Search Documents

By Christopher Snee

??care has to be taken that the design is driven by sound geological reasoning and rigorous engineering logic rather than by the very attractive images that appear on the computer screen.??Hoek 1999 Design of a cavern is inextricably linked to the engineering geology of the site. The importance of sound geological reasoning will be illustrated by transportation projects in New York City where there are proposals for at least 11 caverns. These caverns have been the subject of advanced exploration techniques and geological interpretation but even so the raw data falls short of the sophistication of modern numerical methods. This paper will give geological explanations for the engineering characteristics of the rock in New York City which will provide guidance for practitioners when approaching cavern design in New York and elsewhere.

Jan 1, 2008

By Michael R. Smith

Barrick Goldstrike Mines Inc.’s Betze open pit is located at the north end of the Carlin Trend, in Eureka County, NV. Ten open pit gold mines exist on the trend, which strikes northwesterly, through the north end of Eureka County and into Elko County (Fig. 1). The final pit will be about 2440 m long x 1550 m wide (8000 x 5100 ft), elongate in a west-northwesterly direction and about 425 m (1400 ft) deep. The pit straddles the Barrick-Newmont Gold Co. property boundary. History The first hole at the Goldstrike Mine was drilled in 1962. Between 1963 and 1964, 17 shallow holes were drilled with little encouragement, in view of the price of gold at $1.12/g ($35/oz). From 1962 to 1975, several different companies explored the Goldstrike property. In 1975, Pancana Industries acquired the property. In 1976, Pancana’s exploration efforts found sufficient gold mineralization to initiate heap leach production. In 1977, Pancana formed a joint

Jan 1, 1994

By M. R. Smith

Barrick Goldstrike Inc.'s Betze/Post Open Pit is located at the north end of the Carlin Trend, in Eureka County, Nevada, U.S.A. (see location Map, Figure 1). About ten open pit gold mines exist on the trend, which strikes northwesterly, through the north end of Eureka County and into Elko County. The final Betze/Post Pit configuration is shown in Figure 2, Pit Configuration. The final pit will be about 2450m long by 1550m wide, elongate in a west-northwesterly direction. The pit straddles the Barrick/Newmont property boundary. The highest elevation of the pit perimeter is 1800m at the south wall, with the east end pit bottom elevation at 1200m.

Jan 1, 1993

By John D. Rockaway

This report and accompanying engineering geologic map describe the generalized engineering geology of St. Louis County, Missouri for use in determining the most efficient, economical, and environmentally sound program for land development and urban growth. It includes an evaluation of such factors as the physical and engineering properties of soil and bedrock, surface stability, and subsurface geologic structure. The map and text are designed primarily for property owners, engineers, architects, real estate developers, and city planners involved in land-use planning. The geologic information and engineering interpretation must be considered as a general guide and not as a substitute for a complete on site investigation prior to initiation of any land-use project. The map scale, 1:63,360 (1 inch to a mile) is too small to include the detailed information normally provided on the 7 1/2-minute quadrangle series (1:24,000). The smaller scale is most useful at regional planning levels and was chosen to present information on the more significant engineering factors of the geologic environment for county-wide planning and development. A conventional geologic map deals primarily with the distribution and variation of bedrock formations, and a pedologic map presents information on the soil or natural medium for plant growth. Basic geologic maps and pedological maps are valuable tools that can be of assistance in studying the geologic environment, however, these maps do not provide all the information required for land-use planning. The engineering geologic maps are designed to provide this data. The engineering geologic map is related to both of these basic maps but emphasizes the engineering properties of the rock formations and soils rather than their age or origin. Some of the unit boundaries shown on the county map will closely follow some geologic formation and/or pedologic boundaries; others will transgress these conventional boundaries. Earth materials, bedrock and soil, that have similar engineering characteristics have been mapped as one unit without regard to their geologic or pedologic classifications. This is to assure that geological factors are recognized, adequately interpreted, and presented for use in engineering practice.

