Search Documents

By B. A. Osei

Research to evaluate possible metrics for predicting dredgeability of compact aggregates, by hydraulically actuated clamshell dredges, shows work done by the pistons as a viable metric. Analysis of field data shows that there is a low, positive, correlation between cycle time (CT) and work done. If this correlation exists, then CT has to be considered an independent variable affecting work done during dredgeability assessment. Further research is required to elucidate the relationship between CT and work done during dredging. The objective of this paper is to test the hypothesis that work done during dredging increases with increasing CT. Kinematics and dynamics of the hydraulic clamshell were modeled and implemented in Simulink® in MATLAB. The model was validated using field data. The model was then used to test the research hypothesis. The results show that work done increases with increasing CT. This work confirms that work done during dredging increases with increasing CT. This result indicates that though an operator can increase the CT to deal with difficult digging, inputting unduly high CTs results in higher energy consumption during dredging.

Jan 1, 2011

By G. F. Friel, G. S. Morrow, J. C. Edwards

An experimental program in the U.S. Bureau of Mines' Safety Research Coal Mine evaluated the effects of dead end crosscuts on the transport time of CO along a mine entry. The presence of carbon monoxide is a characteristic of a fire in its incipient stage, and is significant in the determination of a fire location in a mine from the analysis of arrival times of pre-set concentrations at CO monitors. In this investigation two entries, with a total of ten crosscuts, connected by a room were instrumented with CO sensors as part of a real-time monitoring and data acquisition system. Controlled release of 1% CO was monitored as the contaminant traveled the entries for several different configurations of CO sensors and exhaust fan settings. In addition to the normal longitudinal dispersion of CO due to turbulent mixing at the front of the CO wave, the induced rotation of air established within a crosscut by the entry flow diluted the CO concentration through entrainment. It was determined experimentally for the entry and crosscut configuration considered that the transport time for a specified CO concentration was 27% greater than the predicted time based upon entry volume only, but 13% less than the predicted time based upon entry and total crosscut volume. The proper interpretation of the measured transport time of a specified contaminant concentration between sensors is important for mine safety in the isolation of a fire and plans for miner evacuation.

Jan 1, 1993

By Keros Cartwright

Distribution of temperature within the lithosphere can be significantly affected by the movement of ground water. Stallman (1960) presented the basic equation for the simultaneous transfer of heat and fluid in a porous medium and first used earth temperatures to determine aquifer permeability. Subsequently, studies of rock and soil temperatures were used to determine the flow of water through clay layers separating aquifers (Bredehoeft and Papadopulos, 1965; and Sorey, 1971), and to locate shallow aquifers (Cartwright, 1968; Birman, 1969). Cartwright (1968) showed that shallow aquifers maintain a nearly constant temperature throughout the year and that heat is exchanged between the aquifer and land surface. These temperature data also suggest that shallow aquifers hydrologically connected to surface-water systems have significantly greater effect on temperature distribution than aquifers in the deep artesian basins. Water wells developed in the shallow glacial and dolomite aquifers to depths of over 122 meters (400 feet) in northern and central Illinois produce water at temperatures very close to the mean annual air temperature. An analysis of the character of the rocks and soils suggests that the tem¬perature gradient should, and does, vary according to changes in thermal conductivity due to changes in lithology. This is because, under conditions of steady and uniform flow of heat from the earth's interior to the surface, a greater temperature gradient is required in poorly conductive rocks than in highly conductive rocks to transmit the same quantity of heat. Based on estimated values of thermal conduc-

Jan 1, 1972

By A. M. Marabini, G. Belardi, V. Alesse, E. Spaziani

The objective of this investigation was to verify the effectiveness of commercial and synthetic depressing agents in a complex oxidized zinc mineral flotation flowsheet using sodium sulfides and amine. The flotation tests were run on a finely-disseminated calamine ore grading 16.96% Zn and containing smithsonite, hemimorphite, cerussite, calcite, quartz and iron oxide, present essentially in colloidal form. The reagents used in the testing can be grouped into four classes: guar, starch, celluloses and acrylic polymers having various degrees of substitution and molecular weights. The depressants exhibiting the greatest selectivity towards the gangue (considered as a whole) are tripolyphosphate, polycarboxylic acids, methylcarboxylate guars and ethyl hydroxylic starch. In the rougher stage, the Zn recovery ranged from 70% to 80%, and the Zn grade ranged from 27% to 29%. In the Zn-Fe2O3 separation, the compounds ensuring the most efficient separation are the tripolyphosphate and the polycarboxylic acids. In the Zn-SiO2 separation, the compounds that exhibit the best separation efficiency are tripolyphosphate and guar of methylcarboxylic sodium salt. In the case of the Zn-Ca separation, methyl-carboxylic guar exerts the best depressing effect and does not adversely affect the Zn recovery. The separation provided by ethyl hydroxylic guar is also good, although not as good as the preceding reagent. Regarding the Zn-Al separation, the tripolyphosphate, the celluloses and the carboxylate guars are the best depressants. A hypothesis is advanced to interpret the depressing action of the most effective reagents.

