Search Documents

By Manoj Khandelwal, Minghui Liu, Jian Zhou, Kun Du

The waste rock and tailings backfill into the mined-out areas are the most effective method for solving the environmental pollution and surface disasters for nonferrous metals mines. In practice, the success and availability of backfill operations are dependent on the slurry fluidity and the strength properties of cement backfill. The transport of the slurry through the pipeline to the designated backfilling area relies on its eximious flow properties, while the appropriate strength of the filling body ensures the safe operation of the stope. In this paper, the effects of cement and aggregate types on the slurry fluidity and strength characteristics of cemented backfill are studied in detail, which are often ignored in other pieces of literature. Diffusivity is used as an indicator to evaluate the slurry fluidity. Various slurries whose concentrations ranging from 70%, 73%, 75%, 78%, and 80% are made with different aggregate ratios and cement-sand ratios are tested. It has been shown that slurry fluidity is inversely related to its concentration, but 78% is the “stopping point” for the deterioration of fluidity. The addition of rod-milled sand improves or worsens the cemented backfill (CB) strength depending on the amount of rob-milled sand. The uniaxial compression experiment results on 216 CB specimens produced by different combinations of influencing variables showed that CB specimens made from cement with superior mechanical properties have a higher uniaxial compressive strength (σucs). It has been also found that the effect of aggregate ratio on the CB strength is not singular, but works in conjunction with the curing time and the cement-sand ratio. The longer the curing time and the higher the cement content, the higher the CB’s σucs. To avoid the time-consuming and costly problem of obtaining the strength of the CB from indoor experiments, an SVR model capable of predicting the uniaxial compression strength of CB specimens is proposed, which is optimized by genetic algorithm (GA) and particle swarm optimization (PSO) algorithm. The results of the three performance indexes (MAPE, MSE, and R2) show the superior performance of the GA-SVR and PSO-SVR models and the agreement of the predicted results with the experimental results, which indicate that these two models can accurately predict the σucs of CB.

Feb 3, 2022

By D. Arku

The increased use of sensors to facilitate automation has led to an explosion of data. As data sets grow in size, their use becomes more complex. Therefore, there is an incentive for reducing the size of the datasets, as long as this does not compromise information gleaning. With this in mind, this project explored basic aggregation as a viable alternative to amassing large amounts of data. The goal of the project was to determine if one would arrive at different conclusions had they analyzed aggregated data instead of raw data. In a mine, operational data is typically used for tracking process statistics, correlation between factors, autocorrelation and multivariate models (for a factor of choice). Therefore, this project compared results from such analyses when it was conducted with aggregated data (AD) with the results of analyses conducted with raw data (RD). The data consisted of one-minute-apart readings from a semiautogenous grinding (SAG) mill on the horsepower, feed rate (tons per hour), rotations per minute (rpm), noise, recycle (tons per hour), density (% solids) and bearing pressure (psig). This data was aggregated by averaging five and 10 continuous (one-minute) observations. Changes in statistical measures between the two approaches were typically within 5% of each other. Differences in correlation coefficients between RD and AD(s) were also within this range. Autocorrelations present within RD were preserved in AD, as long as the time lags were scaled for the amount of aggregation. Regression and neural network models were also developed for power consumption. The prediction performance of developed models was similar whether one used raw data or aggregated data. Overall, it appeared that aggregating the data based on 5- or 10-minute time spans would not have resulted in conclusions (from simple or complex analyses) being different from using raw data. In other words, whether one had used raw data or aggregated data, the conclusions would have been the same, suggesting that time domain aggregation, a common industry practice, is a good alternative to storing high-density data in this case.

