Search Documents

By Andrew Griffiths

The emphasis in the title of this paper should be placed on the world "Total", since the detoxification of cyanide in its free and weakly-complexed form with H202 has already found application in many areas, including the treatment of mining effluents. One of the most common forms of cyanide found in gold-mill effluents is hexacyanoferrate (usually ferrocyanide), which is included in measurements of total cyanide but is too stable to be oxidized by H202 or any other conventional oxidizing agent. This has led to the view that H202 cannot be used to detoxify effluents containing hexacyanoferrates, when a limit has been set on total cyanide. A process is described in this paper which does meet this requirement, and which has already been demonstated in two Canadian gold mills. Before describing the new process, the terms "free", "total" and "weakly-complexed" cyanide will be defined as they are used in this paper.

Jan 1, 1998

By S. J. Stokowski

An extensive drilling and laboratory testing program indicates that diagenetic dolomitization of the Oligocene Sombrerito Fm. limestone, southwestern Dominican Republic, is detrimental to the usefulness and quality of the potential construction aggregate resource. The first part of this program was the collection, photographing, and geologic logging of diamond drill cores to allow lithologic subdivision of the strata into potential quarry layers. The primary lithostratigraphic units are: I (youngest) approximately 10 m of white, dense marine limestone; II, approximately 5 m of white, interbedded dense and chalky marine limestone; III, 2+ m of tan, chalky calcitic dolomite. Unit I has been often altered by lateritic weathering and/or dolomitization; Unit II is often altered by dolomitization. The quarry layers were individually crushed, by core, into coarse aggregate sizes for chemical and physical (specific gravity absorption, MgSO4 soundness, sand equivalent, and LA degradation) analyses. The non-weathered units decrease in coarse-aggregate yield and quality with depth and dolomitization. Dolomitization typically causes about 5% lower yield of coarse aggregate, a sand equivalent of about 20 units below the original value, an increase in absorption of about 3%, an increase in the LA of up to 13%, and a decrease in the average 5-cycle MgSO4 soundness by about 17%.

Jan 1, 1987

By T. E. Mccandless

Detrital minerals of mantle origin have been found in the Green River Basin of Southwestern Wyoming (Figure 1). Pyrope, pyrope-almandine, and chrome-bearing clinopyroxene and orthopyroxene occur on the antmounds of Pogonomyrmex Occidentalis. These antmounds are a common sight throughout the western U.S., and were used by early paleontologists as fossil mammal collection sites. The mound is composed of two types of material; (1) soil excavated during the digging of the nest below the surface (maximum depth 3 meters) and (2) larger grains collected from the surface and placed on the mound, probably to prevent erosion. The selection of grains to armor the mound seems to be based largely on the mean diameter of the grain, with other factors such as weight, sphericity, roundness and composition in decreasing order of importance (Wheeler and Wheeler, 1963). The minerals of this study happen to fall within that mean diameter range. The garnets are found on the mounds as 3-6 mm diameter subrounded to subangular grains. The pyroxenes are also 3-6 mm in diameter and are most commonly subangular laths. The minerals themselves show evidence of abrasion, such as frosted surfaces and rounded edges. Orange peel texture is present on some of the grains, which suggests that kelyphitic rims were once present, but have been removed. Also, no similar minerals were found in sieved soil auger samples to depths of 2 to 6 meters taken near the antmounds. These observations imply a distal rather than proximal source for the minerals. Lamproitic rocks of upper mantle origin are found bordering the "Green River Basin. The best known are the Leucite Hills, a series of ultrapotassic volcanics found on the north flank of the Rock Springs Uplift (Carmichael, 1967). Minor occurrences of mica peridotite and ultrapotassic volcanics are also found on the western end of the Uinta Mountains in Utah (Best, et al, 1968). None of these rocks are known to contain minerals like those on the antmounds. The garnets are comprised of purple chrome pyrope, red chrome pyrope-almandine, and pink to orange low chrome pyrope/pyrope-almandine. Oxide statistics for these groups are summarized in Table 1. These three groups are distinct when their Cr203 values are plotted against magnesium number (Figure 2). The chrome pyropes are highest in Cr203 (1.28-2.66%) and have high, restricted Mg number values (0.781-0.826). The chrome pyrope almandines have similarly high Cr203 (1.29-2.62%) but a lower Mg number range. The low chrome pyrope/pyrope-almandines have the lowest Cr203 content (0.09-0.73) and the widest Mg number range (0.534-0.836). Using the classification scheme of Dawson and Stephens (1975) the chrome pyropes are most similar to garnets derived from kimberlite and from garnet lherzolite, websterite, and harzburgite xenoliths in kimberlite. The chrome pyrope-almandines and the low chrome pyrope/ pyrope almandines are similar to garnets derived from eclogite nodules (Figure 3).