Jan 1, 1995

By D. Panias

Alumina hydroxides such as gibbsite (Al(OH)3) and boehmite (AlOOH) are precursors of many types of alumina that find important industrial applications. The thermal decomposition of AlOOH, which is a more energy saving precursor compared to gibbsite, gives rise to the formation of ?-, d-, ?- and a-aluminas that are used for the production of catalysts. The applications of the aluminas are governed by their properties that are a function of the precursor material and its microstructure. The microstructure in turn is a factor of the method and conditions applied, as well as, in the case of soft chemical processes, on the anions present. Towards these ends, this study was focused on the effect of different anions on the physicochemical characteristics of the alumina hydroxides precipitated in the first 5 minutes after the perturbation of the stability of a supersaturated sodium aluminate solution (Bayer liquor).

Jan 1, 2006

By T. R. Kostecki, A. J. S. Spearing, G. S. Esterhuizen, K. V. Jessu

Discontinuities are geologic occurrences in rock and when present within a pillar, reduce the strength of the pillar. Empirical formulas that are commonly used to determine pillar strength do not explicitly take into account the presence of discontinuities and thus can overestimate the pillar strength. The effect of discontinuities on the strength of pillars has been investigated using numerical models, but in these models, the discontinuity strike was parallel with the pillar faces. In this study, fully three-dimensional hard rock pillars were simulated using numerical modeling to understand the effect of the discontinuity dip direction on square and rectangular hard rock pillars. Based on the results, recommendations to assess a pillar’s strength in the presence of a discontinuity are discussed.

Jan 1, 2018

By S. Acar

The results obtained for the selective flocculation or flotation of natural ores do not usually agree with the corresponding properties of the constituent minerals when present alone. This is mainly due to the presence of dissolved mineral species which can interact in many ways with other components in the system and alter their behavior. In this paper, the effect of dissolved species on the flocculation and electrokinetic properties of sulfide minerals is disscussed. Dissolved Fe, Cu and Ni species are found to affect the properties of chalcopyrite, pentlandite, millerite, pyrrhotite and covellite in certain pH range. These effects are interpreted in terms of species adsorption leading to activation or depression of reagents, surface precipitation and complexation of species, etc.

Jan 1, 1985

By John C. Nigro

Bench scale and pilot plant research was conducted using dolomites (CaO,MgO) lime as the basic additive in the preparation of self-fluxed pellets from a typical magnetic taconite concentrate (5.57 S_2). The specific objective of this investigation was to ascertain the viability of the magnesia lime pellets in high temperature oxidizing and reducing atmospheres. Pellet basicity and induration temperature were major parameters affecting fired pellet quality; temperatures ranging from 1,200° to 1,250" C appeared to be the most favorable for production of self-fluxed pellets with basesities (B) above 1.0. Comparison of the mechani¬cal and metallurgical properties of regular (acid) and self-fluxed pellets (B 1.55) produced under similar conditions in a modified grate pelletizing machine showed that the self-fluxed pellets were more resistant to abrasion and to high and low temperature reduction disintegration, an important consideration in commercial application. The Plus 3 mesh Linder index increased from 68 percent (regular pellets) to over 90 percent (self-fluxed pellets). The reducibility and swelling indices of the self-fluxed pellets were found to be comparable to the regular pellets.

