Search Documents

By Swati Mohanty, G. V. Rao

Sedimentary dolomitic phosphate ores are difficult to treat by flotation, and high-grade phosphate concentrates with high recoveries are difficult to obtain. The literature indicates that the reagents required for beneficiation of such ores are generally dictated by the nature of the gangue. In this paper, the optimum flotation parameters necessary for enhancing the grade and recovery of a typical low-grade dolomitic rock phosphate ore from Jhamarkotra, Rajasthan, are highlighted. The standard design-of-experiment (DOE) technique was used to obtain empirical models for both grade and recovery. The model equations were then used for optimizing the flotation parameters, including pH, percent solids, collector dosage and depressant dosage. Laboratory experiments demonstrated that a phosphate concentrate containing about 36% P205, with a recovery greater than 95%, can be obtained in a single-stage by the reverse flotation of carbonaceous minerals at the optimized conditions. Key words: Phosphate, Flotation, Dolomite

Jan 1, 2003

By A. Noble

"Froth flotation circuits are widely used throughout the mineral processing industry for the concentration of fine particles. It had been estimated that nearly 2 Gt (2.2 billion st) of ores are treated globally each year using this versatile separation process (Fuerstenau, 1999). Due to the high feed tonnage, a large economic incentive exists for flotation plant operators to optimize the performance of this critical processing circuit. Prior to the 1950s, the optimization of flotation circuits primarily involved the manual adjustment of operating variables based on visual observation and sporadic sampling (Lynch, Harbort and Nelson, 2010). During the next several decades, however, the advent of improved on-line instrumentation coupled with the rapid development of high-speed microprocessors allowed the industry to develop more advanced control systems that could quickly adjust operational parameters in response to disturbances in ore characteristics and plant flows. These early online controls typically involved feedback loops designed to stabilize cell performance through the automatic manipulation of process variables such as pulp levels, gas rates and chemical dosages. The set-points for these controllers were often set by plant operators based on one or more operator objectives, such as maximizing throughput, recovery or grade. More recently, these regulatory controllers have been interfaced with high-level data display and management systems that provide operators with the ability to better optimize flotation plant performance based on mathematical models and rule-based algorithms (Greet, 2010).While tremendous strides have been made during the past several decades, even the most modern flotation plants are still faced with the long-standing question: “What are we trying to optimize?” From an operator perspective, some common responses include “Maximize tonnage of saleable concentrate” or “Maximize metals recovery at a customer-specified market grade.” These replies may or may not reflect those of management, who often focus on economic goals such as “Maximize profits for each operational unit” or “Maximize rate of return for all corporate assets.” Unfortunately, these high-level objective statements do not always translate well into practice due to the disconnect between plant operating protocols and product value. Attempts have been made by industry to overcome this issue using various types of optimization routines such as linear programming or other optimization engines. While this approach does have some merit, these blind routines require considerable input data and interpretational expertise and provide little or no fundamental insight that can be used to drive improvements in concentrator performance."

Feb 1, 2017

By Dan Nilsson

Rock from underground mining has a size-distribution, that varies from mine to mine, depends on rock conditions and mining method and on how much explosives etc, that is used. Because at the high costs, associated with full-scale studies of the size-distribution of blasted rock in a mine, detailed information is seldom published about such size-distributions. However, some facts can be noticed. Rock from tunnelling and other types of development work has a fine fragmentation. Cut-and- fill mining is a method that normally results in blasted rock with an advantageous size distribution. Block caving on the other hand often results in large amounts of boulders, since blasting of the rock is normally not used.

