Search Documents

By W. B. Greer, J. J. K. Daemen

Introduction The performance of seals in boreholes, shafts and tunnels is an important concern in mine safety, in the control of effluents from operating and abandoned mines and in the underground containment of hazardous wastes (Einarson and Abel, 1990; Mining Waste Study, 1988). Despite the clear need for effective seals, few documented test results are available concerning the performance of in situ seals. Some evidence indicates that horizontal or near-horizontal holes are especially difficult to seal properly (Kelsall et al., 1982). This research involved the installation, extensive hydraulic testing, removal and post-test examination of a 10-cm-long x 10-cm-diam cement grout seal in a near-horizontal borehole in limestone. The work was performed in an underground mine on Marble Peak in the Santa Catalina Mountains, AZ. A test hole was diamond cored in the recrystallized limestone of the Escabrosa formation. The hole is 33.24 m long, 10 cm in diam, and dips at 10.4°. The hole extends between two drifts and thus is accessible from both ends. Seal installation Surveys to assist in selecting the interval to seal consisted of core logging, video logging and constant-head injection tests using a straddle-packer unit. The location selected, 3 m from the lower end of the hole, had low hydraulic conductivity (3 x 10-10 to 3 x 10-9 cm/sec) and was free of significant fractures. The grout used, an expansive Class A cement, was provided by Dowell-Schlumberger, Tulsa, OK. A grout mass about 1.5 m in length was installed, with a dump bailer, above a temporary mechanical plug. Groundwater in the hole, if any, was minimal during placement. After 13 days of curing, the grout mass was partially drilled out from both ends, leaving a seal 10 cm long. Water distribution in rock mass The distribution of water and fluid pressure in the rock mass near the seal appears to be complex. The generally dry condition of the borehole and rock mass suggests that the rock mass near the seal was unsaturated prior to the injection tests of this research. The injection tests presumably created an expanding saturated zone around the seal. However, anomalously high fluid pressures, consistently recorded by one of two piezometers installed near the seal, suggest connection to a source of significant natural hydraulic head. Comparable head variations for closely spaced piezometers have been reported by others (Sowers, 1976). [ ] Seal testing The seal was tested for 3.5 years, using steady constant-head, tracer travel-time, dye-injection, head-buildup and transient constant-head tests. These tests are fully described in Greer and Daemen, 1991. In the head-buildup test, transient flow occurs through the seal (and rock mass) to a closed, water-filled interval of the borehole adjacent to the seal. The test consists of monitoring the rise in head in the closed interval until steady conditions are approached. The test may be analyzed in terms of a one dimensional analytical model to obtain the effective hydraulic conductivity (Ks) and specific storage (Sss) of the seal. Analysis in terms of an axisymmetric three-dimensional numerical model may yield properties of both the seal and rock mass.

Jan 1, 1993

By S. L. Jung, T. L. Nichols, K. Prisbrey

The problem was to evaluate the on-line detection of rock properties through acoustic emission sensors. Acoustic emission sensors, when attached to crushers, grinders, and roof bolters, are robust, economical, and relatively maintenance free. Our objective was to relate acoustic emissions to rock fracture mechanisms, including micropore closures, linear elastic deformations, and crack propagation. We evaluated acoustic emissions from steel jacketed rock cores during indentation tests. In addition we attached sensors to the rotating shaft of a rock bolter drill. A back propagation neural network "learned" rock fracture characteristics and rock type with 99% classification accuracy. A neural network's calibration and computational abilities suggest better acoustic emission sensor capabilities.

Jan 1, 1993

By K. A. Natarajan, M. K. Yelloji Rao, P. Somasundaran

The bacterium Thiobacillus ferrooxidans triggers the surface modification of sulfide minerals to provide hydrophilicity or hydrophobicity for the flotation of sphalerite and galena. The effects of initial cell concentration, period of biotreatment and pulp density on the floatability of the minerals are discussed. With galena, flotation enhancement obtained through sulfuric acid treatment was retarded by biotreatment at all cell concentrations due to chemical effects. Such a decrease occurred for sphalerite only at cell concentrations sufficiently high for bacterial attachment to the mineral surface. The variables affecting surface modification (and, thus, flotation response of the minerals) include the cell concentration used for bacterial conditioning, the period of biotreatment and the pulp density. Although bacterial growth during biotreatment was observed even in the absence of nutrients, such growth was more common in the sphalerite suspension than in the galena suspension. Cell protein estimations suggest that more cells are attached on galena than on sphalerite. Probable reaction mechanisms associated with bacterial modification are discussed.