Jan 1, 1984

By E. Z. Manos

The Detroit salt mine is operated by the Detroit Salt Co. It is one of the oldest underground room-and-pillar mines in the United States still in production. Mining at the Detroit salt mine began in 1906 with the sinking of the No. 1 shaft. Mining continued through the years, becoming progressively more modern in its equipment and techniques, until it was closed in 1983. In 1997, after a period of care and maintenance, the newly formed Detroit Salt Co. decided to reopen the mine. Upon completion of an extensive rehabilitation program, salt production resumed in 1998. Production currently continues at a rate of 910kt/a (1 million stpy). To date, the Detroit salt mine has mined more than 45 Mt (50 million st).This mine is unique because it lies under a heavily urbanized area within metropolitan Detroit. The mine and its history make a good case study for the continuing coexistence between the mining industry and its environs.

Jan 1, 2003

By Shular R. Scudamore

There was a time when heavy-duty apron feeders were built to last almost forever. The machines were heavy and built to maintain certain expected longevity and reliability. Increasing emphasis on return on capital leads to cost-effective designs. Costs can be increased or decreased, depending on customer specifications and the design philosophy of the feeder manufacturer. Specifiers can make important contributions to cost effectiveness. To do so, this article describes what should be known about planning with a supplier for heavy-duty apron feeders. There are several factors that should be considered, including capacity, characteristics of material carried, length, method of feeder loading, degree of lift, hopper opening, pan construction, and type of drive. Today's apron feeders are built in various sizes and with a variety of components to handle heavy, lumpy, or abrasive materials that can ruin lighter feeders. Careful feeder selection is important if it is to provide a controlled feed rate, absorb huge impacts, be used with long hopper openings, and have a relatively low power-perton capacity. Variations in systems and materials demand that each feeder be designed for its application, drawing on a wide range of components. Therefore, certain factors must be considered before final specifications are drawn. Capacity The design and application of an apron feeder is based on how material passes through a given system over the feeder into processing machinery. The processing machinery's capacity governs other equipment and productivity of the flow. From this basic information, related sizes of upstream equipment can be determined. Of these, the apron feeder acts as the "mouth and neck of the bottle." No more will pass than the mouth and neck will accommodate. Everything in the apron feeder design, from dimensions to power, is based on processing machinery. Material Considerations Are Vital Just as the nature of materials to be crushed or screened affects capacity and productivity of a crusher or a grinding mill, so does it affect capacity and performance of a feeder. Lump size must be identified closely so the pan width can be selected to accommodate the maximum lump with room to spare. For example, a lump size of 760 mm (30 in.) indicates a pan width of 1.5 m (60 in.) While two times the maximum lump is considered minimum width, if the maximum lump

Jan 12, 1983

By David A. Brence, Andrew D. Marti, Richard P. Stahura, Ronald J. Valentine

The development of an effective belt-cleaning system for a new conveyor system seemed a fairly conventional assignment. But a closer examination of the project showed a number of “fine print” details: •High altitude location (with resulting cold weather and low humidity conditions). •Long conveyor length. •Troublesome material (very sticky and capable of hardening like concrete). •Limited water. These difficulties are spelled out the challenge of developing a cleaning system for the production conveyor2 (PC2) belt at Climax Molybdenum’s Henderson Mine.