By Robert A. Cummings, Madan M. Singh

In April 1984 a subsidence depression formed directly beneath a two-story frame residence, near Linton, IN, causing 2 ft of separation between the floor and walls, and damaging both the foundation and interior of the building. The Office of Surface Mining undertook the rehabilitation of the area under its emergency response program. This paper describes the investigation performed to determine the cause, severity, and extent of the problem. Abandoned mine workings were found approximately 55 to 60 ft below the house. Based on the findings, remedial measures were prescribed. An abatement program consisting of grouting the mine voids was recommended, and specifications prepared. These were implemented, and the area has been successfully stabilized.

Jan 1, 1986

By David Van Horsen

Big Creek Tunnel 2, constructed in 1912, is located in the Sierra Nevada Mountains of California, east of Fresno. It is horseshoe and circular shaped with a 3.6m (12ft) diameter and extends 6.6km (4.1mi). Historically, tunnel performance suffers from highly jointed rock and low cover. In 2003, leaks were observed surfacing through outcrops of highly jointed graniodiorite, and subsequently investigated by visual inspection, joint mapping, ground penetrating radar, and a water-tracing survey. Several grouting targets were identified as a result of these investigations. Cement grouting was used to fill void spaces, broken rock and open joints expected to exist behind the concrete and steel liners. Project work consisted of grout hole drilling through the existing concrete liners, and grout placement through squeeze packers supplied by standard grout hose and portable grout plants. Grout pressures were typically 20?30 psi. Grouting was completed in 16 days with a total of 1,550 sacks of Type II/III grout placed at the three likely leak source areas. No grout was observed exiting the tunnel and the leak was stopped.

Jan 1, 2008

By Thomas M. Hanna, John W. Anthony, Lee C. Atkinson

Ground water can pose major engineering and environmental problems to the new generation of large, deep gold mines currently being developed throughout the world. It is important that the potential magnitude of these problems be assessed early in the planning of such projects and that any necessary dewatering and environmental remediation programs be designed at least preliminarily in the feasibility stage. The assessment should begin with acquisition of hydrogeologic data during exploration drilling and be followed by carefully designed and analyzed aquifer tests. Once a sufficiently detailed conceptual hydrogeologic model has been defined, state-of-the-art numerical models should be used to estimate ground-water inflows to proposed pits and underground openings, to design and evaluate the potential effects of various dewatering schemes, to define specific environmental impacts, and to predict pore pressures in highwalls relative to slope stability. The modeling results will indicate which method(s) of dewatering will be most effective both technically and economically. If wells are used, it is imperative that they be as hydraulically efficient as possible. There are new methods of drilling and completing dewatering wells that can help assure maximum efficiency.

Jan 1, 1989

By E. Topuz, C. Patrick

Longwall face-to-face transfers can cost more than $100 per minute in lost production potential and $100,000 for personnel and supplies. Such high costs make extensive planning and control of the transfer process a critical necessity for the economic feasibility of longwall operations. Operations research techniques are used for the analysis and modeling of longwall face-to-face transfers. Transfer data has been collected from companies who operate, over 35%, of the total US longwall faces. Comprehensive sequence networks of existing longwall transfers were developed; simulation was used to generate models of transfers under Carving conditions; and the economic feasibility of tine-cost tradeoffs in the transfer procedure was investigated.

Jan 1, 1994

By Harry R. Price, Keith M. Swaffar

The Northeast Raw Water Tunnel transports untreated water to the Detroit Water and Sewerage Department's (DWSD) Northeast Water Plant where it is treated and distributed. The occurrence of a subsidence area which was attributed to the tunnel prompted the DWSD to have the tunnel investigated. After an extensive historical and geotechnical investigation, two access shafts were constructed along the alignment in the vicinity of the subsidence. Following completion of the shafts, the subsidence area was inspected in the wet prior to dewatering the tunnel. Upon the completion of dewatering, a dry inspection was performed. During the dry inspection, an area of significant distress was encountered where sand and silt were boiling into the tunnel along with large volumes of groundwater. This distressed area was located 800m (1/2 mile) north of the original subsidence area. The tunnel was immediately refilled with water and an emergency repair program was planned and implemented. As a result of the distressed nature of the secondary tunnel liner, dewatering of the tunnel could not be performed until the secondary liner and the surrounding soils were stabilized. This paper presents a case history of both the investigation and the repairs of the Northeast Raw Water Tunnel including the various grouting and unique tunnel stabilization methodologies which were utilized.

