Search Documents

By Janusz S. Laskowski

The most important type of potash ores, sylvinite, contains sylvite, halite and a small percentage of insoluble gangue [sulfates (anhydrite), carbonates (dolomite), and clay minerals]. Primary normal long-chain amines are exlusively utilized to float sylvite from halite, but since mines are also adsorbed by insoluble slimes, the process requires prior desliming. This is carried out either by mechanical means, or by flotation of slimes and blocking off the adsorption centers on clays with the use of polyelectrolytes. Fractional crystallization is employed to produce fertilizer grade KC1 from disseminated ores with a high content of slimes. An extender oil is needed in addition to mine to float coarse sylvite fractions. The process is carried out in a saturated brine at mine concentrations exceeding the solubility limit and is strongly affected by temperature fluctuations. All these important features, which make this process differ from a conventional flotation, result from a high electrolyte concentration.

Jan 1, 1994

By N. Sahin, M. Can, Z. Ekmekçi, Y. Öztürk, Ö. Biçak, I. B. Çelik, B. Kocabiyik

"In this paper, a case study from Çayeli Bakir Isletmeleri A.S. (Rize, Turkey) about the selective flotation of copper minerals from sphalerite is discussed. Çayeli Cu-Zn Sulfide Ore contains different ore types, such as yellow ore, clastic ore, bornite-clastic ore, bornite-yellow ore, and black ore. For some of these ore types, selective flotation of copper and zinc is very difficult presumably due to presence of secondary copper minerals such as bornite, chalcocite and covellite, and also surface oxidation. These factors affect Cu-Zn selectivity due to activation of sphalerite particles in the ore during the process. The main objective of this work was to improve Cu-Zn selectivity by optimization of the pulp chemistry for different ore types of Çayeli ore. After preliminary flotation tests investigating effects of different chemical conditions, a plant survey was performed to determine the plant performance and sources of the problems when problematic bornite-clastic ore is treated in the plant. Various chemical conditions are tested in the laboratory scale test for better depression of sphalerite in copper flotation circuit. Combination of Na2S+ZnSO4+MBS was found to be the most effective depressant scheme. INTRODUCTION Ore variability is one of the most important factors affecting performance of a process plant both in short and long term planning. The geometallurgical modelling becomes a common tool to determine ore variability problems and develop the most efficient solution during life of mine (1, 2). Flowsheet design and equipment selection and sizing are usually done based on the results of ore variability test works. However, in some cases ore variability may not be foreseen during the design stage and therefore the solutions should be developed based on the existing flowsheet and equipment in the plant. In this situation, ore characterisation, problem statement and diagnostic testing should be applied step by step. The problem could be due to changing feed grade, mineralogical characteristics, grindability and surface characteristics when flotation is involved. The variability in feed grade with fixed mineralogy can be handled with relatively simple modifications (i.e. adjusting throughput or equipment capacity) in the plant. Variability in ore mineralogy is the most complex and difficult problem to tackle. Because, mineralogical variations could bring variations in mineral composition, texture and liberation. These variations can potentially lead to the variations in grindability of the ore and flotation behaviour. Variations in grindability are usually managed by optimization of operational parameters in grinding circuit, as it would be costly to replace the existing equipment in the circuit (3). The variations in flotation behaviour are mainly due to variations in mineral types and distribution, texture and surface oxidation. One or all of these factors could be observed in a flotation operation. Therefore, a comprehensive investigation both in plant and lab scale should be conducted for definition of source of the problem. The testwork to solve the problem and retrieve the performance is planned and conducted depending on the source of the problem (4, 5)."

Jan 1, 2017

By A. Raviprasad, B. Das

Copper ore from the Rakha Copper Concentrator (India) was successfully floated using LIX-65 NS as the collector. The beneficial role of this reagent was clearly demonstrated in hatch-flotation tests. From a feed containing around 1% Cu, it was possible in a single-stage flotation to obtain a 23.7% Cu concentrate with a recovery of more than 90%. The plant now uses rougher, scavenger and a two-stage cleaning process. The tests demonstrated that LIX-65 NS is superior to conventional xanthate for the recovery of copper from the Rakha ore.

Jan 1, 1997

By P. Somasundaran, H. S. Hanna

The separation of minerals such as apatite and scheelite by flotation from other salt-type minerals such as calcite is extremely complex owing to the close similarity between their physicochemical properties. In this paper, properties relevant to flotation such as crystal structure, solubility, surface charge and adsorption behavior of important salt-type minerals are examined along with the role of inorganic modifying agents such as silicates and polyphosphates and organic modifying agents such as starch and tannin. Flotation characteristics of these minerals are then reviewed and selected separation problems involving salt-type minerals are discussed.