Jan 1, 1972

By K. A. Natarajan, M. K. Yelloji Rao

The effect of galvanic interactions among sulfide minerals such as chalcopyrite, galena, and sphalerite in the presence and absence of a grinding ball material on the flotation recovery of chalcopyrite has been studied. X-ray photoelectron spectroscopy (ESCA) studies were carried out to identify the reaction products on the sulfide minerals after different apes of galvanic interactions. Galvanic contact with active minerals such as galena and sphalerite, either alone or together, significantly affected the floatability of chalcopyrite mineral, such an effect being more severely felt in the additional presence of a grinding medium as well as oxygen. Surface analysis studies revealed the presence of oxyhydroxide species of iron on all the sulfide mineral samples which were in prior contact with the grinding medium. The formation of such oxyhydroxide species of iron was found to be dependant on the relative electrochemical activity of the mineral. Probable electrochemical reaction mechanisms are discussed.

Jan 1, 1990

By S. -H. Kim

This work investigated the effect of the concentration of CO2 and lead contamination on the forest ecosystem. Changes of the plant growth, lead concentration in soil, plant, and soil microbial community caused by CO2 concentration (380 ppm and 760 ppm) and lead contamination (500 mg/kg) were measured. Plant growth was inhibited by 50% due to lead contamination. Particularly, shoot growth was inhibited more than the root. However, the root elongation was not affected by the CO2 concentration increase. The diversity of microbial population with AWCD (Average Well Color Development) and PCA (Principle Component Analysis) showed that the lead contamination has an effect com-pared to CO2 concentration. The Shannon index calculated from DGGE profiles was high in soil with Pinus densiflora, while the effect of CO2 concentration was not significant (P<0.5). The similarity of microbial community from each treatment showed that lead has an effect on plant growth and microbial community rather than the CO2 concentration.

Jan 1, 2006

By Guillermo Krstulovich

Pillar strength is a fundamental variable in the design of room and pillar mining. A number of researchers have investigated the strength of mine pillars by loading cubical, cylindrical and rectangular model pillars to failure in a compression testing machine (1). Several of these researchers have observed an increase in the compressive strength of model pillar with an increase in friction at the platen-specimen interface (2, 3, 4, 5). It has been postulated that the friction prevents lateral expansion of the specimen, thereby exerting a confining pressure at the interface. Seldenrath and Gramberg in their work with cylindrical specimens of limestone and marble noted that the effect of clamping the ends of the specimens, i.e., to restrict lateral movement of the specimen face, was to increase the compressive strength about 10% for marble and from 50-75% for the limestone, as compared to the same type of specimens when tested with the end planes free (6). No attempt was made to determine the confining pressure exerted by the clamps. In recent years, Bureau of Mines has conducted an extensive study, similar to Seldenrath and Gramberg&apos;s, with dog bone specimens. The confining pressure exerted by the clamps was determined and an increase in the compressive strength with increasing confining pressure noted (7, 8).

Jan 1, 1970

By Evangelos Petrakis, Kostas Komnitsas

This study investigates the evolution of dimensional properties of grinding products, namely, the mass, the surface area, the length, and the number of particle distributions with the energy input in a ball mill. The size analysis of the mill products enables the calculation of the mass distribution of each material at predetermined size classes and then the determination of the other dimensional properties by taking into consideration the geometry of the particles. Based on the distribution of dimensional properties, an effort was made to determine whether the grinding products are fractal in nature. The effect of material type and grinding conditions on the relationship between the dimensional properties and the specific energy input was also investigated. Special importance was assigned to the study of the specific surface area and the surface area production rate, both during the initial grinding stages and at higher energy levels. The determination of the surface area production rate allows the identification of the grinding limit and the maximum specific surface area which could theoretically be achieved. This approach has as ultimate objective the maximization of energy efficiency and subsequently the minimization of the high grinding cost.

By F. F. Aplan, C. E. Raleigh

Three run-of-mine bituminous coals, ranging in rank from low volatile to high volatile A, were floated at nominal -28 mesh (590 µm), -100 mesh (150 µm), and -400 mesh (37µm) feed particle sizes with selected pyrite depressants and a dispersant. For the three coals tested, pyrite and ash -forming minerals were usually rejected best at -100 mesh feed particle size. Depressant additions tended to improve flotation selectivity between pyrite and coal. When joint dispersant-depressant systems were used at -100 mesh (150 µm) feed particle sizes, the total sulfur content of the clean coal decreased further. For a comparable coal yield, less fuel oil collector was required for the flotation of -100 mesh coal than was required for the flotation of either -28 or -400 mesh feed.