Jan 1, 1987

By St. E. Deák

This paper focuses on maintenance of underground salt air curative quality using environmental friendly solutions. Possible ways to preserve its curative properties, in relation with the admissible salt air quality parameters, are analyzed. In situ investigations regarding microbiological impregnation in walls and the air inside the Romanian salt sanatorium were initiated. The results of a pilot project, which is in progress at Praid salt mine, are presented. After the end of the investigation at this site, investigations will continue in other Romanian salt mines, such as Slanic Prahova, Targu Ocna and Cacica.

Jan 1, 2006

By Jozef S. Stachulak

INTRODUCTION Conveyor belt fires represent a serious hazard in underground mines. This fact is well understood in most mining countries. The statistical data for Ontario mines (1) indicates that the majority of the conveyor fires occurred at the head pulley of the conveyor belt. The main emphasis for fire prevention and detection should then be concentrated at the drive pulley of the conveyor designed to transport non-combustible material. In the case of conveyor belt fires, it is of utmost importance to detect the hazard at an early stage, when the overheating has not yet reached the ignition point. Thermal noise detection sensors were installed in 1987 at several conveyor sites at Inco mines. PRODUCTS OF COMBUSTION THERMAL DEGRADATION OF CONVEYOR BELT Various investigations on conveyor belt fire hazards have been made in the past (2, 3, 4, 5, 6, 7). Several belt samples (6, 7) were subjected to thermal oxidative degradation. The belts used in these tests were neoprene, polyvinyl chloride and styrene-butadiene rubber (6). About 70 different compounds were identified in the volatile thermooxidative products. As expected, hydrogen chloride was the major toxic product formed, accompanied by relatively low quantities of other toxic compounds such as carbon dioxide, carbon monoxide, sulfur dioxide, carbon disulfide, hydrogen sulfide, benzene, chloroprene, cresols, chloroethanol, formic acid and C8 hydrocarbons. The research investigation (8) performed by the USBM indicated that "smoldering combustibles generate a very low level of CO compared to the level of smoke produced". The cited publication (8), states that, "During smoldering combustion, typical mine combustibles produce about 2.5 times more smoke than CO. As fires develop to their flaming stages, the trend reverses and about eight times as much CO is produced as smoke." The reader is referred to several significant sources of additional information pertaining to emission products that can be found in references (8), (9), and (10). ANALYSIS OF FIRE HAZARDS U.S.A. AND ENGLAND Nearly 15 percent of all underground coal mine fires in the United States involved ignition of conveyor belts (7). In many cases, the fires propagated through thousands of feet of belt entry and created losses in the millions of dollars. Some of these fires consisted of rubber belts. Some involved polyvinyl chloride and neoprene belts that were classified "fire resistant". Typically, a belt fire begins after the conveyor is stopped. The fire is initiated by burning coal dust and grease accumulation around defective rollers or belt drives that have become heated by friction (7). An analysis of 113 conveyor fires (11) showed that 41 originated at the driving pulleys, 32 at the defective rollers, and 40 elsewhere on the conveyor system. The severity of the fire, which can spread along a conveyor road, has been emphasized by the disaster at Creswell Colliery, Derbyshire, on September 26, 1950, when 80 men were overcome and killed by toxic fumes from the fire (12). The fire started from smoldering caused by friction, and developed into a flaming combustion, propagating along the roadway containing the rubber belt at an estimated speed of 40.2 m/s (90 mph), and travelling a total of 650 m (2100 ft) THE INFLAMMATION OF CONVEYOR BELTS THE MECHANISM OF IGNITION Defective operation of a conveyor belt may start a fire in several ways: - Friction of the belt on the drive pulley. - Jamming of a guide roller, and others.

