Search Documents

By Yi Luo

Bolting the mine roof is one of the noisiest underground mining operations. The main contribution to the noise is the drilling of the roof bolt holes, especially drilling in hard rock. Previous research shows that the specific energy consumed in drilling bolt holes is inversely proportional to the bite depth (i.e., penetration per drill revolution). Less specific energy at a reasonably high bite depth means less energy is wasted in the drilling process for producing heat, bit wear and noise. Therefore, proper control of the drilling operation to achieve a reasonably higher bite depth can reduce drilling noise from its sources as a proactive noise control approach. In order to explore the feasibility and develop the proactive technology for reducing drilling noise, drilling tests have been conducted in laboratory settings. The preliminary results show that significant reduction in noise dose can be achieved by drilling in medium hard rock with uniaxial compressive strength of about 276 bars (4,000 psi) and at a reasonably high bite depth of about 4.6 mm/rev (0.18 in./rev). This paper presents the findings from laboratory experimental studies.

By A. J. S. Spearing, G. Bylapudi, K. Mondal

The mining industry is a major consumer of rock anchors in the United States. Due to the high humidity in the underground coal-mining environment, the rock anchors corrode and lose their load bearing capacity, which, in turn, reduces the life expectancy of the ground support. This creates operational difficulties and a number of safety concerns (Li and Linblad, 1999). Research on rock anchor corrosion has not been adequate in the past and the effects of several factors in the mine atmosphere and waters are not clearly understood. One of the probable reasons for this lack of research may be attributed to the time required for gathering meaningful data. Underground water samples from different mines in the Illinois coal basin were collected and the major chemical content was analyzed and used for laboratory testing. The corrosion performance of the different commercial rock anchors was investigated by techniques such as laboratory immersion tests in five different corrosion chambers and potentiodynamic polarization tests in simulated ground waters based on the Illinois coal basin. The tensile strengths were measured for the selected rock anchors taken every three months from the salt spray corrosion chambers maintained at different pH values and temperatures. The corrosion potential, corrosion current and the corresponding corrosion rates of the #5, #6, #6 epoxy-coated and #7 forged-head rebar steels, #6 and #7 threaded-head rebar steels were measured in the pHs of 5 and 8 at room temperature. The open circuit potential (OCP) readings of the different rock anchors were recorded in three selected underground coal mines (A, B & C) in the Illinois coal basin and the data compared with the laboratory electrochemical tests for analyzing the life of the rock anchors installed in the mines with respect to corrosion current measured.

Jan 1, 2010

By R. Bhaskar

The results of an experimental study on the dispersion and deposition characteristics of fine coal dust in mine airways are presented. Experiments were conducted at various flow velocities using bituminous and semi-anthracite-coal dust which had a large proportion of dust in the respirable size range. Cross sectional variations in the concentration of dust at various points in the airway were also measured. Instruments used in the experiments included gravimetric samplers and impactors. Concentration measurements were made both for the respirable and total airborne dust. The experimental design, sampling procedures and results are discussed. The study is aimed at providing a better understanding of the temporal and spatial behavior of dust particles in underground mine airways.

Jan 1, 1986

By R. V. Ramani, R. A. Jankowski, R. Bhaskar

The spatial distribution of airborne dusts, deposition of dust in the airway, as well as the effect of airflow velocity and particle density on dust behavior in mine airways were studied in a set of experiments performed in a mine airway under controlled conditions. Considerable deposition of dust near the source was indicated. Pronounced effects due to velocity were observed in ambient dust concentration and deposition along the mine airway, both in the respirable and the total size ranges. Cross-sectional concentration measurements indicate an increase in concentration from the roof to the floor. The average cross-sectional concentration is about 75% of the concentration in the center of the airway.