Jan 1, 1970

By B. G. Hicks

The Manapouri Power Project is located in New Zealand's South Island Fiordland. The project is being constructed for the New Zealand Ministry of Works. Construction began in 1963 and is scheduled' for completion in 1969. The project will divert water from the natural, glacially carved Lake Manapouri, at Elevation 580, through vertical- penstocks into an underground powerhouse 364 feet long, 127 feet high, and 59 feet wide excavated about 700 feet below ground surface and about 560 feet below the present lake level. The possible ultimate power installation will produce 700 megawatts from turbines located in the underground machine hall. The turbine flow will discharge through the 6-mile, 30-foot diameter tailrace tunnel into a fiord arm of the Tasman Sea. The rocks in the project area are primarily Paleozoic Fiordland Complex gneiss, schist, amphibolite, and marble intruded by granitic rocks and pegmatite. Shear zones have been encountered in the tunnels and machine hall. These produce water and occasionally require steel support. The machine hall arch was stabilized entirely by rock bolt reinforcement. Rock mechanics instrumentation has been used throughout the project both for pre-construction design calculations and to monitor tunnel rock loads and movements of the machine hall roof and walls. About 28 miles of the 100-mile transmission line will be constructed across glacially oversteepened slopes and debris or swamp filled valleys between the power plant and the eastern edge of the mountainous area. Steep glacially carved rock slopes and locally unstable glacial till complicated construction of the transmission line access roads.

Jan 1, 1968

By Douglas D. Campbell, Alan S. Imrie

INTRODUCTION Mica Dam is located on the Columbia River just downstream of the "big bend" of the Columbia, where it leaves the Rocky Mountain Trench and begins to flow southwards, approximately 85 miles north of Revelstoke, B.C. (Fig.l). The dam was built as one of three Columbia River Treaty dams in British Columbia which regulate the flow of the river and provide flood control downstream in Washington and Oregon. In addition, the three Canadian dams make possible greatly increased power generation at existing power plants in the United States and further development along the Columbia and its tributaries in British Columbia. History Mica Dam, constructed during the period 1967 to 1973, is a zoned earthfill embankment 650 feet high, which has 12,000,000 acre feet of live storage and an available head of 550 feet. Power intakes which would serve either a six-unit surface or underground plant were incorporated into the design and construction of the right abutment of the dam (Fig. 2). Prior to 1971 alternative 2500 MW capacity surface and underground powerplant arrangements were studied. Cost estimates for the two alternatives were the same within the limits of estimating procedures. However, it was believed there was a certain continuing risk in locating a surface plant at the toe of a steep canyon wall. Therefore, in 1971 a tentative decision was made to proceed with an underground plant, provided that additional exploration confirmed assumptions of

Jan 1, 1976

By Michal Bukovansky

The Sahara Desert presents a serious obstacle to transportation route development in northwest Africa. Most highways and railroads are now limited to the coastal regions. A network of pioneer roads is the only connection between Algeria, Morocco, and Tunisia on the north, with Mali and Niger on the south. A feasibility study has recently been made for a paved highway between these countries. Climatic, geologic, physiographic and hydrologic conditions will significantly influence the construction of the road. In order to reduce costs, special construction methods will be required. An outline of these I conditions and methods is presented as an example of an engineering geological investigation in desert conditions.

Jan 1, 1970

By Reese E. Mallette

This paper makes five major points which may be contributions to the art of limestone sinkhole engineering. First, solution cavity development in limestones is dependent in great measure on pyrite contained within the limestone. Second, rock failure is rarely involved in sinkhole problems, while soil failures are almost always the mode of occurrence. Third, draw down, depression of the water table, is a primary causative factor in sinkhole development. Fourth, lateral movement of vadose water along the soil-rock interface, sub-soil erosion, is the mechanism by which soil is stoped, raveled, piped, or removed from the soil cavern. Fifth, the ultimate or triggering factor in localizing a sinkhole collapse is any superposed mechanism which disrupts the continuity of an impermeable clay soil overburden. The above theses are presented as extensions of our observation and of published literature, with the suggestion that additional study of these mechanisms is warranted.

