Search Documents

By Terry L. Muldoon

On July 7, 1971, noise regulations for underground coal mines were implemented under provisions set forth in the Federal Coal Mine Health and Safety Act of 1969. These same regulations now also apply to coal mine surface facilities. In August 1971, in anticipation of these regulations, the Bureau of Mines, through the cooperation of the mine operators, conducted extensive noise surveys in three coal cleaning plants. The survey was conducted in an attempt to identify those occupations where exposures would exceed the proposed regulations.

Jan 1, 1972

By M. Hepokoski, M. Klein

"Mine refuge shelters are designed to protect mine workers from hazardous environmental conditions after a mine disaster, but high temperature and humidity levels inside these shelters may pose a significant safety risk. Due to the safety risks associated with human testing, detailed thermal models of shelters and human occupants have been developed using TAITherm simulation software. These models are used to predict the temperature and humidity within the shelter resulting from metabolic heating, evaporation due to sweat and respiration, moisture and heat from the shelter’s carbon dioxide scrubbing system, and heat transfer within the shelter. A detailed human thermoregulation model simulates the sensible and latent heat generated by the shelter occupants, and predicts the occupant’s body core temperature and moisture lost due to sweating and respiration. This information is used to assess the safety of the shelter. This paper presents the technical details of the human thermal model, validation comparing the human model to human subject test data, and results of a mine shelter analysis. IntroductionPortable mine refuge chambers are used in U.S. coal mines to provide protection to mine workers from hazardous conditions following a traumatic event. Although these shelters are designed to supply clean air and sustenance for up to 96 hours, prolonged exposure to the mine shelter environment itself can pose a substantial risk to human safety. Heat generated by the shelter occupants combined with heat from the carbon dioxide (CO2) scrubbing system can raise the shelter interior temperatures and relative humidity to dangerous levels that can lead to heat stress in humans. Unfortunately, the thermal burden associated with mine shelter exposure is not well characterized due to potential hazards associated with underground human subject testing. In order to assess the thermal burden on people within a mine shelter environment, a detailed thermal model was created to accurately predict the temperatures and humidity levels within the shelter, and the impact of these environmental conditions on human occupants. The model consists of a mobile inflatable tent-type mine shelter with 23 humans, and includes the surrounding mine environment. The thermal simulations were performed using a validated commercial heat transfer prediction computer software. Additionally, a module of the software provided the capability to simultaneously model the thermophysiology of 23 unique humans contained within the mine shelter. The human thermal models accounted for the thermal interaction with the environment and provided a core temperature response prediction that can be used to evaluate survivability in heat stress situations (U.S. Army, 2003). The models can also be used to determine maximum occupancy in order to maintain safe temperature and humidity levels inside the shelter in specific mine environments, to optimize shelter size for maximum heat dissipation, or to simulate active cooling systems."