Jan 1, 1985

By R. C. Gilmore, S. A. Lolon, G. E. Bogin, S. A. Saki, J. F. Brune, J. W. Grubb

"Gob ventilation boreholes (GVBs) are widely used in underground coal mines for longwall gob degasification purposes. GVBs are often drilled within 10 to 30 m above the top of the coal bed into the fractured zone, completed with 20 cm (8 in.) diameter casing and 60 m of slotted pipe at the bottom. The purpose of this completion strategy is to create a pressure sink to capture the emissions before they can enter into the underground workplace. For GVBs to work effectively, they must be drilled close enough to the working areas to capture methane from the fractured zone while the setting depth must be kept above the caved zone to minimize the amount of ventilation air that is drawn into the GVBs. Well completion parameters are important for creating safe working conditions. In this paper, computational fluid dynamics (CFD) studies will be presented to analyze the effect of different practices for GVBs completion parameters for methane extraction, formation of explosive gas zones in the gob and methane concentrations at the longwall face and tailgate. Authors have identified the optimum completion parameters for GVBs, which can maximize the benefit and minimize fire and explosion risk. INTRODUCTION Coal mines may be considered gassy based on the presence of CH4. Gas from the mined coalbed or from rider seams above or below the mined coalbed can migrate into the gob and then potentially move towards the working areas. In longwall coal mines with high methane emissions, sufficient ventilation and additional methane control measures are usually required to reduce the methane concentration in working areas to below statutory levels. Several techniques or combinations of techniques are available to control the methane hazard. These may include mine face ventilation to dilute methane, coal bed degasification, nitrogen injection into the gob to render a methane atmosphere inert and the use of gob ventilation boreholes (GVBs). Longwall face ventilation and dilution alone can only handle methane emissions up to a certain amount. When methane emissions exceed the face ventilation capacity, additional control measures are required. Drilling horizontal or vertical methane drainage holes into the coal seams as well as gob ventilation boreholes from the surface into the gob area to extract methane are common practices. GVBs are usually drilled from the surface above the longwall panel ahead of mining. When the face moves outby the GVBs and the gob begins to form, methane production starts from the boreholes. It is important to control the performance of GVBs to maintain a safe working environment in the mine. The performance of GVBs depends on multiple factors, including borehole location, length and diameter of slotted casing, setting depth of casing above the coal seam being mined, wellhead vacuum pressure, and permeability of caved-fractured zones."

Jan 1, 2016

By Wolfgang Baum

This paper discusses the use of mineralogical work during the develop ment and operation of gold heap leaching projects. It focuses on the early assessment and prediction of metallurgical performance, the identi fication of gold recovery problems and the application of mineralogy in process optimization. The results of extensive operations support work emphasize the benefits of routine plant mineralogy. Mineralogical characteristics are amongst the most important factors determining leach- ability, leach time, reagent consumption, insoluble losses, scale forma tion and equipment performance.

Jan 1, 1990

Conditional simulation provides a model of the ore body that represents variability in the data. This can be used to determine the impact of various grade control and mining strategies. A number of transfer functions are discussed that assist in optimizing grade control sampling. The cost effectiveness of various drilling and trenching techniques are discussed. Modelling of the expected performance of a mill head grade sampler is investigated. Conclusions are drawn about the likely impact of various sampling techniques on the economic performance of an operation and about applying sampling theory to grade control sampling.

Jan 1, 1999

By T. S. Bomar, C. J. Wood

Heavy media cyclones (HMCs) are efficient, high-tonnage devices suitable for upgrading run-of-mine coal in the 50 to 0.5 mm size range. Unfortunately, industrial HMC circuits are often not optimized due to problems such as incorrect operating pressures, poor feed distribution, excessive media contamination, mismatched components, and improper density control. To avoid these problems, operating guidelines have been provided in this article that are useful for optimizing the performance of HMC circuits. The validity of these guidelines has been assessed by means of density tracer tests carried out at several coal preparation plants.

Jan 1, 2002

By Kristin K. Mueller, Lucie Coudert, Thi Yen Chau Nguyen, Lan Huong Tran, Jean‑François Blais, Guy Mercier

Fluorite (calcium fluoride—CaF2), also known as fluorspar, is an industrial mineral used in metallurgy, hydrofluoric acid production, and ceramics manufacturing. Based on the results from a previous study, a low-grade fluorspar by-product (20.0% CaF2) originating from the exploitation of a rare earth carbonatite deposit can be improved to 75.4% by combining magnetic separation and acid leaching. The present research aimed to develop and optimize a column flotation process to increase the purity of this fluorspar by-product by removing residual silicate minerals and meeting the requirements for ceramic manufacturing (> 85% CaF2). The optimal flotation conditions required for maximizing the recovery and improving the grade of a fluorspar by-product were identified using a conventional approach combined with a response surface methodology (Box-Behnken design). Optimal fluorspar flotation was achieved under the following conditions: 3.6 g/kg of sodium oleate as the collector, 2 g/kg of sodium silicate as the pH modifier and depressant, a conditioning time of 35 min, a flotation time of 7 min, and a solid-to-liquid ratio (S/L) of the pulp of 5%. Under these conditions, 86.8% fluorspar recovery was achieved, and the grade increased from 76.5% in the feed (metallurgical grade) to 88.6% (ceramic grade) in the final concentrate. The silicon content decreased from 5.66% in the feed to 1.12% in the fluorspar concentrate. Using magnetic separation before the flotation improves the final content of fluorspar in the concentrate with the final grade of 94.4%.

Sep 9, 2022

By Hasan Sevim

This paper summarizes recent developments in modeling of underground coal slurry haulage networks for determination of optimum design and operating parameters. The model presented here is based on a stochastic dynamic programming formulation, applicable in any typical room-and-pillar and/or longwall mining configuration commonly practiced in the United States. The formulation and the structure of the model is general enough to handle design problems involving more than one face and mining method. Given the stochastic operating characteristics and a system layout, the model can be used to determine the equipment configuration and operating regimes that minimize the overall unit cost of coal haulage.