Jan 1, 2005

By Pedro Pablo Vasquez Coronado, Victor Octavio Tenorio

"Productivity in openpit mines depends on the observation and adjustment of critical phases of operation. As one of the most expensive activities in openpit production, optimization of the load-haul-dump cycle becomes a critical aspect to address. Using simulation techniques and an ad hoc methodology for analyzing the key performance indicators (KPIs) involved in the production cycle, it is possible to compare actual performance and ideal operating conditions and develop an alert system when operating conditions are subpar with the expected production standards.Study objectivesThe purpose of this work is to implement a methodology for optimizing the haulage cycle by identifying and adjusting the factors that affect the cycle time performance. The methodology includes the implementation of an alert system emitting warning messages when one or several trucks are idle, or when the time of completing production tasks is falling outside a predefined value. This alert is compared with predefined KPIs and is used to determine corrective actions.The alert will:• Demonstrate the benefits of time analysis and how this affects the productivity results in the mining process.• Demonstrate the utility of KPIs in the extraction of ore and waste and how they help to identify equipment performance.• Develop software interfaces to visualize the alert system in order to increase awareness in the operations supervisor.• Make recommendations for future applications that can help improve the productive process of an openpit mine.Problem statementTransporting material in openpit mines may require the utilization of high capacity equipment, which also represents an elevated cost per hour. A supervisory system that controls the adequate distribution of trucks and shovels by providing the operational status of each unit shall contribute to increase productivity while subsequently reducing operational costs. Nevertheless, there is an issue with certain dead times such as queue trucks for loading, trucks waiting to be loaded and other delays. This creates inefficiencies in fuel consumption and energy utilization.For the identification of delays, a contextbased system could be required in order to help optimize the haulage cycle time by controlling delays in loading, haulage and dumping. After applying this methodology, efforts were focused in correcting out-of-standard performance values."

Jan 1, 2015

By V. O. Tenorio, P. P. V. Coronado

"INTRODUCTION Productivity in Open Pit mines depend on the observation and adjustment of critical phases of operation. As one of the most expensive activities in Open Pit production, optimization of the load-haul-dump cycle becomes a critical aspect to address. Using simulation techniques and an ad-hoc methodology for analyzing the Key Performance Indicators (KPIs) involved in the production cycle, it is possible compare actual performance and ideal operating conditions and develop an alert system when operating conditions are sub-par with the expected production standards. STUDY OBJECTIVES The purpose of this work is to implement a methodology for optimizing the haulage cycle by identifying and adjusting the factors that affect the cycle time performance. The methodology includes the implementation of an alert system emitting warning messages when one or several trucks are idle or the time of completing production tasks is falling outside a predefined value. This alert is compared with pre-defined Key Performance Indicators (KPIs) and determine corrective actions: • Demonstrate the benefits of time analysis and how this affects the productivity results in the mining process; • Demonstrate the utility of KPIs in the extraction of ore and waste, and how they help to identify equipment performance; • Develop software interfaces to visualize the Alert System in order to increase awareness in the operations supervisor; and • Make recommendations for future applications that can help improve the productive process of an Open Pit mine. PROBLEM STATEMENT Transporting material in Open Pit mines may require the utilization of high capacity equipment, which also represents an elevated cost per hour. A supervisory system that controls the adequate distribution of trucks and shovels by providing the operational status of each unit shall contribute to increase productivity and subsequently reducing operational costs. Nevertheless, there is an issue with certain dead times such as queue trucks for loading, trucks waiting to be loaded, and other delays. This creates inefficiencies in fuel consumption and energy utilization. For the identification of delays, a context-based system could be required in order to help optimizing the haulage cycle time by controlling delays in loading, haulage, and dumping. After applying this methodology, efforts were focused in correcting out-of-standard performance values."

Jan 1, 2016

By Dale R. Ralston, Roy E. Williams, Gerry V. Winter, George L. Bloomsburg

The purpose of this section is to demonstrate the development of a method that we believe can be used for simulating and predicting mine water inflow. It will also show how important it is for personnel who model mine water inflow to have considerable experience with this subject, and with the conversion of hydrogeologic frameworks to conceptual models. Several of the models described previously are said to be three dimensional. However, closer examination reveals that there is considerable limitation in the variation possible in the third dimension. A true three-dimensional analysis would require a very large program. Therefore, it seems more reasonable to develop a procedure by which information from a two-dimensional model can be used for analysis of a three-dimensional problem. For a vertical mine shaft this is relatively easy because most two-dimensional models have an option for axisymmetric flow. If it can be assumed that axisymmetry exists about the centerline of the shaft it can be modeled easily as has been illustrated previously. For a horizontal drift or tunnel the analysis is not nearly as straightforward. However, the flow can be divided into two parts as indicated in Fig. 59. Part 1 considers the flow into the side of the drift while part 2 considers the flow into the end of the drift. To calculate the flow rate into the entire drift from the unsteady flow into a unit length the instantaneous flow per unit length may be integrated over the total length of the shaft. This procedure is shown in Fig. 60. The radial flow through any incremental length of the shaft is q. The total flow rate, Q, into the drift at any particular time is given by: The discharge q is a function of the time during which a particular segment has been draining that is dependent on the location x. In other words, a location at x = 0 has been draining during the entire time of expansion while a segment at x = L has only started to drain. Therefore, the time of draining at any point, x, is given by: [ ] where t' is the time over which the mine has been expanded. To determine the relationship between q and t it is necessary to refer to Polubarinova- Kochina (1962, pp. 566-569) and the equation given for the unsteady flow problem. This is: [ ] where q is the steady flow, q,, q, are the coefficients, and t is the time since drainage began. The expressions for q0, q1, and q2 are given as:

