Search Documents

By L. G. Tejada, T. Sjursen

In the production of ferronickel at Falconbridge Dominicana's plant in the Dominican Republic the Reduction Plant plays a vital role by partially reducing the nickeliferous oxide ore, and pre- heating the charge to the electric furnaces. Ore is agglomerated in the form of pillow-shaped briquettes which are screened and fed to 12 open-top shaft furnaces. Hot (over 1250°C) reducing gases are partially cooled (less than 1150°C) and introduced through a set of primary tuyeres. The reducing gas rises counter-currently to the flow of solids. A portion of the partially spent reducing gas is withdrawn at the furnace top and recirculated through a set of secondary tuyeres, 1800 nrm above the primary tuyeres. Together with the recycle gas a controlled amount of air is also added to react with the partially spent reducing gas in order to preheat and dry the charge in the upper part of the shaft furnaces. The calcine is discharged through three discharge legs and pusher block assemblies into open-top refractory lined cars. These cars are then hauled to the electric furnace, parked over selected feed ports, and discharged through bottom gates. The furnace exhaust gas is de-dusted in cyclones and then passed through Venturi scrubbers. The slurry is fed to a thickener, filtered, and recycled to the ore receiving hopper in the ore preparation area. Dust generated throughout the plant is collected, wetted to conform with briquette press feed, and recirculated in a controlled manner through the feed system.

Jan 1, 1979

By Christopher J. Hall

This paper describes the results from computer runs simulating 24 different mine ventilation configurations with the main fan situated first at the top of the upcast shaft and then at the top of the downcast shaft. Real air was used, with evaporation, condensation and heat exchange. The results showed that power requirements for the forcing fan were up to 20% less than for the exhausting fan for equal mass flow rates.

Jan 1, 1989

By A. Haghighat

The Missouri University of Science and Technology?s (Missouri S&T) Experimental Mine is a teaching and research facility which has been excavated in limestone by mining engineering students over almost 100 years. The mine is currently being extended to a second level. Available fans for ventilation are two surface fans of 24 kW and two underground booster fans of 12 kW. The design of a ventilation network in conjunction with multi surface fans and booster fans entails a complex procedure. Ventsim Visual software modeling has been used for network analysis to determine the optimum surface and booster fans locations, blade settings, and speeds. Both natural and mechanical induced ventilation pressures have been taken into account. Three working faces on each level have been designated as target points that minimum air quantities are required. The model has been calibrated against a pressure and quantity survey. Design of ductwork, door/stopping positions and different fans characteristics have been examined. The optimum flow rate at identified working faces, efficiency and minimum energy losses and annual network power cost determine the best scenario. The optimum design has been determined for the ventilation network for the next 100 years. The optimum flow rate across working faces is the key criterion selected.

Feb 23, 2014

By N. P. Reddy, Y. J. Wang

Stall or aerodynamic stall of axial flow fans has long been recognized as an important operational problem in mine ventilation. To develop a technique for characterizing fan stall in multiple fan ventilation networks, a research project was initiated through the Generic Mineral Technology Center for Mine Systems Design and Ground Control. Considering that fan stall is related to multiple operating points, this paper discusses a numerical model for multiple fan ventilation networks, and numerical methods for solving multiple networks solutions. It is hoped that the results of this project will lead to an innovative method of ventilation network analysis and simulation, thus preventing stall.

Jan 1, 1993

By Y. J. Wang

Stall or aerodynamic stall of axial-flow fans has long been recognized as an important operational problem in mine ventilation. To develop a technique for characterizing fan stall in multiple-fan ventilation networks, a research project was initiated through the Generic Mineral Technology Center for Mine Systems Design and Ground Control. Considering that fan stall is related to multiple operating points, this paper discusses a numerical model for multiple-fan ventilation networks, design of the experimental setup for two-and three-fan ventilation networks, and numerical methods for solving multiple networks solutions. It is hoped that the results of this project will lead to an innovative method of ventilation network analysis and simulation, thus preventing stall.