Jan 1, 1987

By Stefan Gerl, Werner Stahl

Steam pressure filtration combines mechanical and thermal processes in one filtration device. Steam condensation at the cold layers of the filter cake, build a condensation front, which even removes the capillary water from the porous filter cake. Depending on the choice of parameters it is possible to achieve a very low residual moisture content. The influence of the parameters on the dewatering results was systematically examined on a bench-scale apparatus. This paper explains the physical fundamentals, the influence of the cake dewatering parameters, and one possible method of applying the process to a disk filter device as well.

Jan 1, 1995

By Rong Lu, Hao Wu, Bing Dai, Guoyan Zhao, Li Cheng, Weizhang Liang

Affected by the disturbance of blasting activities, deformation instability and rock dynamic disasters are prone to occur in deep hard rock roadways. Thus, it is particularly necessary to understand the failure behavior of rocks and roadways under dynamic loads. In this study, a series of impact loading tests were carried out on sandstone samples with and without a circular cavity by a modified split Hopkinson pressure bar (SHPB) test system. The mechanical properties and energy evolution of the samples were systematically investigated, and the effect of cavity size was analyzed. The results showed that the presence of the cavity in the samples weakens the dynamic compressive strength by more than 10%, and the peak strain and brittleness are also reduced to varying degrees. Under dynamic loading, spalling cracks occur first on the roof and floor of the cavity, and then different numbers of shear cracks are formed on the sample diagonals. The eventual shear failure mode is the result of the connection of the shear cracks and the cavity. As the cavity radius increases, the dissipated energy density and fractal dimension both grow accordingly, leading to smaller and smaller rock fragments. The dynamic failure behavior of the circular cavity can be well explained based on the dynamic stress distribution law. Overall, this study can provide a reference for the study of the mechanism of rock burst in deep roadways.

Feb 18, 2021

By RICHARD A. THOMAS, Liming Yuan, Lihong Zhou, DAVOOD BAHRAMI

Mine ventilation simulation software has become an essential tool for the mining industry to design and manage mine ventilation operations. Building a well-calibrated mine ventilation network is time consuming, however, and requires great effort. In the last several decades, the mining industry has seen a steady increase in the use of air velocity sensors to monitor airflow and detect unexpected abnormal airflow in some key locations in underground mines. The present research work was carried out to explore the possibility and methodology of calibrating a ventilation network model using atmospheric monitoring system (AMS) data on a routine and ongoing basis.

Aug 1, 2022

By L. Zhou, L. Yuan, R. A. Thomas, D. Bahrami

The abstract emphasizes the importance of a calibrated ventilation network model for mine ventilation planning, optimization, and fire simulation. It highlights the impact of continuous airflow monitoring on improving model calibration. The paper discusses an experimental study at the Safety Research Coal Mine (SRCM) to understand the use of continuous airflow data for model improvement. It also addresses practical problems in calibration and tuning using this data, including analysis of air velocity sensor fluctuations and application of sensor location correction factors for accurate average air velocity.

Mar 7, 2022

By K. Shoji

Residence time distributions (RTDs) were estimated by water tracing in a number of wet overflow ball mills (diameters 0.38 to 4.65 m) producing dense, coal-water slurries. In open-circuit mills of 0.38 m diameter and various length-diameter (L/D) ratios, the mean residence times of solid were also determined from measured mill holdups. Holdup increased with increased mill feed rate, but the mean residence times of coal and water were still equal to each other. The experimental residence time distributions were fitted to the Mori-Jimbo-Yamazaki semi-infinite, axial mixing model, and the dimensionless mixing coefficient was determined for each of 25 tests in single- and two-compartment mills. This coefficient was found to be independent of the feed rate but linearly proportional to the D/L ratio. The mixing coefficient was smaller for two-compartment mills than for single-compartment mills, showing that there was reduced mixing introduced by the diaphragm separating the compartments. Equations are given to scale residence time distributions for changes in mill diameter and length.

Jan 1, 2008

By Fabian Laumen, Sunny Schoone, Felix Leaman, ELISABETH CLAUSEN

The paper evaluates the attenuation behavior of acoustic emission (AE) signals in four different materials used in marine environments. The study aims to identify materials with the highest and lowest AE signal attenuation, providing insights into wave propagation and structural monitoring in deep-sea mining applications.