Jan 5, 2017

By Q. Feng

"Efforts have been tried to apply the mixture of mine tailings and fly ash as construction materials. Through the present investigation, a protocol to make construction materials using the mixture of mine tailings and fly ash has been set up. The experiment results of the present work also help set up the working conditions such as activation temperature and time, the concentration of NaOH, the addition of Ca(OH)2, forming pressure, mine tailing to fly ash weight ratio, curing temperature and curing time. The findings of the present work provide a novel method for the geopolymerization of the mixture of mine tailings and fly ash as construction materials, such as bricks for construction and road pavement. INTRODUCTION In mining activity, after the valuable materials are extracted from ores, millions of tons of solid rejects, i.e., mine tailings, are stored in the tailings dam, which occupies a huge area of land and leads to high monetary, environmental and ecological costs. For example, the impoundment of mine tailings can bring with serious environmental problems such as mine dust and tailing dam failure. On the other hand, the making of general construction material results in a lot of greenhouse gas emission. Therefore, it is of great interest to utilize mine tailings, for which a lot of energy has been consumed during the comminution process, as construction materials using the novel geopolymerization technique. (Xu and van Deventer, 2000, 2002a, 2002b; Pacheco-Torgal et al., 2007, 2008; Zhang et al., 2011; Ahmari et al., 2012) Fly ash is another industrial waste which needs to be carefully impounded because of its potential impact on environment. Many efforts have been tried to utilize fly ash as construction materials because it is a silica/alumina rich aluminosilicate source. In addition, the facts that fly ash is quite reactive to alkali and its particle size is usually very small (< 50 microns) make the specific material an ideal source for the geopolymerization process to make construction materials. Geopolymerization is a process of obtaining a polymeric structure from aluminosilicate by dissolving aluminosilicate sources in a strong alkali (NaOH) solution at an elevated temperature. After being cured at an elevated temperature for a specific time, the geopolymerization product shows a greatly increased compressive strength. Therefore, the product can be used as construction material such as bricks and road pavement. It provides a very promising method to apply aluminosilicate sources such as mine tailings and fly ash as construction materials."

Jan 1, 2016

The Mining Foundation of the Southwest will hold its 15th annual American Mining Hall of Fame Awards banquet on Saturday, Dec. 6,1997 in Tucson, AZ, preceeding the Arizona Conference of SME. The Mining Foundation&apos;s Hall of Fame, located in Tucson, recognizes outstanding contributions to the mining industry by individuals and industry partners. A permanent display of honoree vitae is located at the Arizona Historical Society at 949 E. Second St. in Tucson. Each year, one living award recipient and up to two honorees from mining history are chosen by the Hall of Fame committee and the board of governors of the Mining Foundation. In 1989, the Mining Foundation also initiated a Medal of Merit to recognize outstanding individual technical and professional contributions to the mineral industry. And in 1995, an award was instituted to recognize contributions made by companies and organizations in partnership with the mining industry. This year&apos;s inductee is James R. Moffett, chairman and chief executive officer of Freeport-McMoRan Copper and Gold Inc. He will be present as guest of honor and featured speaker. The Hall of Fame will induct John V. Dorr, metallurgist and chemical engineer. Also inducted will be Frederick L. Ransome, a geologist. Medals of Merit will be awarded to Hugo T. Dummett, senior vice president, Exploration BHP Minerals, and Spencer R. Titley, professor in the Department of Geosciences at the University of Arizona. An Industry Partnership Award will be presented to the Colorado School of Mines for its continued support to the mining industry through education and research. The banquet will be held at the The Westin LaPaloma in Tucson beginning with cocktails at 6:30 p.m. Tickets are available from Clare A. Roscoe, manager, Mining Foundation of the Southwest, telephone 520-577-7519, fax 520-577-7073.

Jan 1, 1997

By Vicki Seppala

Phelps Dodge Mining Company operates some of the world’s largest open pit mines. Safely mining in these deep pits requires the commitment to a proactive integrated slope management process. The slope management process also includes the continued look for improved slope design, construction, and maintenance of slope faces. This paper discusses integration of such technology as electronic programmable detonators, 3D imaging using ground-based LiDAR scans, and reflectorless slope monitoring systems in a slope management program.

Jan 1, 2005

By Robert M. Dreyer

In an industrialized nation, as the process of industrialization continues, the ratio of the value of production of non-metallic to metallic minerals normally increases gradually over a period of years. For example, in the United States, the ratio of the value of production of non-metals to metals now is approximately two-to-one. Those of us who come from California like to think that we inherit the mantle of the old hard-rock miner, but the truth of the matter is that, in California, of the total value of mineral production exclusive of fuels, 97% comes from non-metallic - industrial - minerals. Since the industrial minerals furnish a principal source of raw materials for the construction and chemical processing industries and since these two industries, in industrialized nations, generally increase directly with increasing population, the future of industrial mineral production both in the United States and throughout the world is indeed bright. Because of the importance of industrial mineral production, it often surprises those of us in the industrial mineral industry to find that industrial minerals are poorly understood by many of our colleagues in the mining industry. I think that one reason for this comprehension of the industrial mineral industry is that the education of both geologists and mining engineers still markedly emphasizes exploitation of the metals.

