Search Documents

By Fred C. Bond

Any improvement in the accuracy of commercial comminution calculations under the Third Theory must be accomplished either by increased precision in energy input measurements, or by a better evaluation of the total new crack length produced, as indicated by the feed and product size distributions. Since at the present time feed and product sizes are approximated solely by the microns 80% passes, the most promising opportunity for increased accuracy lies in consideration of their plotted size distribution characteristics. This paper shows how more accuracy can be obtained over an increased range of feed and product sizes from size distribution studies.

Jan 1, 1962

By Donald G. Oss

The need for instrumentation and automatic control of the various parameters in the heavy media process of iron ore beneficiation has been apparent for some time. Continued demands for higher grade, competitive products from the Mesabi Range have made it necessary to increase the efficiency of the process in every possible way. A brief review of a typical heavy media flow scheme, as illustrated in. Figure l, might be in order for those not intimately associated with this process of iron ore beneficiation.

Jan 1, 1962

By Stephen Utter

This report summarizes the results of preliminary investigations concerning the influence of block caving mining upon adjacent mine openings and discusses possible methods for reducing critical rock pressures and damage to these openings. These investigations are one part of a general study of the rock mechanics of block caving by the Denver Mining Research Center of the Federal Bureau of Mines. The purpose of this part of the study Is to obtain an estimate of the stress concentrations around mine openings adjacent to block caving stopes for use in developing better designed openings and improving mining methods. When mine openings such as slusher drifts, grizzly drifts, and haulage drifts are damaged by rock pressures induced by block caving mining, the mining cost increases, mine production decreases, and ore recovery may be consider- ably lessened. Methods of mining that result in lower rock pressures and methods of design that enable mine openings to withstand these pressures are desirable. The development of these methods, in turn, requires a fuller understanding of the following: The stres concentrations around the mine openings and the changes in stress induced by adjacent mining; the physical properties, such as the compressive strength and modulus of elasticity of the rock surrounding the openings; and the support supplied by the concrete lining, timber sets, or other types of supports used in the openings.

Jan 1, 1962

By T. L. Myron

To determine the effect of flux crystal size on the production rate and strength of sinter, batch sintering tests were conducted on samples of both dolomite and limestone of various crystal sizes. In addition, calcination tests .were performed on the dolomite and Limestone to determine the effect of crystal size on calcination rate at various temperatures normally attained in sinter beds. The results indicate that flux crystal size does not affect sinter production rate or sinter strength.

Jan 1, 1962

By E. W. Davis

This paper deals with the role of the Maintenance Department in a milling operation; specifically, the Mines Development, Inc., processing plant at Edgement, South Dakota. The goal of very maintenance department is the smooth and uninterrupted operation of the plant it serves, To achieve this goal, maintenance men adapt various features and procedures into a program designed to fit the characteristics of their particular plant operation. A few of the basic elements of a sound maintenance program are: 1, A periodic preventive maintenance schedule. 2, A systematic inspection and lubrication procedure. 3. A training program for maintenance personnel. 4 A good equipment-history file system, 5. A carefully planned spare parts inventory.

Jan 1, 1962

By E. J. Ostrowski

The history of ironmaking dates back to 4000 BC when an open forge was used to produce a sponge iron from a heap of ore and charcoal. Even at this early date, man recognized the need for a fuel and a reducing agent. As time passed, man developed new methods of producing iron; however, these developments were centered on the mechanical aspects, and as a result, a furnace evolved which is now known as a blast furnace. During this period of evolution,' man struggled with the only fuel he knew - charcoal. Some 5600 years passed before any attempt was made to use coal as a fuel for the blast furnace. The use of coal had its beginning in 1619 when Dud Dudley of England first attempted its use in the blast furnace; as a-fuel and as a reducing agent. Coal charged to the top of the blast furnace was not satisfactory. The volatile matter of the coal choked the flues, and also the poor, strength qualities would not support the weight of the ore. Breaking up of the coal compacted the stock column to an impervious mass. One hundred and sixteen. years later in 1735, Abraham Darby of England introduced coke as the fuel and reducing agent in the blast furnace. The acceptance of coke as a fuel for the blast furnace was not spontaneous. As late as 1870, one-half of the pig iron product of the United States was made with anthracite coal, 30 per cent with raw bituminous coal and coke, and 20 per cent with charcoal. However, by 1910, 96.2 per cent of the blast furnace product was made with coke, 2.4 per cent with anthracite and coke admixture, and 1.4 per cent with charcoal. Coke became the standard fuel in the blast furnace. As the art of ironmaking progressed, more pig iron was produced and more coke was consumed. Coke oven capacity was progressively increased. In 1910, there existed approximately 4,000 coke ovens; in 1960 there was approximately 15,000 ovens. This increase in coke oven capacity was necessary to feed the mammoth appetite of modern blast furnaces.

