Search Documents

By Eugene V. Cilento, George B. Georgellis

The hypothesis that freshly-sheared quartz makes it more reactive in lung tissue than aged quartz was tested by its ability to stimulate superoxide anion (02-) release from single adherent pulmonary alveolar macrophages (PAM). Fresh quartz was prepared by grinding for 30 min and then used within 2 hr, while stale quartz was from the same stock but aged 15 days prior to use. Also, dipalmitoyl lecithin (DPL), the major constituent of lung surfactant coating the alveoli surfaces, was coated onto the particles. Release of 02- was measured after 40 and 180 min of direct contact with quartz dust (225 µg/ml). Fresh quartz was more reactive than aged quartz, as indicated by the 78 and 63% increase after 40 and 180 min, respectively. A time delay and suppression of 02- release was observed in the ability of the DPL- coated fresh or stale dust to stimulate PAM. These results supported the hypothesis that the natural process of surfactant coating of inhaled particles in the alveoli may play a role in their phagocytic removal by PAM.

Jan 1, 1991

By R. Hogg, A. C. Maffei, D. T. Ray

Based on standard population balance models for agglomeration and size reduction processes, a simplified model has been developed to describe simultaneous growth and breakage in the flocculation of agitated suspensions. The results of semi-batch flocculation tests have been used for estimation of the model parameters and empirical relationships have been obtained to describe the effects of process variables and to establish scale-up criteria. Application of the model to the design, operation and control of continuous flocculation processes is discussed.

Jan 1, 1990

By M. G. Ayat

A novel tracing technique employing specifically prepared trace particles has been applied to coal preparation separatory systems. The technique employs individually prepared trace particles representing specific known sizes and densities of coal particles. These trace particles are injected into the feed, to the processing circuit, and are then detected at locations in the coal product and refuse streams. It is anticipated that on-line input of the generated partition data will be linked with computer technology to provide rapid analysis of the processing efficiency, and to allow for process control. This tracing technique can revolutionize many processing operations from the diagnostic viewpoint as well as from the coal processing standpoint.

Jan 1, 1986

By Frank E. Chase

Preventing pillar squeezes, massive pillar collapses, and bumps is critical to the safe and efficient recovery of coal during room-and-pillar retreat mining. To help prevent these problems, the U.S. Bureau of Mines (USBM) has developed the Analysis of Retreat Mining Pillar Stability (ARMPS) computer program. ARMPS calculates stability factors (SF) based on estimates of the loads applied to and the load-bearing capacities of, pillars during retreat mining operations. The program can model the significant features of most retreat mining layouts, including angled crosscuts, varied spacings between entries, barrier pillars between the active section and old (side) gobs, and slab cuts in the barriers on retreat. It also features a pillar strength formula that considers the greater strength of rectangular pillars. The program may be used to evaluate bleeder designs as well as active workings. A data base of 110 pillar retreat mining case histories has been collected across the United States to verify the program. It was found that satisfactory conditions were very rare when the ARMPS SF was less than 0.75. Conversely, very few unsatisfactory designs were found where the ARMPS SF was greater than 1. 5.

Jan 1, 1995

By F. L. Jackson

When using perlite as an insulation, it is important to determine the requirements for different applications as this influences the processing of the perlite. In cryogenic application, perlite properties of low density and fine particle size are desirable, while loose fill insulation applications require similar properties and water repellency. However, in perlite insulating concrete applications, a coarser particle, of higher density, is required to provide improved compression strength. The essential properties of perlite including particle size, density, and surface treatment are discussed in relation to the various insulation applications. Also, typical mineral processing and manufacturing techniques are reviewed.

Jan 1, 1987

By Carl (Original by) Hrovatic

Land is a precious resource and should be treated as such by all members of our society. The soil covering this earth is only a very thin outer layer, varying in thickness from a few inches to a few feet and covering the rocks and minerals lying beneath the surface. The wise use of this valuable commodity is the responsibility of everyone. Many everyday activities disturb e earth's surface. Examples are highway construction, housing and commercial developments, agriculture, and various types of mining. This chapter discusses the relationships of the environment to land as it applies to surface operations in the coal industry. Mining by surface methods disturbs, for a brief period of time, thousands of acres of land annually. In addition, refuse piles, slurry ponds, abandoned mine structures, unprotected mine openings, and unsightly cleaning plants can also adversely affect land unless properly handled.