Jan 1, 1991

By Douglas E. Pollock

Recent NIOSH published information has shown an increase of rapidly progressive coal workers? pneumoconiosis (CWP) in the southern Appalachian coal region (SAR) of the U.S., despite the fact that compliance data indicates that most coal miners have been exposed to coal mine dust concentrations below the statutory limit of 2 mg/m³. While the exact cause of these elevated CWP levels in the SAR has not been established, several factors may be contributing to the increase in occupational lung disease among coal miners. The mining of high rank coal is known to lead to higher CWP rates, and this type of coal is mined in a portion of this region. Also, a high percentage of the mines in the region are on reduced dust standards because of the high silica content of the airborne dust resulting in miners possibly being exposed to excessive amounts of respirable silica dust. Exposure to excessive amounts of respirable silica dust can lead to silicosis, a disabling and potentially fatal lung disease. NIOSH?s Respiratory Hazards Control Branch has been investigating the possible causes that would account for the observed higher trends in disease progression through literature review, data analysis and in-mine surveying. The investigation to date has revealed that underground mines are faced with cutting large amounts of rock in order to maintain haulage clearances. Cutting rock not only increases the potential for silica exposure, it increases the requirement for machine maintenance, which was a concern observed during dust surveys conducted by NIOSH. Over half of the mines operating in the SAR are on reduced standards due to high silica content. Adequate face ventilation of the continuous miner and roof bolter and limited down-wind operations from the miner are also issues of concern and items that require the constant attention of miners operating in these conditions.

Jan 2, 2010

By D. E. Pollock

Recent NIOSH published information has shown an increase of rapidly progressive coal workers? pneumoconiosis (CWP) in the southern Appalachian coal region (SAR) of the U.S., despite the fact that compliance data indicates that most coal miners have been exposed to coal mine dust concentrations below the statutory limit of 2.0 mg/m³. While the exact cause of these elevated CWP levels in the SAR has not been established, several factors may be contributing to the increase in occupational lung disease among coal miners. The mining of high rank coal is known to lead to higher CWP rates, and this type of coal is mined in a portion of this region. Also, a high percentage of the mines in the region are on reduced dust standards because of the high silica content of the airborne dust resulting in miners possibly being exposed to excessive amounts of respirable silica dust. Exposure to excessive amounts of respirable silica dust can lead to silicosis, a disabling and potentially fatal lung disease. NIOSH's Respiratory Hazards Control Branch has been investigating the possible causes that would account for the observed higher trends in disease progression through literature review, data analysis, and in-mine surveying. The investigation to date has revealed that underground mines are faced with cutting large amounts of rock in order to maintain haulage clearances. Cutting rock not only increases the potential for silica exposure, it increases the requirement for machine maintenance which was a concern observed during dust surveys conducted by NIOSH. Over half of the mines operating in the SAR are on reduced standards due to high silica content. Adequate face ventilation of the continuous miner and roof bolter and limited down-wind operations from the miner are also issues of concern and items which require the constant attention of miners operating in these conditions. Disclaimer: Mention of any company or product does not constitute endorsement by the National Institute for Occupational Safety and Health.

Jan 1, 2009

By R. B. Krog

The use of belt air as an intake source at longwall operations has greatly changed over the past decades. The practical considerations for the use of belt air are controlled by a variety of factors including airflow quantity and velocity, coal methane content, methane desorption rates, coal mining rate, belt length, stopping leakage, and the number of gateroad entries. At longwall operations, the advantages and disadvantages of belt air are different for gateroad development and longwall panel extraction. During gateroad development, the use of belt air to ventilate the working section will reduce the leakage from the intake to the belt compared to the belt air being ventilated outby the working sections because of lower pressure differentials. A greater quantity of airflow will reach the last open crosscut with belt on intake than outby, given the same amount of pressure and airflow available at the mouth of the section. This paper will investigate the current ventilation practices regarding the use of belt air during gateroad development and longwall panel extraction. Operating considerations regarding air quantities and pressures to deliver the required airflow will be investigated using ventilation network modeling.