Jan 1, 1975

By W. H. Davitt

One might ask why someone like myself, involved in the determination of taxes, should be speaking at a "cost engineering" session of a national engineering society. While it is true that taxes, especially income taxes, whether they be federal, state, or local, are not usually thought of as a "cost" of doing business, it is equally true that these tax costs do reduce the distributable profits just as much, as the cost of power, supplies, or labor. Therefore, the consideration given to taxes is often as important as that given to other costs. Hopefully yea will recognize that, within certain limits, taxes can be controlled to an economic advantage. That question may then lead to another question: What does the amount of taxes have to do with me? I'm an engineer or manager; not an accountant or a lawyer. If I may take a few minutes of your time, I might be able to present in a brief discussion some interesting facts that will provide the answers to those questions. My discussion will be directed mainly to Federal taxes. However, much of it will be applicable to state and local taxes, also.

Jan 1, 1973

By John A. Bischoff, Francis S. Kendorski

A technique that has been used for inspection and appraisal of rock tunnels is described. It enables a rapid and complete record to be made of those factors necessary for the engineering assessment of the rock conditions surrounding a tunnel. Full understanding of the regional geology, and a careful recording of data concerning the principal geological and construction factors is essential basic data for a tunneling project, whether the tunnel is under construction or is already in service. A methodical recording of data concerning general geology, shears, fracture orientations, spacing, persistence, rock classification, water condition, shear frequency, excavation method, blasting procedure, and rock stabilization and support methods, combined with a photographic record, can be completed by experienced engineers and geologists at the rate of over 1000 feet of tunnel per shift.

Jan 1, 1976

By Robert M. Adler

In order for a taxpayer to produce income, he may be required to exhaust his capital assets. With respect to the mining industry, those exhaustible capital assets may result in income tax deductions under the general categories of depreciation, obsolescence, losses and depletion. The percentage depletion deduct ion concept is not based upon "economic" depletion, or "geological" depletion theories. Instead, it is wholly an income tax concept created by Congress. This is significant in that, in its application, tax depletion has no adherence to traditional economic or geological depletion concepts For example, the Internal Revenue Code limits percentage depletion to 50 percent of the miner's net income for the taxable period.1/ Should a particular miner extract and sell 500,000 tons of material during the year, but at a loss, he receives no percentage depletion. The same would apply to an electric utility which mined its own coal. Should its mining costs exceed the "going price" for coal, as established by actual arm's-length sales in the market, the utility has no net income, and is therefore not entitled to percentage depletion.2/

Jan 1, 1973

By V. Nasri, S. Rashidi

The Baltimore Red Line Project is a proposed 22.7-km (14.1-mile) long east-west light rail transit (LRT) line envisioned to connect the areas of Woodlawn, Edmondson Village, West Baltimore, downtown Baltimore, Inner Harbor East, Fells Point, Canton and the Johns Hopkins Bayview Medical Center Campus. The Red Line LRT System has two tunnel segments - the Cooks Lane Tunnel (CLT) and the Downtown Tunnel (DTT). The CLT segment is roughly 1,920-m (6,300-ft) long. It commences at the west portal located at the highway ramp for I 70 (to be removed) and terminates at the east portal that is at the intersection of Edmondson Avenue (U.S. Route 40) and Glen Allen Drive. This segment of the project consists of the following construction components: approximately 1,458 m (4,786 ft) of tunnels, 143 m (469 ft) of cut-and-cover tunnel, and 318 m (1,045 ft) of retained cut (U) section. The approximate horizontal alignment for the Red Line LRT Project is shown in Fig. 1.

Jan 1, 2014

By J. van der Walt

In hot deep mines the ventilation and refrigeration requirements are determined primarily by the magnitude of the various sources of heat, and where in the mine they arise. Refrigeration is expensive, and in order to ensure that it is utilized effectively and at the lowest possible operating costs it is important that careful attention be given to the selection of plant, and how the cooling is to be distributed. The paper outlines the essential features of the highly effective strategy that has evolved in recent years in cooling deep mines in South Africa.