Jan 1, 1993

By J. Hanna, J. Jung, I. J. Anazia

Electrothermal production of elemental phosphorous (P4) generates substantial amounts of highly toxic phossy water and sludges. Because of their high phosphorous contents and lack of reliable processing technology, large tonnages of these hazardous wastes have accumulated from current and past operations. To date, the sludges are stored in ponds or above ground in special containment vessels at various locations around the country. Two samples of electric furnace phosphorous sludge (obtained from the Tennessee Valley Authority (TVA) in Muscle Shoals, AL and FMC Corporation in Pocatello, ID) were investigated using physical separation techniques to recover the elemental phosphorous and to render the residual material nonhazardous. The techniques tested include sizing, froth flotation and dispersed air oxidation. Flotation and sizing produced concentrates containing 69% - 90%P4, with recovery in the range of 60% - 87%. Dispersed air oxidation of the fines and tailings products was effective in the removal of an additional 10% - 15% of the P4 in the sludge.

Jan 1, 1993

By J. E. Litz

The hydrometallurgy review did not arrive in time for publication in the May issue. 1992 was not a banner year for hydrometallurgical installations or new hydrometallurgical developments. Installation of copper solvent extraction/electrowinning circuits were under construction or began operation in Nevada (Yerrington ), Arizona (SilverBell), Chile (Copiapo and Escondida), Peru (Toquepala and Cuayone) and Australia (Girilambone). These installations will produce more than 100 kt/a (110,000 stpy) of cathode copper. Several new heap leach gold facilities using conventional technologies were announced or were put into operation. New technologies undergoing widespread testing include biological oxidation of low-grade ores in a heap leach mode and evaluation of new agglomerating agents.

Jan 1, 1993

In 1992, the United States economy grew at a rate of 2%. The Gross Domestic Product rose to $5,946 billion. With 257 million people - 635,000 in mining including petroleum - the United States has more than 100 million dwelling units and more than 190 million licensed motor vehicles. New private housing starts rose I 1 % to 1.2 million units. New car production rose 4% to 5.7 million units. Truck and bus production rose 20% to 4 million units. The rate of inflation was 3.5% and the prime rate of interest was 6.25%. The Producer Price Index (1982 =100) was relatively unchanged from 1991 as follows: fuels and related products and power 80, metals and metal products 119, chemicals and allied products 126 and nonmetallic mineral products 117. Energy Imports of crude and refined petroleum, costing $50 billion, rose 3% to 455 Mm3 (2.9 billion bbl). Domestic petroleum production fell 1 % to 582 Mm3 (3.5 billion bbl). Petroleum supplied about 41 % of US energy, natural gas 24% and coal 23%. Coal production, 60% from surface operations, rose 1 % to 914 Mt (1 billion st). About 78% was used to generate electricity and 3% was coked. Exports valued at $4 billion included 57 Mt (63 million st) of metallurgical coal and 39 Mt (43 million st) of steam coal. Ura¬nium mining, including recovery from phosphates, fell 18% to 3 kt (3300 st) U308.

Jan 1, 1993

By Ernest Peters

To model the zinc pressure leach, equations have been written that describe the rates of individual reactions taking place, including (a) oxygen mass transfer, (b) ferrous oxidation by dissolved oxygen, and (c) ferric reactions with ZnS and other minerals. In the continuous process, at steady-state, these take place at the same rate, and so the equations can be solved simultaneously. Model calculations using simultaneous equations are shown in graphical form to demonstrate the effect of different variables on the leach performance.

Jan 1, 1993

By M. Z. Rashad, H. A. El-Sageer

The intersections of numerous joint sets at the surface of tunnels of the Abu-Tartour project in Egypt create blocks of irregular shape and size in the rock mass. Although most of these blocks are unable to move into the free space of the tunnel, a few key blocks are capable of such movement. In addition, as soon as they move, some restrained blocks will be liberated. The aim of this work is to find the removable key blocks of the walls, floor, roof and corners of a portion of the tunnel under jointed surface rocks and then determine the best tunnel direction.

Jan 1, 1993

By James E. McTurk, Sheldon B. Bland, Roger E. Melley

During the first fifteen years of operation at the Syncrude facility in northern Alberta, numerous improvements have been made in the field of ore conveying. The unique nature of the material conveyed coupled with the wide range of environmental conditions encountered results in a number of unparalleled challenges. Most of the improvements have been brought about with the use of detailed field evaluation. This paper outlines some of the programs which have been run to optimise belt and system construction, and conveyor performance and utilization.

