Search Documents

By M. S. Klima

Tests were conducted to investigate the potential for recovering anthracite from preparation plant tailings. Samples were collected from tailings streams or slurry ponds of several anthracite cleaning plants. A washability analysis was conducted on each sample. The use of gravity-and surface-based cleaning processes for treating the 28x200 mesh tailings material was examined. Simulations were performed for various cyclone staging arrangements using published partition data for both water-only and dense-medium cyclones. Froth flotation testing was done on both precleaned anthracite and tailings material. Grade-yield curves were determined for various conditions.

Jan 1, 1995

By B. T. Field

Pyroprocessing systems range from low temperature dryers to high temperature reactors. The materials and process requirements cover a broad spectrum. It is not the intent of this paper to do a detailed examination of individual processes and equipment, since that can be found in a multitude of other sources; rather it is the intent of this paper to examine the key process variables and offer empirical guidelines to assist in a user?s overall evaluation.

Jan 1, 1998

By J. R. Patts, J. P. Rider, J. A. Organiscak, A. B. Cecala

"NIOSH recently completed a 15-month study at an underground limestone mine crusher booth which evaluated three research parameters: (1) the effectiveness of a single-filter filtration and pressurization system for improving the air quality inside the operator booth, (2) comparing the effectiveness of ? > 99 and ? > 95 experimental prototype filters in the system, and (3) evaluating the use of three different pressure monitoring devices to determine the performance of the filtration and pressurization system over time. The protection factor was quantified monthly using particle counters in the respirable dust range (0.3–10 µm), and gravimetric dust samples were gathered at the beginning and end of the overall study. Under static conditions and after outlier removal, the single-filter filtration unit installed offered a protection factor between 8 and 216, depending on the filter type and loading condition. The particle counting analysis shows that the ? > 95 filter offers a protection factor greater than 4-times that of the ? > 99 filter when evaluated over 60 minutes. The booth pressure monitors provided data that proved to be a valid indicator of system performance over time. INTRODUCTION Designed and installed correctly, enclosed cabs, operator booths and control rooms offer mine workers protection from physical hazards, such as flying rock, debris, and noise, as well as a more comfortable environment in regards to temperature and humidity [1]. But while it may be easier to quantify whether the A/C unit is working (measuring the temperature) or observe whether the cab offers protection from flying debris, it can be somewhat more difficult to quantify its performance in reducing respirable dust hazards. For over 15 years, NIOSH has been conducting applied research to improve the air quality inside of enclosed cabs of mobile equipment [2-5]. This work has led to the identification and mathematical modeling of enclosed cab filtration systems [6]. The same principles that govern the performance of filtration systems on mobile equipment are applicable to stationary enclosures such as operator booths and control rooms [1, 7]. Stationary enclosures are similar to enclosed cabs; however, the volume of the work area can be significantly larger. In addition, workers who perform their duties in stationary enclosures tend to stay within the room for a greater percentage of the day, as opposed to workers on mobile equipment who may enter and exit frequently. Structural integrity can be easier to maintain as well, as there is typically less vibration and stress placed on these compartments as compared to mobile equipment. In addition to offering protection from dust and flying debris, enclosures must ensure that workers have a healthy supply of fresh air to avoid elevated levels of CO2, which are known to cause headache and dizziness, impairing cognitive function. The American Society of Heating, Refrigerating and Air-Conditioning Engineers (ASHRAE) states that enclosures should have no more than 1,100 ppm of CO2 when outside levels are 400 ppm [8]. In addition, the American Society of Agricultural and Biological Engineering (ASABE) recommends a minimum airflow for enclosed cabs of at least 42.5 m3/hr (25.0 cfm) per person [9] to ensure an acceptable level of CO2."

Jan 1, 2017

By Donald V. Fites

The evolution of open-pit mining has been rapid during the last two decades. The development of larger, more productive and efficient equipment has been one of the key factors in this open-pit advancement. Selection of the proper equipment and its correct usage is paramount to successful operation while maximizing return on investment. The quantity of material being moved prior to mining the saleable product is increasing at a significant rate. For example, at a southwestern copper mine more than two hundred million tons of over- burden have been removed prior to exposing an ore which contains less than 1% copper. A recent survey of twenty-three Western Hemisphere copper mines reveals the average strippingratio was 2.2:l with a range of 0.9-8.5:l. In the face of increased mineral demand, the resulting technological developments and rising overburden to ore ratios, many open-pit mines now use totally different concepts for the removal of ore and overburden. An increasing number of these concepts now being installed include wheel tractor scrapers as a major part of the material handling system for unconsolidated overburden removal. To say scrapers move only unconsolidated overburden is incorrect. On the contrary, ripped phosphate rock, copper ore, iron ore, and moderately consolidated overburden are also being moved by scrapers in various areas of the world. As reported in the Minerals Year- book, however, about one-half of the material moved in metal and non-metal mines is never drilled and blasted or broken by other means. We will, therefore, in this paper, concentrate on the role of wheel tractor scrapers in unconsolidated overburden; the area of greatest usage.

