tools for a changing world," "Access to minerals," "Comparing North and South America," "Environmental issues in today's world" and "Transporting minerals." The program was concluded with a panel discussion titled "National minerals policies in Asia." In addition, a student papers session was held, in which students were given the opportunity to compete for a $1,000 award. The following is a brief review of the technical pro¬gram.

Jan 1, 1997

By W. Blake, J. Whyatt

Sixty years of rock bursting in the Coeur d'Alene district has taught painful lessons and led to a number of practical advances in controlling rock-burst hazards. This paper summarizes these lessons, concentrating on practical measures that have been successfully adopted to reduce hazards. These lessons are explained in the context of district mining history and current understanding of rock-burst phenomena. Overall, the paper provides the practicing mine engineer with an appreciation of rock-burst hazards and an overview of practical measures that can be used to control these hazards in the context of Coeur d'Alene district experience.

Jan 1, 2003

By J. P. Matoney

In recent years, the diminishing supply of natural gas has led energy suppliers and consumers to consider making synthetic natural gas from coal. A number of processes have been devised to produce gas from coal; many of these have been operated at the pilot stage and some have been operated commercially. Each process has specific coal feed stock requirements with respect to size consist and moisture content. The purpose of this presentation is to compare the estimated costs for coal handling, live storage, size reduction and drying facilities that would be required for delivery of coal feedstock to different gasification processes.

Jan 1, 1977