Jan 1, 1991

By Peter Hornby, Maurice Craig, Franklin G. Horowitz, Don Bone

We have developed a high-performance, flexible scheme for interpolating multi-dimensional data. The technique can reproduce exactly the results obtained, for example, from Ordinary Kriging and related techniques in 3D, or from Thin-Plate Splines (Briggs' minimum-cuwature algorithm) in 2D. Moreover, com- pared to traditional implementations of these algorithms, our method enjoys large computational-cost savings. The new approach produces an interpolation that obeys a Partial Differential Equation (PDE). The PDE may arise from physically based arguments, but its form can vary widely. It might be specified only implicitly (as through a Model Variogram), or be nonlinear (although a performance penalty could then apply). While a formal equivalence between Kriging and Splines has been known for some time (Matheron, 1980), the present derivation, from radial basis functions, further illuminates this connection. Thus, for example, we can make explicit the PDEs that underlie some of the Model Variograms most often used in Geostatistics. Besides its practical utility, the work thereby ac- quires a theoretical interest.

Jan 1, 1996

By S. Tafazoli, D. Cooper, I. Bell, S. Nouranian, B. Sameti, M. Ramezani

"Image-based rock fragmentation sensing in mines and quarries includes an important rock boundary delineation step, commonly referred to as rock segmentation. This paper presents an artificial intelligence-based solution to this challenge. The proposed technique encodes prior knowledge of previously analyzed images into mathematical/statistical models. Human-labeled images are used as inputs to train neural networks through an optimization process. The networks can then be used in real time for rock delineation. To build the models, special deep artificial neural networks are used as a pixel classifier. The proposed classifier labels each pixel (edge, rock or fine) by analyzing a plurality of pixels within the image. Advances in machine learning allow the network to contain many parameters. The increased number of parameters is a strong factor in the classifier’s ability to correctly classify each pixel. Deep learning-based segmentation, combined with 3D imaging followed by post processing, provides a unified fragmentation sensing solution. Results from automatic segmentation are compared to human labeled segmentation using the percentage passing curves for 64 rock images. INTRODUCTION Mines and quarries can see significant productivity and performance benefits by controlling material sizes (McKee, Chitmobo, & Morrell, 1995; Sellers & Gumede, 2012). During the past decade, image-based fragmentation analysis has been applied to estimate rock size distributions in order to optimize procedures in mines and quarries. Using a roving camera and operator assisted analysis Maerz, Franklin, and Coursen (1987) measured the size distribution of the blasted rock and eliminated the need for manual sieve analysis. Since then, many others have introduced automated and manual methods for fragmentation analysis and improved upon existing approaches (Girdner, Kemeny, Srikant, & McGill, 1996; Smith & Kemeny, 1993; Palangio, Palangio, & Maerz, 2005; Tafazoli & Ziraknejad, 2009; Raina, 2013). In image-based fragmentation, rock boundaries are identified in the image, and an image scaling is applied to transform rock pixel sizes into real world dimensions. Usually geometric references, such as regularly shaped objects (discs and basketballs) (Siddigui, Ali Shah, & Behan, 2009), or the known size of an excavator bucket (Zeng, Chow, Baumann, & Tafazoli, 2012), are used to determine the proper scaling factor. In recent years, 3D imaging and sensing have also been incorporated to improve rock delineation. Specific methods include using camera-laser combinations and stereo imaging to measure rock fragmentation on conveyor belts (Noy, 2013; Thurley, 2013; Dislaire, Illing, Laurent, & Pirard, 2013) as well as portable fragmentation analysis devices with 3D imaging sensors (Sameti, et al., 2014)."