Jan 1, 1964

By Seppo] [Kreula

Outokumpu Oy has acquired considerable experience with on-stream X-ray fluorescence analyzers and with computer control of flotation processes over several years. It became evident at the outset of this work that a reliable and accurate on-stream analyzer was more than a collection of different pieces of hardware linked together. Extensive work was done to develop an integral analyzer system, beginning with process samples through the spectrometer to report typewriters, recorders and the control computer. To date, over ten Courier-300 analyzer systems based on this development have been installed world-wide, several of which provide the key information for successful computer control systems. Computer control of flotation processes has been under development at the Pyhäsalmi concentrator since 1968. Two different control strategies have been implemented. The copper flotation is controlled by means of a mathematical model and economic criteria, whereas the "evolutionary operation principle" is applied to the zinc flotation. The computer control system installed at&apos; the Vuonos-mine has been developed according to the same guidelines. In order to consolidate this wide experience, a flotation computer control system, Proscon-100, was developed by Outokumpu Oy, and the first system was installed at Kotalahti in 1972. In addition to the technological experience, enough information has also been gathered to illustrate the economical, benefits accruing through the use of these advanced tools of automation.

Jan 1, 1973

By A. Cartwright, J. Cardwell

"Complex geology requires innovative approaches to confidently and appropriately model grade and geologic trends. Local Anisotropy Kriging (LAK), by Isaaks and Company, and MineSight® Dynamic Unfolding (MSDU) from Hexagon Mining are advanced interpolation methods designed to best estimate grade along deformed three-dimensional grade trends at sediment-hosted deposits. While LAK works in Euclidean space for the construction of variograms, kriging weight assignment, and non-linear local interpolation search ellipsoids, MSDU is far more dynamic and can utilize a modeled three-dimensional undulating surface representing a folded grade trend to construct the above mentioned. MSDU was implemented at the sediment-hosted, stratabound Tenke-Fungurume mining district and revealed major block-to-block differences in interpolated copper and cobalt grades compared to LAK. INTRODUCTION Grade estimation is the cornerstone of long-range mine planning. Pit designs, metal recovery, mining costs, reserves calculations and reporting are all dependent upon a reliable grade model. If the geology is poorly understood or the interpolation methods and parameters have been haphazardly constructed, then massive financial losses will be the inevitable outcome. Therefore, a properly trained geologist must use all of the appropriate tools available including deposit knowledge and advances in modeling technology to construct the most geostatistically and practically sound long-range block model. Certain deposits, such as the sediment-hosted deposits at Tenke-Fungurume, require an interpolation method that best suites the style of mineralization. In 2014, Hexagon Mining developed a tool in MineSight called dynamic unfolding (MSDU) that has the potential to improve upon previous Euclidean-based interpolation methods. MSDU utilizes the non-stationarity of a folded grade trend to more accurately construct variograms and improve interpolation results based upon a modeled three-dimensional surface. Geology Overview The sediment-hosted Tenke-Fungurume mining district is located in the southeastern part of the Democratic Republic of the Congo (Figure 1). The rocks within the district are primarily dolomites and shales from the lower half of the Roan Supergroup that were mineralized by ascending pregnant copper and cobalt rich brines within a massive sedimentary basin (Cailteux et al., 2005) (Figure 2). These oxidized brines likely found a fluid channel in the porous RSC unit. The surrounding rock units provided a redox boundary for copper and cobalt precipitation along organic rich beds, forming a massive stratabound deposit that was later broken up by several subsequent tectonic events (Dewaele et al., 2006). Layering and Block Orientations To capture the bedding-controlled nature of the Tenke-Fungurume copper and cobalt mineralization, each lithology type must be subdivided into individual layers with a uniform thickness (Figure 3). The thickness of each layer is determined by the user, but should equal the bench height to achieve maximum resolution within each lithology type. Composites are back coded from the model to achieve layer codes that match block locations."

