Search Documents

By R. V. Ramani, C. J. Bise

INTRODUCTION Classification of coal seams as thin, medium, and thick is both subjective and relative and is more a reflection of the statistical mode of the thicknesses en- countered in a mining region. A geological factor more precisely understood as defined than thickness is the inclination of the seams to the horizontal, commonly referred to as the pitch or the dip of the seam. Thick and steeply pitching seams present far more challenges to the ingenuity of the mining men to devise methods for their extraction than the thick and less steeply inclined ones. In a marginal case, where a thick coal seam may be minable by surface or underground methods, the decision bears a close relationship to the technological developments in the mining scene. Near surface thick coal seams are a special gift of nature and are not as wide- spread as the ones that call for the application of under- ground methods. Recent advancements in surface mining equipment have made it possible to surface mine to great depths. Stripping ratios of 30: 1 (cu yd of over- burden removed per ton of coal) have been achieved. The extraction of thick seams which preclude the use of surface methods is the concern of this chapter. Specifically, the objective here is to outline the special technological factors in underground mining of thick coal seams and to illustrate through several case histories the methods that are practiced in the North American continent. For the purposes of this chapter, a thick seam is defined as one which is not readily minable with currently available equipment without modifications to the extraction method or the equipment. At the present time, a thickness of 4.8 m (16 ft) can be considered as the lower limit, although developments in equipment and methods can be expected to push this limit upwards. The data for the case histories were collected from two extended mine visits in 1975 and 1978, and from other published accounts of the mines visited. Reference is drawn particularly to reports by Bise, Ramani, and Stefanko (1976) and Rarnani and Kenzy (1979). THICK SEAM MINING METHODS The various methods of mining thick seams can generally be grouped into three major categories: full face methods, where the entire thickness of the seam is re- covered in a single pass; slicing methods, where the seam is extracted to its full thickness by horizontal or inclined slices either in an ascending or descending order; and caving methods, where the seam is undercut and the en- tire coal seam is recovered by caving the top coal into the excavated cut, or some variations of the basic sub- level caving method. As shown in Table 1, in each of these methods, the coal is removed by either room-and-pillar or longwall methods. Hydraulic mining and transport of the coal in open flumes or in pipelines are also practiced. Addition- ally, the void created by the removal of coal may be filled with a packing material (stowing) except in the caving methods. The pitch (dip) of the seam, particularly when it is greater than 0.26 rad (150), imposes severe operational limitations on mobile equipment. A more detailed general discussion of the methods can be found in Bise et al. (1976) and Vorobjev and Deshmukh (1964). Specific discussion on the many variations of the three basic methods can be found in the papers presented at the international symposia that were held in

Jan 1, 1982

By W. C. Meyer

The concept of using powdered coal-in-oil-mixtures (COM) as a composite fuel to conserve oil resources and relieve import supply problems is being vigorously promoted by the Department of Energy via the sponsoring of various demonstration units (1). The idea of COM as a useful alternative fuel has been explored on and off for over 100 years (2). The approach must be capable of grinding, mixing, storing, and combusting COM with presumably only minor equipment changes on oil-fired boilers. DOE estimates that 56 000 m3 of oil (350 000 barrels) could be spared daily if a 50-50 COM was used to generate electricity. Of course, the ability of COM suppliers to prepare and deliver a stable suspension of COM at reasonable economic costs must be achieved if the concept is to be successful. This report reviews the various methods used to attain stable coal-oil mixtures. Various physical-chemical principles associated with each method of stabilization are also discussed.

Jan 1, 1981

By K. A. Eriksson

Over 25 years ago, SKEGA pioneered the use of rubber linings in grinding mills and rubber is today widely accepted and almost standard material chosen for Regrind -and Secondary Mills. There are, however, only a few Primary Mills in operation with "solid" rubber linings because available materials and designs are often not cost efficient in comparison with steel alloys on a cost per ton basis and/or downtime for liner replacement would be too high.