Jan 1, 1969

By T. P. Weldum, B. J. Mahoski, R. S. Rasmussen

A case study of a systematic approach to grinding circuit steady-state optimization is presented. After an overall review of the flow-sheet, two operating circuits were prepared for detailed testing. Functional performance analysis was chosen as the primary modeling system, and, on this basis, a quality-assurance program for data gathering was implemented. A number of circuit-design and operating variables were investigated. Statistical analysis of plant-test results revealed relationships previously unquantifiable by any other modeling technique. Improvements in the classification system and in mill grinding efficiencies were demonstrated. As a result, there was significant energy cost savings.

Jan 1, 2000

By Frank Pollard

The Australian coal industry over recent years has experienced the situation whereby exploration and mine development are moving into geographical areas where the coal seams have never been mined to any extent in the past, if at all, and particularly where there is no history of experience in preparation of these seams. Additionally, the demands have been such that the development of a mine up to production stage should proceed with minimum delay. This is a situation which is of some importance and concern, in view of the coal quality requirements now experienced within world markets which can only be met, in most cases, by careful preparation. Costs are such that the preparation plant should operate as required by the situation and with maximum efficiency, which means that laboratoty information of breakage and washability characteristics which are required for preparation plant design should be accurate and available as soon as possible, even to a certain extent during the progress of the exploration.

Jan 1, 1981

By G. Kraemer, J. A. Le Gac, P. R. ZETTWOOG

I. INTRODUCTION During the course of our activities in assisting mining companies, we have had access to the monitoring results for personnel from a large number of uranium mines. The results differ greatly from one mine to another. One of our objectives has been to discover the origin of these differences. It is evident that they are largely due to variations in the geological context, to mining methods, and to the organization of the work ; but we also found that the rigor with which measures are implemented to prevent the personnel from being exposed to radiations is also a cause. In order to advise mining operators effectively, we have asked ourselves the following question Given the dosimetric results of a mining site, how can it be known - if occupational exposure has been reduced to the lowest possible level (dose optimization principle recommended by the ICRP) ; - if the exposures were justified, which would not necessarily be the case following a questionable choice of the mining method, for instance, or a lack of efficiency in the maintenance and repairs of ventilation apparatus or even an excess of radiation protection. It is necessary to establish some criteria, while taking into consideration the specific conditions for each mine, in order to determine whether a mining company is adequately implementing radiation protection procedures. This need led us to attempt a modelization of the occupational exposures of uranium miners ; the preliminary phase is presented here. Although voluntarily still very basic, this model makes it possible to demonstrate the role of certain dynamic or passive variables. Moreover, the model presents the concept of specific irradiation of a mining site equal to the collective dose received per ton of uranium metal supplied to the uranium mill. The specific irradiation can therefore be used to indicate the effectiveness of radiation protection procedures at a given mining site. This model can be used for - previsional exposure studies based on the use of data gathered at each site, making it possible to compare various work methods and to determine prevention means ; - qualification of "radiation protection" procedures at a mining site ; - detection of unjustified exposures ; - research of ways to reduce inevitable exposures. 2. DETRIMENT TO BE ASSOCIATED WITH A GIVEN EXPOSURE DISTRIBUTION Respecting exposure limits ensures that delayed stochastic effects are the only health risks to workers. If the hypothesis of linearity in the dose-effect relationship is applied, the detriment to a group of workers is proportional to the sum of exposure for all the workers, or the collective exposure usually expressed as man x rem. On this point the linearity of effects hypothesis makes it possible to consider that two different standard deviation distributions having the same mean value are equivalent. It would be possible, then, to reduce the standard deviation by changing the distribution of workers at the various working places without changing the mean exposure value. In other words, without taking into consideration the practical implications, individual limits can be respected by rotating the personnel or by reducing the individual working period which would be compensated by increasing the number of workers. The collective dose would remain the same, which would justify the use of the concept of collective exposure. 3. "RADIATION PROTECTION" QUALITY INDEX AT VARIOUS MINING SITES Each mining site is responsible for its own collective dose, but it is also responsible for producing a certain amount of uranium metal in the ore sent to the uranium mill. These two quantities must be brought together in order to establish the "radiation protection" quality index of a mining site. This quality index, called-specific irradiation (Ir) is expressed in rem.ton -1 for external irradiation, in mJoule.ton-1 for inhaled [a]-energy, and in Ci.ton -1 for inhaled radon *. The specific irradiation represents the health hazard which must be associated to the extraction of one ton of uranium metal. Figures la and lb present a system of coordinates for which the axis of the abscisses is graduated in tons of U metal and the axis of the ordinates is graduated in units of collective exposures. In the EEC, the regulation is based on the measurement of the amounts of radon 222 inhaled.