Jan 1, 2016

By J. Y. Hwang

Sands are utilized to make molds for metal castings in the foundry industry. Approximately a half ton of sand is disposed of for each ton of metal cast in this country. In Michigan, annual sand disposal amounts to about one million tons. A process has been developed in this study to reclaim sands from a steel foundry. Physical separations are utilized in conjunction with other operations (such as the removal of binder, metal, spruce, washes, etc.) to yield silica and chromite sands with desirable molding properties. Several different separation methods, including electrostatic, magnetic, and various gravitational approaches have been examined. Experimental results are presented. The applicabilities of these separation methods are discussed.

Jan 1, 1992

By Håkan Stille, Jalaeddin Y. Rafi, Fredrik Johansson

"INTRODUCTIONIn tunneling projects, pre-grouting is performed with the purpose of establishing an impervious zone around the tunnel periphery. This is obtained by reducing the penetrability of the most conductive fractures in the rock mass. The main attention, besides economy of the project, is given to limiting the ingress of water into the tunnel to a certain amount during construction s well as operation period. Failure in pre-grouting process may, according to Bruce (2007), significantly affect the project in terms of safety, performance, cost and time. In this respect, determination of design parameters (pumping pressure, properties of the mix and stop criteria) affects these projects significantly. In current practices, depends on the geological conditions and requirements of the project these parameters differ widely. Weaver (1991) recommends selection of design parameters, specifically grout injection pressures, based on site specific factors and the conditions at each specific hole into which grout is to be injected (grout hole logging and water pressure test data). Houlsby (1990) correlated the allowable grouting pressure to the quality of the rock mass and the rock cover above the grouted fracture. In his methodology, grouting should be continued until the maximum pressure was attained. Later, Lombardi and Deere (1993) introduced the Grout Intensity Number (GIN), which limits the combination of injection pressure and injected grout volume in order to control the energy induced in the fracture i.e. avoid fracture jacking. Even though the GIN method was a step forward in understanding of the mechanism of the fracture deformation, there are ambiguities connected to this methodology, thus determination of the intensity number is challenging (see e.g., Rafi and Stille 2015)a.A main problem when no theoretical solution is practiced is that effects from the chosen injection pressure, such as possible increases of transmissivity and changes in total grouting time, remains hidden in the overall grouting process. The question is if a high or a low pressure should be used to fulfil the requirements of the projects at the lowest possible cost."

Jan 1, 2016

By D. B. Apel

Rock mechanics software plays an important role during the design process of modern underground mines by allowing for verification of the stability of the planned excavations. The paper describes the methodology used to plan and locate the permanent underground openings at McArthur River Mine with the assistance of numerical modeling software.

Jan 1, 2004

By Nopadon Mantajit, Dallas W. Davis, Somsak Potisat, Prasert Kumalachan

For centuries Thailand has been a significant, though primarily unofficial, producer of gold. Panning has been the traditional way of making a living for innumerable villagers during the December to May dry season following the harvest. During this period groups can be seen working the streams, rivers, fields and dry valleys at as many as 90 localities in 28 provinces. Attesting to their efforts are the five and a half ton solid gold Buddha at Wat Trimit and much of the gold jewelry sold in Bangkok. This traditional panning will continue, and probably become more extensive, in harmony with commercial endeavors using modern technology suitable for extraction of gold from types of deposits for which gravity separation would give very low recoveries. Several such deposits have been discovered in the course of geochemical and geological surveys conducted by the Royal Thai Department of Mineral Resources with the object of contributing to early interpretation of the results of a country-wide airborne survey.