Jan 1, 1993

By M. K. Han, K. N. Han, P. B. Queneau, W. J. Dawson

The development and scale up of hydrothermal synthesis processes for manufacture of high performance materials is discussed. Traditional hydrometallurgical processes are reviewed, leading into a discussion of process development concerns for manufacture of modern materials. Three case studies are presented, including a piezoelectric ceramic, barium titanate for multiyear capacitors, and high purity chromium metal. Factors for selection of reactor design are presented, as well as results of scale-up studies on the three products.

Jan 1, 1993

By Joseph Rosta

The gold and silver review did not arrive in time for publication in the May issue. Gold The gold market generally was listless in 1992, although investors returned to the metal in the fourth quarter. The gold price declined for the second year in a row, averaging $11.05/g ($343.76/ oz), 5.2% lower than the $11.65/g ($362.44/oz) seen in 1991. The average price has declined more than 23% since 1987, when gold averaged $14.36/g

Jan 1, 1993

In 1992, United States mine production of barite decreased 8.5%. Barite consumption, sold or used by grinding plants, decreased by 36.9% and imports decreased by 61.6% vs. 1991. World mine production decreased 1.5%, according to the US Bureau of Mines. The value of domestically produced barite, f.o.b. mine, decreased 11.9% according to the Bureau. The declared value, c.i.f. United States port, of all imported crude barite during 1992 decreased from $42.35/t ($38.42/st) in 1991 to $40.09/t ($36.37/st). Nevada continued to be the leading producer of barite with 88% of the total, followed by Georgia and Missouri. It is estimated that 80% of the domestically mined barite was used as a weighting agent in drilling fluids. The remaining 20% was used in barium chemicals, glass or as a filler. Most of the production from Missouri, Georgia and Ten¬nessee was used in the non-oilfield sector. Of the total barite used by grinding plants and chemical manufacturers, it is estimated that 90% was used in drilling fluids and 10% in the non-oilfield sector. This included barium chemicals and fillers in paper, plastics and glass. The tonnage consumed in the drilling fluids market decreased due to the lower average rig count during 1992. The average number of rotary rigs operating (717) was 16.6% less than the 1991 average of 860 in the United States. Crude barite imports were 518 kt (571,000 st), 61.6% less than in 1991. Imports accounted for 44.7% of the barite consumed (apparent) in the United States. During the year, China continued to be the leading exporter of crude barite ore to the United States with 67.2% of total crude ore imports. India followed with 31 %, and others with 1.8%. About 90% of the imported barite ore was used in the oilfield sector. Ground barite imports decreased from 46.3 kt (51,000 st) to 30.9 kt (34,100

Jan 1, 1993

By Husheng Li, Zhongli Wu

This paper discusses the fundamental strategies adopted in the simulation package FIRES developed for ventilation simulation under mine fires. These fundamental strategies include (1) fire characteristic curves specifying the development of a mine fire with time, (2) simulation of fume spread in a ventilation system, (3) determination of the aerodynamic effects of mine fires on flows; and (4) dynamic simulation of flow state under mine fires. The major functions of the simulation package are also addressed. The package has been used to simulate an experiment of mine fire. A comparison is made between the simulation results and the measured data.

Jan 1, 1993

By Y. Zimmels, C. Feldman

Closed-circuit grinding processes are considered in the context of a reactor-separator circuit that involves multifraction streams and products. Because grinding circuits are low-efficiency, capital-intensive operations, modeling to maximize their economic return is appropriate. An attempt to develop and test such a model is presented in this work. The model relies on process simulation for both the mill and the separator, in conjunction with constraints imposed by product specifications. The grinding process was simulated using breakage functions, which provided complete data on the feed and product of the mill. A cyclone bank used as the separator was also simulated using known models. The overall process model provided a complete simulation of the multistream grinding and separation process. The process model was then incorporated into an economic model that predicts grinding cost, subject to process constraints, for a given set of operating variables. The model facilitates economic optimization of the grinding process as it relates to process variables and process hardware.