Jan 1, 2009

By Yunsheng Yao, P. Golledge, A. D. S. Gillies

In order to investigate the explosibility of sulphide mineral dusts, sulphide ore samples were collected from five underground metalliferous mines in Australia. The mineralogical and chemical composition of the dust samples was analysed by X-Ray Powder Diffraction and Atomic Absorption techniques. Simulated post detonation fumes were produced and used in dust explosibility tests to examine the influence of the fumes on sulphide dust ex- plosions. These tests were conducted in a 20 Litre Siwek Explosion Chamber with measurement and control system that is regarded as a standard testing system worldwide for dust explosion studies. The dust mineralogical composition and dust explosibility tests indicated that the content of sulphur can not accurately predict the explosibity of the sulphide dust. The percentage content of pyrite in the sulphide dust can be a relatively reliable diagnostic criterion in evaluating the risk of sulphide dust explosions in the mining of a massive sulphide orebody. The hybrid explosion tests demonstrated that the post detonation fumes from ANFO not only decrease the lower explosion limit of the sulphide dusts, but also increase the severity of the dust explosions. The explosion pressure reaches its peak value when the fumes content in the explosion chamber is about 20 per cent by volume

Jan 1, 1997

By N. S. Tanious

This paper summarizes results from an investigation into possibly the largest coal pillar failure in the USA. The newly opened coal mine worked an 3.35 m (11 ft) seam under overburden depth that ranged from 91 to 671m (300 to 2200 ft) . The mine main entries, and the enclosed pillars, experienced a massive slow squeeze. The squeeze could not be controlled and the mains were lost. A new set of mains were driven. Entry convergence (closure) measurements were carried out behind the advancing face to monitor stability. Pillar stresses were also measured under four different depths of overburden: 229.433, 472.579 m (750,1420,1550, and 1900 ft). The strength of pillars in the new mains was calculated from the loads that triggered the failure in the old mains, using three pillar strength formulas. The stress measurements showed that the new pillars supported more load than their predicted strength, indicating that current strength formulas are inadequate under deep conditions.

Jan 1, 1992

By N. S. Tanious

This paper summarizes the results of an investigation into possibly the largest coal pillar failure in the USA. The newly opened drift mine is located in Southeastern Kentucky and worked an 11 feet thick coal seam, all other mines in the District worked seams 4-5 feet thick. The initial mine development consisted of 14 main entries (Fig. 1) which were driven in two sets of 7, under increasing depth of overburden. As the left seven entries came under deeper overburden the pillar ribs began sloughing which caused many of the concrete-block ventilation stoppings to crack. The mine management stopped the advance in the left seven and continued with the right seven entries. During the spring of the following year development resumed in the left seven, rib sloughage occurred again and this time severely cracked many stoppings and many were totally disintegrated from the excessive deformation. Within few weeks the sloughage was so heavy that many of these entries behind the active face were filled with piles of sloughed coal slabs. When the face reached a depth approximately 1150 feet, the sloughage became a slow, massive squeeze. The entry convergence (closure) reduced their height from 11 to 7-8 feet and the squeeze spread back to shallower depth covering an area roughly 300 pillars.

Jan 1, 1989

By Sunny Schoone, Maximilian Getz, Felix Leaman, ELISABETH CLAUSEN

Hydraulic transport is commonly used in mining for moving particles or ore concentrates in pipes over long distances with a water stream. Control and monitoring of this process require sensor technology that can obtain relevant characteristics of the two-phase flow. This work investigates the acoustic emission (AE) technology for monitoring a hydraulic system with different sand concentrations, showing the strong relationship between friction behavior in the pipe and the measured AE signals.