Jan 1, 1988

By Jeroen van Eldert, Daniel Johansson, Henrik Ittner, Håkan Schunnesson

"Numerous aspects of underground construction, from structural stability to construction costs, depended on the tunnel quality, including blast damage and the Excavation Damage Zone. Accurately quantifying the extent and severity of damaged rock is a problem. Recent technical developments in the field of Measurement While Drilling (MWD), including software for on-board logging and on-site analysis, have shown potential for rock-mass characterization. Ground Penetrating Radar (GPR) and P-wave velocity measurement have also improved and show similar potential. This paper explores the use of MWD, GPR and P-wave velocity measurements and uses them in techniques for excavation damage characterization and prediction. The paper is based on data collected from a small underground waste-collection site in central Stockholm, Sweden. The data is correlated against rock-mass characteristics and their responses are evaluated. Results indicate potential for excavation damage characterization for all tested techniques, which could minimize blasting damage and improve the over-all tunnel quality. 1 INTRODUCTION During underground excavation the rock mass is influenced in many ways. The Excavation Damage Zone (EDZ) is a result of these influences. The EDZ can be defined by an irreversible change in rock mass properties, for example increased permeability. EDZ is influenced by the excavation method, the rock mass properties and the in-situ stresses in the area of the tunneling. Since the 1990s research has been done on the EDZ by Emsley et al. (1997), Christiansson et al. (2005), Olsson et al. (2009), Ouchterlony et al. (2009), Ittner et al. (2014), and Siren et al. (2015). Based on past literature the EDZ have in this paper been separated in the following subzones: 1. Failure Zone or over-break is the area outside the planned tunnel profile, including the Look-Out and hole deviation. This zone consists of fracture networks (both natural and blasting-induced), that caused rock fall-outs. The extent of the over-break can be determined by volumetric scanning and photogrammetry and the half cast factor can be used as a damage indicator. 2. The Damaged Zone is split into three parts and but the quantity and depth of damage is difficult to measure. Although it can be visualized by sawing of rock slices in the tunnel wall (Olsson et al. 2009), diamond coring (DC) or P-wave velocity reduction (Jern 2001): a. Inner Damage Zone (Crush Zone): It is located directly around the drill hole, and is caused by the shock-wave energy of the detonation. The micro fractures in the Crush Zone produce a white-wash (rock dust) in the half cast. b. Transition Zone: This zone consists of micro fractures that connect and form macro fractures, both radially and parallel to the tunnel wall. The macro fractures are caused by the gas expansion during the detonation of the explosive; it increases the pressure in the (micro) fractures and creates the macro fractures. Seismic reflection, rock slicing and core drilling can be used for the examination. c. Progressing Zone: In this zone the existing radial fractures propagate due to the increase gas pressure inside these macro fractures. Examination methods are seismic reflection, rock slicing and core drilling. In addition, the Peak Particle Velocity (vibrations) could be used to estimate the depth (Tesarik et al. 2011)."

Jan 1, 2016

By V. Rastogi

Acid rock drainage is the result of exposure of sulfidic materials, such as pyrites and sulfidic ores, to air and water. The oxidation of these sulfides is catalyzed by more than a million times by the bacteria Thiobacillus jerrooxidans and close families. Inhibition of these bacteria can mitigate 98% or more of the acid loading generated. This can be achieved by the use of certain surfactants that are selectively bactericidal to the lithotropic acidophilic bacteria. Bactericides are used in two ways. As periodic or continuous treatments for prevention of acidification of material actively handled and moved, and in controlled release form for reclamation where treatment sets up a change in site microbiology to replace Thiobacillus jerrooxidans with heterotrophic bacteria and creates a stable site without need for further treatments. Use of bactericides begins with laboratory testing of the site material to qualify the site for bactericide treatment and dosage determination. Site specific treatments are designed for active sites and reclamation. Once acid production is controlled, solubilization of metals is correspondingly reduced. Results and economics of use from active and reclamation sites are presented.

Jan 1, 1995

By S. J. Ristorcelli

Historically, geologic data has not been adequately considered in resource estimation. More recently, with the use of computers and sophisticated estimation algorithms and geostatistical justifications, geology has been downplayed further. Many reasons are given for not using geology including cost, time and irrelevance. None are valid. Boundaries defining mineral domains should be used in computer-generated resource estimates. Selected case histories show how the failure to honor geology has caused discrepancies in resource estimates of actual in-place resources. After-the-fact differences have included decreases in tonnage of up to 50% and increases up to 300%; partial to complete recategorization of material; and 50% decreases in grade. The costs of gathering and using geology are trivial compared to the potential consequences.