Jan 1, 2018

By Donald C. Moore

Introduction Asamera Minerals (US) Inc. and its joint venture partner, Breakwater Resources Ltd., discovered ore grade gold mineralization on their 20 km2 (5000 acre) Wenatchee, WA land position in February 1983. Due to the high grade nature of the discovery ore and the known reserves of ore in the "B Reef' and "B West" zones previously outlined by other companies, a decision was made to construct a mine/mill operation near the known ore occurrences. Further drilling in the discovery area quickly expanded known gold occurrences to more than 3.6 Mt (4 million st) with tentative in-place ore grade of 7 g/t (0.25 oz per st) and minor silver values. Based on existing knowledge of the ore body and the rapidly increasing ore reserve, a decision to build a 1.8-kt/d (2000-stpd) mine and mill complex was made in the second quarter of 1983. A schedule was devised to begin immediate mine development, shaft sinking, environmental and land use permitting, and mill and tailings dam construction (Fig. 1). Meeting the scheduled startup date, April 1, 1985, required a fast track schedule in all areas. To this end, Asamera purchased the Oracle Ridge Partners concentrator. This was an assemblage of new equipment designed for use as a copper concentrator in southern Arizona. The purchase contained all of the major mineral dressing equipment - crushers, screens, rod and ball mills, etc. and an engineering package. It did not include most of the other required items, such as buildings, conveyors, pipelines, tanks, and pumps. At the same time, core samples were sent to two independent process development laboratories for initial flowsheet development. Due to the refractory nature of the carbonaceous ore, cyanide leaching was not feasible. Flotation was selected as the concentration process. Further testing showed that autoclaving of the flotation concentrate followed by cyanidation would result in overall recovery of about 85% gold. A mine manager was hired to begin assembling an operations staff, hire an environmental consulting firm, and begin mine development. Environmental and land use concerns were major obstacles due to the mine's close proximity to a city of 20,000 people. These concerns had to be rapidly defined so as to mitigate any adverse impacts from and mining processing operations. Baseline data dealing with weather, air and water quality, and sound were measured before start of mine construction. Concentrator and flowsheet development remained static until October 1983 while definition drilling and mine development proceeded. In late October, a process engineer was hired to coordinate development of a process flowsheet, purchase the remainder of the concentrator equipment, prepare a concentrator construction contract, finalize concentrator detail engineering, and combine environmental and process requirements with a tailings dam design. Process development There were only 17 months remaining to mill start up from the hiring date of the process engineer. Therefore, the process flowsheet had to be finalized rapidly. To accomplish this, samples of drill core from the highest grade (and therefore potentially the most commercial) ore zones were sent to an outside metallurgical laboratory to confirm beneficiation tests on the flotation process. Test results again showed that flotation would provide about an 86% gold recovery. Therefore, all further testing was concentrated on flotation and autoclave/cyanidation of flotation concentrates. Focusing on a well known process such as flotation was important in accomplishing the rapid design and construction of the concentrator. If, during these next phases, we were continually changing design concepts, layout, and process flow, the mill startup would have been delayed many months. Once a process flowsheet is selected the process engineer must obtain the process criteria needed to design the beneficiation system. For example, it was known in early December that the Oracle Ridge rod and ball mills were too small to grind 1.8 kt/d (2000 stpd) of Wenatchee ore. A decision had to be made to purchase a large, used ball mill and convert the Oracle Ridge ball mill to a rod mill. The process engineer must be cognizant of the process criteria needed to size and select equipment. If not, the process engineer must use the professional services of the equipment manufacturing companies to review the requirements that the equipment is asked to perform. For the Wenatchee system, this resulted in the adaptation of a ball mill to a rod mill with a weight limit of grinding rods to protect the mill bearings and drive trains. When a decision is required, the process engineer has to present the facts and options in a manner that allows a rapid decision. This information must include costs, equipment availability, and effect on the construction schedule. At the Cannon mine, there were process development details that resulted in decisions similar to the ball mill purchase. These included an increased flotation residence time from eight to 25 minutes, an increased thickener area requirement, a high pressure tailings pumping system, and area constraints in plant layout. All of these decisions had to be timely and required assistance from manufacturers' service engineers, and knowledge of the alternate costs and effects on construction completion. Equipment procurement It was decided in early 1983 to build the ore milling facility with Oracle Ridge equipment, augmenting it with used equipment

Jan 2, 1989

By D. C. Moore

The decision to proceed on a "fast track" construction project is not" without risks as well as rewards. An understanding of some of the risks prior to start of the project will maximize the rewards. This paper describes the research, development, procurement, engineering and construction of the Asamera Minerals cannon Mine concentrator. This fast track project was accomplished in 20 months. Special attention is paid to the risks encountered and the steps taken to ameliorate them.