Jan 1, 1981

By Kenneth R. Dickson, I. Michael Gowring

This paper describes the underground work associated with the North Fork Stanislaus River Hydroelectric Development currently being constructed by Sierra Constructors for the Calaveras County Water District in California under a turnkey contract. Sierra Constructors is a joint venture of the Guy F. Atkinson Construction Company (sponsor) of South San Francisco, and the Harrison Western Corporation of Denver. Notable features of this project include the exceptionally high performance achieved by the 5.5m diameter Robbins tunneling machine and the 675m deep shaft pilot hole which was successfully realigned using oilfield directional drilling techniques. Other features include 3.7m and 4.3m diameter machine-excavated tunnels and various conventionally excavated tunnels constructed over a wide geographical area and diverse climatic conditions.

Jan 1, 1987

By W. Z. “Ben” Wu

The investigation provides a method of efficiency evaluation among several kinds of tools employed to cut different types of rocks. A ballistic test stand incorporated with a modified Hopkinson bar was used to simulate a percussive drilling tool. An Apple IIe microcomputer was employed for high speed data acquisition and numerical analysis. A newly developed method for remote monitoring the rock-tool interaction, including contact force, bit penetration and energy transmission,is presented in the paper. Theoretical predictions and experimental results appear in faily good agreement

Jan 1, 1986

By Alf Thidemann, Per Marius Nilsen

Tunnelling with hydraulic drills has been a success in Norway. In the fall of 1976 excavation of tunnels for the development of the Aabjoera scheme was started. Two and a half years later a total of 25 kilometers of tunnels are completed. During the most busy period 5 rigs with hydraulic drills were in operation. GENERAL INFORMATION. Aabjoera Hydro Electric Plant is located in the central part of Norway (Fig. 1). The scheme covers a mountaineous area between the Tosen Fiord and the valley of Namdalen. Water from the area of precipitation is transferred through 5 tunnels to the main reservoir. From here the water is conducted via a 10 km long, unlined supply tunnel down to the Kolsvik power station. The power station is situated underground with a short tailrace tunnel out in the fiord. Average head of water is 507 m. The Aabjoera plant is jointly owned by Helgeland Kraftlag A/S, 8650 Mosjøen and Nord-Trøndelag Elektrisitetsverk, 7700 Steinkjer. The Civil Engineering Division of the latter company has acted as Consulting Engineers for the scheme. General contractors for the whole scheme has been Ing. F. Selmer A/S, Box 6035, Etterstad, Oslo 6.

Jan 1, 1979

By Donald E. Hendrickson

A new prinicple of side dumping front end loading for underground mucking machines has completely changed the concept of underground loading and haulage equipment arrangement both in production and development work loading. Versatility and adaptability of this type of machine permits combinations with a broad range of haulage means not possible with -conventional overhead loaders. Steel "armored" conveyors serving this type of loader are replacing conventional rail mounted car haulage to give a continuous loading operation and effect important economics of reduced manpower, faster loading rates and fewer working areas for a required production. First used in Germany this easy to control and highly efficient means of placing rock from the muck pile on or into haulage means has advanced the art of underground rock loading more in the past three years than any other advancement since the first successful small crawler mounted air powered loader was introduced in 1954. Bucket type loaders with a relative new side dump principle are gaining in popularity for underground loading. They are replacing conventional overhead loaders in present applications and becoming first choice in new ones. Primarily for hard rock development and production loading they are also widely used in production loading of coal and other soft materials. This discussion briefly traces the historical development of hard rock underground loaders to the new side dump type and its present population. In more detail various applications, loading techniques and the advantages of operation, production and economy with the side dumper in hard rock loading will be dealt with.