Jan 1, 1987

By J. Wesley Atkins

In considering the importance of lease management and administration, I have decided to approach the topic, Lease Default and Eviction: Action or Reaction, as a three phase presentation dealing with mineral lease administration and management, past, present and future. Though the title may border on the dramatic, it illustrates the real consequences of alternative approaches to property management viewed from my experience in the evaluation, development and implementation of a number of such systems and services in my current position as president of Talco Group Corporation. First, though, let&apos;s take a moment and set the stage by giving a few actual examples of why a pragmatic approach is needed in this particular area.

Jan 1, 1983

By Michael H. Leon, John A. Organiscak

Controlling worker dust exposure on longwall mining systems is difficult because the working face area serves as an immediate return during the mining cycle and the amount of airborne dust generated is directly related to production. Since improvements in longwall mining technology have significantly boosted production levels, additional technology is needed to control the airborne respirable dust generated at present and future production levels. One concept to reduce longwall worker&apos;s dust exposure is to maintain two splits of air at the face -- a clean intake split in the workers walkway, and a return (dusty) split over the face conveyor. The U. S. Bureau of Mines has recently investigated a concept to overcome the visibility handicap of face partitions by utilizing a permeable polyester mesh. The mesh material was anticipated to provide adequate air-splitting capabilities as long as the pressure differential between the face and worker walkway was minimal. Initial testing of this concept at the Bureau&apos;s Lake Lynn Laboratory showed that notable reductions could be achieved with a 1/8 in (3.18 mm) and 1/16 in (1.59 mm) mesh opening size. Dust reductions at 100 ft (30.5 m) and 200 ft (61.0 m) downstream of source were 58 and 36 pct, respectively, for the 1/8 in mesh and 79 and 55 pct, respectively for the 1/16 in mesh. Longwall application of the 1/8 in mesh showed similar results to the Lake Lynn Laboratory tests. A flame retardant mesh was used underground with portable lighting mounted on the shearing machine for face side lighting.

Jan 1, 1993

By Adam Graf

Mineral deposits are fundamentally different from most other assets -Every deposit has unique geologic and metallurgical characteristics -Asset (resource) is finite and cannot be truly replaced. -Long timeframe and time-value of reserves -Commodity price volatility (see Torries, 1998)

Jan 1, 2003

By A. Ghosh

Commonly used predictors of ground vibration from blasting, being linear in log-log plot, do not model the underlying physics of wave attenuation. Amplitude of the wave decays with distance due to geometrical spreading and inelastic attenuation producing a nonlinear carve in log-log scale. The nolinear decay of seismic waves has also been observed from non-explosive sources, such as, pile driving, drop hammer, traffic, etc. The improved predictors, by explicitly taking these two mechanisms into consideration, model the data trend extremely well at all distance ranges. Actual field data from different studies have been used to validate the improved models.

Jan 1, 1991

By Ignacio Salazar

Somebody sure gave me the wrong title. I can talk much more freely about the impact of the anti-nuclear movement on the DRILLING industry in New Mexico. In a word, it is being "clobbered." It doesn&apos;t seem like very long ago that my brothers and I were busy trying to find enough new equipment (and trying to talk bankers into lending us enough money) to keep up with drilling work we could get. Seemed like no matter how hard we worked, and how much money we borrowed, we were always one step behind where we wanted to be. We had so many holes to drill that all our crews were working three shifts a day, and over several states. The nation needed energy, and we were ready to help supply it. Exploration and development drilling jobs were all going full-blast. We had trouble keeping up with them. With luck, we figured we&apos;d be able to get all our equipment out of hock before all the necessary uranium mines were developed.