Jan 1, 1983

By Sah Rameshwar, T. Umadevi, K. S. SRIDHARA

In the magnetite iron ore pelletization process, oxidation of magnetite followed by sintering of the oxidized magnetite (hematite) is desirable. Optimum preheating time & temperature and roasting time & temperature is required to get the desired properties of the pellets with magnetite, hematite, and hematite–magnetite blend. In order to utilize the magnetite resources in a current induration furnace, which is designed for hematite resources, detailed pelletization studies have been carried out to optimize the firing cycle for magnetite concentrate as well as magnetite with hematite concentrate. Under optimum conditions, such as preheating temperature 1000–1150 °C, preheating time 10 min, roasting temperature 1250 °C and roasting time 7.5 min, the cold compression strength (CCS) of magnetite roasted pellets was 325 kg/p, and this was due to recrystallization of secondary hematite particles, and development of the strong slag bond between primary and secondary hematite particles. The strength of hematite concentrate pellets was 260 kg/p. From laboratory studies, it was found that without disturbing the induration furnace firing cycle, which is designed for hematite ore ~5%, magnetite concentrate can be used along with hematite concentrate in pellet blend and the strength of the pellets was 270 kg/p. As the magnetite concentrate increases in the blend beyond 5%, the preheating zone residence time should be increased or a supply of extra oxygen is required. Laboratory as well as plant investigation has shown that the addition of magnetite to the hematite mix blend improved the strength of the pellets compared to hematite pellet alone.

Oct 26, 2020

By R. Larry Grayson

A menu-driven, linear-programming- based, user friendly computer program was developed to assist mine managers in determining optimal longwall panel dimensions for a given set of operating conditions. A sensitivity analysis must be performed by varying key mining and configurational parameters over an expected, practical range during the optimization process. Results from analysis of a base case mine indicated that no single combination of longwall panel length and face width is optimal for all operating situations. Each mine manager must therefore look closely at his operating situation and determine the proper dimensions to minimize total mining cost.

Jan 1, 1989

Magnetic separators are commonly used as an effective and low-cost method to concentrate paramagnetic or ferromagnetic minerals. These versatile separators are often used in multistage circuit configurations to further improve concentrate recovery and/or grade. Although these circuits are generally very efficient, field studies suggest that the layout of multistage circuits can be less than ideal for many industrial operations. To illustrate this shortcoming, a theoretical analysis has been conducted to compare different circuit configurations for magnetic separators. The resulting knowledge base has been used to establish generic engineering guidelines for the layout of multistage circuits. The potential improvements in separation efficiency that may be realized through the application of these guidelines have been demonstrated using a simple case study.

Jan 1, 2004

By K. G. Correia

The replacement of the dry mining method at Guajú Mine by the dredging method was a means of ensuring its feasibility by maintaining the production levels. Dry mining increased the cost of the deposit with the distance and presented a limited mined volume, while the decreasing grade of the deposit led to a production drop. With the new methodology, there was a considerable reduction in unit cost of the mine and an increase in the production level of a deposit with low heavy minerals content.

Jan 1, 2005

By H. M. Wells

It is with great pleasure that I read Mr. Howard M. Wells article in the Decmenber 1978 issue of MINING ENGINNERING entitled: Optimization of Mining Engineering Design in Mineral Valuation."

Dec 1, 1978

By M. Menéndez

Enhanced gravity separation appears to be one of the most promising methods for processing all types of <200-µm coal feeds and tailings. Systems based on this technology are reviewed, and the results of investigations based on C900 Multi-Gravity Separator tests conducted to assess the treatment of <200-µm, extremely difficult-to-wash coal settling pond tailings are presented. Multi-Gravity Separator processing tests of ultra-fine tailings with a high clay particle size content (22.6% <10 µm and 60.1% <40 µm) and a 69.56% ash content show that this material can be effectively treated after desliming (<10 µm) of clay-size particles to produce a coal with a 20.6% ash at a separator combustible material recovery of 69.3%. Desliming is shown to be critical in reducing coal ash content and combustible material recovery. Similar improvements are anticipated in the recovery and separation pro-cesses for other enhanced gravity separation systems from the desliming of feeds. Although not a conventional form of treating Multi-Gravity Separator data, the existence of well-defined polynomial relationships based on the product of drum shake amplitude and shake frequency relative to product coal recovery, product ash content and yields at varying wash water flows is demonstrated. Low-amplitude and intermediate- to high-frequency bed agitation are shown to produce optimum ash reduction results.