Jan 1, 1962

By M. J. Langley

Zinc ores were first discovered in Tennessee in 1856 at Jefferson City where a deposit of oxidized ore became known as the Mossy Creek Mine. From that time until 1913 small scale attempts at prospecting and mining were made in various parts of the district. The actual systematic development of the zinc deposits dates from 1913 when the American Zinc Company started operations at Mascot. Six mines are in operation by three companies and a seventh mine is being developed by a fourth company. The total daily production from the field is 11,000 tons of crude ore, which grades from 3 to 6 per cent zinc. Most of the ore bodies are large and ramiform, resembling asyrmetrical networks in which the ore shoots form channel like branches with areas of non-comercia1 rock, called blank islands. Most of the orebodies are adapted to large scale mechanization.

Jan 1, 1962

By H. E. Rowen

I hope my title is not confusing; even more so that I am not. Actually pelletizing and sintering, meaning both the formation of pellets and the hardening of them, are closely related to each other and to phenomena of nature. Figure. 1 This many-celled porous structure, frozen as it was at the fusion temperature and was being frothed by fast-moving gases, may be considered a typical piece of sinter. The same structures have been found in natural ores.

Jan 1, 1962

By William F. Tanner

A river delivers a given load of sand, and hence of heavy minerals, into the sea into which it empties. This load is fixed by drainage basin characteristics and processes. Wave energy available for redistributing that load is fixed in an entirely different way. An equilibrium diagram of these two parameters (load versus energy) permits a tentative prediction of what will happen to the heavy minerals. The Chattahoochee River delivers a load which, over the past few thousand years, appears to have been greater than the available coastal energy could handle. As a result, much of the sand has been accumulated in various delta-margin features: barrier islands, beach ridges, and large furrowed off-shore shoals. The bulk of the trapped sand is found today in the shoals, which are attractive deposits for possible exploitation. If coastal energy levels are high enough to move the total load delivered by the river, accumulations of sand (and hence of heavy minerals) should be sought in the down-drift direction. Energy levels are rarely constant over any great length of coast. Decreases in energy may be due to widening of the shelf, convexity of, the shore, restrictions on the fetch, wave decay, or other causes. Such decreases result In deposition. Hydrodynamic mapping of coastal areas, as outlined here, should prove useful in the location of additional reserves. Part of this type of work can be done on maps, charts, and air photos.

Jan 1, 1962

By Gerd L. Klinkenborg

Throughout the history of the development of mechanical conveyor systems, it has always been an established condition that loads are received at one end of a single-belt conveyor and discharged at the other end, in a point-to-point, manner. In systems designed for the continuous transport of granular materials, vertical or horizontal changes in; direction have always necessitated two or mope single-belt conveyor units, with a corresponding number of motors, assemblies and attendant mechanical and human or electronic controls. Besides these high-cost factors, every change in the system's direction also calls for a transfer point that involves a drop-back of the material from one level to another with some loss of the material and, in many cases, unwanted additional granulation. Where changes in the location of the discharge point are wanted, the conventional single-belt conveyor must either be replaced by a shorter or longer unit or additional units purchased and installed, or existing units rearranged. This can take days or weeks, and involve special expenditures as well as loss of valuable production time.

Jan 1, 1962

By J. A. Harrison

Most coal being used in the United States has been subjected to one or' more processes of coal preparation. The physical and chemical characteristics of a coal have a marked influence on the ultimate uses that coal may have. The selection of the proper preparation processes may similarly be important in producing the best practical coal product for any particular use. The physical composition and distribution of physical constituents in the coal will partially determine the efficiency of the preparation process chosen and conversely distribution and concentration of coal macerals will, to a degree, be controlled by the preparation process. A number of preparation processes have been evaluated to determine this interrelation. If a coal having' certain specifications is desired, these evaluations trill assist in providing information needed for the production of this coal.

Jan 1, 1962

By E. A. Brecke

The Cave-In-Rock Flourspar District is located in the northeast part of Hardin County, Illinois and is the most northeasterly occurrence of flour spar of the Illinois-Kentucky Flour spar Area. The occurrence of these deposits is confined to an area about one and one-half miles wide and five miles long parallel to the Peters Creek Fault (Fig. 1) The delineation of several features that may be described as breccia pipes has permitted the definition of the point of ascent of solutions to the host horizon and the lateral spread from these points.

Jan 1, 1962

By Ralph C. Flow

In Cleveland County, North Carolina, one and one-half miles south of Kings Mountain, Foote Mineral Company operates an open pit for the production of spodumene, feldspar, mica, and commercial stone. Spodumene concentrate is sent to Footers Sunbright, Virginia plant and to other customers. Exton, Pennsylvania and New Johnsonville, Tennessee plants produce lithium compounds sold to the oil industry for multipurpose lithium-base greases, to the metal industry as welding flux, to the air conditioning market, and to the glass industry. Ceramic grade spodumene, feldspar, and mica concentrates go to other processing companies from the Kings Mountain plant. Waste amphibolite is delivered to a neighboring quarry operation.

Jan 1, 1962

By George C. Carter

It was just a little over three years ago that the "Go" button was pushed to start operations on the blending piles at Oro Grande. As is usual with any new installation, there were problems that had to be solved. This paper will concern itself with those problems directly related to quality control. To obtain a consistent outgoing quality level at the most economical level for a finished product requires two main points: 1. Measurement of variations in the process, 2. A method of making a predictable change to adjust for variations. The manufacture of cement requires a relatively high degree of accuracy if a consistent outgoing quality level is to be maintained. The blending piles were our solution to this problem.

