Search Documents

By J. L. Kohler

Control circuit failures contribute significantly to continuous miner downtime. The time required to put the machine back into production is a function of the time required to diagnose the problem, obtain parts, and make the repair; of these, the diagnostic time is often the largest. A microprocessor-based system with the ability to diagnose all of the common control circuit failures was designed, installed on a continuous miner, and tested. This paper summarizes the development of the diagnostic system, and provides examples of the system's diagnostic capabilities. Implementation issues and the hardware used for the prototype are briefly described. Finally, comments on the system's performance are presented.

Jan 1, 1993

By M. K. Gangal, E. D. Dainty

The CANMET diesel-related work, carried out in cooperation with the Canadian mining industry, resulted in the identification of several useful R/D studies. One such study was the development of a dash-mounted alarm signal system to indicate overexposure of production LHD diesel vehicle operators to toxic contaminants in a mine environment. The resulting instrument has been called the [CO2 Exposure Meter]. This meter is particularly applicable to LHD machines because previous investigations have indicated that operators of LHDs and some haulage truck drivers are exposed to up to 200% of the contaminant concentrations measured in the general mine return air. This paper describes the development of the system which continuously monitors and displays the operator's exposure to diesel pollutants, and indicates an overexposure by an alarm light. The overexposure limits are preset by mine personnel based on carbon dioxide (CO2) measurements, which in turn are related to simultaneous spot respirable combustible dust (RCD) measurements (or to Air Quality Indices - AQI, if available). The CO2 settings are, in general, related to the engine/exhaust treatment selections, vehicle duty cycle and local ventilation rates and efficiency. The system continuously displays one of three lights: green for underexposure, yellow for caution, and red for overexposure. Overexposure can occur for several reasons, such as: reduced ventilation, malfunction of the diesel vehicle, and excessive airborne contaminants. The paper confirms satisfactory operation of the system in a laboratory-simulated mine environment, as well as in field trials.

Jan 1, 1993

By J. K. Phiri

Copper mining is the main activity in Zambia and is confined to the large scale operations, mainly on the Copperbelt. The Copperbelt covers an area of size l00km by 50 km with a total of 10 underground and 5 open-pit mines operated by Zambia Consolidated Copper Mines (ZCCM) Limited. Most of the operations in these mines involves drilling and blasting. The loading of broken materials is by both manual and mechanical operations. Among the many risk factors associated with mining on the Copperbelt, is the occurrence of Pneumoconiosis which in the recent past has become quite prevalent and thus an important occupational health hazard for the industry. This study was carried out with the aim of establishing trends of pneumoconiosis incidence through the annual data collected by Pneumoconiosis Medical and Research Bureau of the Ministry of Health in Zambia, so that a basis could be formed for future research work. The study covers over 1,000 certified cases of Pneumoconiosis between 1960 and 1990

Jan 1, 1993

By P. R. Taylor

The ability to process complex precious metal sulfide concentrates containing antimony and arsenic, in an economic and environmentally safe manner, is an important problem facing the mining industry in the united states. Preliminary experiments have been performed to evaluate the possibility of treating a complex sulfide concentrate to recover antimony and precious metals while fixing the arsenic and sulfur as calcium arsenate and calcium sulfate. The process involves the oxidation of the antimony and arsenic minerals in the presence of soda ash (to collect the sulfur dioxide and to keep the antimony and arsenic from forming volatile compounds), the selective leaching of the arsenic from the roast calcine with a heated caustic solution, the precipitation of the arsenic and sulfate with calcium hydroxide and/or calcium chloride, the reduction of the residual antimony (collecting the precious metals), fuming of the metal to form a marketable antimony oxide, and crucible reduction of the residue to obtain a gold and silver dore. Experiments have been performed to evaluate the first stage of this process. Batch experiments were performed using synthetic concentrates of stibnite and arsenopyrite. Variables that were studied included: mixture weight fractions, temperature, gas flow rate, oxygen partial pressure and time. All of the off gas dust and sulfur containing gases were collected and analyzed. The roast solid residue was subjected to arsenic leach tests and the leach solutions were subjected to arsenic and sulfate precipitation tests.

Jan 1, 1993

Mineral processing plant operators are faced with the necessity to choose between many different possibilities for plant improvement. Only a few such possibilities, however, can be tested on the industrial site. Steady-state simulators make it possible to assess the effects of several different flowsheet modifications in a few days, thus helping the process engineer to make his choice implement the solution that seems the most appropriate and check it. The example described here is the crushing and grinding circuit of the Shila Gold Mine, jointly owned by CEDIMIN SA and BUENAVENTURA SA, in Peru. Several possible modifications for the purpose of increasing capacity have been simulated and the results assessed in terms of technical quality, investment costs and energy consumption. The best solution indicated by the USIM PAC simulator was implemented and gave a 20% increase in capacity with a pay-back time of two months.