Jan 1, 1986

By A. Shah, L. W. Saperstein, M. C. Radomsky, D. L. Passmore

The development of microcomputer software that provides an analysis of pit-specific accident and production data for the mining industry is seen as a vital component in a total loss-control system. The Mine Injury Reporting System (MIRS) allows users to access accident and production data prepared by the Health and Safety Technology Center of the Mine Safety and Health Administration of the US Department of Labor for any particular state and to generate a simple, yet informative, report.

Jan 1, 1990

By D. L. Passmore

The development of microcomputer software that provides an analysis of pit-specific accident and production data for the mining industry is seen as a vital component in a total loss-control system. The Mine Injury Reporting System (MIRS) allows users to access accident and production data prepared by the Health and Safety Technology Center of the Mine Safety and Health Administration of the United States Department of Labor for any particular state and to generate a simple, yet informative, report.

Jan 1, 1988

By J. Drew

Oregon Resources Corporation (ORC), an industrial minerals mining company, is currently engaged in the development of a new process design that will allow the unique paleo-beach placer deposits of southwestern Oregon to be mined efficiently and economically, creating an additional domestic source for chromite, garnet, and zircon. Engineering design has been guided by the variable geology and mineralogy of the paleo-beach placer deposits as well as the need for a dry tailing scheme that resolves a lack of water resources at the placer locations and at the same time eliminates the need for slurry settling ponds, typical of paleo-beach placer operations in North America. Metallurgical study of the placer material was grouped into four distinct samples based on marine terrace deposition, geological facies, and mineralogy. Because the metallurgical samples represented the extremes likely to be encountered in all future Oregon paleo-beach placer ores, the process design is highly dynamic and will successfully adjust to meet the production needs. Water availability at the mining area is seasonal and will not support a typical placer operation?s water requirement needs for heavy mineral concentration. For this reason, ORC has developed a plan to construct the ore processing facilities near Coos Bay, where a municipal source of water is available. Raw ore will be transported from the mining sites approximately twenty miles one way to the processing facility with return loads hauling tailings back to the active pit. The need to haul dry tailings, return dry material to the pit for reclamation, and limit the amount of water being purchased from the municipality has driven the design of a unique water reclamation system. BACKGROUND Location and Access Economic concentrations of ?black sand? or heavy mineral (minerals with specific gravity greater than 2.85) have been recognized and studied in marine placers from Coos Bay to the mouth of the Rogue River, a distance of approximately 75 miles along the southern Oregon coast (Hornor, 1918; Griggs, 1945)(Figure 1). ORC will begin mining existing reserves approximately 20 miles south of Coos Bay in a region known locally as Seven Devils. Ore will be trucked north to the processing site near Coos Bay via use of existing county and state roads, including U.S. 101. The available facilities at the processing site include highway, rail, municipal water and electricity, natural gas, and a deep water port. At the time of this writing, the rail line had been abandoned, but was being pursued by the International Port of Coos Bay. It is anticipated that this will be serviceable at some time in the future. History The southern Oregon marine placers have garnered the interests of miners since 1852, when present day beaches were exploited for gold. The beach deposits were small and irregular in nature and were easily washed away by the major storms the coast endures during the winter months (Hornor, 1918). [ ] In the 1920?s, deposits at the beach were followed upstream to their paleo-beach terrace origins (Pardee, 1934). These terrace placers were mined, but with little success, as the cost of mining and processing was greater than at the present day beach deposits. The greatest effort to understand and delineate the paleo-beach terrace placers came during World War II. As the need for a domestic source of steel hardening chromite was evident, the heavy mineral bearing placers of southwestern Oregon provided just that. The U.S. Geological Survey, under guidance from the Oregon Department of Geology and Mineral Industries, began exploration drilling of the paleo-beach terraces in 1940 (Griggs, 1945). This work was part of the investigation of strategic mineral deposits and would ultimately supply much needed chromite for the war efforts. The first mining efforts began in 1943 by the Humphreys Gold Corporation and the Krome Corporation (Griggs, 1945). Black sand