Jan 1, 1962

By R. S. Olson

The operation of a series wash thickener-two stage filtration circuit determines the soluble loss in many hydrometallurgical operations A study of this circuit yielded expressions which permit calculation of soluble loss for almost any condition of operation. The soluble loss over a range of the circuit variables is presented to illustrate and evaluate circuit performance, The interrelation of factors affecting filter performance and some of the wash circuit, variables are quantatively described. Filter wash, which is governed by wash zone size, filter pulp level and filter feed pulp density, has the greatest affect on soluble loss. Excepting clothing blinding and flocculation the factors which decrease filter capacity also decrease soluble loss. Repulping with water, under some circumstances, can bean important means of soluble loss reduction. Water for primary filter wash, leach pulp density repulp density and wash thickener underflow density have little effect on soluble loss. The dilution of both o the filter pulps with wash solutions is suggested as a means of reducing soluble loss, and at the same, time, controlling the performance of the filters. Blowback and filter cloth blinding seriously increase soluble loss.

Jan 1, 1962

By Julian Glasser

Starting with rutile, containing more than 55% TiO2 and of the proper particle size, the commercial production of titanium tetrachloride via fluidized bed chlorination is relatively very simple and economical. As compared to shaft chlorination, it operates at a much higher capacity for given sizing of equipment, and appears more foolproof, requiring less attention. Operating data were obtained on a 53" diameter fluidized bed chlorinator using Australian rutile and petroleum coke of controlled particle size. Production rates varied from 20 to 50 tons of crude TIC14 per day for a campaign extending over one month. Close to theoretical yields and efficiencies were obtained from the viewpoint of chlorine and/or rutile consumption. Details of important equipment design, critical operating conditions and pertinent results are described.

Jan 1, 1962

By Roland F. Beers

At East Union, Knox County, Maine, near the shore of Crawford Pond, an outcrop of basic rock has been known for more than a century. The occurrence has been regarded as an unusual type of peridotite-pyroxenite, containing disseminated and massive pyrrhotite with nickel, copper and cobalt in recoverable amounts. From the outcrop, the sulfide body had been mapped more or less continuously for a distance of two miles through geophysical methods of several kinds. This paper describes the methods in sufficient detail to evaluate their significance. A core drilling program has con- firmed the location of the conductor and offers a positive means of correlating the geophysical measurements with the physical properties of the ore body. The history of the exploration offers a unique opportunity to evaluate the method of multiple geophysical methods.

Jan 1, 1962

By D. W. Alberter

I consider it a great pleasure and distinction to be invited to appear before your organization to discuss our experiences with a comparatively new system of what is known as a "Full Dimension" extensible conveyor system. One of these systems has been operating in our Diamond Smokeless Mine, Boltz, Pennsylvania, since 1959 servicing a continuous mining machines For those of you who are not familiar with this method of transportation, I would like to offer an explanation.

Jan 1, 1962

By Dan Urich

This paper covers the construction and operation of the Grate-Kiln system at the Humboldt Mine. The mine concentrator and pellet plant are located approximately 14 miles West of Ishpeming, Michigan, on the Marquette iron Range. Production of pellets began in mid-July, 1960.

Jan 1, 1962

By Stephen Krickovic

"Bleeding", as used in mine ventilation language, has a number of meanings among mining men and is regarded with different degrees of importance. This lack of uniformity stems from a number of specific situations. A method that is adequate in a mildly gaseous mine may fall short in a very gaseous mine. Projected bleeders could be dependable under a certain type of roof, and totally unsatisfactory under a different type. Similarly a plan of bleeders can be rendered useless due to undulations of seam and water in one mine and function well in another. Finally, what is effective in a mining system with partial recovery will not suffice with full recovery. You may wonder, then, if there is a common denominator for the essential function of "bleeding". In my opinion, there is, and it can be defined as controlled movement of air across an active pillar line toward the back and outby ends of the adjacent gob area into the headings provided for the purpose. The objective is to maintain as methane-free as practicable a belt adjacent to the working places, so that, if face ventilation is interrupted temporarily, the gas will not accumulate in dangerous volumes at the working faces before ventilation is restored. It's possible for these temporary interruptions to be unnoticed in time or at all. In such cases, ineffective bleeding could cause a disaster. This has happened. To control, there must be power. That is to say, there must be adequate air, pressure differential between the front and back ends of a pillar line to facilitate proper regulation for diverting of air to the various portions of the gob and as far away from the active section as is practicable. As an indication of the importance of pressure, it is noteworthy that one may provide and maintain in a reasonably open condition a heading or two for a bleeder system and fail to obtain effective bleeding .because air pressure differential is inadequate. On the other hand, you are all familiar with the fact that pillar lines in some seams can be ventilated adequately by air flow straight across the gob when the section is near a main return shaft and thus obtains a heavy pressure differential.

Jan 1, 1962