Jan 1, 1994

By E. Jong, E. Watkins

"The application of passive tracer gas sources in underground mines is particularly useful for long-term tracer gas studies, as well as for studies in permissible areas of underground coal mines. The use of passive perfluoromethylcyclohexane (PMCH) sources have previously been demonstrated in mines, but this new work details the development and testing of multiple, distinct tracer compounds that can be used in passive sources. A description of their potential application in mine ventilation systems is also provided. Three tracer compounds are detailed, which are PMCH, PECH and PMCP. The release rates of these tracers were examined over a 180 day period at multiple temperatures. The advantages and disadvantages of these sources are presented, along with potential applications in understanding complicated ventilation circuits, flow through gob, and leakage. INTRODUCTION The use tracer gases for ventilation applications is an established practice, with various research projects being perform with Sulfur Hexafluoride (????6) in the past. Perfluorocarbon tracers (PFTs) however are relatively new compared to ????6, which is proven to be useful in ventilation and air modeling experiments along with other PFTs (Watson, Wilke, Dietz, Heiser, & Kalb, 2007). These liquid tracers are characterized by low background presence in air, inert behavior with other gases, high detectability with a gas chromatograph and low toxicity. A design was proposed called a permeation plug release vessel (PPRV), which initially introduced by Brookhaven National Laboratory to meet those requirements. The PPRV works by allowing the gaseous form of the tracer to diffuse through the permeable silicone stopper and evaporate into the open air on the other side. The PFTs inside the vessels are injected as a liquid but instantly begin to convert to their gaseous phases at room temperature due to high vapor pressures (Zhang, H., Cloud, A.,2006). Previous studies have detailed how release rates change based on plug thickness across various temperatures (Jong et al., 2015), but not on the release rate stability based on temperature across multiple tracers. For use in underground mines passive release sources need to be durable, be simple to manufacture, have customizable and reliable release rates as well as a long operating life. The PPRV vessel provides a steady release of tracer gas that is essential for long term passive release experiments, making it a viable vessel for the PFTs being tested. The PPRV design also allows for vessels to be bundled together to achieve release rates at detectable levels and allows for the capability to run ventilation surveys with multiple tracers simultaneously. The ability to conduct ventilation surveys with multiple tracers using the PPRV bundling design and detection of the PFTs makes testing the tracers and design together a promising potential for complex and long term mine ventilations studies."

Jan 1, 2017

By Richard Emberley, Timothy Shaw, José L. Torero, Jurij Karlovsek, Timothy Gibson

"Tunnel closures are highly undesirable and the lengthiest are generally attributed to structural failures (e.g. Mont Blanc). Although historical data shows structural failures are closely linked to fire, design parameters for tunnel safety are not well defined. Current research has focused on defining the fire heat release rate and temperature, but these parameters cannot be easily used to determined structural performance. The energy transferred to the structure, the heat flux, is required but current literature lacks these values. Full scale experiments were undertaken on passenger vehicles resulting in heat fluxes between 20-70kW/m2. Analysis shows a vehicle fire’s duration is closely linked to its mass. Further analysis shows small vehicle fires can be scaled as a function of the tunnel diameter and the characteristic height of the desired vehicle. The present work provides engineers an appropriate design methodology to undertake informed thermal-structural analysis to minimize the risk of tunnel structural failure.INTRODUCTION Quantifying the effects of a tunnel fire depends on many factors such as the type of occupants, their vehicles and spacing, ventilation conditions and the geometric shape of the tunnel (Ingason and Lonnermark 2011). For design engineers investigating the thermal-structural performance of a tunnel, these factors are typically converted into spatial and temporal temperature distributions (Usmani et al. 2001) using various design curves such as those of ISO834-1, Hydrocarbon, Rijkswaterstaat (RWS) or RABT-ZTV (Promat 2013). However, to define a temperature profile through a structural element these curves require a heat transfer model that incorporates an appropriate boundary condition. The appropriate boundary condition is the net heat flux which is the result of a complex energy balance. For use in heat transfer calculations the net heat flux must account for the tunnel geometry as well as thermal properties of a given structural element and all other surfaces and mediums affecting the transfer of heat (Torero 2014)."

Jan 1, 2016

By Daniel R. Stewart

The function of the geological engineer is to assist in mine planning and operations by collecting, interpreting, and applying geologic data to the solution of engineering problems. The geologist supports this effort by collecting additional geologic information specifically useful to the engineer. This use of geologic information reinforces the value of mine geology to the mining process beyond the traditional role of orebody definition. Work discussed includes: evaluation of caving strategies at the Climax and Henderson mines; support definition and slope stability at the Climax mine; and some uses of geology in cavability estimation for the Mount Emmons project.