Jan 1, 1988

By Bruce McKinstry

INTRODUCTION In June of 1992, the Bureau of Reclamation, United States Department of the Interior, awarded the contract for construction of the Sixth Water Aqueduct to the Fedrick-Redpath Joint Venture. This aqueduct, a segment of the Diamond Fork Power System, Central Utah Project, diverts water from Strawberry Reservoir into Sixth Water Creek and, when complete, will replace the old Strawberry Tunnel which was driven in the early 1900's. The new aqueduct is being built primarily as a result of deterioration of the old tunnel, but will also have a higher capacity and more positive control than the old tunnel as well as the capability to incorporate a turbine into the system at a later date. The Fedrick-Redpath Joint Venture is comprised of C.R. Fedrick, Inc. of Novato, California and J.S. Redpath Corporation of Tempe, Arizona. Fedrick, with its experience in pipelines and heavy construction, will construct the 4200 ft surface pipeline and flow control structure; Redpath, the managing partner, performed the underground work consisting of a 600 ft vertical shaft and 3300 ft tunnel. The project is located in the Uintah National Forest, approximately 20 miles east of Provo, Utah at a mean elevation of 7000 feet above sea level.

Jan 1, 1995

By Malcolm J. A. Swallow

In June 1997, Mount Polley Mining Corp., a division of Imperial Metals Corp., completed an 18-kt/d (20,000 stpd) gold-copper mine in central British Columbia. Fast-track construction and extensive off-site construction were combined with an aggressive project schedule to build the mine in one year. This was three months ahead of schedule and 7% below the original budgeted cost of C$123.5 million (US$86 million). The Mount Polley Mine was the first of a crop of new open-pit mines in British Columbia. The Mount Polley deposit has been explored since the mid-1960s when it was known as the Cariboo Bell property. From 1988, Imperial Metals completed drilling and metallurgical testing on the deposit. This led to a positive feasibility study and the issuing of a Mine Development Certificate in 1991. The project was later shelved due to falling metals prices and the strength of the Canadian dollar. In late 1994, Imperial merged with Bethlehem Resources Corp., bringing a strong project team to the company. The deposit was then re-evaluated, ore reserves revised and additional metallurgical testing was performed. The result was a revised project plan. It indi¬cated that a financially feasible gold-copper mining op¬eration could be constructed at Mount Polley operat¬ing at 18 kt/d (20,000 stpd). In May 1996, an agreement was reached with Sumitomo to jointly fund and develop the project. By early 1996, final plans and permits were being prepared for construction, scheduled to begin in June 1.996. On-site work commenced on May 28th, 1996 following lifting of the road restrictions. Mount Polley Mining acted as its own project manager. Construction was completed in June 1997. Plant runup took place in July and full production began in August. Through the use of off-site construction and the careful selection of contractors who cooperated to complete some 12 major contracts, it was possible to reduce the mine and mill construction time from 16 to 13 months. Off-site construction for all possible aspects of the work and the use of used milling equipment allowed significant savings in overall capital costs of construction. Total costs for the mine, mill and tailings dam equated to C$6,100/t/d of throughput. The mill design incorporates several innovative features that will aid maintenance and allow flexibility of operation. The operation is designed as a closed system and meets the latest environmental standards. Concentrate is shipped by truck to the port of Vancouver. Revenues for the mine come from the mine's production of about 3.1 t/a (100,000 oz/year) of gold and 10.8 kt/a (24 million lbs/year) of copper during the first four years of the 12-year mine life.