Jan 1, 1981

By S. K. Kawatra, S. K. Valluri, S. J. Root

Common carbon dioxide capturing reagents, such as amines and sodium hydroxide, are expensive, toxic, and energy intensive to regenerate. We have added frothers to a sodium carbonate solution in order to increase the surface area available for CO2 transport within the packed bed of a counter current scrubbing column. Addition of frothers has improved the performance of sodium carbonate scrubbing solutions to be on par with sodium hydroxide scrubbing solutions. This novel enhancement of a relatively inexpensive CO2 capture-regeneration cycle shows potential to allow plants to turn a profit by sequestering a waste product. These results are discussed in detail in the following manuscript. INTRODUCTION The combustion of fossil fuels converts chemical energy to thermal energy. CO2 is produced as a byproduct of the reaction. 80% of the world’s electricity is produced by using this thermal energy to power a generator, accounting for 40% of global carbon dioxide emissions. In an effort to stabilize the rising atmospheric CO2 levels, researchers are investigating the application of carbon capture and storage (CCS) systems in power plants. [1] Efforts to capture CO2 at some power plants have been successful, but the cost of installing and operating the required equipment is high. As such, very few power plants have CCS systems. If CO2 can be captured and processed into a product that can be sold at a profit, installing CCS systems in power plants will be a very attractive business decision. In order for the sale of captured CO2 to become a profitable venture, the cost of capturing the CO2 from a flue gas must be reduced. BACKGROUND The most common method for separating CO2 from a flue gas is by passing it through a counter-current packed bed scrubbing column. The flue gas enters the bottom of a column while a solution of a chemical with properties advantageous to the absorption of CO2 is pumped to the top. The fluids interact in a packed bed, where the CO2 is transported from the gas to the liquid. CO2 is an acid gas, so it is common for the scrubbing solution to be alkaline in nature in order to neutralize the carbonic acid that is formed when it is dissolves into water. The exhaust exits the top of the column free of carbon dioxide, which exits the column in the scrubbing solution, reacting or complexing with the absorbent. Figure 1 is a schematic drawing of a CO2 scrubbing column. It shows the molar flowrates and compositions of the gas and liquid at the bottom [1], the top [2], and an arbitrary height in the column [Z]. [2,15] L is the molar flowrate of liquid at any point in in the column. G is the molar flowrate of gas at any point in the column. Since the CO2 is transported from the gas to the liquid, L and G are variable with respect to height. To simplify calculations, the CO2 free molar flowrates Ls and Gs are often used. X is the fraction moles of aqueous CO2 per mole of CO2 free liquid. Y is the fraction moles of gaseous CO2 per mole of CO2 free gas. Figure 2 is a composition diagram of the scrubbing column depicted in figure 1.

Jan 1, 2019

By Samuel Polinsky, Lawrence W. Bierman, Wayne Perkins

[A column float beneficiation plant using 9, 8.5 foot diameter, cells was constructed by the Simplot Company and the Smoky Canyon Facility in the fall of 1986 and has been in operation since May of 1987. The float beneficiation process was developed jointly by the Simplot Company and the Bureau of Mines (Salt Lake City, Utah) which incorporates the Bureau's bubble generator design and chemistry system based around the reverse float technology, (Albany Bureau of Mines, Application of Carbonate-Silica Flotation Techniques to Western Phosphate Materials, Rule, Dallenbach , Larsen, RI8728, 1982) . This chemistry has been modified by Simplot in both patented and unpatented improvements. The objective of the beneficiation process was to reducethe A1203 content in the overall pipeline concentrate by 0.2 wt z. Therefore, a process stream was identified in the mill circuit which provided an opportunity to isolate and treat 1100 tons per day of poor quality phosphate concentrates The process allows recovery of approximately 15% of the mill concentrates, otherwise unsuitable for fertilizer production. The alternative would have been to waste this ore. Wasting would have resulted in considerable ore loss, increased mining costs and required additional products grinding. ]

Jan 1, 1989

By I. M. Morsi, S. Z. El-Tawil, O. A. Fouad, K. A. El-Barawy, M. B. Morsi, M. M. Nasr

Upgrading of a low-grade titanium slag (~55% TiO2) with high silica, calcia, magnesia and iron contents has been studied using sulphation roasting technique using SO2/air gas mixture followed by hydrochloric acid leaching. XRD analysis of the sulphated slag reveals the presence of kennedyite (Fe2O3. MgO. 3TiO2), rutile (TiO2), calcium sulphate (CaSO4) and calcium silicate (3CaO.SiO2) phases. The residue after leaching contains mainly kennedyite, rutile phases and free silica with traces of calcium silicate phase. Synthetic rutile that has about 83% TiO2 can be produced at the optimum conditions. Thermodynamic calculations give rational explanations of the obtained results.