Jan 1, 1993

By Ing Newton Amegbey, Joseph Afari Idun

Ashanti Goldfields Corporation (Gh) Ltd., the leading gold mining operation in Ghana is embarking on a major rehabilitation and expansion programme to increase gold production. A new southern ventilation district was targeted for this programme, and the ventilation system was to be reviewed in order to cope with increased production. The southern ventilation district was previously ventilated by booster fans. This arrangement was however, inadequate to solve the problem of the need to reduce smoke clearance time of the production areas, and to generally improve the underground ventilation conditions. Fan maintenance costs increased with the number of fans installed in the booster fan arrangement, and the fact that the fans were installed underground made maintenance difficult and took longer time. It became necessary to consider the installation of a new main fan on the surface. This paper gives an overview of the ventilation systems of the southern ventilation district of the mine before and after the new main fan was installed. The field tests carried out on the fan to ensure that it complied with supplier's specifications are described, and the new system analysed to see it's effectiveness.

Jan 1, 1993

In this paper, the logic and the capabilities of a long term production planning method for open pit mining are presented. The method is the first attempt in obtaining simultaneous solutions to the four interrelated parameters of open pit mining; 1) the mine life, 2) the specific blocks to be mined each year, 3) the amount of ore and waste to be mined each year, and 4) the ultimate pit limits. An efficient cutoff grade can also be obtained through a sensitivity analysis. None of the existing methods can bring such a comprehensive solution to the problem. A production plan for a real life gold deposit is given to illustrate the logic and the capabilities of the method.

Jan 1, 1993

By Andrzej M. Wala

The purpose of this paper is to describe a data-acquisition system for mine ventilation surveys that was developed by the author. The system is composed of "off-the- shelf" components integrated through a custom- designed software package to form a user- friendly data acquisition system capable of operating as an unmanned base station or as an operator-triggered roving station. To demonstrate the applicability of the developed system, the author will present data collected during an experimental ventilation survey, which was performed in one of the underground coal mines of eastern Kentucky.

Jan 1, 1993

By B. Jensen, B. K. Abraham, G. J. Tuck, A. D. S. Gillies

A dust concentration meter has been developed with Australian coal industry support for the measurement of total airborne dust concentrations capable of causing explosions in underground coal mines. The instrument, The University of Queensland Dust Meter (UQDM), measures the effective dielectric constant of a mixture of coal dust and air that is drawn between the plates of a capacitor, the capacitance of which is measured by a ratio-transformer bridge and synchronous detector system. This technique measures small changes in capacitance to approximately 1 part in 106. The unique design of the capacitor sensor permits a precise volume of coal dust and air mixture to be sampled. This arrangement overcomes difficulties inherent in optical dust measurement. The meter is portable, battery powered, incorporates data logging and has intrinsic safety approval. The operation of the meter is discussed. The system is designed to monitor dust concentrations along a coal mining face and provide concentration profiles leading to the development of suppression strategies. If data from underground tests are available, the meter's potential to contribute to establishing safe working conditions underground will be discussed. Other areas of potential application of the measurement technique are also examined.

Jan 1, 1993

By S. S. Mauney

Natural and synthetic colors are used in almost every facet of our daily lives as a means of communication and expression. Natural ochres, umbers, hematites, and magnetites were once used in their crude or semi-processed state for their pigment value in construction products and low-end coatings applications, while yielding, in recent years, to synthetically produced iron oxides for more sophisticated products. Today, through innovative mining, processing, and marketing techniques, natural iron oxide pigments are once again gaining strong inroads into products and markets requiring precise chemical and physical characteristics. With our focus on environmental consciousness and resource conservation, value added natural iron oxides provide an economical and responsible alternative to our color needs.