Jan 1, 1966

By R. Y. Wan, J. D. Miller, P. L. Sibrell

Three different refractory carbonaceous gold ores from the Carlin operation in northeastern Nevada were investigated to characterize the effect of passivation treatments on the nature of the carbonaceous material. The carbonaceous material was chemically isolated from the ores and passivated residues, and examined by FTIR spectroscopy, elemental analysis, and gold adsorption capacity. The main component of the carbonaceous material in these ores was found to be a naturally occurring activated carbon-type compound. Hydro-carbons were detected on rare occasions, but no evidence was seen for humic acids. Ore samples were passivated by autoclaving, or by treatment with sodium hypochlorite or gaseous chlorine. In some of the passivation tests, a new peak was observed in the IR spectra of the isolated carbonaceous material, that was due to carbonyl functionalities. However, all of the passivation treatments tested decreased preg robbing significantly. This suggested that the appearance of the carbonyl peak was due to the severity of the conditions during passivation, rather than the method used.

Jan 1, 1990

By T. M. Dyhr, T. E. Wilson

Although environmental management costs during mine operation depend on the size, type, climatic and geochemical conditions of operation, general cost categories are identified and mean values, as a percentage of total operating cost, are determined for coal and non-coal surface and underground mines (medium-size) with on-site beneficiation and tailings disposal facilities. Cost trends are charted from 1963 through the present.

Jan 1, 2004

By James S. Scott

Effluents discharged from gold mills, and more recently from heap leaching operations, pose significant hazards to the environment if not properly managed prior to discharge. This paper describes the nature of wastewaters which must be treated, the treatment processes being applied in Canada and the capabilities of these methods in removing cyanide and metals. As a result of past practice the most common method of reducing cyanide in gold mill effluents remains that of natural degradation in tailings ponds. This method has proven capable of producing high quality effluents where large ponds and sufficiently long water retention times can be provided, but at many mines this has not been the case. Since 1981, as a result of these limitations there has been a strong move in Canada to chemically-based effluent treatment plants, particularly as additional processes became available. Canadian gold mills have become leaders in the use of chemical processes to remove cyanide, in terms of the variety of such processes in operation (five in total), the number of plant installations and the number of processes developed in this country. The hydrogen peroxide and Inco SO2-air processes, in that order, are being applied most widely. Alkaline chlorination, the initial process to be used fairly extensively has been almost totally replaced by the two methods mentioned above. Since a number of effective methods are now available for the treatment of gold mill effluents, the selection of a process for application at a specific mill requires careful consideration of:

Jan 1, 1987

By Richard L. Ash

Usually stresses generated by explosive charges during blasting are considered to propagate through materials in a spherical manner. Although conical stress-waves had been suggested by a few investigators they have never been clearly defined or critically observed. An experimental technique using models and lengths of Mild Detonating Fuse was developed to produce conical stress-waves and study their effects. Several materials with different properties were tested to compare the influence of those properties on wave shape and crater formation. The investigations showed that whenever column charges were end-initiated, conical stress-forms were produced if the explosive's velocity exceeded the energy propagation velocity of the surrounding material. The stress-cone angle significantly affected fragment size and shape as well as the geometry of craters produced.

Jan 1, 1967

By R. J. Weege

Conventional underground mapping methods and diamond drilling are being applied in a study to determine the nature of the copper ore occurrences near the footwall of the Osceola lava flow top, commonly referred to as the Osceola Amygdaloid. Our work to date suggests that structures formed by relatively impermeable barriers, created by flowage and injection of still-molten lava from the interior of the flow into the solidified, brecciated crust, acted as the ore receptacles. Ascending hydrothermal fluids traveling near the footwall contact were trapped and confined in these barriers which retarded the direct upward movement of the ore fluids and caused deposition of copper. Oreshoots located near the footwall appear to have been formed spatially' independently from the hanging-wall oreshoots by fluids traveling simultaneously, but along different channelways. The barrier concept as advanced by earlier writers to explain the concentration of the ore-bearing, fluids into broad shoots con¬stituting entire ore bodies is found to be equally as applicable for the localization of smaller oreshoots within the Osceola ore body.