Jan 1, 2005

By Cal D. Iles

Decreasing ore grades and increasing labor and material costs have seriously eroded the economic vitality of many mining operations. Coupled with global economic stagnation and recession in the early 1980's, these conditions have forced reevaluation of operating strategies and methodologies with the objective of remaining competitive in a world marketplace. A concept offering large potential benefits is hardrock portable crushing and conveying. Implementation of this system at Duval Corporation's Sierrita open pit copper-molybdenum mine (Figure 1) has significantly reduced mining costs, becoming a major part of Sierrita's cost reduction strategy. Located 48 km south of Tucson, Arizona, the 209 000 t/d property has one portable 60x89 gyratory ore-crusher in operation with tentative plans for two additional units.

Jan 1, 1985

By Angela Binder, Oliver Langefeld

"The future of mining will be characterized not only by the application of modern technology, but also by the harmonization of economic, environmental and social issues. These areas set major future challenges which are complex and demand extensive knowledge. As an example, mining of highly complex orebodies for the supply of often critical raw materials, needs to consider technically demanding and cost-intensive extraction issues. The amount of tailings, which need to be stored, increases with the amount of ore mined. Therefore, the negative impact on environment and society increases. Hence mining becomes expensive with regard to all three aspects: economy, environment and society. In view of a sustainable mining practice this challenge should be used as an opportunity. The positive impact should be maximized for present and future generations. The objective is to create and use the mining openings in an optimum way related to sustainability. The approach of Blue Mining, which focuses on energy and ergonomics in the field of Sustainable Development, enhances the closure planning by recommending subsequent usage of such openings for energy storage. The approach fosters among others the implementation of the 7th Goal for Sustainable Development defined by the United Nations with the assurance of access to affordable, reliable, sustainable and modern energy for all. The usage of underground storage increases the stability of solar and water power usage, which are otherwise unreliable. Blue Mining embeds these issues in the main planning effort long before groundbreaking. This approach involves experience from past and current projects. This paper introduces the concept of Blue Mining with respect to post-mining utilization of a mine for energy storage. Methods and perspectives are presented with examples covering best-practices and lessons-learned."

Jan 1, 2017

By W. David Tyler

Any mining or engineering-construction excavation that extends below the water table must be dewatered. In many situations, the ground is of low permeability or the workings extend only a short distance below the water table. So water removal can be handled easily and economically by using mobile centrifugal pumps. However, there is an increasing number of mines that have a continuous high flow of water into the workings. Controlling this flow can significantly increase the cost of ore production. Successful implementation of any major dewatering scheme will ultimately rely on a clear understanding of the local geology. This understanding is necessary before an interpretation of ground water conditions can be made. It will dictate which dewatering methods are feasible. Once the geology and the ground water system are known, the scope and timing of the dewatering measures can be varied with the mine plan. Ground water modeling can assist in optimizing the dewatering system, though the precise objective of each model should be clearly defined. Production wells must be sited and drilled so that individual well efficiencies are high. Any lost efficiencies will translate into higher operating costs. Each well must be designed for maximum long-term control of the water table, and pumps sized to operate under continually changing heads. Finally, the investment in each production well must be protected during the mining process.

Jan 1, 1991

By S. F. Diehl

Weathered mine waste consists of oxidized primary minerals and chemically unstable secondary phases that can be sources of readily soluble metals and acid rock drainage. Elevated concentrations of metals such as Cd, Cu, Fe, Mn, Ni, Pb, and Zn are observed in deionized water-based leachate solutions derived from complex sedex and Cu-Pb-Zn mine wastes. Leachate (USGS FLT) from the Elizabeth mine, a massive sulfide deposit, has a pH of 3.4 and high concentrations of Al (16700 ug/L), Cu (440 ug/L), and Zn (8620 ug/L). Leachate from the sedex Faro mine has a pH of 3.5 and high concentrations of Al (2040 ug/L), Cu (1930 ug/L), Pb (2080 ug/L), and Zn (52900 ug/L). In contrast, higher-pH leachates produced from tailings of polymetallic vein deposits have order of magnitude lower metal concentrations. These data indicate that highly soluble secondary mineral phases exist at the surface of waste material where the samples were collected. Sulfide minerals from all sites exhibit differential degrees of weathering, from dissolution etched grain rims, to rinds of secondary minerals, to skeletal remnants. These microscale mineral-dissolution textures enhance weathering and metal leachability of waste material. Besides the formation of secondary minerals, sulfide grains from dried tailings samples may be coated by amorphous Fe-Al-Si minerals that also adsorb metals such as Cu, Ni, and Zn.