Jan 1, 1993

By F. W. Brackebusch

Paste is a high density mixture of water and fine solid particles with a relatively low water content (10-25%) such that the mixture has a consistency as measured by the ASTM slump cone test from slightly greater than zero up to nearly 12 inches (305mm). Particles of different size classes will not segregate or settle when the paste is not being agitated or when it is stationary in a pipeline. Cement may be a component of paste. Larger particles of aggregate can generally be added to a paste without greatly changing the pipeline transport characteristics. A paste may bleed water slightly when it is allowed to be motionless for periods of up to several hours, but the solids do not become so dense that the paste cannot be easily re-fluidized. The dividing line between the definition of a high density slurry and a paste is not sharp. It is a practical matter that must be considered when designing a pipeline transportation system. If the pipeline is very short, there is very little risk of plugging the pipeline with a high density slurry when flow is stopped for short time periods. With longer pipelines the mixture must remain stable without motion for periods as long as several hours to avoid pipeline plugging. The fine particles in a paste mixture can be composed of mine tailings or naturally-occurring clays, silts and fine sands. The mineralogy of the particles thus can have a wide variety from quartz and feldspar to clays, micas and even salts.

Jan 1, 1993

By D. G. Kotlyar

Oxidized sulfide minerals, commonly formed by weathering, increasingly are becoming important resources as primary sulfide deposits are depleted. Oxidation, in general, reduces selectivity and recovery in flotation. The objective of this research was to determine the mechanisms of oxidation and collector adsorption in sulfide systems as a step towards developing improved technologies for beneficiation of oxidized sulfides. Data from microcell flotation tests are combined with electrochemical and spectrophotometric measurements. The adsorption of ethyl xanthate (EX) on oxidized sulfides was characterized using AC impedance techniques and correlated to flotation response. The floatability of chalcocite, chalcopyrite and pyrite was dependent on the extent of oxidation. Oxidation for 1?) d at 65? C inhibited flotation of chalcocite, and chalcopyrite even after the addition of a large amount (1 x 10') M) of collector. Heavily oxidized (27 d) chalcocite remained unfloatable. However, longer oxidation of pyrite and chalcopyrite restored the floatability. Oxidation resulted in an electrically resistive, nonporous surface layer.

Jan 1, 1993

By Z. Kokesz

The following paper presents the results of geostatistical studies of the selected hard-coal deposits in Poland. Geostatistical methods were applied mainly to the characterization of variability structure of the coal seams thicknesses as well as sulphur and ash contents in the coals. Results imply that the accuracy of coal reserves estimations can be improved if kriging method is applied. Kriging allows predicting more precisely the values of such parameters as thickness and sulphuring content.

Jan 1, 1993

By Jeong-Heum Kim, Jan M. Mutmansky

A number of solution methods for solving the nonlinear equations derived from mine ventilation networks use meshes selected from the network as the basis of the solution techniques. Mathematicians working in network theory have outlined several methods for speeding up the computations through mesh selection and ordering procedures. In the mine ventilation area, a fair amount of attention has been paid by ventilation specialists to procedures for choosing the meshes so that the computational effort is eased. However, little attention has been paid to mesh ordering methods. This paper outlines research into random mesh ordering procedures plus two non-random mesh ordering procedures and compares some results using these procedures within four solution algorithms.

Jan 1, 1993

By Stanislaw Wasilewski, Zdzislaw Krzystanek

The CMC-3 new generation system for continuous methane monitoring enables on-line measurement of methane concentration within the range of 0-100% CH4 with a great autonomy of operation. In principle the system has been worked out in the asspect of hazard detection in mines endangered with rock and gas outbursts. But after last crash in the Halemba colliery, according to the recommendation of the after-accident committee, the system was directed to this colliery for operational tests. The paper describes construction and functions of this system and gives some results of tests conducted at the Halemba colliery. The results point out the necessity of using monitoring equipment of continuous operation in mines of high dynamics of methane emission. INTRODUCTION Commonly used in Polish coal mining the methane monitoring systems of CTT/63/46 Up or CMM-20 and CMC-1 type are based on cyclic measurements with 4-minute repetition of measurements. This period has been stated sufficient from viewpoint of methane emission dynamics under normal exploatation. In these systems, automatic switching-off electrical power is performed by the surface station, i.e in case of detecting exceeded concentration value the station generates control pulse signal which actuates the switchng-off devices CRA and IZZO. Such a way of disconnection causes a considerable time delay, up to several minutes, in electric power break at hazardous areas. In the methane monitoring system with the new CMC-3 station, the different phylosophy of operation has been applied. Measurement of methane concentration is performed in a continnous way. In case of exceeding the alarm value, immediate control of the IZZO unit directly by methane monitor follows and consequently energy break without necessity of communicating with the surface station. Alarm values are set directly in methane monitor. The system ensures central powering of underground equipment from the surface, and in case of power failure the methane monitor equipped with battery operates autonomously for about 12 hours. Such an extention of the methane monitor funtionality has been achieved thanks to the use of internal microprocessor controller. The system with the CMC-3 station has been worked out in the aspect of methane hazard detection in mines exposed to gas outbursts. But after last gas explosion, according the desicion of the After-accident Commitee, the system was installed in the Halemba coliery where it underwent operational tests. Besides