Jan 1, 1980

By D. Yokom, T. Katsabanis, E. Tremblay

"The mining industry has always faced the problems of replacing retired mining professionals, retaining their knowledge, continuously developing the skills of local talent and employing under-represented groups. In expansionary scenarios the industry faces the additional challenge of increasing available talent. New talent has traditionally come from current mining programs; however, these programs have been declining in numbers, and those that remain face challenges such as fluctuating enrollments, and reduced budgets. Queen’s University and Northern College have partnered to develop an innovative new program that offers online mining education to engineering technologists seeking to upgrade their skills and obtain a Bachelor’s degree. The high quality, flexible curriculum, offered online, includes a wide range of learning activities that promote interaction (student-to-student, student-to-instructor, and student-to-content), and is enabled by modern learning technologies (an integrated learning platform, as well as a variety of types of purpose-built video, web conferencing, and simulation software). The program issues block transfer credit to college graduates, and consequently reduces the time to completion when compared to other Bachelor’s degrees in Mining. The curriculum has been carefully designed to enhance a balance of technical, managerial, and societal skills for students. The program also includes short summer field school sessions, where students gain practical application skills under the direct supervision of engineering experts. THE NEEDS OF INDUSTRY Canada is the world’s largest exporter of minerals, and the contribution of this sector to Canada’s gross national product is more than three times that of the automotive industry, representing approximately 4% of Canadian GDP (MiHR, 2015)1. According to a recent report by the Canadian Mining Industry Resources Council (MiHR, 2016)2, despite the recent downturn in commodity prices, the industry will continuously need to attract new engineers to replace talent retirements and prepare for the possibility of expansion when the industry recovers. As past experience indicates, the challenges during expansion times are severe and the effects on education counter-productive. For example, during the prolonged expansion cycle of 2006-2012, several new programs were started worldwide, and mining became the profession of choice for many young students. During the subsequent downturn in the industry, many of these programs face dwindling enrollments, placing their sustainability in question. However, there is a continual need by industry to retain employees, as well as attract and train local talent, while providing educational opportunities to its employees. High potential college graduates can find themselves reaching a ceiling in their advancement due to their lack of a University degree. Furthermore, there exists an under representation of women, immigrants, and Aboriginal peoples in the labour force, and engineering fields in general1,2. Traditional mining engineering programs have tried to respond to the needs of industry, as well as meet the needs of students seeking diverse and successful employment careers. These programs tend to cater to the educational needs and aspirations of a general population, and their ability to grow and respond to changing industry needs is constrained by the number of students they can attract, as well as the resources available to them in a steady-state scenario."

Jan 1, 2017

By W. M. Middleton

The exploiting of geothermal steam is a new endeavor in this country and is for that matter a very new science in the world. With the majority of steam wells in the world having been drilled during the last twelve years relatively little experience and knowledge has been gained that can guide us as compared to the techniques the oil and gas producers have developed for their use. We few technical personnel associated with the field find it a continuous challenge to understand and explain what effects or causes the various unusual phenomenon experienced. We have had unending discussions attempting to formulate pet theories which we can use as guides. We know, so the geologists tell us, that the source of the heat is from the hot magmatic core of the earth. Theory has it that the magma is cooling off and that hot gases are given off as this magma cools and shrinks. In volcanic' areas along fault lines where the magma reaches closer to the surface than in other areas, there is a higher concentration of gas evolution; consequently, geyser or geothermal areas are developed. As these hot gases rise toward the surface they encounter various minerals, including overlying bodies of water. It is into these underground lakes that our wells are penetrating. As the heat enters these lakes it spreads out by conduction, convection and water migration. We can strike this hot water over quite large areas in many of the geothermal fields. At present there is one anomaly to this in the United States as there is in Italy where our wells do not penetrate a hot water lake. This is at The Big Geysers in California. Here superheated steam is produced with a heat content, so high that it could not have been boiled off of a fresh water pool. This puzzled us until last year when a well was completed into a large body of brine in the Imperial Valley. This brine exists at close to 500°F and at a hydrostatic pressure sufficient to preclude any boiling. It is now believed by some of us that a similar pool of brine must exist below The Big Geysers area, from which the steam is emanating. If there is such a brine pool, it offers a plausible explanation of the high-heat content, for brine boils at a higher temperature than fresh water. I am now beginning to think that a similar brine pool may exist under all the geothermal basins for if it is under two of them, it is highly probable that it is under the others. The partial understanding of what we are drilling toward, and formulating a theory to explain its behavior helps guide us in our steam well drilling.