Jan 1, 2011

By R. G. Lundquist

The idea that fragmentation for mineral processing results from some tradeoff between increased drilling and blasting and increased load on the primary crusher is well known. In a previous paper (Lundquist and Konya, 1963) the authors reported on the results of a laboratory scale study which attempted to quantify this tradeoff in energy terms. If we look only at the production of new surface area, blasting is 1700 times as energy efficient as crushing. On an energy cost basis, crushing is 57 times as expensive per unit surface produced as blasting with dynamite and more than 700 times as expensive as blasting with ANFO. The comminution process at an open pit operation starts with the drilling of blast holes and ends after the material has gone through the fine grind circuit. Operators usually break the process into several separate operations and do their cost analysis based on this approach. Often drilling and blasting is considered as one system and crushing and grinding are considered as one or two separate and independent systems. Operators will independently optimize each system. The cost for the drilling and blasting system is obvious in operations which use contract drillers to do the drilling and either contract the blasting to a distributor or do the blasting themselves. The cost of rock breaking in this manner is readily available since the contract driller will supply a monthly drilling cost to the operation and either the distributor who is contracting the blasting or the distributor who is supplying the powder to the blasting operation will also supply a monthly billing. In either case, the costs can easily be seen on a monthly or per ton basis. They are not difficult to compute even when drilling and blasting are done entirely in-house.

Jan 1, 1985

By R. H. T. Garnett

Reserve estimation is a process that commences with sampling and culminates in the issuance of a reserve statement. The tin, gold and diamonds that occur as marine placers on the continental shelf are low grade with very erratic mineral distributions. Sampling, using a variety of special equipment, determines the extent and grade of the mineralization. The sample size is important, especially for diamonds. Together with the sampling density, it determines the accuracy of the grade estimate. Bulk sampling is a confirmatory process. The choice of mining equipment, either new or developed from onshore activities, dictates the unit costs, the cutoff grades and the selectivity of extraction. Thus, the size of the blocks that comprise the mining plan and the reserves are determined. A variety of estimation methods of different reliability are available, with the most sophisticated being kriging. Dilution and losses during mining must be taken into account in estimation, and a grade-volume curve should be constructed. Diamond deposit estimation also involves an extra variable, the dollar value of the stones. During and after mining, essential feedback on the accuracy of un estimation may be given by the RIE factor and by a mineral balance. Reserve estimates are required for several reasons and may be subject to public disclosure. The use of the correct definitions is, therefore, important.

Jan 1, 1999

By Hung-Kei H. Lam

Rubidium and cesium were discovered by Bunsen and Kirchhoff about 100 years ago. These two elements are by no means as abundant as sodium or potassium. Their occurrence in minerals is widespread, but usually as minor constituents. There is no known specific ore containing rubidium, but rubidium is found replacing the. other alkali metals in .some minerals.. Perhaps the highest concentration of rubidium found in one mineral is in lepidolite, KLi(OH,F)2A12Si3010, which contains from 0 to 3.5%*Rb20. 0n the average, lepidolite contains about 0.5% Rb20. Other sources of rubidium are carnallite, KMgCl3?6H20; pollucite, H20.2Cs20.2AI203.9SiO2; rhodizite, R20.2A1203-3B203; biotite, H2K(Mg,Fe)3A1(Si04)3; sea water, rivers, marine and fresh water organisms, soils, and plants. Cesium, even though it is the least abundant. of the stable alkalies, has a specific ore. Pollucites a hydrous cesium aluminum silicate, may con¬tain as high as 42.5% Cs20, although again, the average Cs20 content is about 25% among the handful of known deposits. Other cesium-containing minerals are lepidolite and carnallite. Rubidium and cesium are very much like potassium in chemical properties, consequently, they are hard to separate. Because of the difficulty in obtaining pure cesium and rubidium compounds coupled with the scarcity-of supply, prices were high and the two elements enjoyed little industrial use. Just before the Second World War, the world. supply of rubidium and cesium, from Germany, was a matter of tens of kilograms per year and prices were about