Jan 1, 1993

By Brian Hester

Many Third World African countries are well-endowed with minerals - especially gold and diamonds - while only a few have important base metal deposits. For decades since colonial rule, political and economic conditions discouraged interest by Western capital. Influence from Soviet Bloc countries, however, has declined with the move toward multi-party rule. And the left wing orientation, once widely favored by Third World African countries, has almost disappeared. With International Monetary Fund (IMF) encouragement, these Third World African countries now encourage representational government and solicit western finance to expand their industries. Mining is especially encouraged. The North American mining industry is following the same trail as other capital intensive industries and looking abroad for opportunities. The Prospectors and Developers Association of Canada released figures that show exploration expenditures in that country were halved between 1987 and 1990. Figures for the United States are not so easily found but every indication points to a downward trend. While total annual expenditures on US exploration by corporations as a group are either declining or remaining constant, expenditures away from North America is increasing. Gold exploration expenditures in 1991 by the major companies tracked by Minerals Economics Group were less in the United States than for Latin America and the Southwest Pacific combined. The same study showed as much was spent in the Republic of South Africa and "Other" areas combined as in the United States. Expenditures by major corporations in these "Other" areas amount to only 5.2% of their total budget. Third World Africa is a major component of these "Other" areas.

Jan 1, 1993

By W. C. Lacy

Traditionally Australia has been a leader in underground mining methods with world standards being established at Mount Isa, Broken Hill, Kalgoorlie, and Mount Lyell. With decline in higher-grade reserves and discovery of a multitude of near-surface oxide gold de-posits attention has shifted to bulk mining of low-grade gold ores by open pit methods, heap leaching and activated carbon recovery of gold values. The paper examines historical change in mining philosophy and the economic effects of isolation.

Jan 1, 1993

By O. Ofor

Coal fines of less than 0.5 mm particle size, discarded as too fine for gravity separation, were subjected to flotation tests at varying pH and temperatures using modified dosages of kerosene as oil phase and methylisobutylketone (MIBK) as frother. Optimal coal recovery of over 74% was obtained using 200 kg kerosene and 4 kg MIBK per ton of coal fines at a pH of 9.7 and an ambient temperature of 26° C. The coal concentrate obtained under these optimal recovery conditions assayed 9.10% ash, 0.35% sulfur and 0.011% phosphorus, representing reductions in the ash, sulfur and phosphorus contents of approximately 75%, 43% and 8.3%, respectively. Its gross calorific value was 32.9 MJ/kg, its percentage of volatile matter measured 30.6 and the fixed carbon content was 66.3% (d.a.f). Caking tests showed the optimal concentrate has a standard welling number of 1 and is a Gray-King coke type C. These results show that the optimal flotation product could be utilized for such industrial purposes as steam raising or for processing in gasworks, but it would be unsuitable for metallurgical coke production.

Jan 1, 1993

By J. A. Lepinski

The FASTMETSM Process is a coal-based process for converting iron oxide fines into metallic iron. The end product, direct reduced iron (DRI) is used as a low residual charge material in electric arc furnace steelmaking. This paper describes the FASTMET Process and its potential application in the United States. Operating results from a 175 kg/h process simulator are presented. Characteristics of the end product are discussed. Process economics are reviewed along with plans for scaling-up the process to full commercial size.

Jan 1, 1993

By W. M. Shaver, W. R. Dengler

INTRODUCTION In Canada, most of the rock being broken in underground metal mines is being carried out using traditional drilling and blasting methods. Despite advances being made in hard rock boring and other, more exotic techniques, it is Dynatec's belief that the traditional methods will continue to prevail for many years to come. It is also our belief that modest research efforts expended on the traditional methods will result in substantial financial benefits to the mining and rock tunnelling businesses. Dynatec has pursued productivity improvements through the use of long rounds in both shaft sinking and lateral development. The concept of longer rounds was developed by Dynatec on the Craig Shaft Sinking Project (RETC 1991). This paper reviews the Craig Shaft Long Round success. This technology was subsequently utilized to sink the two shafts at Aur Resources with great success. The development of a Long Round Jumbo for tunnelling is a natural progression of the long round technology developed for the Craig Shaft. RECENT HISTORY OF SHAFT SINKING Shaft sinking is one of the oldest and most difficult mining methods. Due to the relatively small amount of shaft sinking in proportion to tunnelling and

Jan 1, 1993