Jan 1, 1983

By K. Hopperstead

Ventilation planning in trackless metal mining is often taken for granted. This paper highlights the trials of planning and executing the ventilation design for Bog Zone at the Lisheen Mine. Ventilation planning for Bog Zone started at the feasibility study stage in 2003; subsequent design changes continued until 2006. In August 2006, the development of the Bog Zone ore body was accelerated through the use of contractors; in addition, the Lisheen equipment fleet was revised based on a larger load and haul fleet. As a result, the circuit was reviewed in terms of changes in design conditions and best practices. This review resulted in a 40% increase of total airflow required to mine Bog Zone. Resources utilized to design the circuit include: external review, computer modeling, and in-house Lisheen planning and operational staff review. The final ventilation design configuration was adopted in 2007, after modeling and evaluating 30 different scenarios, resulting in a better distribution of airflow, optimized secondary escape way, reduced contaminants, and a total power reduction. The value of investment in computer modeling of primary ventilation circuit and planning for staged implementation should never be underestimated.

Jan 1, 2009

By M. McPherson, P. Mousset-Jones, G. Danko

Calculation of the sensible heat transfer between the rock surface and the flowing air in an underground airway is still fraught with problems. There are only a few results available in the literature for the calculation of the convection in tunnels with naturally rough surfaces. Some of them are purely empirical, while others use a theoretical approach, based on the analogy between heat and momentum transfer, expressing the heat transfer coefficient as a function of the friction factor. A review and evaluation of these results are presented. The heat transfer equations obtained using the different assumptions, vary over a wide range, so that experimental results are needed to determine the formulae and constants applicable to mine airways. In situ measurements of the "physical" and "technical" heat transfer coefficient carried out in deep mines are described. The statistical distribution of the convective heat transfer coefficient on rough surfaces, as well as the regression between the Nusselt and Reynolds numbers in the turbulent flow region, are presented. Radiative heat transfer between the surface and the moist air flowing in a duct of relatively large hydraulic diameter has been taken into account during evaluation. The results will be a definite refinement of those calculations presently used in mine climate simulation models.

Jan 1, 1987

By S. Mendenhall

The Golden Sunlight Mine (GSM) began operation in 1982 with a strong commitment to environmental stewardship and the local community. This commitment ensured the long-term physical, chemical and ecological stability of the mine site and maintained an active partnership with local stakeholders. Concerns for economic development intensified as mine closure loomed on the horizon and fostered the inception of the Community Transition Advisory Committee(CTAC).This coalition of interested area stakeholders has the primary focus to sustain current mining operations while concurrently seeking alternative post-mine economic development opportunities utilizing existing mine assets. Accomplishments include development of an Asset Re-utilization and Post-closure Plan, a community survey regarding the impending mine closure, recruiting an international wind energy company to develop a wind farm, and development of an industrial/business park. The synergy of this strong partnership is key to meeting sustainability goals and enhancing potential future mining operations. The cooperative effort of the GSM and the local stakeholders is a success story that could be a role model for other mining operations.

Jan 1, 2004

By G. Ansong, P. K. Achireko

The authors present a new mineral price model, compare it with time series and naive models, and analyze the effects of the forecasting models on mineral project evaluation. Mineral commodity prices are volatile, which means that the results of evaluation tools that do not treat the stochasticity of metal prices rigorously may be misleading. But, in mine valuation, commodity price forecasts are required to assess the economic viability of a project. In this study, a new mineral forecasting method, called the MNDRVG-MFNN-RM model, which incorporates randomness, neural networks and regression models, is introduced. The MNDRVG-MFNN-RM model, a naive method and time series model were used to forecast gold prices for two successive years for the evaluation of a proposed open-pit mine. The MNDRVG-MFNN-RM model yielded the best results among the three methods. It produced the true optimum pit limits and an optimum pit value slightly less than the true optimum value. The main novelty of the methodology is the simulation and rigorous analysis of the randomness property associated with mineral prices to reduce the estimation and forecast errors, an important contribution to mineral venture evaluation, mine planning and design.

Jan 1, 2000

By Goutam H. Shahani

The current economic downturn has been at the center of media attention for several years. Today, the mining and mineral sectors are being impacted by highly fluctuating supply-and-demand conditions, extreme price volatility and tremendous market uncertainty on a world-wide basis. There have been numerous plant closings, project cancellations and employee layoffs. In this gloomy economic environment, it is easy to forget that the world?s gross domestic product (GDP) has more than doubled in real terms during the last 30 years. While current market turbulence may continue for some time, the long-term trend is unmistakably upward. Living standards are rising all over the world, thereby creating demand for food, clothing, transportation and housing. This translates into tremendous demand for the mining and mineral sectors. In the future, new capacity and plant expansions will be necessary to meet this need. These investments, which typically have a life span of 30-plus years, will have to be based on long-term economic considerations rather than current market conditions.