Jan 1, 1993

By Garry Keizer

The Cortez gold mine is located in Lander County, NR, about 130 km (80 miles) southwest of Elko. Cortez Gold Mines (CGM) is a joint venture between Placer Dome US Inc. (60% operator) and Kennecott Corp. (40%). The claims that supply oxide and refractory ore feed to the Cortez milling facility are located in both Lander and Eureka counties. These include the Cortez and Horse Canyon deposits, all operated by the joint venture. Other deposits outside the CGM claim area include Fire Creek, Buckhorn, Gold Bar and Tonkin Springs. These deposits all occur along the Battle Mountain-Eureka Trend. History Mining in the Cortez district began in 1862 with the discovery of high-grade silver ores. Grades in the hundreds of ounces per ton occurred in an area 7 km (4.5 miles) southeast of the current CGM mill site. Underground mining through the Garrison and Arctic tunnels provided the bulk of the ore production between 1864 and 1895. To a lesser extent, the Mill Canyon area also supplied ore until 1930.

Jan 1, 1993

By R. J. Wesely, A. D. Zunkel, Tracy B. Braun, Philip L. LeHoux

An overview of gold processing operations at Barneys Canyon Mine is presented with particular emphasis on ore agglomerating experience, leaching and metallurgical accounting practices, and carbon column plant operating approach. The mine, located thirty kilometers from downtown Salt Lake City, is just eight kilometers north of the Bingham Canyon copper mine. Mining was initiated in February 1989 and the first gold was poured in September 1989. Through year-end 1992, approximately 7 million tonnes of ore have been processed and 12,000 kg of gold have been produced. Gold recovery is in excess of 85 percent.

Jan 1, 1993

By N. I. Aziz, B. Srinivasa Rao, R. N. Singh

The control of respirable dust and its subsequent exposure to miners is essential for improved safety in longwall mining. The extensive variation in face conditions and operations of longwall make numerical modelling an attractive approach in both the development and evaluation of dust control devices. Three dimensional finite element computational fluid dynamics code FIDAP was used to model air velocities and the effect of dust control techniques on dust concentrations at a typical longwall face. The effect of shearer body on airflow characteristics in a longwall face was analysed with both antitropal and homotropal ventilation systems. Path traces of particles introduced near the shearer drums was also simulated. Initial modelling results were validated using field trial results at three operating longwall faces. Results of simulations tallied very well with the field results.

Jan 1, 1993

By J. A. Brierley, Arpad E. Torma, Victor C. Storhok, C. L. Brierley, Batric Pesic

Chemical and electrochemical studies were performed during bioleaching of cobaltite concentrate with Thiobacillus ferrooxidans. The two principal minerals present in the concentrate were pyrite and cobaltite (CoAsS). During chemical studies, the effect of pH on dissolution rates was examined under uncontrolled and pH-controlled conditions. It was found that in the pH range 1.5-3.0 there was no pH effect if the initial pH was not controlled (maintained). When the initial pH was controlled, the leaching of Co, As, and Fe depended strongly on pH. Electrochemical studies were performed by using cyclic voltammetry and constant potential techniques. A sequential reaction mechanism was proposed for dissolution of cobaltite.

Jan 1, 1993

By Derek G. Cieplinski

Regenerative conveyors with complex conveyor profiles place unusually stringent demands on the starting drive control. Depending on the nature of the conveyor loading, the drive must either provide a positive driving force to overcome conveyor friction and gravitational forces if the belt is empty or the inclined sections are loaded, or it must provide a retarding force to resist the gravitational load of decline sections to control the acceleration rate. This paper discusses the requirements of regenerative conveyors, reviews the working principals of fluid couplings, and examines their interaction by means of a case study of a 1700 m long regenerative conveyor utilizing a fluid coupling with a proportional brake control to provide controlled starting and stopping under all load conditions.

Jan 1, 1993

By Michael J. Feltes

In mining operations, conveyors hold one of the most important keys to productivity. Sudden belt or belt-splice failures and extended repair downtimes can contribute to low material-handling system availability. Consequently, operations and maintenance personnel should have a thorough understanding of the available splicing and repair alternatives and how each method can affect the productivity and cost-effectiveness of their operation. The two primary methods of joining belt ends - vulcanization and mechanical fastening - affect the likelihood of sudden failure and repair times in different ways. The time-honored method of vulcanization remains popular in many conveyor-intensive underground and above-ground mining operations around the world. At first, vulcanization may seem attractive because, when done properly by trained and experienced craftsmen, it can match the original belting fairly closely and give the splice a smooth, continuous surface with no edges or seams to invite snagging.

Jan 1, 1993