Jan 1, 2009

Many organisations, including those in the resources industry have Board-level endorsed principles on sustainability. A key challenge, however, is how to systematically integrate these high-level principles into the design and operation of mineral processing plants. In an effort to meet this challenge the Sustainable Operations framework, called SUSOP®, was conceived and developed through the Corporative Research Centre for Sustainable Resource Processing (CSRP) in Australia. Somewhat analogous to HAZOP (Hazard and Operability Studies) which is well entrenched in the resources industry, the key aim of SUSOP® is to produce a holistic, systematic and rigorous methodology for identifying and assessing sustainability opportunities and risks. This paper argues the need for such a sustainability framework, presents the key elements of SUSOP®, highlights how case studies enhanced its development and articulates the reasons why such a framework will have growing importance into the future.

Jan 1, 2011

By Amy McBrayer, Andrea Brickey

Limited research has been conducted related to the development of mathematical optimization models for production scheduling at large surface coal mines using the area, i.e., strip, mining method. Increased economic and technical challenges have led to a new interest in production schedule optimization models for these type of mining operations like those currently applied to model underground and open pit mines. While area mines share similar characteristics to both open pit and underground metal operations, neither an open pit nor underground production scheduling model adequately depicts an area mine mathematically. We present an integer programming model with blending constraints and discuss the challenges and opportunities related to the implementation for area mines as well as future research in area mine production scheduling.

Jun 25, 2023

By J. Sattarvand, P. C. Augustine

Despite significant safety improvements, the mining industry remains one of the most hazardous occupations globally and the evacuation of Miners, when an uncontrollable incident occurs in the mine, is the best bet to saving lives. However, Human factors/behaviors during an emergency are likely to influence the evacuation performance. Other industries have made a significant effort to determine these human factors that can impede evacuation performance, however, the current state-of-the-art in mine evacuation or self-rescue is that the evacuation route is predetermined, and a static sign is used to direct miners to the predetermined safe location. This method is limited in representing actual conditions that arise in a real emergency, neglecting the different behaviors displayed by humans. As optimization of the evacuation of a mine plays a fundamental role in emergencies and modeling evacuation behavior and movement of miners is a complex task, this research utilized Agent-Based simulations to simulate the evacuation behavior and performance. It was observed that people with the smart evacuation device made fewer mistakes and arrived at the safe place in less time compared to those have no access to the device. The Mathematical model used in optimizing the shortest path to a safe place is also explained in this paper.

Jun 25, 2023

By K. S. Mortensen

The softwall mining system is a novel, new method of mining mineral deposits in soft, shallow, nonrock ground conditions. This method can mine the ore layer without substantially disturbing the existing overburden. The softwall mining system consists of machinery that is hydraulically controlled and powered, that can be buried (or used on the surface) to extract the ore or mineral from a layered deposit. The method is essentially an application of the longwall mining concept, modified for loose overburden and ore conditions, combined with hydraulic mining.