Jan 1, 1959

By Howard L. Hartman

Introduction The federal government's declining role in funding research has created a critical dollar gap for university departments of mining engineering. Industry, too, is affected by the drought. Research is lagging. Hardpressed universities are going to the private sector for funding. Mining companies should not shower universities with philanthropy, but a research partnership should be contracted on a pay-as-you-go basis. A model exists at The University of Alabama (albeit not in mining) that could be adopted by the mining industry. An equal partnership arrangement between a university and an industry for conducting research is proposed. The concept is not that a corporation sponsors and a university performs the research. Nor does it call for educational contributions or giveaways from industry. Rather, the corporation and the educational institution enter into a cooperative research endeavor, a full and equal partnership. Both parties contribute and both share the benefits. A key to the relationship is that it has a single objective: it must generate profits or reduce costs for the company. Working Model Recent literature is replete with examples of proposals for joint research endeavors, involving both contracts and grants, between industry and universities (Bronwell, 1971; Bugliarello, 1978; Branscomb, 1981; Sanford and Holland, 1982). They are all good proposals and offer something to both parties. They are, however, not widely supported. Few have received a favorable nod from the US mining industry. Though it may be logical, for example, to remake the American Mining Congress (or some new consortium) in the mold of umbrella-type industry organizations to fund cooperative research with mining institutions, such proposals have never flown. What model, then, will work? First, look for a model that has worked in industry in general. Second, seek to apply it to mining specifically. There is a model project that satisfies the first of those criteria. It is a project complicated by a third party, in addition to a corporation and a university. In January 1983, the "Factory of the Future Project" was initiated between The University of Alabama (UA) and General Motors Corp. (GM). The United Auto Workers (UAW) is a third party to the agreement. The factory was GM's Rochester Products Division manufacturing plant in Tuscaloosa, AL, also home of UA's main campus (Fig. 1). Saving a Plant The agreement came about at the initiative of GM and the UAW. Faced with having to close the plant because of excessive production costs, company and union officials proposed to the university that an applied research facility be established at the plant. The university would operate the laboratory, dedicated to $470,000 a year cost reductions for the company. The school would lease the 5.1 km2 (55,000 sq ft) space for $470,000 a year for three years. Any savings effected by the university's research effort would be credited toward to the rent. GM said the small factory, which made replacement carburetors

Jan 9, 1984

By David D. Eyer

Since the decade of the 1990s is nearly upon us, I have focused on what I see are the likely trends featured in new large underground coal mines 10 years from now. I do this from the vantage point of having been involved in the installation of large mines for more than twenty years. Little of the equipment resources we have available today was unknown when I entered the coal business in 1960. There were continuous miners, longwalls and diesel-powered equipment in Europe, monitoring systems, computers, heavy media separation systems, froth flotation and conveyors then as there are now. A substantial evolutionary process has occurred with these and other mining machines and processes. Some evolved only to die out, such as boring-type continuous miners; others, such as longwall systems, flourished. My intuition tells me that since there have been largely evolutionary rather than revolutionary developments in the near past, the same is true of the future, at least for the next 10 years. In other words, the elements of what are in the future are with US now. Some, such as computer-based applications, may evolve beyond our wildest dreams -but I doubt it.

Jan 1, 1988

By J. M. Stewart

The incidence of heat stroke in the South African gold mining industry is today small (less than 1 in 10 6 shifts worked). Acclimatization and selection procedures have been developed and applied throughout the industry, underground working conditions have, and are being improved, and personnel are to-day made more aware of heat stress and its consequences than ever before. Although these actions have, over the years, brought about a steady reduction in the incidence of heat stroke (see Figure 1) the small incidence of heat stroke which persists indicates that heat stress is still a problem. This realization provides the stimulus for the work presented in this paper, which has as its primary objective the development of reliable heat stress limits for men working in South African gold mines. [ ] In keeping with recent trends3I4 the approach followed in this paper is based on the physical principles of heat transfer. Detailed studies of heat transfer from humans have been undertaken,5-l1 and certain of the results form an important aspect of this Paper -

Jan 1, 1980

By O. A. Bascur

An expert process operation advisor system can increase plant efficiency, even in a complex, natural environment where not all elements of the production process can be measured directly. This system, develaped and tested in a Frasch process sulphur mine, monitors key process variables with extended qualitative pattern processing and provides on-line advise to the operators of sulphur production wells. An expert system framework captured common sense rules generated from years of experience obtained in the operation of a sulphur well monitoring system. The existent operating procedures were enhanced by process analysis using a qualitative modeling approach which provided extended rules for on-line classification of a well operational status and an expert alarm system. The methodology for development and implementation of the process advisor is presented in this report. Qualitative process modeling, statistical process control and heuristics were incorpomted into the process advisor resulting in a more efficient use of heat, an extended well operational life and the resulting cost savings. The computer process advisor also allowed the operator to concentrate his attention on the weak wells or wells in trouble. A process management system improved plant operation by automatically storing well data into a commercial database for operator validation. The enhanced relational data base system provided valuable and timely information for planning and decision making. The synergistic combination of on-line process analysis tools, expert control systems and database technology is shown to facilitate the flow of materials, energy and infomation in a modern plant.

Jan 1, 1990