Jan 1, 1979

Lingering effects of the 1990 oil shock that included overbuilding and corporate and individual financial distress caused the Gross Domestic Product to fall slightly to $5.67 billion (US billion = l09). With 254 million people - 697,000 in mining and petroleum - the US has more than 100 million dwelling units and 190 million licensed motor vehicles. New private housing starts fell 15% to one million units. New car production fell 11 % to 5.4 million units. Truck and bus production fell 8% to 3.4 million units. The inflation rate was 3%, while the prime rate of interest was 8.5%. The Producer Price Index (1982 = 100) changed as follows: -fuels and related products and power down 1% to 8l, • metals and metal products down 2% to 120, • chemicals and allied products up 2% to 126, and • non-metallic mineral products up to 2% to 117. Energy Imports of crude and refined petroleum, costing $50 billion, fell 5% to 2.8 billion bbl. Domestic petroleum production rose 1% to 3.6 billion bbl. Petroleum supplied about 39% of US energy, natural gas 24% and coal 22%. The National Energy Strategy was announced in February 1991. Its purpose is to encourage domestic production of fossil fuels and nuclear and renewable energy and to stimulate efficiencies in use. Congress continued to debate the strategy and took no action. Coal production fell 3% to 902 Mt (994 million st). About 60% of that came from surface operations. Seventy-eight percent of the total was used to generate electricity and 3% was coked.

Jan 1, 1992

By Justin Brown, Michael Kobler, Dave Ragland, Bob Shufflebotham

PROJECT OVERVIEW As the sun-bronzed San Diego students strolled casually to class, mining crews from Atkinson Construction were working only 9 meters below the surface. The330 meter long, 11.3 meter diameter squat ellipse NATM tunnel is part of the9.3 kilometer Mission Valley East Extension Light Rail Transit (MVE-LRT) being constructed for the San Diego Metropolitan Transit Development Board (MTDB). The SDSU segment of the MVE-LRT was awarded to the Clark Construction Group, the parent company of Atkinson Construction for $82.7 million. URS CORP was the prime designer and Hatch Mott MacDonald performed the NATM tunnel design. The construction managers were Washington Infrastructure Services with Underground Construction Managers, EPC Consultants, and ILF Consultants. A NATM tunnel design was chosen as the most cost-effective way to minimize disruption of the university activities. The tunnel passes close to several buildings and directly below access roads, tennis courts and a baseball field. The NATM method of conventional mining uses shotcrete for ground support often reinforced with steel orplastic fibers, welded wire mesh and lattice girders. The tunnel runs from a cut and cover box up a 4.2% grade in a 217 meter radius left-hand curve with several spirals and ends at the underground station 330 meters away. The depth of cover varies from 16 meters near the west portal to nine meters at the station. The design called for a two-pass system with a primary lining of 300 mm shotcrete with lattice girders at 1 m centers and two layers of welded wire mesh. The lattice girders are used primarily for profile control and are not considered a structural element. The top heading was designed to be excavated in one of three excavation sequences depending on ground conditions and depth of cover. In sequence one excavation, the top heading is excavated in two halves with a one-meter separation. In sequence two excavation, a side gallery is advanced 8 or more meters ahead of the