Jan 1, 2011

By S. D. F. Rocha

The influence of surfactants on the crystallization of calcium sulfate was investigated in both hatch and continuous systems. The investigation was per formed at the following conditions. 343 °K, 28% P205 and with a sulfate level of 2.0%. At concentrations of 5 and 200 µgig, respectively, dodecylbenzene sulfonic acid (DBSH) and sodium diisooctil sulosuccinate (SSNa) promoted both an increase in the size and a reduction in the length/width (L/W) ratio of the calcium sulfate hydrates produced in the hatch and continuous crystallizers. Unique effects were observed in the batch system at higher DBSH concentrations. At 10 µg/g, the precipitation of hemihydrate crystals with a distinct morphology and texture occurred under conditions where dihydrate precipitation was expected. Above 50 µg/g, the precipitation of calcium sulfate hydrates was completely inhibited.

Jan 1, 1996

By N. Lydakis ? Simantiris

Preliminary results of a mineralogical, geo-chemical and nutrient analysis of soil samples collected from Omalos polje-plateau are presented. This study is part of a project concerning the relationship of lithology and mineralogy characteristics of soils of different geological origin from the island of Crete with their chemical composition, and more specifically with their ionic nutrients content. The results presented in this work show a relatively good correlation of the mineralogy and the bulk content of the soils examined with the available nutrients in soil solution.

Jan 1, 2005

By Steven K. Duke, Jay Arabshahi

An economic, real-time probe drill monitoring system was developed for Metropolitan Water District’s Arrowhead Tunnels project to quantitatively evaluate ground conditions ahead of a TBM. This system digitally records hydraulic feed, rotation, and percussion pressures and calculates drill advance rates during drilling. These data are computer synthesized to develop a digital representation of the ground ahead, and the resulting “picture” of the ground is distributed to the project team to assist with tunnel construction decisions (i.e., targeting grout holes, optimizing mine-cycle lengths, and avoiding becoming stuck). The analysis and interpretation procedure has now been calibrated and refined using over 5,000 m (3 miles) of geologic face mapping data.

Jan 1, 2007

By H. Bernatowicz

The Nucoalyzer (On-Line Nuclear Analyzer) is a new method recently made comercially available for monitoring the elemental composition of a process stream. Applications for the Nucoalyzer include grading ore on a conveyor belt before or after it has gone through primary crushing, monitoring the slurry being transported in a pipe to the concentrator, and monitoring the stream of concentrate or the tailings from the concentrator. The Nucoalyzer may also be used at the smelter to monitor elements in the feed that include copper, sulfur, iron and silicon where a uniform feed is desired. The advantage of the Nucoalyzer over most other techniques are (a) it performs the measurement directly on the process with no sampling necessary, (b) the analysis can be performed on streams of particulate and slurries, and (c) the system does not have to make contact with the material it measures. These Nucoalyzers are operating at coal fired power plants and several more are about to be placed in service. This paper discusses the principles of operation of the Nucoalyzer, our experience in the field, application of minicomputers to data reduction, and potential applications in the ferrous and non-ferrous industries.

Jan 1, 1982

By Yuting Xue, Danqing Gao, Brijes Mishra

Heterogeneity and discontinuity significantly affect rock strength. For accurate stability prediction, intact rock behavior is imperatively included in rock mass behavior. However, past research largely used arbitrary scaling approaches to produce rock strength. This paper considers a stochastic approach in order to determine the strength of a rock. Based on the laboratory data, a MATLAB® with extreme value stochastic model generates a database for each physico-mechanical property. Then FLAC® simulates laboratory-sized rock specimens. The grids developed in the numerical model can in turn develop random material properties in MATLAB®, which researchers then applied to the final FLAC® model. Model runs simulate the approach performed in the laboratory. The results from the model indicate that a stochastic approach produces strengths that are lower than a deterministic approach. Failure modes for each specimen are different, similar to observations in the laboratory. In addition, random density also influences the failure mode, highlighting the importance of stochastic analysis in rocks.

By V. Paul Keran

Design of the Bajo de la Alumbrera project started in June 1995. Concentrate production began early in the third quarter of 1997. The project is situated in northwestern Argentina. Alumbrera is being developed by Minera Alumbrera, which is owned by MIM Holdings of Australia (50%), North Limited of Australia (25%) and Rio Algom of Canada (25%). Alumbrera is Argentina's first modern copper mine. This article outlines the key process- and plant-layout features that were incorporated in the Alumbrera concentrator design. It explains the background of flowsheet and equipment selection for the plant. A feature of the flowsheet is that it incorporates gravity-gold circuits in both the primary and the regrind circuits for recovery of gold to dore as well as in the copper concentrate product.

Jan 1, 1998