Jan 1, 2007

By T. J. McKeon

Gravity separators such as spirals are commonly used in multistage cleaning and scavenging circuits to improve the quality and recovery of concentrates produced in the industrial minerals industry. Unfortunately, field surveys suggest that many industrial operations are poorly configured in terms of equipment layout. This shortcoming can often be attributed to a failure by engineers to make use of fundamental process engineering tools for circuit design. One of the most important of these is linear circuit analysis. This powerful tool makes it possible to mathematically compare the relative efficiency of circuit configurations in advance of experimental testing. This article provides a basic review of the linear circuit analysis concept and discusses some of the key insights it provides for the layout of multistage circuits. An industrial case study is provided to show the tremendous impact that this process engineering tool can have on the design of multistage spiral circuits in a heavy mineral wet plant.

Feb 1, 2012

By James E. McTurk, Sheldon B. Bland, Roger E. Melley

During the first fifteen years of operation at the Syncrude facility in northern Alberta, numerous improvements have been made in the field of ore conveying. The unique nature of the material conveyed coupled with the wide range of environmental conditions encountered results in a number of unparalleled challenges. Most of the improvements have been brought about with the use of detailed field evaluation. This paper outlines some of the programs which have been run to optimise belt and system construction, and conveyor performance and utilization.

Jan 1, 1993

By I. Casasbuenas, K. A. Nguyen, E. I. Ngoma, H. Kim, D. Borja, J. H. Park, R. A. Silva, S. Choi

"This study aimed to determine the optimum operating parameters of a continuous bioleaching system to leach arsenic (As) from mine tailings using a mixed mesophilic bacterial culture. The microbial consortium, previously adapted for effective growth at high pulp density and metal concentrations, was mainly composed of Leptospirillum ferriphilum, and Acidithiobacillus caldus. The mine tailings, collected from the Janggun mine (South Korea) contained 11% (w/w) of As. The tests were performed in a laboratory-scale unit composed of three reactors connected in series following a cascade configuration. Agitation speed, air supply, solid concentration, residence time and temperature were systematically optimized by assessing the leaching activity. Several parameters were monitored on a daily basis, including the As released into solution, iron oxidation rates, pH, cell concentration, dissolved oxygen and redox potential. Overall, improvement of oxygen transfer, by optimizing the agitation speed and air supply, presented the most tangible impact on the leaching performance. The highest As leaching efficiency observed in this study was 82%, which supports the feasibility of the process. INTRODUCTION Worldwide, around of 65 billion tons of mine tailings are produced every year (Jones & Boger, 2012). These materials comprise the waste minerals produced after ore beneficiation. Mine tailings usually contain heavy metals (e.g., Cobalt (Co), Lead (Pb), Zinc (Zn) and Arsenic (As) (Falagán, Grail, & Johnson, 2016; Nguyen, Lee, Park, & Lee, 2014). The exposure of these materials to the environment can produce serious health damage and environmental degradation (Martin, Dowling, Pearce, Sillitoe, & Florentine, 2014). Mine tailings management represents a major issue in South Korea. There are more than 1,000 abandoned mines containing stockpiled mine tailings within the territory (Choi, Park, Hong, Park, & Kim, 2013; Kim, Kim, Ahn, Ko, & Lee, 2005; Lee, Lee, & Kim, 1998). These tailings comprise high concentration of arsenic. Therefore, the Korean Government has directed its efforts to developing eco-friendly technologies, for the arsenic detoxification of mine tailings Continuous bioleaching is explored as a remediation technology (Borja et al., 2016). The present study aimed to develop a mixed mesophilic bacterial culture for optimal growth at high metal and solid concentration; and optimize the operating conditions of a continuous bioleaching unit. This investigation forms part of a larger study aimed to develop a bioleaching technique to treat Janggun mine tailings (Borja et al., 2017; Ngoma et al., 2017)."

Jan 1, 2018

By G. T. Lineberry

Horsepower requirement is recognized as a most important equipment characteristic. Other critical equipment characteristics will be isolated and analyzed by traditional operations research techniques, using off-highway trucks as an archetype. A computer search technique has been developed, employing various production and cost analyses. With this model, the optimum combination of horsepower, capacity, and velocity can be found, minimizing handling cost per ton. An example of the program&apos;s use and interpretation of its results will conclude the paper.

Jan 1, 1984

By Barry J. Hansen, Ruston A. Ford

Production of mine backfill from the tailings produced in a proposed Crandon concentrator is described. A process has been developed capable of producing suitable fill for the mining method selected for the Crandon orebody. It maximizes the placement of pyrite underground as fill and segregates tailings into pyrite and nonsulfide fractions. To determine the suitability and engineering characteristics of the backfill product for use underground, laboratory and physical stope simulation model testing was conducted. The results of the testing and the application of those results to the design of the backfill system ultimately affecting mine geometry and subsequent mine production will be presented.

Jan 1, 1981