Jan 1, 1992

By J. L. Sloughfy

The size distribution and mechanical strength of the iron ore pellet burden are important parameters in determining the efficiency of the blast furnace. From the very outset, the guiding principle of our pellet quality improvement program was that these parameters are also the key to improving productivity and cost control at the pellet plant. Recognizing the need for improved blast furnace burdens and for higher productivity and lower costs at the pellet plant, Carol Lake operators, in conjunction with the IOC Pellet Quality Committee, established the following goals for the improvement of Carol pellets: [ ]

Jan 1, 1981

By L. Evrard, M. Van Camp, J. Y. Yen, R. G. Reddy, D. Mantha

Viscosities of two industrial lead blast furnace slags have been experimentally determined as functions of composition and temperature. A Brookfield viscometer with alumina rods and crucibles were used. Experiments were carried out between 1200 and 1573 K in an argon atmosphere with up to 5% addition of FeO, MgO, and SiO2 to the slags. Results showed that 1) the viscosities of two slags decreased with increase in temperature; 2) addition of FeO decreased the slag viscosities; and 3) addition of MgO and SiO2 increased the slag viscosities. Use of the above slag compositions with the addition of FeO is recommended for successful lead smelter operation.

Jan 1, 2005

By B. K. Kejriwal, A. K. Ghose

Under specific geological environment, the full extraction of a coal seam is not possible either because of its extraordinary thickness or the presence of surface structures and bodies of water or because of the conditions prevailing in upper seams. Not uncommonly, therefore, for working such seams, pillars of coal are left for the permanent support of the overburden, and voids around the pillars are filled with sand to strengthen the pillars and prevent their deterioration with time. However, the paucity of river sand has focussed attention on the need for alternate strategies including trials with partial filling of the voids. This study has sought to examine in the laboratory the effects of partial and complete filling on the ultimate load bearing capacity and post-failure behaviour of small, tall pillars using artificial material.

Jan 1, 1986

By R. M. Kakwani

The filtration and dewatering results of -32 mesh Pittsburgh seam coal are discussed with reference to the microscopic structure parameters, i.e., particle segregation in the cake and particle and pore size distributions at different layers. At low solid concentration of 0.33 kg coal/kg water, a non-uniform cake structure is observed in which the particle and pore sizes increase from the top to bottom layers in the filter cake. An increase in the solid concentration in slurry produces more uniform cake structure and higher filtration and dewatering rates. Air bubble entrapment in the coal filter cakes is also discussed.

Jan 1, 1984

By S. K. Bhoumik, D. K. Sengupta, B. P. Singh

This paper deals with experimental work to improve the settling and filtration characteristics of an industrial sludge from an iron-ore mine using synthetic polymeric flocculants. The experimental work consisted of the characterization and evaluation of suitable flocculants to enhance settling and filtration rates. The optimum dosage of the flocculants were determined. The experimental results revealed that the settling rate can be increased many times, compared to untreated sludge, by using a suitable combination of flocculants. Compared to cationic and nonionic flocculants, anionic flocculants were found to be more efficient in sludge flocculation. The synergistic effect of two anionic flocculants produced the best settling conditions. Filtration test results also reveal that suitable flocculants can improve the dewatering characteristics of the slurry.

Jan 1, 1997

By C. K. Nworu, L. O. Asuquo, C. O. Nebo

Selective flocculation studies of Agbaja iron ore with starch-type and nonionic polyacrylamide-type flocculants has been conducted to determine the effect of flocculant type. The results indicate that corn starch was slightly better than cassava starch in selectivity performance. Cassava starch was in turn better than Superfloc 16, while the poorest results were obtained with commercial starch. Sodium humate shows better dispersive capability, and thus enhanced flocculation results, than sodium silicate. Pulp pH affects the zeta potential, polymer chain configuration and hence selective flocculation. Overall results indicate that recovery and separation of this very fine grained iron oxide by selective flocculation is feasible.

Jan 1, 1995

By Bradshaw, Y. S. Cho

The size of bubbles plays an important role in flotation. Equations used to calculate the size of bubbles all show the effect of liquid/gas surface tension. However, the surface tension does not change much with frother concentration and experiments conducted using single capillaries (or single-hole spargers) do not reveal any clear effect of the frother concentration on bubble size. The size of bubbles does, however, strongly depend on frother concentration when multi-hole spargers are utilized (or when measured in a flotation cell); at low frother concentrations the bubble size is much larger indicating coalescence as a main mechanism determining the size. Coalescence can be prevented at frother concentrations exceeding the critical coalescence concentration (CCC), which in turn was found to be interrelated with the dynamic foamibility index (DFI).

Jan 1, 2001