Jan 1, 2003

By J. Navoyski, B. Macdonald, W. J. Helfrich, J. L. Bellanca, B. Demich

DISCLAIMER The findings and conclusions in this paper are those of the authors and do not necessarily represent the official position of the National Institute for Occupational Safety and Health, Centers for Disease Control and Prevention. Mention of company names or products does not constitute endorsement by NIOSH. ABSTRACT Recent advances in computing, rendering, and display technologies have generated increased accessibility for virtual reality (VR). VR allows the creation of dynamic, high-fidelity environments to simulate dangerous situations, test conditions, and visualize concepts. Consequently, numerous products have been developed, but many of these are limited in scope. Therefore, National Institute for Occupational Safety and Health researchers developed a VR framework, called VR Mine, to rapidly create an underground mine for human data collection, simulation, visualization, and training. This paper describes the features of VR Mine using self-escape and proximity detection as case studies. Features include mine generation, simulated networks, proximity detection systems, and the integration and visualization of real-time ventilation models. INTRODUCTION There are many definitions of virtual reality (VR) that include various levels of immersion and features [1]. Some definitions refer to specific technologies [2], while others are limited to visualization [3]. For this paper, a more general definition of VR will be adopted. VR is defined as the collection of hardware and software that interactively engages users and stimulates their senses within a synthetic or virtual environment. From a hardware standpoint, this can include anything from a phone to a head-mounted display (HMD) to a large-scale theater as well as speakers, microphones, haptic sensors, and interaction devices. The software used to create virtual environments (VEs) generally includes a game engine, custom software components and libraries, and two-dimensional and three-dimensional graphical assets. Recent hardware and software advances have increased the fidelity and availability of VR. New and improved technologies including HMDs and high-resolution monitors and projectors can display sharper, more detailed visualizations. For example, in the past five years between the release of the Oculus Rift DK1 (2013) and the HTC Vive Pro (2018), there was a three-fold increase in resolution along with a 50% increase in the refresh rate. Furthermore, despite early claims that low-cost VR technology was readily available [4], computational power has not been sufficient to handle the large amount of data generated by these systems [5]. In the past five years, however, rendering speeds have more than doubled and memory has more than tripled [6], allowing these visualizations to be incorporated into higher-complexity and -fidelity VEs that more closely mirror the real world. Similarly, software capabilities have also significantly improved through game engine advancements and feature development. In the past several years, game engines have added and improved features such as physics, lighting, platform support (e.g. Android), and asset development integration. Some of the current leading commercial game engines are Amazon Lumberyard, CryEngine, Unreal, and Unity, but this can quickly change as is evident in the literature [7, 8].

Jan 1, 2019

By Brendan Demich, Brendan Macdonald, Timothy J. Orr, Jason Navoyski, Jennica L. Bellanca, William J. Helfrich

Recent advances in computing, rendering and display technologies have generated increased accessibility to virtual reality. Virtual reality allows for the creation of dynamic, high-fidelity environments to simulate dangerous situations and test conditions and to visualize concepts. Consequently, numerous products have been developed, but many of these are limited in scope. Therefore, U.S. National Institute for Occupational Safety and Health (NIOSH) researchers developed a virtual-reality framework, called VR Mine, to rapidly create an underground mine for human data collection, simulation, visualization and training. This paper describes the features of VR Mine, including mine generation, simulated networks, proximity detection systems, and the integration and visualization of real-time ventilation models.

By Brendan Demich, Brendan Macdonald, Timothy J. Orr, Jason Navoyski, Jennica L. Bellanca, William J. Helfrich

Recent advances in computing, rendering, and display technologies have generated increased accessibility for virtual reality (VR). VR allows the creation of dynamic, high-fidelity environments to simulate dangerous situations, test conditions, and visualize concepts. Consequently, numerous products have been developed, but many of these are limited in scope. Therefore, the National Institute for Occupational Safety and Health researchers developed a VR framework, called VR Mine, to rapidly create an underground mine for human data collection, simulation, visualization, and training. This paper describes the features of VR Mine using self-escape and proximity detection as case studies. Features include mine generation, simulated networks, proximity detection systems, and the integration and visualization of real-time ventilation models.

By Steve Wiig

In 1987, the Rock Springs, WY district office of the US Bureau of Land Management (BLM) began to develop an automated system to store, maintain and manipulate more than 14,000 drill hole logs contained in the district's office files for various solid leasable minerals. The development of this system was based predominantly on a trial-and-error basis, with many procedural changes incorporated over time. The current Automated Drill Hole Database and Analysis System will continue to evolve with new software developments and increased personal expertise in this field. The mission of the BLM's Branch of Solid Minerals is mandated by a series of federal laws. The most important are The Mineral Leasing Act, the Federal Land Policy and Management Act, the Federal Coal Lease Amendments Act and the Surface Mining Control and Reclamation Act. Several regulations, promulgated from these laws, dictate that BLM must perform certain tasks and functions as part of its specific duties. The regulations that apply to the BLM Solid Minerals program are codified at 43 Code of Federal Regulations (CFR) 3400 for coal, and at 43 CFR 3500 for non-energy solid leasable minerals, such as sodium, phosphate and potash. Specific functions required of the Branch of Solid Minerals necessitates the use of geologic and drill hole data analyses. These functions can be divided into pre-lease and post-lease. Examples of pre-lease functions that normally require some level of drill hole data analyses include:

Jan 1, 1992