Jan 1, 1963

By D. T. Kinard, A. A. Schweizer

An operational 9 meter (30-foot) high gold heap leach pile was investigated by excavating test pits up to 6 meters (20 feet) deep, obtaining bulk and relatively undisturbed thin wall drive samples, and observing the ore distribution patterns exposed in the test pit walls. The clayey ore is crushed, agglomerated with lime and cement, and deposited on the leach pads using a radial stacker. Laboratory tests performed included moisture-density, gradation, compaction, Atterberg limits, permeability (constant and falling head), and triaxial strength tests. Discussion is presented on the effects of agglomeration on the permeability and strength characteristics of the in-place ore. Also discussed is the effect of deposition of the ore using the radial stacker.

Jan 1, 1987

By D. T. Kinard, A. A. Schweizer

An operational 9 meter (30-foot) high gold heap leach pile was investigated by excavating test pits up to 6 meters (20 feet) deep, obtaining bulk and relatively undisturbed thin wall drive samples, and observing the ore distribution patterns exposed in the test pit walls. The clayey ore is crushed, agglomerated with lime and cement, and deposited on the leach pads using a radial stacker. Laboratory tests performed included moisture-density, gradation, compaction, Atterberg limits, permeability (constant and falling head), and triaxial strength tests. Discussion is presented on the effects of agglomeration on the permeability and strength characteristics of the in-place ore. Also discussed is the effect of deposition of the ore using the radial stacker.

Jan 1, 1987

By Richard E. Thill

Engineering properties of rock are essential in most phases of mining from site reconnaissance through mineral processing. Review of the literature indicates, however, that property data is scarce for most coal measure rocks in the United States. The Bureau of Mines, U.S. Department of the Interior, has undertaken a wide-ranging testing program to provide more complete property data for coal strata in the U.S. coal basins. The property data are expected to have application in geophysical exploration, the development of pre- mining and hazard detection probes and instrumentation, mine design, engineering and rock mass classification, subsidence engineering, and ground control. This paper describes the comprehensive program encompassing in situ geological, geophysical, and geotechnical properties and laboratory determinations of acoustic, electromagnetic, physical, mechanical, and index properties and discusses results for 500 ft of coal measures at a minesite in the Northern Appalachian, Eastern Coal Province.

Jan 1, 1982

By S. S. M. Chan

The design of most underground support systems has largely been based upon empirical rules. This design method has proven to be satisfactory in most cases as witnessed by the number of successfully completed works. However, the adequacy of this approach to the developing technology of ground support systems associated with deep excavation has not been substantiated. In cases where the material has definite time-dependent behavior parameters, rules of past experience become extremely vague and conservative. The Spokane Mining Research Center is currently engaged in extensive research to develop rational design methods for underground structures which will account for the many interacting factors such as in-situ properties of the rock mass, excavation methods, proposed types of support system, construction sequence, and environmental variables. The information presented in this paper pertains to only a segment of the research program,

Jan 1, 1971

By Maynard O. Serbousek, Melvin E. Poad

Shotcrete, a useful support material in underground openings, is a sprayed concrete, and, when used with fast-setting agents, is immediately self-supporting. Although shotcrete has been used extensively for tunnel support, the technique has not been readily accepted by the mining industry because of the lack of essential information on such basic items as material properties and rock interaction. The Spokane Mining Research Center (SMRC) of the Bureau of Mines has been active in the field for the past 2 years, including research on fibrous reinforced shotcrete. IIT Research Institute, Chicago, under Bureau of Mines contract, is investigating physical properties of shotcrete as affected by (1) type of process (wet or dry) and (2) fast-set agents and controlle-dset cements. Already the contractor has shown the advantage of a regulated-set cement over normal cement and fast-set additives for the dry process. The regulated-set cements can produce high early strengths with no decrease in ultimate strength.

Jan 1, 1997