Jan 1, 1976

By W. K. Tolley, D. G. Kotlyar

Silver is an economically important component of many complex, massive sulfide ores. The beneficiation of this type of ore is now almost entirely accomplished by flotation. Silver recovery is often low, and little is known about the flotation behavior of the silver-bearing minerals. Floatability studies were conducted using silver-bearing tetrahedrite and lead-zinc ore. The effects of xanthate-collector concentration, conditioning time, potentiostatic control of the mineral potential and control of the pH on mineral floatability were evaluated. The floatability of the silver-bearing minerals was shown to depend on collector concentration and mineral potential. The effect of controlling the mineral potential during the flotation process is discussed.

Jan 1, 1996

By D. G. Kotlyar

Silver is an economically important component of many complex, massive sulfide ores. Current beneficiation for these ores is almost entirely by flotation. Silver recovery often is low, but little is known about the flotation behavior of the silver-bearing minerals. Floatability studies were conducted using silver-bearing tetrahedrite and lead-zinc ore. The effects of xanthate collector concentration, conditioning time, potentiostatic control of the mineral potential, and pH on mineral floatability were evaluated. The floatability of the silver-bearing minerals was shown to depend on collector concentration and mineral potential. The effect of controlling mineral potential during the flotation process is discussed.

Jan 1, 1994

By Geoffrey Purcell

The flotation response to amine collector of quartz and the feldspars microcline and albite, of the pyroxenes augite and spodumene, and of olivine can be, explained by a physical adsorption model. Flotation decreases in the order given above, and the different behavior of the three groups is attributed to structural variations of the silicates, With sulfonate collector both chemical action and physical adsorption play their part in producing hydrophobic surfaces, and flotation increases in the order given.

Jan 1, 1966

By James S. Browning

Extensive deposits of kyanite occur in the southeastern United States, The reserves of these deposits, if developed, are adequate to supply the United States with 35-mesh kyanite concentrate:; for many years at the present-rate of consumption, According to Espenshade and Potter,1 the kyanite-quartz rock type deposits in this area contain about 100 million tons of ore averaging 10 to 30 percent kyanite. The tonnage of kyanite-bearing gneiss and schist is, much larger than the tonnage of kyanite-quartz rock, but the kyanite gneiss and schist are appreciably lower in grade. The largest deposits of kyanite-quartz rock are in the Farmville district, Virginia, and Kings Mountain district, North Carolina South Carolina, and at Graves Mountain, Georgia. Of the known deposits, only four were being mined for kyanite in 1967. These deposits are near Farmville and Dillwyn, Va., Clover S. C., and Washington, Ga. Production of kyanite and synthetic mullite increased substantially in 1965.2 Output of, domestic kyanite concentrate increased by 14 percent in 1965, establishing a record high for the fifth consecutive year. Estimated annual consumption of kyanite minerals and synthetic mullite was in excess of 100,000 tons. The manufacture of mulatto refractories accounts for most of the kyanite minerals consumed annually, but non-refractory uses are expanding.3 Most mullite refractories are used as furnace linings in metallurgical and glass manufacturing furnaces. The remainder is used largely for kilns, kiln furniture, and saggers by the ceramic industry. Small quantities of kyanite without calcination are used as a source of alumina in the manufacture of glass, electrical and chemical, porcelain, pyrometer tubes, and in the form of kyanite concentrate to increase the alumina content of fireclays. Kyanite is used to improve workability, increase strength, and to compensate for firing shrinkage in floor and wall tile and other ceramic products.

Jan 1, 1968

By S. Meng, R. Jin, W. Hu

In alkaline pulp, galena is depressed by sodium carboxymethyl cellulose (NaCMC), while Cu(II) -activated sphalerite exhibits a high floatability so that satisfactory separation can be achieved. In addition to hydrogen bonding, chemical bonding of NaCMC with galena is confirmed by infrared (IR) spectra; only hydrogen bonding is involved between NaCMC and Cu(II)-activated sphalerite. It is also found that the greater the degree of substitution and polymerimtion of NaCMC, the stronger the depressive effect of NaCMC and that lower stirring speed favors the depression.