Jan 1, 1998

By D. Ofiara, M. Lewis

Tunnel Boring Machines (TBMs) have been used in mining in decades past, but their use has been limited and sporadic. This has changed in recent years, with TBMs being used at Stillwater Mine, Grosvenor Coal Mine Slopes, Sirius Minerals potash mine, and more. These machines are all full face, circular TBMs—a design that has thus far have been unable to tackle a larger issue for mines: typically a flat floor is needed for mining vehicles to traverse. A novel type of non-circular boring machine is now answering the need to quickly reach underground ore bodies while cutting a rectangular profile in hard rock. This cross section allows for use of typical mine trucks and other rubber-tired mine vehicles. The machine uses disc cutters to cut the rock, and has a support structure similar to an open type TBM; however, the cutting geometry is entirely different. The machine is currently cutting an access tunnel at a silver mine. This paper reviews the design and operation of the novel noncircular tunnel boring machine, and describes possible future adaptations to provide safe, sustainable mine development.

Mar 2, 2022

By Arif Emre Dursun

The aim of this study is to present hazard classifications of location, type, and causes of accidents in Turkish coal-extracting industries using Analytic Hierarchy Process (AHP). In this study, fatal mine accidents were analyzed by pairwise comparison and weighting, and the most important hazards were identified by determining the effective main and sub-criteria among location, type, and causes of accidents. For this purpose, 1st, 2nd, and 3rd level hazards consisting of location, type, and causes of accident were determined by using the data of fatal mine accidents in underground and open-pit coal mining in Turkey between the years of 2010 and 2020. And then the data were categorized, and each category was prioritized using the AHP technique. According to the weights calculated by AHP, the most dangerous main criteria at 1st level hazards in underground coal mining is ventilation operations (0.363), while the most dangerous sub-criterion at 2nd level hazards is firedamp explosions and other gas accidents (0.409). On the other hand, in open-pit coal mining, the most dangerous main criteria at 1st level hazards are slopes and benches (0.575), while the most dangerous sub-criterion at 2nd level hazards are landslides (0.429).

Dec 30, 2023

By Arif Emre Dursun

The aim of this study is to present hazard classifications of location, type and causes of accidents in the Turkish coal-extracting industry using the analytic hierarchy process (AHP). In this study, fatal mine accidents were analyzed by pairwise comparison and weighting, and the most important hazards were identified by determining the effective main and sub-criteria among location, type and causes of accidents. For this purpose, first-, second- and third-level hazards consisting of location, type and causes of accident were determined by using the data of fatal mine accidents in underground and openpit coal mining in Turkey between 2010 and 2020.

May 1, 2024

By J. W. C. Wong, T. A. Songberg, S. D. Miller, J. J. Jeffery

Natural degradation of cyanide has been widely used by the gold mining industry for removal of CN from cyanidation processing wastes. However, little documented study has addressed the decay and fate of cyanide within residue storage ponds. 'fhis paper describes a study on the cyanide behaviour in a residue storage pond at the Boddington Gold Mine in Western Australia. Depth profile samples were collected from the active residue storage to determine the distribution of CN forms and complexing metals throughout the settled residue.

Jan 1, 1991

By W. M. Schafer

The risk that water quality will be degraded by mining activity can be evaluated using risk analysis techniques. Water quality impacts can occur where water-rock interactions with tailings, waste rock, or leached ore lead to increased loading of constituents into surface or groundwater. Constituent loads contributed by mining facilities are determined by the migration route and chemical evolution of mine water. Mass load contributions from mines can be determined by estimating the prototype pore water in contact with mining waste, predicting the rate and timing of flow, assessing the degree of geochemical attenuation, and modeling chemical mixing with natural surface or groundwater. Mining facility siting and design measures can alter the chemical evolution of mine water by varying the quantity or quality of flow. Stochastic risk management techniques provide a powerful tool for quantitatively identifying the environmental consequences of various siting and design alternatives.