Jan 1, 1962

By J. D. Miller, C. L. Lin

The appropriate software and hardware necessary to adapt an X-ray CT analyzer for the determination of coal washability was developed and successfully tested for well-characterized samples under laboratory conditions. Evaluation of the CT-based analyzer under simulated on-line conditions is also presented to verify the on-line capabilities of the newly developed X-ray CT analyzer for the control of coarse coal cleaning circuits. The investigation shows that the data obtained from CT washability analyses compare favorably with experimental sink float data. Further, image frequency was considered to evaluate the CT-Based coal washability analyzer for simulated on-line conditions. Specifically, the number of observations (image spacing) needed for accurate sampling and the total time required to perform the calculations for a representative data set were determined. Key words: Coal washability, Computer simulation, X-ray CT analysis

Jan 1, 2003

By V. Iordachita

In the beginning of the third millennium, the world mining industry has to cope with many challenges; the continuous need for mineral resource deposits and the mostly unsolved economic efforts should be accompanied with ecologic measures mankind has to take in order to avoid self-destruction. The present paper analyses the possibilities of using underground mining spaces in Romania for storing dangerous waste and suggests viable solutions. The characteristics of dangerous wastes and their disposal in suitable underground spaces are analyzed. Also, some methods for deactivating dangerous solid wastes as well as the importance of monitoring underground spaces in order to eliminate environmental impact risks are presented.

Jan 1, 2008

By Edward I. Erlich

1984 saw the 30th anniversary of a momentous event in Soviet geology-the discovery of kimberlites in Siberia, an event that vaulted the Soviet Union to second rank among the world's producers of both gem and industrial diamonds. There are many legends associated with this story, legends about those who predicted the discovery and those who achieved it in the field. The story told here unfolded during the field campaigns of the 1940s through 1960s, as witnessed by the authors and their companies of an earlier generation. This story illustrates science, chance, and human emotions at work, resulting in a blend of conviction, courage, bureaucratic sniping, and competition for glory. At the same time, it is an illustration of the workings of the Soviet exploration system. In a broader sense, it is the realization of the Russian image-boundless natural wealth, indomitable ingenuity, and the rigid political economic system that permeates the Russian landscape as well as the people. Most accounts of the Siberian diamond saga begin with statements such as, "This discovery confirmed the predictions of...", or "It was a result of predictions of one of the greatest Soviet geologists, Academician V.S. Sobelov...". These are only part of the truth. It had become apparent even in the 1930s that the Siberian Platform contained one of the Earth's greatest Basaltic provinces, described in a monograph by Sobolev...; and at the end of the thirties, G.G. Moor of the Institute of Arctic Geology found alnoites, similar in many ways to kimberlites. At the same time, the famous polar geologist, N.N. Urvantsev found other kimberlite like rocks in the southern Taymir Peninsula, adjacent to the Siberian Platform. In publications describing these rocks, Moor and Urvantsev mentioned for the first time the possibility of finding diamondiferous kimberlites similar to those in South Africa. Unfortunately, Urvantsev spent little time in the field between terms in concentration camps. Moor was considered by his superiors to be no more than a good descriptive petrographer; they suggested to him that his conclusions should be backed up by more highly regarded specialists. Thereupon, Moor asked Sobolev to coauthor a paper with him and this became the widely quoted prediction about diamonds in Siberia. Another early paper should also be mentioned, an unpublished paper found by M.I. Rabkin in the geological archives of the Norilsk Metallurgical Plant, written by Yu. M. Sheinmann when he worked in the concentration camp there in the late forties. This report placed the probable location of yet-to-be-discovered kimberlites within less than 100 km of their correct location.

Jan 1, 1990

By C. R. Bennett

A copper heap leach model, employing leading edge computational fluid dynamics (CFD) technology, is applied to the Zaldivar heap leach operation in Chile in order to explore and analyze the possible impact of operational changes. The effect of changes to the heap operation on copper recovery has been previously investigated and reported by the Zaldivar operation. This paper examines the extent to which a comprehensive heap leach model supports the analysis and conclusions of the published work. The heap is a complex multi-phase process, consisting of a solid static porous media with complex fluid flow, gas and liquid phases, competing solid-liquid reactions, dissolution of minerals and transport through the heap. The model accounts for the physical and chemical features of the heap, including transport and reactions kinetics for the important copper and iron sulfide minerals, ferrous oxidation, bacterial effects, thermal energy, acid and sulfate balances. The model was calibrated to published data on the ore body and employed to analyze the impact of a number of operational changes, including solution flow rate, acidity, lift height, crush size and head grade.

Jan 1, 2012