Jan 1, 1988

By Ruiren Jin

In alkaline pulp, galena is depressed by sodium carboxymethyl cellulose (NaCMC), while Cu(II)-activated sphalerite exhibits a high flotability so that satisfied separation can be achieved. In addition to hydrogen bonding, chemical bonding of NaCMC with galena is confirmed by IR; only hydrogen bonding is involved between NaCMC and Cu(II)-activated sphalerite. It is also found that the greater the degree of substitute and polymerization of NaCMC, the stronger the depressive effect of NaCMC and that lower stirring speed favors the depression.

Jan 1, 1987

By O. Ofor

Coal fines of less than 0.5 mm particle size, discarded as too fine for gravity separation, were subjected to flotation tests at varying pH and temperatures using modified dosages of kerosene as oil phase and methylisobutylketone (MIBK) as frother. Optimal coal recovery of over 74% was obtained using 200 kg kerosene and 4 kg MIBK per ton of coal fines at a pH of 9.7 and an ambient temperature of 26° C. The coal concentrate obtained under these optimal recovery conditions assayed 9.10% ash, 0.35% sulfur and 0.011% phosphorus, representing reductions in the ash, sulfur and phosphorus contents of approximately 75%, 43% and 8.3%, respectively. Its gross calorific value was 32.9 MJ/kg, its percentage of volatile matter measured 30.6 and the fixed carbon content was 66.3% (d.a.f). Caking tests showed the optimal concentrate has a standard welling number of 1 and is a Gray-King coke type C. These results show that the optimal flotation product could be utilized for such industrial purposes as steam raising or for processing in gasworks, but it would be unsuitable for metallurgical coke production.

Jan 1, 1993

By X. M. Yuan

In the flotation of Zn-Pb ores, sphalerite is floated following copper sulfide activation. In this type of sulfide ore, pyrite is commonly treated as a gangue, and poor selectivity between sphalerite and pyrite/quartz is often reported. But pyrite may also appear in association with gold, and flotation of such auriferous sulfides is of great importance in many countries (e.g. South Africa, Australia). In the cationic flotation of sulfide ores with dodecyl amine, sphalerite can be floated while depressing quartz and pyrite. While in a well-aerated pulp in the presence of lime (especially after oxidation with H2O2) the cationic flotation of pyrite is depressed, oxidation of pyrite in the presence of Na2S makes it floatable with amines even in very alkaline environment.

Jan 1, 2002

By Corneille S. Ek

Flotation of several copper and lead-zinc ores has been carried out with mercaptobenzothiazole (MBT) as promoter. The results of laboratgory batch flotation tests have been compared with those obtained when using more common collectors like xanthates or dithiophosphates. It generally appears that MBT is an effective collector of all the sulfides, including pyrite, but that high selectivity is rather difficult to attain, except for gangue drop-out. Some kinetic tests have been performed to check the froth production rate by MBT as compared to other collectors.

Jan 1, 1995

By M. A. D. Azevedo

The effect of pulping reagents on the flotation de-inking of laser printed wastepaper was investigated with regard to the removal efficiency of toner and mineral filler particles for different pH values. These results show that caustic pulping causes the toner to be released from the fibers at larger particles sizes. On the other hand, acid pulping not only causes the toner to be released at smaller particles sizes but also increases the concurrent flotation removal of mineral filler particles. It was experimentally observed that the froth generation and stability during flotation were improved for acidic pH values.

Jan 1, 1997

By W. D. Eddy

Topaz is a fluorine-bearing aluminosilicate mineral of the kyanite-sillimanite group. The formula has been given as Al2SiO4(F,OH)2, [Al(F, OH)]2SiO4, or 2Al2O3?2Al(F, OH)3SiO2. Topaz is generally considered a semiprecious-to-precious gem mineral, but it is a fairly common minor constituent of granites. In 1937 the U.s. Geological Survey reported an occurrence of massive topaz in the 3 Brewer gold mine, Chesterfield County, S.C. Over the next 8 years considerable research was done on topaz to establish its properties and to determine possible end uses The first reported shipment of ore was in 1939 Peak production was reached in 194412, and output then began declining until the mine closed in 194913? During World War II topaz was used in refractories, as a flux in steel mills, and in the manufacture of borosilicate glass 14. The main advantage of using topaz over kyanite and sillimanite in refractory use was that calcined topaz converted to over 95 percent mullite (3A1203 .2Si02) while calcined kyanite or sillimanite contained only 88 percent mullite15. However, a major draw-back to utilization of topaz is the evolution of fluorides during calcination. In 1973 the Geological Survey reported that topaz occurred in probable commercial quantities in at least two domestic locationsl6: the Brewer area of South Carolina and a location in Colorado. The literature also indicated that progress had been made in controlling fluorine-bearing fumes. This research has progressed to the state where valuable fluorine compounds are being recovered on a commercial scale 17. Thus, a major obstacle to utilization of topaz appears to have been resolved. The Bureau of Mines under its program of advancing minerals technology initiated a project to study techniques for the concentration of topaz from disseminated materials. The objective of the study was to determine those techniques that would be used to produce topaz concentrates that could be utilized as a source of fluorine and mullite.