Jan 1, 1998

By Hugo J. Garcia, M. C. Fuerstenau, D. M. Lupan, J. L. Hendrix

Biodegradation of cyanide by microorganisms isolated from solids previously exposed to cyanide has been investigated. The anaerobic cyanide biodegradation showed good, short-term removal of cyanide in the presence of nutrients (medium A). This system retained metabolic activity at cyanide concentrations up to 300 ppm at pH 10.5. Microscopic examination of stained specimens revealed that the bacteria were Gram-negative, rod-shaped bacilli. Strains capable of cyanide decomposition were identified as Pseudomonas and Alcaligenes. The kinetics of biodegradation were found to be first order with respect to cyanide concentration, and the overall reaction rate constant is k = 0.102 day-1. Studies with Na14CN showed that 17 % of 14C transformation went into the cells, 18 % into carbonate and 47 % into bicarbonate.

Jan 1, 1995

By B. M. Sadashiva Murthy

Increasing quantities of nutrients and pesticides in agricultural runoff in recent years has caused the more developed western nations to become concerned about diffuse agricultural pollution. Thus, the problem of diffuse pollution is of greater importance and concern for any integrated water quality management programme. The above mentioned sources and activities causing pollution to groundwater cannot be completely avoided. The best solution is to entail a firm understanding of the principles of solute transport through porous media. The complex factors that control the movement of contaminants in porous media and the resulting behavior of contaminant plume are usually intricate to assess because of interaction of many factors such as dispersion, advection, sorption, degradation, volatilization, etc. As accurate quantification of solute under field conditions is inherently difficult, the fate of nitrate and phosphate have been analyzed in laboratory column and channel studies. From the analysis of the breakthrough curves, the dispersion co-efficient for nitrates and phosphates through sandy soil was found to be 0.262 m2/d and 0.114 m2/d for column studies, 0.321 m2/d and 0.231 m2/d for channel studies respectively. The column studies revealed that the concentration of nitrates and phosphates increased steadily in the first few days (around 5 days) and then it increased rapidly after 8 to 10 days. However, it attained equilibrium after 20 days. Similarly, the channel studies revealed a steady increase in concentration of nitrates and phosphates in the first few days (1 to 2 days) and rapid increase up to 15 days and there after it attained equilibrium. In the study, one-dimensional analytical model has been developed which include the advection, dispersion, and a characteristic term called ?total elimination rate?. The comparative study of column and channel studies, and model output (in which the term total elimination rate ?K? is considered as zero) exhibited a variation of 30 to 50 % in leaching characteristics of pollutants (nitrates and phosphates).

Jan 1, 2008

By Dennis A. Fenton

This paper presents some techniques and data required to design large ball mills. The advent of larger size mills leads to consideration of the gearless drive as a practical solution to utilize large horsepowwers. The particular shell structure under consideration is subjected to thermal as well as magnetic loads. The magnitude of the inertia, magnetic and shell temperature characteristics have a very significant effect on the design and performance of the hydrodynamic pivoted shoe bearing. Particularly since these bearings have lower frictional resistance properties than hydrostatic trunnion tee rings. The structure of the mill is designed for long life. Parameters involved with the fatigue life of the structure are discussed together with some of the more important aspects of the design.

Jan 1, 1975

By Edward Finch, William F. Riggs

Selectivity and recovery of many industrial minerals can be directly affected by the carbon length, degree of unsaturation, and melt point of fatty acids used as collectors. Examples of several modifications are provided based on actual experiences of commercial applications. A review of recent history indicates that fatty acid collectors are applicable from C9'C18 in carbon length, however, not for all minerals. The mesh size, density, and surface characteristics of the particular mineral, as well as other related operating conditions, are important in selecting the correct fatty acid configuration. A review of some past programs are submitted as a guideline in the selection of fatty acids and supported by isolated, successful examples demonstrating the effect of carbon length and unsaturation.

Jan 1, 1986