Dec 1, 2023

By M. R. Shahan, W. R. Reed, S. Klima, T. W. Beck, Y. Zheng

Testing was conducted to determine the ability of foam to maintain roof coverage in a simulated longwall mining environment. Approximately 27 percent of respirable coal mine dust can be attributed to longwall shield movement, and developing controls for this dust source has been difficult. The application of foam is a possible dust control method for this source. Laboratory testing of two foam agents was conducted to determine the ability of the foam to adhere to a simulated longwall face roof surface. Two different foam generation methods were used: compressed air and blower air. Using a new imaging technology, image processing and analysis utilizing ImageJ software produced quantifiable results of foam roof coverage. For compressed air foam in 3.3 m/s (650 fpm) ventilation, 98 percent of agent A was intact while 95 percent of agent B was intact on the roof at three minutes after application. At 30 minutes after application, 94 percent of agent A was intact while only 20 percent of agent B remained. For blower air in 3.3 m/s (650 fpm) ventilation, the results were dependent upon nozzle type. Three different nozzles were tested. At 30 min after application, 74 to 92 percent of foam agent A remained, while 3 to 50 percent of foam agent B remained. Compressed air foam seems to remain intact for longer durations and is easier to apply than blower air foam. However, more water drained from the foam when using compressed air foam, which demonstrates that blower air foam retains more water at the roof surface. Agent A seemed to be the better performer as far as roof application is concerned. This testing demonstrates that roof application of foam is feasible and is able to withstand a typical face ventilation velocity, establishing this technique’s potential for longwall shield dust control.

Jan 1, 2017

By M. R. Shahan, W. R. Reed, S. Klima, T. W. Beck, Y. Zheng

Testing was conducted to determine the ability of foam to maintain roof coverage in a simulated longwall mining environment. Approximately 27 percent of respirable coal mine dust can be attributed to longwall shield movement, and developing controls for this dust source has been difficult. The application of foam is a possible dust control method for this source. Laboratory testing of two foam agents was conducted to determine the ability of the foam to adhere to a simulated longwall face roof surface. Two different foam generation methods were used: compressed air and blower air. Using a new imaging technology, image processing and analysis utilizing ImageJ software produced quantifiable results of foam roof coverage. For compressed air foam in 3.3 m/s (650 fpm) ventilation, 98 percent of agent A was intact while 95 percent of agent B was intact on the roof at three minutes after application. At 30 minutes after application, 94 percent of agent A was intact while only 20 percent of agent B remained. For blower air in 3.3 m/s (650 fpm) ventilation, the results were dependent upon nozzle type. Three different nozzles were tested. At 30 min after application, 74 to 92 percent of foam agent A remained, while 3 to 50 percent of foam agent B remained. Compressed air foam seems to remain intact for longer durations and is easier to apply than blower air foam. However, more water drained from the foam when using compressed air foam, which demonstrates that blower air foam retains more water at the roof surface. Agent A seemed to be the better performer as far as roof application is concerned. This testing demonstrates that roof application of foam is feasible and is able to withstand a typical face ventilation velocity, establishing this technique’s potential for longwall shield dust control.