Jan 1, 2003

By D. J. Boron, R. Kollrack

Introduction The US has the largest total (364 Gt, or 401 billion st) and recoverable (182 Gt, or 201 billion st) coal reserves in the world (Steam/Its Generation and Use, 1978). However, progressive coal use in this country has been hampered by environmental constraints, such as restrictions on sulfur dioxide, nitrogen oxides, and particulate emissions. Since the promulgation of the Environmental Protection Agency (EPA) New Source Performance Standards (NSPS), it has become apparent that all US coals will require sulfur removal to comply with the new sulfur dioxide emission levels. If more stringent emission standards are imposed, through pending acid rain legislation or amendments to the Clean Air Act, it is likely that the coal industry, and the industrial and utility sectors will look increasingly toward the development of new and advanced coal cleaning technologies to continue and promote the use of coal. Table 1 summarizes the EPA NSPS for sulfur dioxide emissions. Fortunately, the basis for determining sulfur dioxide removal is the Btu and total sulfur content of the run-of-mine coal. Thus, credit is given for any sulfur removed before combustion, e.g., through physical coal cleaning. Unfortunately, physical coal cleaning alone may be unable to produce a compliance coal with respect to the EPA NSPS. Therefore, all industrial and utility coal-fired boilers will require post combustion gas cleanup, e.g., flue gas desulfurization (FGD), to comply with the new regulations. Table 1 - EPA NSPS for SO2 Emission Category SO2 Content of ROM Coal SO2 Reduction Required 1 0-2 Ib/M Btu 70 2 2-6 Ib/M Btu To 0.6 Ib/M Btu (70% to 90%) 3 6-12 Ib/M Btu 90% 4 12 Ib/M Btu To 1.2 Ib/M Btu Alternatives to post combustion gas cleanup, such as staged combustion, lime and coal injection, fluidized-bed combustion, and chemical coal cleaning, are currently under development. Of these, chemical coal cleaning offers the advantages of providing (1) high quality fuel for combustion (low sulfur and ash, high Btu, and attenuated product variability); (2) a solid fuel product for use in retrofitted gas and oil boilers; and (3) a solid fuel product with multiple end uses, e.g., internal combustion engines, carbon electrodes, coke, or chemical feedstock. Gravimelt process In the Gravimelt process, 1.4 mm x 0 (14 mesh x 0), physically beneficiated coal of about 5% moisture is fed into a 3401 to 3901 C (644 ° to 734 ° F) molten bath of sodium hydroxide and potassium hydroxide. Organic and pyritic sulfur and most of the mineral matter in coal react with and are dissolved in a molten mixture of potassium hydroxide and sodium hydroxide. The reacted coal sulfur is converted to alkali sulfides and polysulfides, whereas the mineral matter is apparently converted to alkali-aluminum silicates and other byproducts that are water and acid soluble. Coal residence time is 60 to 240 minutes. The sodium hydroxide to potassium hydroxide ratio is about 9:1. The total hydroxide-to-coal ratio is no less than 10:1. The specific gravity of the caustic melt is about 1.8 g/cm3 . Thus, coal is buoyant in the bath, and insoluble mineral matter with density greater than 1.8 g/cm3 would sink. Reacted coal is first water-washed with an equal weight volume of water in a countercurrent mode of operation. The coal is filtered and the filtrate sent for regeneration. The coal is then acid-washed in 10% sulfuric acid. The acid-water/coal mixture is filtered to recover the final coal product, and the filtrate treated with lime to precipitate dissolved mineral matter. The precipitate is filtered from the mixture and discarded. The water is recycled to the plant. Filtrate from water-washing is treated to remove sodium sulfide. The sodium sulfide is chemically treated to produce hydrogen sulfide, calcium car¬bonate, sodium hydroxide, and other products. The hydrogen sulfide is treated to produce sulfuric acid for the acid-washing step. The calcium carbonate is treated further or discarded, and the sodium hydroxide is concentrated by evaporation and recycled to the reactor. The Gravimelt process is currently at the bench-scale stage of development. A 0.9-kg (2-lb) continuous reactor is in operation with a continuous water- and acid-washing section adjacent. The regeneration section is not developed to a meaningful extent, although key reactions have been tested in the laboratory. Process conditions, product recovery efficiencies, etc., however, have not been determined adequately and continuous regeneration operation has not been attempted. Work is now in progress to develop each section to a continuous bench-scale operation in processing coal at 9.1 kg/h (20 lb per hr). Microwave process The carbon and hydrogen in coal are relatively transparent to microwave radiation. However, water, caustic, pyrite, and other mineral matter components are strong conductors of microwave radiation energy at the proper frequency. As a result, selective heating of the noncarbonaceous materials occurs that enables the chemical reaction of sulfur and ash with caustic. Although very high temperatures may result from

Jan 1, 1987