Jan 1, 1977

By A. Hajati

The main purpose of this study was to find the optimum values for factors affecting the Zn recovery rate using oxine or dithizone as a chelating agent collector during flotation in a Hallimond tube. Eight control factors, including four levels of pH, oxine/dithizone, corn starch, sodium thiosulfate, sodium citrate, sodium silicate, conditioning and floating durations were considered in a Taguchi experimental design technique. An L32 orthogonal array was applied to determine the signal-to-noise (S/N) ratio. Analysis of variance (ANOVA) was used to determine the optimum conditions and the most significant parameters affecting the reaction rate. Analysis of the experiments using the Taguchi approach indicated that pH had the highest contribution to the recovery rate of zinc oxide particles. The results showed that the recovery rate of zinc increased by 43.4 ± 3.0% and 24.9 ± 3.2% using oxine and dithizone, respectively, under optimum conditions with a confidence level of 90%.

Jan 1, 2010

By Z. H. Xie, D. S. He, W. M. Xie

China has rich phosphate rock resources, but with their continuous depletion, the rich ore resources have become increasingly scarce, which makes the exploration of collophane more important. Medium- and low-grade phosphate rock cannot be utilized until their impurities have been removed through mineral processing. However, due to the similar physical and chemical properties of dolomite and phosphorus minerals, the separation of dolomite from phosphate

By Donald S. Skufca

This chapter focuses attention on major factors pertaining to plant design and general arrangement of equipment. Considered are efficiency of operations, coordination of maintenance and repairs, plant testing of reagents and possible future plant expansions. The design and general arrangement of equipment considers accessibility for maintenance and isolation for repairs, minimum personnel for operations and cleanup, safe working conditions with minimum interruptions to operations. The constant introduction of new reagents requires eventual plant testing and the manner of isolating a “line” or part of the facilities to allow comparisons in the testing of new reagents is discussed. As technology improves and process changes occur, additional equipment or plant expansions are inevitable. Space for these eventualities must be considered while the general arrangement drawings are in the development stages.

Jan 1, 1986

By Dexter C. Hatch

At MacIntyre Development of the National Lead Company, Taha s, New York,, the flotation plant was set up to recover ilmenite from the finer size fraction of the ore that cannot be efficiently treated in the main gravity-magnetic separa¬tion process. It was later expanded to handle the reground middlings from the tables wetherill magnetic separators. The ilmenite-magnetite ore is ground to minus 20 mesh in five 6 x 12 ft. rod mills in closed circuit with DSM screens. The minus 20 mesh screen undersize is pumped to four parallel sections each consisting of two rougher wet-magnetic separators and one cleaner separator for magnatite removal. The screen undersize from the fifth section is distributed to all four sections. The magnetite removed in the roughers is pumped back to the cleaners and the cleaner magnetite is dewatered in rake classifiers and carried by belt to the winter plant or the stockpile area. The nonmagnetic sands from rougher and cleaner magnetic separator are sized for table feed in eight pocket hydraulic sizers. The slime overflows from the Crocketts, the sizers, and the magnetite rakes are collected and pumped to three-inch cyclones for thickening and desliming. The cyclone underflow is the principal flotation plant feed.

Jan 1, 1962

By T. Negeri, Y. Breau, M. Plante, A. Orumwense

As part of a joint project on fine particle processing, sponsored by the Consortium de Recherche Minérale (COREM), Natural Resources Canada (NRCan) and Hydro-Quebec, two flotation plant circuits were sampled to identify and quantify the causes of mineral losses within several particle size ranges. Size distributions, size-by-size assays and global chemical assays (Cu, Zn, Fe, S) were determined for the major streams. Size distributions were measured in 13 classes by sieving, cyclo sizing (-45 µm), and laser beam diffraction analysis. BILMAT, a material balance computation software package, was used to optimise the sampling, to estimate the unmeasured variables, and to assess and improve the quality of the information generated. The methodology has been extended to correct cyclo sizer data and reduce discontinuities of up to 20% at the transition from sieves to cyclo sizer. The paper describes the methodology and the main conclusions emerging from material inventory of the flow sheets.

Jan 1, 2003