Jan 1, 2018

By Panshi Xie, Yan Chen, Shaogang Wu, Yang Hang

In order to realize the intelligent mining of coal seam with large dip Angle, this paper adopts the methods of large proportion variable Angle loading threedimensional physical simulation experiment, numerical simulation and field measurement with digital twin technology. The hydraulic support with large dip Angle and large mining height is used as the prototype to design the physical entity model of 1:5 hydraulic support, combined with modeling and graphics rendering technology. Angle, displacement and load sensors were selected and placed to realize the data channel between the lower machine and the upper computer of the digital twin system, so that the position and load data of the physical entity model and the twin model of the laboratory hydraulic support could be shared in real time. Moreover, the multi-dimensional dynamic and static load transfer law and the position evolution characteristics of the support and surrounding rock under different inclination angles were analyzed. The results show that: with the increase of the Angle of the working face, first, the initial support force required by the support decreases, and the damage degree of the roof increases; When the roof is soft, the lifting operation can avoid the instability of the support to a certain extent. Second, under the action of positive pressure, the load of the top beam under different angles is balanced; Under the backpushing action, the load in the upper inclined area of the shield beam increases gradually, while the load in the lower inclined area decreases gradually. Under the lateral push, the load changes periodically, and the load in each cycle is increased compared with that in the previous cycle. Third, the numerical simulation analysis shows that the load on the lower bracket is less than that on the upper bracket, and the load on the bottom of all the columns is greater than that on the middle and upper brackets. In order to reduce the impact of the columns on the bottom plate or the base, it is necessary to improve the anti-subsidence ability of the base. Finally, according to the research results, the improvement and optimization measures of the support are put forward, and the field test shows that these measures effectively solve the problems of sinking, sliding and tipping of the support in the working face with large inclination Angle, and obtain good application results.

Feb 1, 2024

By Richard A. Thomas, Liming Yuan, Wei Tang, JOHN SOLES

Lithium-ion (Li-ion) battery applications are increasing for battery-powered vehicles because of their high energy density and expected long cycle life. With the development of battery-powered vehicles, fire and explosion hazards associated with lithium-ion batteries are a safety issue that needs to be addressed. Li-ion batteries can go through a thermal runaway under different abuse conditions, including thermal, mechanical and electrical abuse, leading to a fire or explosion. The National Institute for Occupational Safety and Health (NIOSH) mining program is conducting research to prevent and respond to lithium-ion battery fires in battery-electric vehicles in the mining industry. In this study, experiments were conducted to investigate the effectiveness of different suppression systems including dry chemical, Class D extinguishing powder and water mist for lithium-iron-phosphate (LFP) battery pack fires. The effects of activation time and release time of the water-mist system on the suppression of the LFP battery (a type of Li-ion battery) fires were studied. The results of this study may be helpful for developing strategic firefighting and response plans for battery-powered vehicles used in mining.

Aug 1, 2024

By Sandro Moro, Giuseppe Tiberti, Giovanni Plizzari, Antonio Conforti

"During TBM operations, thrust jacks apply high-concentrated forces to the last installed precast segment. These loads generate a disturbed region in the precast segment under the thrust jacks, in which significant tensile stresses (defined as splitting or bursting stresses) occur perpendicular to the load direction. In addition, due to the demand of compatibility, the combined effect of TBM high-concentrated loads determines tensile spalling stresses in the area far from the loads. Therefore, local rebars or fiber reinforcement are required in these areas. This paper focuses on the study of the effects generated by high-concentrated loads exerted by TBM hydraulic jacks, mainly in terms of both spalling and splitting phenomena. Experimental tests on small-scale specimens showed that polypropylene fiber reinforcement significantly enhances both the bearing capacity and the ductility. Moreover, polypropylene fibers resulted in very effective control of compatibility cracks.INTRODUCTIONTunnel segments are generally reinforced by conventional rebars (RC segments) in order to resist the tensile stresses both at Serviceability (SLS) and Ultimate Limit States (ULS).In the two last decades, Fiber Reinforced Concrete (FRC) has been used in many precast tunnel segments (sometimes also in combination with conventional rebars). Steel Fiber Reinforced Concrete (SFRC) is generally used for these applications even though there is a growing industry interest on macro-synthetic fibers for structural applications. Conforti et al. (2015) showed that polypropylene (PP) macro fibers can be used as shear reinforcement in both wide shallow and deep beams. Referring to precast tunnel linings, very few early experiences are reported in literature. Bonalumi et al. (2015) developed full-scale tests on tunnel elements reinforced by PP fiber reinforcement and conventional rebars (hybrid solution). The design process of segmental concrete tunnel linings generally models the standard load cases of demolding, storage, transportation, positioning and embedded ground condition. In all these stages the ring can be modelled as simple curved beam elements (having a height equal to the lining thickness and a width equal to the segment length). During these loading conditions, flexural demand is generally limited; thus, in case of conventional RC elements, a rather low ratio of longitudinal curved rebars is usually adopted (?s of about 0.2-0.3%)."