Apr 1, 2023

By Serdar Aktaş, Burcu Nilgün Çetiner

According to critical statistical studies, antimony is one of the rarest elements in the world, and global resources could be exhausted by 2050. In light of these observations, its extraction will be costly due to poor-quality ore, deep mining, remote locations, and high energy consumption. In the present study, an alkaline leaching process was carried out on stibnite concentrate to evaluate the effect of reaction parameters on the percentage of antimony extraction. The leaching efficiencies of different sulfur and hydroxide sources were studied and compared to one another to create a better understanding of the reaction process. Kinetic models were investigated to identify the reaction pathway and calculate the activation energy. The activation energy of the stibnite dissolution was assessed as 19.13 kJ/mol using a two-dimensional diffusion-reaction model. The value of activation energy indicates the quantity of energy necessary for a reaction to proceed. As expected, potassium hydroxide leaching was significantly more successful than was sodium hydroxide; however, in terms of economics, the use of sodium hydroxide was found to be more cost-efficient. Interestingly, this finding indicated that caustic leaching is still the most effective method for stibnite extraction.

Jul 23, 2020

By BURCU NILGUN CETINER, Serdar Aktas

Antimony has been used extensively in industry and in everyday life since the 19th century, and antimony sulfides have been known since around 4,000 B.C. Antimony’s most significant applications are as a flame retardant in the manufacture of electronics and textiles, as a catalyst for plastic fabrication, and as paint pigment and fining agent in glassware, opacifier in ceramics and an alloying element in ammunition and battery manufacturing plants. It is also used in vehicle brakes and tires. Brake pads contain stibnite (Sb), the sulfide compound of antimony. In particular, stibnite is used in automobiles as a lubricant, vibration reducer and friction stability improver. Anthropogenic activities are the primary source of antimony in the atmosphere [1,2]. Annual global consumption of antimony has increased to more than 1.4 × 105 t, and China is the most significant producer [2].

By R. I. Pennington, J. L. Vanderbeek

Investigations have been conducted at Chino Mines Co. into the effect that SAG mill recycle material (critical size) exerts on SAG mill throughput and specific energy requirements. Tests were conducted on laboratory, pilot, and plant scales to evaluate the merits of alternative treatment options. Removing critical size material from the SAG mill circuit has been shown to improve new feed rates by 84% with a reduction in specific energy (kWh./t) of 88%. Test results obtained to date are presented.

Jan 1, 1987

By Umay Cinarli, Ahmet Turan

High-energy consumption in primary aluminum production (from bauxite ores) makes secondary aluminum production (from metallic raw materials such as scrap and dross) very critical. Aluminum dross, as a waste, arises in pyrometallurgical processes, and it is the mixture of metallic Al, Al2O3, other metal oxides, metal halides, and some other compounds like AlN. Aluminum dross has two subgroups (white and black) with respect to its metallic aluminum content. White dross is a secondary aluminum resource because of its high metallic aluminum content, whereas black dross, having low metallic aluminum content, is generally disposed in dumping areas. In the present study, it was aimed to develop a simple technique to valorize aluminum black dross in the form of alumina-based ceramic materials through pyrometallurgical (calcination) and hydrometallurgical (leaching) operations. Moreover, thermochemical simulations were conducted by using HSC Chemistry 6.12 software to simulate calcination conditions. After leaching experiments, an alumina-based ceramic containing approximately 36.8% Al2O3, 61.4% MgAl2O4 with 1.8% Na2FeO4, which might be available to use as a spinel refractory in steel smelting furnaces, was obtained in the experiment carried out in a solution containing 10 mLH2SO4 and 40 mL distilled water (3.5 M). Moreover, the sinterability of the alumina-based ceramic was investigated at the temperatures from 1350 to 1550 °C. In the sample which was sintered at 1550 °C, a density value of 3.15 g cm−3 and a hardness value of 69.58 HV were measured.

Oct 26, 2020