Jan 1, 2016

The deformation, failure, and filling characteristics of a caving roof in the initial and normal mining stages of a pitching oblique longwall mining area are analyzed using large-scale threedimensional physical-similitude experiments and numerical calculations to study the characteristics of roof fracture and migration in a steeply dipping seam. The results show that the roof fracture development has evident sequential and spatial characteristics. Among them, immediate roof breaking in different parts of the mining area shows difference in time and space. The failure sequence of the immediate roof in different areas changes with the mining; unique regional stability evolution characteristics are observed in the suspended immediate roof simultaneously, resulting in its significant regional stability on the goaf filling.

Jan 7, 2020

By David A. Summers

In May 1975 the U. S. Bureau of Mines contracted with the University of Missouri-Rolla, Rock Mechanics and Explosives Research Center to develop a Hydrominer modification to a long-wall shearer unit, wherein the rotating pick-laced drums and connecting gear drives are replaced by a water jet cutting head.1 The concept of the water jet cutting head is based on using the high localized energy of the water jets to isolate a slice of coal by cutting a slot under, at the back of, and at the top of the web. The plow blade of the head then advances into the cut and wedges the pillar over onto the conveyor (Figure 1). There were several potential advantages foreseen for the system of which perhaps the most significant were the elimination of coal dust from the working area2 and the ability, with a variation in nozzle geometry, to cut webs of greater depth with a small increase in equipment horsepower. The University initially designed the head, based on experiments carried out in the laboratory, under an earlier Bureau of mines contract. The experiments showed that it was more advantageous to work at a pressure of 10,000 psi with an estimated flow rate of 50 gpm than go to the higher pressures and lower flow rates which have been advocated elsewhere.

Jan 1, 1977

By B. E. Davis, D. A. Stanley, C. E. Jordan

A prototype expert advisor was developed by the U.S. Bureau of Mines to systematically offer advice on the control of a Florida phosphate operation. The PC based system receives input from remote sensors for circuit parameters such as feed rate, reagent addition, and pH and from operator entered information such as the quality of the concentrate and tailings in each of the coarse, fine, and amine flotation circuits. The computer evaluates the information using rules obtained from industry representatives and Bureau flotation experts. Recommended actions and questions are displayed to quickly guide the operator to a problem within the flotation circuit and suggest a solution. This process control system could provide more uniformity among the flotation operators and also serve as a trainer for new operators. In addition, it represents a step toward fully automated systems for phosphate flotation.

Jan 1, 1990

By M. Valdebenito, J. Rajala

An OCS Expert control system was implemented by Svedala Cisa at the Minera Maricunga Refugio Crush-Leach Operation near Copiapo, Chile. The purpose of the Expert system was to maximize production through the primary and secondary crushing circuits and help balance crusher usage between each stage to maximize total plant production. Interesting aspects of the control strategies are discussed. Benefits of the control were verified through a randomized On/Off test program. Tonnage increases ranged from 5% to approximately 20% at good confidence intervals. Benefits analysis results are discussed. The crushing plant at Refugio is very remote and is located at approximately 15,500 ft. This poses many challenges. The effect of altitude and remote location on plant operation are discussed.

Jan 1, 2002

By J. E. Golsan

Barrick Gold Corporation installed an expert style control system on the grinding circuit at its Mercur mine. Barrick's main objective was to increase mill throughput by a minimum of 3%. The expert system team collected operating data and then created a knowledge base using Comdale/X expert system development software. The expert system moved from on-line "advisory" mode, testing of expert rules, to full process control in four weeks. Expert system control benefits include a 9-15% increase in mill throughput, consistent mill loading leading to less wear on SAG mill parts, and improved downstream process control.

Jan 1, 1998